TN1215, TS1220 TYN612, TYN812, TYN1012 Sensitive and standard 12 A SCRs Features A On-state rms current, IT(RMS) 12 A Repetitive peak off-state voltage, VDRM/VRRM 600 to 1000 V A K A G G K DPAK TN1215-xxxB TS1220-xxxB A Triggering gate current, IGT 0.2 to 15 mA Description A K A G D2PAK TN1215-xxxG TS1220-xxxG Available either in sensitive (TS1220) or standard (TN1215 / TYNx12) gate triggering levels, the 12 A SCR series is suitable to fit all modes of control, found in applications such as overvoltage crowbar protection, motor control circuits in power tools and kitchen aids, inrush current limiting circuits, capacitive discharge ignition and voltage regulation circuits. K K G IPAK TN1215-xxxH TS1220-xxxH A Available in through-hole or surface-mount packages, they provide an optimized performance in a limited space area. A A A G TO-220AB TYNx12RG TYNx12TRG G A K TO-220AB TS1220-xxxT Table 1. Device summary Voltage (xxx) VDRM/VRRM Order code 600 V 700 V 800 V 1000 V Sensitivity IGT Package TN1215-xxxB X X 15 mA DPAK TN1215-xxxG X X 15 mA D2PAK TN1215-xxxH X X 15 mA IPAK TS1220-xxxB X 0.2 mA DPAK TS1220-xxxH X 0.2 mA IPAK TS1220-xxxT X 0.2 mA TO-220AB TYNx12RG X X X 15 mA TO-220AB TYNx12TRG X X X 5 mA TO-220AB September 2011 X Doc ID 7475 Rev 7 1/13 www.st.com 13 Characteristics TN1215, TS1220, TYN612, TYN812, TYN1012 1 Characteristics Table 2. Absolute ratings (limiting values) Value Symbol IT(RMS) Parameter TN1215-G TN1215-B/-H TYNx12 TS1220-B/-H/T Unit RMS on-state current (180 Conduction angle) Tc = 105 C 12 A IT(AV) Average on-state current (180 Conduction angle) Tc = 105 C 8 A ITSM Non repetitive surge peak on-state current I t tp = 8.3 ms tp = 10 ms Tj = 25 C 145 115 140 110 98 60 A It Value for fusing tp = 10 ms Tj = 25 C dI/dt Critical rate of rise of on-state current IG = 2 x IGT, tr 100 ns F = 60 Hz Tj = 125 C 50 A/s IGM Peak gate current tp = 20 s Tj = 125 C 4 A Tj = 125 C 1 W PG(AV) Average gate power dissipation A2S Tstg Tj Storage junction temperature range Operating junction temperature range - 40 to + 150 - 40 to + 125 C VRGM Maximum peak reverse gate voltage (for TN1215 and TYNx12 only) 5 V Table 3. Sensitive electrical characteristics (Tj = 25 C, unless otherwise specified) Symbol IGT VGT Test conditions VD = 12 V, RL = 140 TS1220 Unit MAX. 200 A MAX. 0.8 V MIN. 0.1 V VGD VD = VDRM, RL = 3.3 k, RGK = 220 VRG IRG = 10 A MIN. 8 V IH IT = 50 mA, RGK = 1 k MAX. 5 mA IL IG = 1 mA, RGK = 1 k MAX. 6 mA Tj = 125 C dV/dt VD = 65 % VDRM, RGK = 220 Tj = 125 C MIN. 5 V/s VTM ITM = 24 A, tp = 380 s Tj = 25 C MAX. 1.6 V Vt0 Threshold voltage Tj = 125 C MAX. 0.85 V Rd Dynamic resistance Tj = 125 C MAX. 30 m 5 A 2 mA IDRM IRRM 2/13 VDRM = VRRM, RGK = 220 Tj = 25 C Tj = 125 C Doc ID 7475 Rev 7 MAX. TN1215, TS1220, TYN612, TYN812, TYN1012 Table 4. Characteristics Standard electrical characteristics (Tj = 25 C, unless otherwise specified) TN1215 Symbol TYN Test conditions Unit B/H IGT VGT VGD VD = VDRM RL = 3.3 k IH IT = 500 mA