D2VW5L1B1MS - OMRON - Datasheet.Live

Sealed Snap Action Switch D2VW 1

Sealed Snap Action Switch

D2VW

Watertight Miniature Snap Action Switch

• High-quality watertight, high-precision miniature Snap

Action switch. Switch Body meets IP67 requirements

• Use of epoxy resin assures high sealing capability and is

ideal for dusty places or where water is sprayed

• V-series internal mechanism assures high precision and

long life

• General-load (5 A at 250 VAC) models and micro-load

models are available

• RoHS Compliant

Ordering Information

Note: 1. The standard lengths of the lead wires (UL1015 AWG20 for UL/CSA models, AV0.75f otherwise) of models incorporating them are 300 mm.

Add “-0” to the end of the part number to obtain 1,000 mm long wires. (e.g.: D2VW-5L2A-1MS-0)

2. Remove “-HS” from the end of solder/quick-connect models to obtain non-UL/CSA versions. (e.g.: D2VW-01-1HS →D2VW-01-1)

3. Remove “S” from the end of lead wire models to obtain non-UL/CSA versions with AV0.75f wire. (e.g.: D2VW-5L3-1MS →D2VW-5L3-1M)

Model Number Legend

Actuator Terminal Model

Model 0.1 A Model 5 A

Pin plunger With solder and #187 tab terminals D2VW-01-1HS D2VW-5-1HS

With lead wires D2VW-01-1MS D2VW-5-1MS

Short hinge lever With solder and #187 tab terminals D2VW-01L1A-1HS D2VW-5L1A-1HS

With lead wires D2VW-01L1A-1MS D2VW-5L1A-1MS

Hinge lever With solder and #187 tab terminals D2VW-01L1-1HS D2VW-5L1-1HS

With lead wires D2VW-01L1-1MS D2VW-5L1-1MS

Long hinge lever With solder and #187 tab terminals D2VW-01L1B-1HS D2VW-5L1B-1HS

With lead wires D2VW-01L1B-1MS D2VW-5L1B-1MS

Simulated roller lever With solder and #187 tab terminals D2VW-01L3-1HS D2VW-5L3-1HS

With lead wires D2VW-01L3-1MS D2VW-5L3-1MS

Short hinge roller lever With solder and #187 tab terminals D2VW-01L2A-1HS D2VW-5L2A-1HS

With lead wires D2VW-01L2A-1MS D2VW-5L2A-1MS

Hinge roller lever With solder and #187 tab terminals D2VW-01L2-1HS D2VW-5L2-1HS

With lead wires D2VW-01L2-1MS D2VW-5L2-1MS

D2VW- - -

1. Ratings

5: 5 A at 250 VAC

01: 0.1 A at 30 VDC

2. Actuator

None: Pin plunger

L1A: Short hinge lever

L1: Hinge lever

L1B: Long hinge lever

L3: Simulated roller lever

L2A: Short hinge roller lever

L2: Hinge roller lever

3. Contact Form

1: SPDT

2: SPST-NC

3: SPST-NO

4. Terminals

None, HS: Solder terminals

(HS for UL and CSA approval.)

M, MS: Molded lead wires

5. Length of the molded lead wire

None: 300 mm

0: 1,000 mm

(MS for UL and CSA approval)

3 4 521

2Sealed Snap Action Switch D2VW

Specifications

■Characteristics

Note: 1. Data shown are of initial value.

2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.

3. For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, the values

apply at the total travel position.

4. The operating temperature of the lead wire (AV0.75f) for non-UL/CSA molded lead wire models is between -40 to 85°C.

■Ratings (reference values)

D2VW-5

D2VW-01

Note: 1. The resistive load ratings apply under the following test conditions:

Ambient Temperature = 20±2°C, Ambient Humidity = 65±5%, Operating frequency = 30 operations/min.

2. The above current ratings are the values of the steady-state current.

3. Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC).

4. Lamp load has an inrush current of 10 times the steady-state current.

5. Rating for UL/CSA approval is as follows (See “Approved Standards” section):

Model D2VW-01 D2VW-5

Operating speed 0.1 mm to 1 m/s (at pin plunger)

Operating frequency Mechanical: 300 operations/minute max.

Electrical: 60 operations/minute max.

Insulation resistance 100 MΩmin. (at 500 VDC)

Contact resistance 50 mΩmax. for solder terminal models

100 mΩmax. for 300 mm molded lead wire models

200 mΩmax. for 1,000 mm molded lead wire models

Dielectric strength (See note 2) 1,000 VAC, 50/60 Hz for 1 min. between terminals of the same polarity

1,500 VAC, 50/60 Hz for 1 min. between each current-carrying metal parts and ground, and

between each terminal and non-current-carrying metal parts.

Vibration resistance (See note 3) Malfunction: 10 to 55 Hz, 1.5 mm double amplitude

Shock resistance (See note 3) Destruction: 1,000 m/s2(approx. 100G) max.

