DS1847E-010 - Dallas Semiconductor

1 of 17 081502

SDA 1 14 Vcc

SCL 2 13 H0

A0 3 12 NC

A1 4 11 H1

A2 5 10 L1

WP 6 9 NC

GND 7 8 L0

14-Pin TSSOP (173-mil)

FEATURES

§ Two linear taper, temperature-controlled

variable resistors

§ DS1847-050

- One 50kW, 256 position

- One 10kW, 256 position

§ DS1847-010

- Two 10kW, 256 position

§ Resistor settings changeable every 2°C

§ Access to temperature data and device

control via a 2-wire interface

§ Operates from 3V or 5V supplies

§ Packaging: 14-pin TSSOP, 16-ball CSBGA

§ Operating temperature: -40ºC to +95ºC

§ Programming temperature: 0ºC to +70ºC

PIN ASSIGNMENT

DESCRIPTION

The DS1847 Dual Temperature-Controlled Nonvolatile (NV) Variable Resistor consists of two 256-

position linear, variable resistors. The DS1847-050 consists of one 10kW and one 50kW, while the

DS1847-010 consists of two 10kW resistors; both incorporate a direct-to-digital temperature sensor. The

device provides an ideal method for setting and temperature-compensating bias voltages and currents in

control applications using a minimum of circuitry.

The variable resistors settings are stored in EEPROM memory and can be accessed over the industry

standard 2-wire serial bus. The value of each variable resistor is determined by a temperature-addressed

look-up table, which can assign a unique value to each resistor for every 2°C increment over the -40°C to

+95°C range. The output of the digital temperature sensor is also available as a 13-bit, 2’s complement

value over the serial bus. The interface I/O pins consist of SDA and SCL.

DS1847

Dual Temperature-Controlled

NV Variable Resistor

www.maxim-ic.com

1 2 3 4

Top View

16-Ball CSBGA (4mm x 4mm)

DS1847

2 of 17

PIN DESCRIPTIONS

Name TSSOP BGA Description

VCC 14 A3 Power Supply Terminal. The DS1847 will support supply

voltages ranging from +3.0V to +5.5V.

GND 7 D1 Ground Terminal.

SDA 1 B2 2-Wire Serial Data Interface. The serial data pin is for serial data

transfer to and from the DS1847. The pin is open drain and may

be wire-ORed with other open drain or open collector interfaces.

SCL 2 A2 2-Wire Serial Clock Input. The serial clock input is used to

clock data into the DS1847 on rising edges and clock data out on

falling edges.

WP 6 C1 Write Protect Input. If open or set to logic 1, all memory, control

registers, and Look-up tables are write protected. If set to a logic 0, the

device is not write protected and can be written to. The WP pin is pulled

high internally.

A0 3 A1 Address Input. Pins A0, A1, and A2 are used to specify the

address of each DS1847 when used in a multi-dropped

configuration.

A1 4 B1 Address Input.

A2 5 C2 Address Input.

H0 13 A4 High terminal of Resistor 0. For both resistors, it is

not required that the high terminal be connected to a potential

greater than the low terminal. Voltage applied to the high terminal

of each resistor cannot exceed VCC, or go below ground.

H1 11 B3 High terminal of Resistor 1.

L0 8 D3 Low terminal of Resistor 0. For both resistors, it is

not required that the low terminal be connected to a potential less

than the high terminal. Voltage applied to the low terminal of each

resistor cannot exceed VCC, or go below ground.

L1 10 C4 Low terminal of Resistor 1.

NC 9 D4 No Connect.

NC 12 B4 No Connect.

NC C3 No Connect.

NC D2 No Connect.

DS1847

3 of 17

DS1847 BLOCK DIAGRAM Figure 1

2-Wire

Interface

Digital

Temperature

Sensor

256 Position

Digitally-

Controlled

10kW or 50kW

Resistor 0

256 Position

Digitally-

Controlled 10kW

Resistor 1

SDA

SCL

72x8 bit

EEPROM

Resistor 0

Look-up Table

(Table 1)

72x8 bit

EEPROM

Resistor 1

Look-up Table

(Table 2)

VCC

Gnd

Table Select Byte

Configuration

Byte

Temperature

MSB Byte

Temperature

LSB Byte

Address Pointer

User Memory

Internal Address

Select

User Memory

Resistor 0 Setting

Resistor 1 setting

User Memory

E0h

E1h

E2h

E3h

E4h

E5h-

E6h

E7h

E8h-

EFh

F0h

F1h

F2h-

FFh

47h

DS1847

4 of 17

Memory

Location

Name of Location Function of Location

00h to 47h

(Table Select

Byte, E0h, must

be set to 01h or

02h to access the

Look-Up Tables)

User Defined Look-Up Table

(LUT)

This block contains the user defined temperature

settings of the resistors. Values between 00h and

FFh can be written to either table to set the 256

position variable resistors. The first address

location, 00h, is used to set the resistor at -40°C.