Gate open IL IG = 1.2 IGT dV/dt VD = 67 % VDRM VTM ITM = 24 A Vt0 Rd IDRM IRRM Tj = 125 C Gate open x12 MIN. 2 0.5 2 MAX. 15 5 15 MAX. 1.3 V MIN. 0.2 V MAX. 40 30 15 30 mA MAX. 80 60 30 60 mA 40 200 V/s Tj =125 C MIN. Tj = 25 C MAX. 1.6 V Threshold voltage Tj = 125 C MAX. 0.85 V Dynamic resistance Tj = 125 C MAX. 30 m 5 A 2 mA tp = 380 s Tj = 25 C VDRM = VRRM Table 5. x12T mA RL = 33 VD = 12 V G 200 MAX. Tj = 125 C Thermal resistance Symbol Parameter Junction to case (DC) Rth(j-c) (1) S = 0.5 cm S(1) = 1 cm Value Unit 1.3 C/W DPAK 70 D2PAK 45 IPAK 100 TO-220AB 60 C/W Junction to ambient (DC) Rth(j-a) 1. S = Copper surface under tab Figure 1. Maximum average power dissipation versus average on-state current Figure 2. P(W) Average and DC on-state current versus case temperature IT(AV)(A) 12 14 11 D.C. = 180 12 10 9 10 8 = 180 7 8 6 6 5 4 3 4 360 2 2 1 IT(AV)(A) 0 0 1 2 3 4 Tcase(C) 5 6 7 0 8 9 0 Doc ID 7475 Rev 7 25 50 75 100 125 3/13 Characteristics Figure 3. TN1215, TS1220, TYN612, TYN812, TYN1012 Average and D.C. on-state current versus ambient temperature (DPAK) Figure 4. IT(AV)(A) Relative variation of thermal impedance junction to case versus pulse duration K=[Zth(j-c)/Rth(j-c)] 3.0 1.0 Device mounted on FR4 with recommended pad layout 2.5 D.C. 2.0 0.5 D2PAK 1.5 = 180 DPAK 1.0 0.2 0.5 tp(s) Tamb(C) 0.0 0 25 Figure 5. 50 75 100 125 Relative variation of thermal impedance junction to ambient versus pulse duration (DPAK) 0.1 1E-3 1E-2 Figure 6. K=[Zth(j-a)/Rth(j-a)] 1E-1 1E+0 Relative variation of gate trigger and holding current versus junction temperature for TS1220 series IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25C] 1.00 2.0 Device mounted on FR4 with recommended pad layout 1.8 1.6 IGT DPAK 1.4 1.2 D2PAK 0.10 1.0 TO-220AB / IPAK IH & IL RGK = 1k 0.8 0.6 0.4 0.2 tp(s) 1E-2 1E-1 Figure 7. Tj(C) 0.0 0.01 1E+0 1E+1 1E+2 -40 5E+2 Relative variation of gate trigger Figure 8. and holding current versus junction temperature -20 0 20 60 80 100 120 140 Relative variation of holding current versus gate-cathode resistance (typical values) IH[RGK] / IH[RGK=1k] IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25C] 5.0 2.4 Tj = 25C TS1220 Series 4.5 2.2 TN1215 and TYNx12 Series 2.0 4.0 IGT 1.8 3.5 1.6 3.0 1.4 1.2 2.5 1.0 2.0 IH & IL 0.8 0.6 1.5 0.4 1.0 0.2 Tj(C) 0.5 40 0.0 1E-2 RGK(k) 0.0 -40 4/13 40 -20 0 20 60 80 100 120 140 Doc ID 7475 Rev 7 1E-1 1E+0 1E+1 TN1215, TS1220, TYN612, TYN812, TYN1012 Figure 9. Characteristics Relative variation of dV/dt immunity Figure 10. Relative variation of dV/dt immunity versus gate-cathode resistance versus gate-cathode capacitance (typical values) for TS12 series (typical values) for TS12 series dV/dt[CGK] / dV/dt[RGK=220] dV/dt[RGK] / dV/dt[RGK=220] 4.0 10.0 Tj = 125C VD = 0.67 x VDRM VD = 0.67 x VDRM Tj = 125C RGK = 220 3.5 3.0 2.5 2.0 1.0 1.5 1.0 0.5 RGK(k) 0.1 CGK(nF) 0.0 0 200 400 600 800 1000 1200 0 25 50 75 100 125 150 Figure 11. Surge peak on-state current versus Figure 