Malfunction: 300 m/s2(approx. 30G) max.

Degree of protection IEC IP67 (excluding the terminals on terminal models).

Degree of protection against electric shock Class I

Proof tracking index (PTI) 175

Ambient operating temperature -40°to 85°C (at 60% RH max.) with no icing

Ambient operating humidity 95% max. (for 5°Cto35°C)

Life expectancy Mechanical 10,000,000 operations min. at 60 operations per minute

Electrical

1,000,000 operations min. at 30 ops. per minute.

100,000 operations min. at 30 ops. per minute

Weight Approx. 7g (pin plunger models without wires)

Rated Voltage Non-inductive load Inductive load

Resistive load Lamp load Inductive load Motor load

NC NO NC NO NC NO NC NO

125 VAC 5 A 0.5 A 4 A —

250 VAC 5 A 0.5 A 4 A —

30VDC 5A 3A 4A —

125 VDC 0.4 A 0.1 A 0.4 A —

Rated Voltage Non-inductive load Inductive load

Resistive load Lamp load Inductive load Motor load

NC NO NC NO NC NO NC NO

125 VAC 0.1 A — — —

30 VDC 0.1 A — — —

D2VW-01 0.1A @ 125 VAC

0.1A @ 30 VDC

D2VW-5 3A @ 125 VAC, 250 VAC

Sealed Snap Action Switch D2VW 3

■Approved Standards

Consult your OMRON sales representative for specific models with

standard approvals.

UL Recognized, CSA Certified

EN 61058-1 (VDE Approval)

Testing conditions:

25E3 (25,000 operations), T55 (0°Cto55°C) for D2VW-5

1E5 (100,000 operations), T85 (0°Cto85°C) for D2VW-01

■Contact Specifications

Note: Minimum applicable loads are indicated by N standard refer-

ence values. This value represents the failure rate at a 60%

(λ60) reliability level (JIS C5003).

The equation λ60=0.5 x 10-6 / operations indicates that a failure

rate of less than 1/2,000,000 operations can be expected at a

reliability level of 60%

Engineering Data

■Structure

■Mounting

All switches may be panel mounted using M3 mounting screws with

plane washers or spring washers to securely mount the switch.

Tighten the screws to a torque of 0.39 to 0.59 N·m.

Rated Voltage D2VW-5 D2VW-01

125 VAC

250 VAC

0.1 A

---

30 VDC - - - 0.1 A

Rated Voltage D2VW-5 D2VW-01

125 VAC

250 VAC

---

0.1 A

---

Item D2VW-5 D2VW-01

Specification Rivet Crossbar

Material Silver alloy Gold alloy

Gap (standard value) 0.5 mm

Inrush current NC: 15 A max.

NO: 15 A max. ---

Minimum applicable load

(see note)

160 mA at 5 VDC 1 mA at 5 VDC

NC (red)

NO (blue)

COM (black)

SPDT

NC (red)

COM (black)

SPST-NC

NO (blue)

COM (black)

SPST-NO

Note: Colors in parentheses indicate lead wire colors.

Two, 3.1-dia. mounting holes or

M3 screw holes

22.2 ± 0.1

10.3 ± 0.1

4Sealed Snap Action Switch D2VW

Dimensions

■Terminals

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

2. The pin plunger model is shown here as a typical example for both the solder/quick connect terminals and the molded lead wire versions.

■Dimensions and Operating Characteristics

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

2. Omitted dimensions are the same as pin plunger type.

3. The operating characteristics are for operation in the A direction( )

Solder/Quick Connect Terminals

t=0.5

Three, solder terminals

1.3 dia. hole2.4 dia. hole

8.4

5.2

1.2

4.810.3

2.5

5.2

41.4

22.2±0.1

0.5

2.8

Molded Lead Wires

* UL/CSA approved models have AWG20 UL1015 approved wiring.

AV 0.75f Lead wire (red)*

AV 0.75f Lead wire (blue)*

AV 0.75f Lead wire (black)*

2.8

(5) 10.3

22.2±0.1

300 mm type 1,000 mm type

L300 ±10 mm 1,000 ±30 mm

Pin Plunger Models

D2VW-01-1HS

D2VW-5-1HS

t=0.5

Three, solder terminals

1.3 dia. hole2.4 dia. hole

8.4

5.2

1.2

4.810.3

20.2±0.25

2.5 dia.

2.5

5.2

41.4

22.2±0.1

10.3±0.1

15.9

2.8

3.1+0.13

–0.03

3.1+0.13

–0.03 dia. holes

0.5

3.2±0.1 dia.