Each successive memory location will contain the

resistor setting for the previous temperature +2°C.

For example, memory address 01h is the address

that will set the resistor in a –38°C environment.

For default memory settings and programming

the look-up table, refer to the Programming the

Look-Up Table (LUT) section of the datasheet.

E0h Table Select Byte Writing to this byte determines which of the two

72x8 EEPROM look-up tables is selected for

reading or writing.

01h (Look-Up Table 1 selected)

02h (Look-Up Table 2 selected)

E1h Configuration Byte

TAU – Temperature/Address Update

TEN – Temperature Update Enable

AEN – Address Update Enable

Default setting is 03h, TAU = 1, TEN = 1 and

AEN = 1.

TAU becomes a 1 after a temperature and address

update has occurred as a result of a temperature

conversion. The user can write this bit to 0 and

check for a transition from 0 to 1 in order to

verify that a conversion has occurred.

If TEN = 0, the temperature conversion feature is

disabled. The user sets the resistor in “manual

mode” by writing to addresses F0h and

F1h to control resistors 0 and 1, respectively.

With AEN = 0 the user can operate in a test

mode. Address updates made from the

temperature sensor will cease. The user can load a

memory location into E4h and verify that the

values in locations F0h and F1h are the expected

user-defined values.

TAU TEN AEN

DS1847

5 of 17

Memory

Location

Name of Location Function of Location

E2h Temperature MSB This byte contains the MSB of the 13-bit 2s

complement temperature output from the

temperature sensor.

E3h Temperature LSB This byte contains the LSB of the 13-bit 2s

complement temperature output from the

temperature sensor.

For example temperature readings, refer to Table

E4h Address Pointer Calculated, current resistor address (0h – 47h).

The user-defined resistor setting at this location in

the respective look-up table will be loaded into

F0h and F1h to set the two resistors.

E5h to E6h User Memory General purpose user memory (SRAM)

E7h Address Select Internal or external device address select. This

byte allows the user to use the external address

pins or an internal register location to determine

the device address.

ENB = 0 and external A2, A1, A0 grounded,

device will use internal address bits (A2, A1, A0)

in this register

ENB = 1, external A2, A1, A0 = any setting,

device will use external address pins

Default setting is 01h. The device uses external

pins to determine its address.

E8h to EFh User Memory General purpose user memory (SRAM)

F0h Resistor 0 Setting In the user-controlled setting mode, this block

contains the resistor 0 setting.

F1h Resistor 1 Setting In the user-controlled setting mode, this block

contains the resistor 1 setting.

F2h to FFh User memory General purpose user memory (SRAM)

A2 A1 A0 ENB

20 2-1 2-2 2-3 2-4 X X X

S 2

DS1847

6 of 17

PROGRAMMING THE LOOK-UP TABLE (LUT)

The following equation can be used to determine which resistor position setting, 00h – FFh, should be

written in the LUT to achieve a given resistance at a specific temperature.

()()

[

]

() ( ) ( )

[]

aa -

-·+-·+·

-·+-·+·-

25251

),,( CzCyx

CwCvuR

CRpos

DS1847-050

a = 3.78964 for the 50kW resistor

a = 19.74866 for the 10kW resistor

DS1847-010

a = 8.394533 for both 10kW resistors

R = resistance desired at the output terminal

C = temperature in degrees Celsius

u, v, w, x, y, and z are calibration constants programmed into each of the corresponding look-up tables.

Their addresses and LSB values are given in Table 1. Resistor 1 variables are found in Look-Up Table 1

of the EEPROM, and Resistor 2 variables are found in Look-Up Table 2. After these values are read, they

should be overwritten with the appropriate temperature-specific resistance settings.

LOOK-UP VARIABLE ADDRESSES Table 1

Address in

LUT (HEX)

Variable LSB

28 – 29 u 2-8

2A – 2B v 10-6

2C – 2D w 10-9

2E – 2F x 2-8

30 – 31 y 10-7

32 – 33 z 10-10

When shipped from the factory, all other memory locations in the LUTs are programmed to FFh (except

bytes 00h-07h of Table 1 and 2 which may be factory programmed to values other than FFh).