12. Non-repetitive surge peak on-state number of cycles current and corresponding values of It versus sinusoidal pulse width ITSM(A) 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 ITSM(A), I2t (A2s) 2000 Tj initial = 25C ITSM 1000 tp=10ms TN12 / TYN12 TN12 / TYN12 One cycle Non repetitive Tj initial=25C TS12 dI/dt limitation TS12 TN12 / TYN12 100 I2t TS12 Repetitive TC=105C Number of cycles tp(ms) 10 1 10 100 1000 0.01 0.10 1.00 10.00 Figure 13. On-state characteristics (maximum Figure 14. Thermal resistance junction to values) ambient versus copper surface under tab (DPAK and D2PAK) Rth(j-a)(C/W) ITM(A) 100 200 Tj max.: Vt0=0.85V Rd=30m 100 Epoxy printed circuit board FR4 copper thickness = 35 m 80 60 Tj=max DPAK 10 40 Tj=25C D2PAK 20 VTM(V) S(cm) 1 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 Doc ID 7475 Rev 7 2 4 6 8 10 12 14 16 18 20 5/13 Ordering information scheme 2 TN1215, TS1220, TYN612, TYN812, TYN1012 Ordering information scheme Figure 15. TN1215 series TN 12 15 - 600 B (-TR) Standard SCR series Current 12 = 12 A Sensitivity 15 = 15 mA Voltage 600 = 600 V 800 = 800 V Package B = DPAK G = D2PAK H = IPAK Packing mode Blank = Tube -TR = Tape and reel (DPAK and D2PAK) Figure 16. TS1220 series TS 12 20 - 600 B (-TR) Sensitive SCR series Current 12 = 12 A Sensitivity 20 = 200 A Voltage 600 = 600 V 700 = 700 V Package B = DPAK H = IPAK T = TO-220AB Packing mode Blank = Tube -TR = Tape and reel Figure 17. TYNx12 series TYN Standard SCR series Voltage 6 = 600 V 8 = 800 V 10 = 1000 V Current 12 = 12 A Sensitivity Blank = 15 mA T = 5 mA Packing mode RG = Tube 6/13 Doc ID 7475 Rev 7 6 12 T RG TN1215, TS1220, TYN612, TYN812, TYN1012 3 Package information Package information Epoxy meets UL94, V0 Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Table 6. TO-220AB dimensions (devices TYNx12RG and TYNx12TRG) Dimensions Ref. Millimeters Min. A OI 15.20 a1 C B b2 L F A I4 Typ. Max. Inches Min. Typ. 15.90 0.598 3.75 Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 2.40 2.70 0.094 0.106 F 6.20 6.60 0.244 0.259 OI 3.75 3.85 0.147 0.151 I4 15.80 16.40 16.80 0.622 0.646 0.661 L 2.65 2.95 0.104 0.116 l2 1.14 1.70 0.044 0.066 l3 1.14 1.70 0.044 0.066 l3 c2 a1 l2 a2 M b1 c1 e M Doc ID 7475 Rev 7 2.60 0.102 7/13 Package information Table 7. TN1215, TS1220, TYN612, TYN812, TYN1012 TO-220AB dimensions (device TS1220-xxxT) Dimensions Ref. Dia Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 F2 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 G1 2.40 2.70 0.094 0.106 H2 10 10.40 0.393 0.409 C L5 L7 L6 L2 F2 D L9 L4 L2 F M G1 Inches A H2 F1 Millimeters 16.4 typ. 0.645 typ. L4 13 14 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.20 6.60 0.244 0.259 L9 3.50 3.93 0.137 0.154 E G M Diam. 8/13 Doc ID 7475 Rev 7 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 TN1215, TS1220, TYN612, TYN812, TYN1012 Table 8. Package information IPAK dimensions Dimensions Ref. Millimeters Min. A E C2 B2 L Min. Typ. Max. 