SOLID TANTALUM ELECTROLYTIC CAPACITORS F72 F75 Low Profile Conformal coated Chip Maximum CV Conformal coated Chip Compliant to the RoHS directive (2002/95/EC). Specifications Item Per formance Characteristics Category --55 to + 125C (Rated temperature : + 85C) Temperature Range Capacitance Tolerance 20%, 10% (at 120Hz) Dissipation Factor (120Hz) ESR (100kHz) F72 F72 33 to 68F 6%Max. 100F or more 8%Max. 150F 10%Max. 220F to 330F 12%Max. 1000F 30%Max. 33F 47F 68F 100 to 330F 1000F F75 10%Max. 14%Max. 18%Max. 24%Max. 30%Max. 45%Max. 68 to 330F 470F 680F 1000F 1500F 2200F Less than 150F ~220F ~330F ~470 to 1500F ~2200F 0.90 0.80 0.75 0.70 0.14 0.22 0.20 0.15 0.12 0.07 * After 1 minute's application of rated voltage, leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. 1 2 3 4 5 6 7 8 9 10 Leakage Current 11 F 7 2 1 A 1 0 7 M R Taping code (Refer to page 309 for details) Case code Capacitance tolerance Rated capacitance Rated voltage Series Drawing H A not more than 0.125CV or 6.3A, whichever is greater. Capacitance Change by Temperature +15% Max. (at +125C) +10% Max. (at +85C) --10% Max. (at --55C) Damp Heat (Steady State) At 40C, 90 to 95% R.H., For 500 hours (No voltage applied) Capacitance Change * * * * * * Refer to * 1 Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * Initial specified value or less Temperature Cycles At --55C / +125C, 30 minutes each, For 5 cycles, Capacitance Change * * * * * * Refer to * 1 Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Currentv * * * * * * * * * * Initial specified value or less Resistance to Soldering Heat Reflow at 260C for 10 seconds, Dipping Flow at 260C for 10 seconds Capacitance Change * * * * * * Refer to * 1 Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * Initial specified value or less Surge After application of surge in series with a 33 resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85C, capacitors meet the characteristics requirements listed below. Capacitance Change * * * * * * Refer to * 1 Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * Initial specified value or less Endurance After 2000 hours' application of rated voltage at 85C, or derated voltage at 125C, capacitors meet the characteristic requirements listed below. Capacitance Change * * * * * * Refer to * 1 Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * Initial specified value or less Shear Test After applying the pressure load of 5N for 101 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. W Solder electrode Dimensions (mm) Case code L W H A B (D) R 7.2 0.3 6.0 0.3 1.2 0.3 1.3 0.4 3.8 0.6 (6.2) M 7.2 0.3 6.0 0.3 (6.2) 2.0MAX. F75 1.3 0.4 3.8 0.6 D dimension only for reference Type numbering system (Example : 16V 150F) 1 2 3 4 5 6 7 8 9 10 11 F 7 5 1 C 1 5 7 M D Taping code (Refer to page 309 for details) Case code Capacitance tolerance Rated capacitance Rated voltage Series Drawing H A B D L W Dimensions Case code L (mm) W H A B (D) C 7.1 0.3 3.2 0.3 2.5 0.3 1.3 0.3 3.6 0.6 (6.0) D 7.3 0.3 4.3 0.3 2.8 0.3 1.3 0.4 3.9 0.6 (6.4) R 7.2 0.3 6.0 0.3 3.5 0.3 1.3 0.4 3.8 0.6 (6.2) D dimension only for reference Standard Ratings F72 V Cap.(F) Code 033 336 047 476 068 686 100 107 150 4 0G 6.3 0J 10 1A 16 1C R R R R R R R R R 157 R R R 220 227 R R R 330 337 R R (R) 470 477 (M) (M) 680 687 1000 108 M 1500 158 (M) ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. more than 0.1CV or 5A, whichever is greater. * After 1 minute's application of derated voltage, leakage current at 125C is B D L * After 1 minute's application of rated voltage, leakage current at 85C is not 5N (0.51kg * f) For 10 1 seconds Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with 20 R230 Terminal Strength a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable 45 45 abnormality on the capacitor terminals. 1mm Type numbering system (Example : 10V 100F) As for the surge and derated voltage at 125C, refer to page 308 for details. *1 : C/C Item Damp Heat Tempereature cycles Resistance soldering heat Surge Endurance F75 F72 M 15 15 15 15 15 V Cap. (F) 068 100 150 220 330 470 680 1000 1500 2200 Code 686 107 157 227 337 477 687 108 158 228 4 0G Other 10 5 5 5 10 6.3 0J C C C*D D D*R R R C*D D D*R R 10 1A C C*D D R 16 1C C C D R CAT.8100Y