Note: Memory locations 44h – 47h, which cover the temperature range (+96ºC to +102ºC), are outside

of the specified operating temperature range (-40ºC to +95ºC). However, the values stored in these

locations will act as valid resistance settings if the temperature exceeds +95ºC. Therefore, Dallas

Semiconductor recommends that the user programs a resistance value into all LUT locations. Failure to

do so will result in the part being set to the default value.

DS1847

7 of 17

TEMPERATURE CONVERSION

The direct-to-digital temperature sensor measures temperature through the use of an on-chip temperature

measurement technique with an operating range from -40°C to +95°C. Temperature conversions are

initiated upon power-up, and the most recent result is stored in address locations E2h and E3h, which are

updated every 10ms. Temperature conversion will not occur during an active read or write to memory.

The value of each resistor is determined by the temperature-addressed look-up table that assigns a unique

value to each resistor for every 2°C increment with a 1°C hysteresis at a temperature transition over the

operating temperature range. This can be seen in Figure 2.

TEMPERATURE CONVERSION HYSTERESIS Figure 2

EXAMPLE TEMPERATURE READINGS Table 2

TEMP BINARY DATA HEX DATA

+95ºC 0010 1111 1000 0000 2F80h

+25.0625ºC 0000 1100 1000 1000 0C88h

-10.125ºC 1111 1010 1111 0000 FAF0h

-40ºC 1110 1100 0000 0000 EC00h

2 4 6 8 10 12

TEMPERATURE (C)

MEMORY LOCATION

Increasing temp

Decreasing temp

DS1847

8 of 17

2-WIRE OPERATION

Clock and Data Transitions: The SDA pin is normally pulled high with an external resistor or device.

Data on the SDA pin may only change during SCL low time periods. Data changes during SCL high

periods will indicate a start or stop conditions depending on the conditions discussed below. Refer to the

timing diagram (Figure 4) for further details.

Start Condition: A high-to-low transition of SDA with SCL high is a start condition that must precede

any other command. Refer to the timing diagram (Figure 4) for further details.

Stop Condition: A low-to-high transition of SDA with SCL high is a stop condition. After a read

sequence, the stop command places the DS1847 into a low-power mode. Refer to the timing diagram

(Figure 4) for further details.

Acknowledge Bit: All address and data byte are transmitted via a serial protocol. The DS1847 pulls the

SDA line low during the ninth clock pulse to acknowledge that it has received each word.

Standby Mode: The DS1847 features a low-power mode that is automatically enabled after power-on,

after a stop command, and after the completion of all internal operations.

2-Wire Interface Reset: After any interruption in protocol, power loss, or system reset, the following

steps reset the DS1847:

1. Clock up to nine cycles.

2. Look for SDA high in each cycle while SCL is high.

3. Create a START condition while SDA is high.

Device Addressing: The DS1847 must receive an 8-bit device address word following a START

condition to enable a specific device for a read or write operation. The address word is clocked into the

DS1847 MSB to LSB. The address word consists of Ah (1010) followed by A2, A1, and A0 then the

R/W (READ/WRITE) bit. If the R/W bit is high, a read operation is initiated. If the R/W is low, a write

operation is initiated. For a device to become active, the values of A2, A1 and A0 must be the same as the

hard-wired address pins on the DS1847. Upon a match of written and hard-wired addresses, the DS1847

will output a zero for one clock cycle as an acknowledge. If the address does not match, the DS1847

returns to a low-power mode.

Write Operations: After receiving a matching address byte with the R/W bit set low, the device goes

into the write mode of operation. The master must transmit an 8-bit EEPROM memory address to the

device to define the address where the data is to be written. After this byte has been received, the DS1847

will transmit a zero for one clock cycle to acknowledge the receipt of the address. The master must then

transmit an 8-bit data word to be written into this address. The DS1847 will again transmit a zero for one

clock cycle to acknowledge the receipt of the data. At this point, the master must terminate the write

operation with a STOP condition. The DS1847 then enters an internally timed write process tw to the

EEPROM memory. All inputs are disabled during this byte write cycle.

The DS1847 is capable of an 8-byte page write. A page write is initiated the same way as a byte write, but

the master does not send a STOP condition after the first byte. Instead, after the slave acknowledges

receipt of the data byte, the master can send up to seven more bytes using the same nine-clock sequence.

DS1847

9 of 17

The master must terminate the write cycle with a STOP condition or the data clocked into the DS1847

will not be latched into permanent memory.