2.8

OF max 200 gf

RF min. 30 gf

PT max. 1.2 mm

OT min. 1.0 mm

MD max. 0.4 mm

OP 14.7 ±0.4 mm

Short Hinge Lever Models

D2VW-01L1A-1MS

D2VW-5L1A-1MS

10.3

54.3

15.9

*Stainless-steel lever

t=0.5*

24.3±0.8

OF max 200 gf

RF min. 20 gf

PT max. 1.6 mm

OT min. 0.8 mm

MD max. 0.5 mm

OP 15.2 ±0.5 mm

Hinge Lever Models

D2VW-01L1-1MS

D2VW-5L1-1MS

10.3

4.3

*Stainless-steel lever

t=0.5*

35.6±0.8

15.9

OF max 120 gf

RF min. 15 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 0.8 mm

OP 15.2 ±1.2 mm

Sealed Snap Action Switch D2VW 5

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

2. Omitted dimensions are the same as pin plunger type.

3. The operating characteristics are for operation in the A direction( )

Long Hinge Lever Models

D2VW-01L1B-1MS

D2VW-5L1B-1MS

10.3

4.3

15.9

*Stainless-steel lever

t=0.5*

59.4±0.8

AOF max 60 gf

RF min. 5gf

PT max. 9.0 mm

OT min. 3.2 mm

MD max. 2.0 mm

OP 15.2 ±2.6 mm

Simulated Roller Lever Models

D2VW-01L3-1MS

D2VW-5L3-1MS 54.3

10.3

3.5R t=0.5*

32.6±0.8

*Stainless-steel lever

15.9

t=0.5*

OF max 120 gf

RF min. 15 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 0.8 mm

OP 18.7 ±1.2 mm

Short Hinge Roller Lever Models

D2VW-01L2A-1MS

D2VW-5L2A-1MS

24.3±0.8

20.1±0.8

t=0.5*

4.8 dia. 4.8 **

7.2

10.3

15.9

*Stainless-steel lever

**Oil-less polyacetal resin roller

OF max 230 gf

RF min. 20 gf

PT max. 1.6 mm

OT min. 0.8 mm

MD max. 0.5 mm

OP 20.7 ±0.6 mm

Hinge Roller Lever Models

D2VW-01L2-1MS

D2VW-5L2-1MS 4.8 dia. 4.8 **

7.2

10.3

*Stainless-steel lever

**Oil-less polyacetal resin roller

t=0.5*

34±0.8

15.9

AOF max 120 gf

RF min. 15 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 0.8 mm

OP 20.7 ±1.2 mm

6Sealed Snap Action Switch D2VW

Precautions

Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,

“Snap Action Switches, Technical Information” for correct use.

■Correct Use

Operations

Make sure that the switching object is perfectly separated from the

actuator when the switch is not operated and the actuator is pressed

appropriately by the switching object when the switch is operated.

The switch should be set so that its stroke will be within the rated OT

when the switch is operated.

With the pin plunger models, set the switch so that the plunger can

be actuated from directly above. Since the plunger is covered with a

rubber cap, applying a force from lateral directions may cause

damage to the plunger or reduction in the sealing capability.

Handling

Handle the switch carefully so as not to break the sealing rubber of

the plunger.

Using Microloads

Using a model for ordinary loads to switch microloads may result in

faulty operation. Instead, use the models that are designed for

microloads and that operate in the following range;

However, even when using microload models within the operating

range shown above, if inrush current or inductive voltage spikes

occur when the contact is opened or closed, then contact wear may

increase and so decrease the service life. Therefore, insert a contact

protection circuit where necessary.

Soldering - Connecting to Solder Terminals

When soldering the lead wire to the terminal, first insert the lead wire

conductor through the terminal hole and then conduct soldering.

Complete the soldering at the iron tip temperature between 350 to

400 C within 3 seconds, and do not apply any external force for 1

minute after soldering. Soldering at an excessively high temperature

or soldering for more than 3 seconds may deteriorate the character-

istics of the switch.

Mounting

Use M3 mounting screws with plane washers or spring washers to

securely mount the switch.

Tighten the screws to a torque of 0.39 to 0.59 N·m(4to6kgf·cm)

■Cautions

Degree of Protection

Do not use the Switch underwater.

The switch was tested and found to satisfy the conditions necessary

to meet the following standards. However, the test only checks for

water intrusion after immersion for a specified time period, not for

switching and operation underwater.

The switch is tested and conforms to JIS C0920 (Degrees of protec-

tion provided by enclosures of electrical apparatus) and IEC60529

(Degrees of protection provided by enclosures).

Note: The object to be tested is submerged at a depth of 1 meter for

30 minutes, then checked for water intrusion.

Protection Against Chemicals

Prevent the switch from coming into contact with oil and chemicals.

Otherwise, damage to or deterioration of the switch materials may

occur.

Correct

Incorrect

Operating range

for micro load

models D2VW-01

Operating

range for

general-load

models

D2VW-05

Current (mA)

Voltage (V)

Inoperable

range

110 100 1,000

0.16mA 100mA

100mA 160mA

26mA

1mA

Sealed Snap Action Switch D2VW 7

MEMO

8Sealed Snap Action Switch D2VW

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. C095-E-05 Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

847-882-2288

09/14 (11/10) Specifications subject to change without notice

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.