OM1905NKM OM1915NKM OM1912NKM HERMETIC TO-3 FIXED VOLTAGE NEGATIVE REGULATORS APPROVED TO DESC DRAWINGS Three Terminal, Fixed Voltage, 1.5 Amp Precision Negative Regulators In Hermetic JEDEC TO-3 Package FEATURES * * * * * * Output Voltages: -5V, -12V, -15V Output Voltages Set Internally to 1% Built-In Thermal Overload Protection Short Circuit Current Limiting Similar To Industry Standards 7905, 7912, 7915 Hi-Rel Screening Available DESCRIPTION These three terminal negative regulators are supplied in a hermetically sealed TO-3 metal package . All protective features are designed into the circuit, including thermal shutdown, current limiting and safe-area control. With heat sinking, they can deliver over 1.5 amps of output current. These units feature internally trimmed output voltages to 1% of nominal voltage. Standard voltages are -5V, -12V, -15V. These units are ideally suited for Military applications where a hermetically sealed package is required. PART NUMBER DESIGNATOR Standard Military Drawing Number 5962-8874601 YX 5962-8874701 YX 5962-8874801 YX 4 11 R0 3.3 - 87 Omnirel Part Number OM1905NKM OM1912NKM OM1915NKM 3.3 OM1905NKM - OM1915NKM ABSOLUTE MAXIMUM RATINGS @ 25C Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -35 V Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .- 55C to + 150C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to + 150C Typical Power/Thermal Charateristics: Rated Power @ 25 C TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20W TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6W Thermal Resistance qJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2C/W aa qJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42C/W ELECTRICAL CHARACTERISTICS -5 Volt VIN = -10V, Io = 500mA, -55C TA 125C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Output Voltage VOUT TA = 25C -4.95 -5.05 V -4.85 -5.15 V VIN = -7.5V to -20V * Unit IO = 5mA to 1.0 A, P< 20W Line Regulation VRLINE VIN = -7.5V to -20V (Note 1) (Note 4) Load Regulation 12 mV * 25 mV 5 mV * 12 mV 20 mV * 25 mV 15 mV * 30 mV VIN = -8.0V to -12V VRLOAD IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 2.5 mA 3.0 mA VIN = -7.0V to -20V * * 0.4 mA IO = 5mA to 1000mA * 0.4 mA * 2.5 V 3.3 A Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25C Short Circuit Current IDS VIN = -35V * (Note 2) 3.3 Ripple Rejection Output Noise Voltage 1.5 DVIN f =120 Hz, DVIN = -10V DVOUT (Note 3) NO TA = 25C, f =10 Hz to 100KHz * 1.2 A 2.8 A 63 dB 60 dB 40 (Note 3) V/V RMS Long Term Stability DVOUT (Note 3) Dt TA = 25C, t = 1000 hrs. 75 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range. 3.3 - 88 OM1905NKM - OM1915NKM ELECTRICAL CHARACTERISTICS -12 Volt VIN = -19V, Io = 500mA, -55C TA 125C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Output Voltage VOUT TA = 25C -11.88 -12.12 V -11.64 -12.36 V * VIN = -14.5V to -27V Unit IO = 5mA to 1.0 A, PD < 20W Line Regulation VRLINE VIN = -14.5V to -27V (Note 1) (Note 4) 20 mV * 50 mV 10 mV * 30 mV 32 mV * 60 mV 16 mV * 30 mV VIN = -16V to -22V Load Regulation VRLOAD IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 3.5 mA 4.0 mA VIN = -14.5V to -27V * * 0.8 mA IO = 5mA to 1000mA * 0.5 mA * 1.8 V Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25C, IO = 5mA to 1A Short Circuit Current IDS VIN = -35V DVIN f =120 Hz, DVIN = -10V 1.5 * (Note 2) Ripple Rejection 3.3 A 1.2 A 2.8 * dB DVOUT (Note 3) NO TA = 25C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25C, t = 1000 hrs. 120 (Note 3) Dt Output Noise Voltage A 56 53 dB (Note 3) V/V RMS mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. 3.3 MECHANICAL OUTLINE 1.197 1.53 REF. 1.177 0.875 MAX. 0.675 0.655 0.188 R. MAX. 0.135 MAX. 2 0.450 0.250 1 0.312 MIN. SEATING PLANE 0.043 0.038 0.225 0.205 0.161 0.151 2 PLCS. 3.3 - 89 0.525 R. MAX. 0.440 0.420 Pin Connection Pin 1: Ground Pin 2: Output Case: Input OM1905NKM - OM1915NKM ELECTRICAL CHARACTERISTICS -15 Volt VIN = -23V, Io = 500mA, -55C TA 125C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Output Voltage VOUT TA = 25C -14.85 -15.15 V -14.55 -15.45 V * VIN = -17.5V to -30V Unit IO = 5 mA to 1.0 A, PD < 20 W Line Regulation VRLINE VIN = -17.5V to -30V (Note 1) (Note 4) 25 mV * 50 mV 15 mV * 25 mV 35 mV * 75 mV 21 mV * 45 mV VIN = -20V to -26V Load Regulation VRLOAD IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 6.0 mA 6.5 mA VIN = -17.5V to -30V * * 0.8 mA IO = 5mA to 1000mA * 0.5 mA * 2.5 V Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25C Short Circuit Current IDS VIN = -35V DVIN f =120 Hz, DVIN = -10V 1.5 * (Note 2) Ripple Rejection 3.3 A 1.2 A 2.8 * dB DVOUT (Note 3) NO TA = 25C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25C, t = 1000 hrs. 150 (Note 3) Dt Output Noise Voltage A 53 50 dB V/V (Note 3) RMS mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. TYPICAL PERFORMANCE CHARACTERISTICS PEAK OUTPUT CURRENT RIPPLE REJECTION DROPOUT VOLTAGE 2.5 3.5 3 Tj = 100 2 80 IOUT = 1A VOUT = 5V 2 Tj = 25C 1.5 1 Tj = 150C 0.5 0 5 10 15 IOUT = 500mA 1 IOUT = 0A 0.5 DVOUT = 100MV DVOUT = 100mV 0 1.5 20 25 30 35 0 -75 -50 -25 0 25 50 75 100 125 150 Ripple Rejection (dB) Output Current (A) 2.5 Output Current (A) 3.3 60 40 VIN - V = 8VDC +3.5Vrms IOUT = 1A Tj = 25C 20 0 10 100 1k 10k 205 Crawford MA 01453 USA (508) 534-5776 FAX (508) 537-4246Frequency (Hz) Input To Output Differential (V) Street, Leominster, Junction Temperature (C) 205 Crawford Street, Leominster, MA 01453 USA (508) 534-5776 FAX (508) 537-4246 100k