Acknowledge Polling: Once the internally-timed write has started and the DS1847 inputs are disabled,

acknowledge polling can be initiated. The process involves transmitting a START condition followed by

the device address. The R/W bit signifies the type of operation that is desired. The read or write sequence

will only be allowed to proceed if the internal write cycle has completed and the DS1847 responds with a

zero.

Read Operations: After receiving a matching address byte with the R/W bit set high, the device goes

into the read mode of operation. There are three read operations: current address read, random read, and

sequential address read.

CURRENT ADDRESS READ

The DS1847 has an internal address register that maintains the address used during the last read or write

operation, incremented by one. This data is maintained as long as VCC is valid. If the most recent address

was the last byte in memory, then the register resets to the first address. This address stays valid between

operations as long as power is available.

Once the device address is clocked in and acknowledged by the DS1847 with the R/W bit set to high, the

current address data word is clocked out. The master does not respond with a zero, but does generate a

STOP condition afterwards.

RANDOM READ

A random read requires a dummy byte write sequence to load in the data word address. Once the device

and data address bytes are clocked in by the master and acknowledged by the DS1847, the master must

generate another START condition. The master now initiates a current address read by sending the device

address with the read/write bit set high. The DS1847 will acknowledge the device address and serially

clocks out the data byte.

SEQUENTIAL ADDRESS READ

Sequential reads are initiated by either a current address read or a random address read. After the master

receives the first data byte, the master responds with an acknowledge. As long as the DS1847 receives

this acknowledge after a byte is read, the master may clock out additional data words from the DS1847.

After reaching address FFh, it resets to address 00h.

The sequential read operation is terminated when the master initiates a stop condition. The master does

not respond with a zero.

For a more detailed description of 2-wire theory of operation, refer to the next section.

DS1847

10 of 17

2-WIRE SERIAL PORT OPERATION

The 2-wire serial port interface supports a bi-directional data transmission protocol with device

addressing. A device that sends data on the bus is defined as a transmitter, and a device receiving data as

a receiver. The device that controls the message is called a “master.” The devices that are controlled by

the master are “slaves.” The bus must be controlled by a master device that generates the serial clock

(SCL), controls the bus access, and generates the START and STOP conditions. The DS1847 operates as

a slave on the 2-wire bus. Connections to the bus are made via the open-drain I/O lines SDA and SCL.

The following I/O terminals control the 2-wire serial port: SDA, SCL, A0, A1, A2. Timing diagrams for

the 2-wire serial port can be found in Figures 3 and 4. Timing information for the 2-wire serial port is

provided in the AC Electrical Characteristics Table for 2-wire serial communications.

The following bus protocol has been defined:

§ Data transfer may be initiated only when the bus is not busy.

§ During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in

the data line while the clock line is HIGH will be interpreted as control signals.

Accordingly, the following bus conditions have been defined:

Bus not busy: Both data and clock lines remain HIGH.

Start data transfer: A change in the state of the data line from HIGH to LOW while the clock is HIGH

defines a START condition.

Stop data transfer: A change in the state of the data line from LOW to HIGH while the clock line is

HIGH defines the STOP condition.

Data valid: The state of the data line represents valid data when, after a START condition, the data line

is stable for the duration of the HIGH period of the clock signal. The data on the line can be changed

during the LOW period of the clock signal. There is one clock pulse per bit of data. Figures 3 and 4 detail

how data transfer is accomplished on the 2-wire bus. Depending upon the state of the R/W bit, two types

of data transfer are possible.

Each data transfer is initiated with a START condition and terminated with a STOP condition. The

number of data bytes transferred between START and STOP conditions is not limited and is determined

by the master device. The information is transferred byte-wise and each receiver acknowledges with a

ninth bit.

Within the bus specifications a regular mode (100kHz clock rate) and a fast mode (400kHz clock rate) are

defined. The DS1847 works in both modes.

Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the

reception of each byte. The master device must generate an extra clock pulse that is associated with this

acknowledge bit.

A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a

way that the SDA line is a stable LOW during the HIGH period of the acknowledge-related clock pulse.

Of course, setup and hold times must be taken into account. A master must signal an end of data to the

DS1847

11 of 17

slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this

case, the slave must leave the data line HIGH to enable the master to generate the STOP condition.

1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the master is

the command/control byte. Next follows a number of data bytes. The slave returns an acknowledge bit

after each received byte.

