Specification():RT-375 ISSUE()7 (Japanese) Tyco Electronics Corporation 305 Constitutional Drive Menlo Park, CA 94025 USA 213-8535 3-5-8 044-844-8111 Specification This Issue: Date: Replaces: : : : RT-375 Issue 7 4 Feb 2004 Issue 6 RT-375 7 2004 2 4 2004 2 12 RT-375 Issue 7 THERMOFIT(R) RT-375 TUBING 1. 150 2. 2.1 O-S-1926 Sodium Chloride, Technical MIL-H-5606 Hydraulic Fluid, Petroleum Base, Aircraft, Missile and Ordnance MIL-T-83133 Turbine Fuel, Aviation, Grades JP-8 MIL-L-7808 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base MIL-A-8243 Anti-icing and Deicing - Defrosting Fluid MIL-L-23699 Lubricating Oil, Aircraft Turbine Engines, Synthetic Base 1 of 7 Specification():RT-375 ISSUE()7 (Japanese) 2.2 American Society for Testing and Materials (ASTM) D 2671 Standard Methods of Testing Heat-Shrinkable Tubing for Electrical Use (ASTM the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsylvania 19103 ASTM http://www.astm.org) International Organization for Standardization (ISO) ISO 846 Plastics - Evaluation of the action of Microorganisms (ISOInternational Organization for Standardization, 1, rue de Varembe, CH-1211 Geneva 20, Switzerland ISO http://www.iso.ch/iso/en/ISOOnline.frontpage) SAE International AMS-DTL-23053 Insulating Sleeving, Electrical, Heat Shrinkable, General Specification for (SAESAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001 SAE http://www.sae.org) 3. 3.1 3.2 Table 3 4. 4.1 4.1.1 2 of 7 Specification():RT-375 ISSUE()7 (Japanese) 4.1.2 4.2 4.2.1 15m 3/64 1/4 3/8 2 4.2.2 5m 4.2.3 4.3 20053 233505%RH3 3050m 3 of 7 Specification():RT-375 ISSUE()7 (Japanese) 4.3.1 1/4300mm31/4 6mm300mm3 4.3-55 1010% 3602 4.4 5. 5.1 5.2 5.3 4 of 7 Specification():RT-375 ISSUE()7 (Japanese) TABLE 1 (in.) mm. (in.) mm. (in.) mm. (in.) mm. (in.) mm. 3/64 .046 1.17 .023 0.58 .008 0.20 .012 0.30 .010 0.25 1/16 .063 1.60 .031 0.79 .008 0.20 .012 0.30 .010 0.25 3/32 .093 2.36 .046 1.17 .008 0.20 .012 0.30 .010 0.25 1/8 .125 3.17 .062 1.57 .008 0.20 .012 0.30 .010 0.25 3/16 .187 4.74 .093 2.36 .008 0.20 .012 0.30 .010 0.25 1/4 .250 6.35 .125 3.17 .009 0.23 .015 0.38 .012 0.30 3/8 .375 9.50 .187 4.74 .009 0.23 .015 0.38 .012 0.30 1/2 .500 12.70 .250 6.35 .009 0.23 .015 0.38 .012 0.30 3/4 .750 19.05 .375 9.50 .014 0.36 .020 0.51 .017 0.43 1 1.000 25.40 .500 12.70 .016 0.41 .022 0.56 .019 0.48 1-1/2 1.500 38.1 .750 19.05 .017 0.43 .023 0.58 .020 0.51 2 2.000 50.80 1.000 25.40 .017 0.43 .023 0.58 .020 0.51 TABLE 2 (in.) mm. 3/64 1/4 5/16 0.002 7.9 0.05 3/8 1/2 3/8 0.003 9.5 0.08 3/4 2 7/16 0.004 11.1 0.10 5 of 7 Specification():RT-375 ISSUE()7 (Japanese) TABLE 3 mm (Inches ) Table 1 ASTM D 2671 % +0, -10 1 MPa (psi) 24.1 (3500) ASTM D 2671 % 300 2 ASTM D 2671 3/641 % 70 1-1/22 % 60 MPa (psi) 172 (2.5 x 104) ASTM D 2671 --- 1.90 ASTM D 2671 --- Section 4.3.1 --- Table 3 -55 24 250 34 ASTM D 2671 ASTM D 2671 225 3336 r: % 100 --- AMS-DTL-23053 V/mm 15,760 (400) ASTM D 2671 200 324 (volts/mil) 3 -cm 1011 ASTM D 2671 --- ASTM D 2671 160 216 Procedure A --- 160 216 Procedure B --- 1 ASTM D 2671 25% 6 of 7 ASTM D 2671 Procedure C Specification():RT-375 ISSUE()7 (Japanese) TABLE 3 ) ISO 846 Method : B MPa (psi) 24.1 (3500) % 300 2 V/mm 15,760 (400) ASTM D 2671 (Volts/ mil) ASTM D 2671 % 0.5 ASTM D 2671 --- --- ASTM D 2671 23 324 50 324 4 JP-8 (MIL-T-83133) (MIL-H-5606) (MIL-L-23699) (MIL-L-7808) 5% O-S-1926 (MIL-A-8243) MPa (psi) 13.8 (2000) % 250 V/mm 15,760 (400) (volts/mil) 1: 200 33. 2: 25.4mm25.4mm505mm 3: 175 2 10 4: . 7 of 7