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A3 0.70 1.30 0.027 0.051 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 0.95 B5 D Max. A B3 L2 H Typ. Inches 0.037 0.30 0.035 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.019 0.023 D 6 6.20 0.236 0.244 E 6.40 6.60 0.252 0.260 B3 L1 B A1 V1 e B5 e G 2.28 0.090 C A3 G 4.40 H Doc ID 7475 Rev 7 4.60 0.173 16.10 0.181 0.634 L 9 9.40 0.354 0.370 L1 0.8 1.20 0.031 0.047 L2 0.80 V1 10 1 0.031 0.039 10 9/13 Package information Table 9. TN1215, TS1220, TYN612, TYN812, TYN1012 DPAK dimensions Dimensions Ref. E A B2 C2 L2 Millimeters Inches Min. Max. Min. Max. A 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.018 0.023 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.251 0.259 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.397 D R H L4 A1 B G R C A2 0.60 MIN. V2 L2 0.80 typ. L4 0.60 1.00 0.023 0.039 V2 0 8 0 8 Figure 18. DPAK footprint dimensions (in millimeters) 6.7 3 3 1.6 2.3 6.7 2.3 1.6 10/13 Doc ID 7475 Rev 7 0.031 typ. TN1215, TS1220, TYN612, TYN812, TYN1012 Table 10. Package information D2PAK dimensions Dimensions Ref. Millimeters Min. A E C2 L2 D L L3 Typ. Inches Max. Min. Typ. Max. A 4.30 4.60 0.169 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.25 C 0.45 0.60 0.017 0.024 C2 1.21 1.36 0.047 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.28 0.393 0.405 G 4.88 5.28 0.192 0.208 L 15.00 15.85 0.590 0.624 L2 1.27 1.40 0.050 0.055 L3 1.40 1.75 0.055 0.069 1.40 0.048 0.055 A1 B2 R C B G A2 2mm min. FLAT ZONE V2 R V2 0.40 0 0.016 8 0 8 Figure 19. D2PAK footprint dimensions (in millimeters) 16.90 10.30 5.08 1.30 8.90 Doc ID 7475 Rev 7 3.70 11/13 Ordering information 4 TN1215, TS1220, TYN612, TYN812, TYN1012 Ordering information Table 11. Ordering information Order code(1) Marking(1) Package Weight Base qty Delivery mode TN1215-x00B TN12 15x00 DPAK 0.3 g 75 Tube TN1215-x00B-TR TN12 15x00 DPAK 0.3 g 2500 Tape and reel 2 TN1215-x00G TN1215x00G D PAK 1.5 g 50 Tube TN1215-x00G-TR TN1215x00G D2PAK 1.5 g 1000 Tape and reel TN1215-x00H TN12 15x00 IPAK 0.3 g 75 Tube TS1220-x00B TS12 20x00 DPAK 0.3 g 75 Tube TS1220-x00B-TR TS12 20x00 DPAK 0.3 g 2500 Tape and reel TS1220-x00H TS12 20x00 IPAK 0.3 g 75 Tube TS1220-x00T TS1220600T TO-220AB 2.3 g 50 Tube TYNx12RG TYNx12 TO-220AB 2.3 g 50 Tube TYNx12TRG TYNx12T TO-220AB 2.3 g 50 Tube 1. x (6, 7, 8, 10) depends upon voltage 5 Revision history Table 12. 12/13 Document revision history Date Revision Changes Sep-2000 3 Last update. 25-Mar-2005 4 TO-220AB delivery mode changed from bulk to tube. 14-Oct-2005 5 Changed sensitivity values in Table 1 for TYNx12 (30 to 15 mA) and TYNx12T ( 15 to 5 mA). Added ECOPACK statement. 08-Mar-2007 6 Reformatted to current standard. Figure 15: TN1215 series product name corrected. Figure 16: TS1220 series product name corrected. 12-Oct-2009 7 Added TS1220-xxxT device. Doc ID 7475 Rev 7 TN1215, TS1220, TYN612, TYN812, TYN1012 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 7475 Rev 7 13/13