2. Data transfer from a slave transmitter to a master receiver. The master transmits the first byte (the

command/control byte) to the slave. The slave then returns an acknowledge bit. Next, follows a

number of data bytes transmitted by the slave to the master. The master returns an acknowledge bit

after all received bytes other than the last byte. At the end of the last received byte, a ‘not

acknowledge’ can be returned.

The master device generates all serial clock pulses and the START and STOP conditions. A transfer is

ended with a STOP condition or with a repeated START condition. Since a repeated START condition is

also the beginning of the next serial transfer, the bus will not be released.

The DS1847 may operate in the following two modes:

1. Slave receiver mode: Serial data and clock are received through SDA and SCL, respectively. After

each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized

as the beginning and end of a serial transfer. Address recognition is performed by hardware after

reception of the slave (device) address and direction bit.

2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.

However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data

is transmitted on SDA by the DS1847, while the serial clock is input on SCL. START and STOP

conditions are recognized as the beginning and end of a serial transfer.

3. Slave Address: Command/control byte is the first byte received following the START condition from

the master device. The command/control byte consists of a 4-bit control code. For the DS1847, this is

set as 1010 binary for read/write operations. The next 3 bits of the command/ control byte are the

device select bits or slave address (A2, A1, A0). They are used by the master device to select which

of eight devices is to be accessed. When reading or writing the DS1847, the device-select bits must

match the device-select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines

the operation to be performed. When set to a 1, a read operation is selected, and when set to a 0, a

write operation is selected.

Following the START condition, the DS1847 monitors the SDA bus checking the device type identifier

being transmitted. Upon receiving the 1010 control code, the appropriate device address bits, and the

read/write bit, the slave device outputs an acknowledge signal on the SDA line.

WRITE PROTECT

The write-protect input pin (WP) protects all memory (including EEPROM), control registers, and look-

up tables from alteration in an application. However, this does not interfere with internal

temperature/resistor updates. If set to a logic 0, the device is not write protected and can be written to via

the 2-wire interface. This pin has an internal pull-up resistor.

DS1847

12 of 17

2-WIRE DATA TRANSFER PROTOCOL Figure 3

2-WIRE AC CHARACTERISTICS Figure 4

DS1847

13 of 17

ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground -0.3V to +6.0V

Operating Temperature -40°C to +95°C

Programming Temperature 0°C to +70°C

Storage Temperature -55°C to +125°C

Soldering Temperature See J-STD-020A specification

* This is a stress rating only and functional operation of the device at these or any other conditions above

those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

RECOMMENDED DC OPERATING CONDITIONS (-40°C to +95°C)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Supply Voltage Vcc +3.0 5.5 V 1

Resistor Inputs L0, L1,

H0, H1 GND-0.3 VCC+0.3 V

Resistor Current IRESISTOR DS1847-050

DS1847-010

-1

-3

3mA

DC ELECTRICAL CHARACTERISTICS (-40°C to +95°C; VCC = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Supply Current ICC 0.5 1 mA 2

Input Leakage

(digital inputs)

IL-1 +1 µA

Input Leakage (H0,

H1, L0, and L1)

IL-100 +100 nA

Input Logic 1 VIH 0.7VCC VCC+0.3 V 15

Input Logic 0 VIL GND-0.3 0.3VCC V

Input Current each

I/O pin

0.4<VI/O<0.9VCC -10 +10 mA13

VOL1 3mA sink current 0.0 0.4 V

Low Level Output

Voltage (SDA) VOL2 6mA sink current 0.0 0.6 V

I/O Capacitance CI/O 10 pF

WP Internal Pull Up

Resistance, Rwp

Rwp 40 65 100 kW

DS1847

14 of 17

ANALOG RESISTOR CHARACTERISTICS (-40°C to +95°C; VCC = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Absolute Error using cal. values -4 +4 LSB 14

Position FFh Resistance

DS1847-050

DS1847-010

(50k resistor)

(10k resistor)

44.6

9.0

8.0

55.8

11.3

10.0

67.0

13.6

12.0

kW3

Position 00h Resistance

DS1847-050

DS1847-010

(50k resistor)

(10k resistor)

500

250

850

425

1200

600

Absolute Linearity -2 +2 LSB 4

Relative Linearity -1 +1 LSB 5

Compensated Tempco

Error

using calibration

values

-4 +4 LSB 14

Uncompensated Tempco 850 ppm/°C 12

DIGITAL THERMOMETER

PARAMETER SYMBOL CONDITION TYP MAX UNITS NOTES

Thermometer Error TERR -40°C to 95°C ±3.0 °C

Conversion Time tCONVT 12-bit conversion 10 ms

DS1847

15 of 17

AC ELECTRICAL CHARACTERISTICS (-40°C to +95°C, VCC = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

SCL clock frequency fSCL Fast Mode

Standard Mode

400

100

kHz 6

Bus free time between

STOP and START

tBUF Fast Mode

Standard Mode

1.3

4.7

ms6

Hold time (repeated)

START condition

t HD:STA Fast Mode

Standard Mode

0.6

4.0

ms7, 6

Low period of SCL clock tLOW Fast Mode

Standard Mode

1.3

4.7

ms6

High period of SCL clock tHIGH Fast Mode

Standard Mode

0.6

4.0

ms6

Data hold time tHD:DAT Fast Mode

Standard Mode

00.9 ms6, 8, 9

Data set-up time tSU:DAT Fast Mode

Standard Mode

100

250

ns 6

Start set-up time tSU:STA Fast Mode

Standard Mode

0.6

4.7

ms6

Rise time of both SDA

and SCL signals

tRFast Mode

Standard Mode 20+0.1CB

300

1000

ns 10

Fall time of both SDA

and SCL signals

tFFast Mode

Standard Mode 20+0.1CB

300

ns 10

Set-up time for STOP

condition

tSU:STO Fast Mode

Standard Mode

0.6

4.0

Capacitive load for each

bus line

CB400 pF 10

EEPROM write time tW520ms 11

NONVOLATILE MEMORY CHARACTERISTICS

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

Writes 85°C 50,000

DS1847

16 of 17

NOTES:

1. All voltages are referenced to ground.

2. Inputs SDA = SCL = WP = VCC. A0, A1, and A2, must be tied to VCC or GND.

3. Valid at 25°C only.

4. Absolute linearity is the difference of measured value from expected value at DAC position.

Expected value is a straight line from measured minimum position to measured maximum position.

5. Relative linearity is the deviation of an LSB DAC setting change vs. the expected LSB change.

Expected LSB change is the slope of the straight line from measured minimum position to measured

maximum position.

6. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250ns must

then be met. This will automatically be the case if the device does not stretch the LOW period of the

SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next

data bit to the SDA line tRMAX + tSU:DAT = 1000ns + 250ns = 1250ns before the SCL line is released.

7. After this period, the first clock pulse is generated.

8. The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the

SCL signal.

9. A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the

VIHMIN of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.

10. CB – total capacitance of one bus line in picofarads, timing referenced to 0.9VCC and 0.1VCC.

11. EEPROM write begins after a STOP condition occurs.

12. The temperature coefficient varies with resistor position from 650ppm/°C at position FFh to

1000ppm/°C at 00h (for the 50k resistor), or 1500ppm/°C at 00h (for the 10k resistor). See the graphs

below. The tempco can be significantly reduced by using the resistor calibration values. When doing

so, the average tempco over the entire temperature range is between 200ppm°/C (for the lower

positions) and 10ppm/°C (higher positions). Refer to the Programming the Look-Up Table section of

the data sheet.

13. I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VCC is switched off.

14. Refer to Programming the Look-Up Table section of the data sheet for calibration.

15. Address input A1 passes Latch-up per JEDEC 78 class I. All other pins pass class II.

TEMPCO vs. RESISTANCE

10K RESISTOR

500

600

700

800

900

1000

1100

1200

1300

1400

1500

0 2000 4000 6000 8000 10000

RESISTANCE (OHMS)

PPM/°C

TEMPCO vs. RESISTANCE

50K RESISTOR

500

600

700

800

900

1000

1100

0 10000 20000 30000 40000 50000

RESISTANCE (OHMS)

PPM/°C

DS1847

17 of 17

ORDERING INFORMATION

ORDERING

NUMBER

PACKAGE OPERATING

TEMPERATURE

VERSION

Resistor 0

/Resistor 1

DS1847E-010 14-PIN TSSOP (173-MIL) -40ºC TO +95ºC 10kW/10kW

DS1847E-050 14-PIN TSSOP (173-MIL) -40ºC TO +95ºC 50kW/10kW

DS1847E-010/T&R 14-PIN TSSOP/TAPE & REEL -40ºC TO +95ºC 10kW/10kW

DS1847E-050/T&R 14-PIN TSSOP/TAPE & REEL -40ºC TO +95ºC 50kW/10kW

DS1847B-010 16-BALL CSBGA -40ºC TO +95ºC 10kW/10kW

DS1847B-050 16-BALL CSBGA -40ºC TO +95ºC 50kW/10kW