INTEGRATED CIRCUITS DATA SHEET TDA4851 Horizontal and vertical deflection controller for VGA/XGA and autosync monitors Preliminary specification File under Integrated Circuits, IC02 November 1992 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 FEATURES * DC-coupling to vertical power amplifier * VGA operation fully implemented including alignment-free vertical and E/W amplitude presettings * Internal supply voltage stabilization with excellent ripple rejection to ensure stable geometrical adjustments * 4th VGA mode easy applicable (XGA, Super VGA) * Autosync operation externally selectable GENERAL DESCRIPTION * Low jitter The TDA4851 is a monolithic integrated circuit for economical solutions in VGA/XGA and autosync monitors. The IC incorporates the complete horizontal and vertical small signal processing. VGA-dependent mode detection and settings are performed on chip. In conjunction with TDA4860/61/65, or TDA8351 (vertical output circuits) the ICs offer an extremely advanced system solution. * All adjustments DC-controllable * Alignment-free oscillators * Sync separators for video or horizontal and vertical TTL sync levels regardless of polarity * Horizontal oscillator with PLL1 for sync and PLL2 for flyback * Constant vertical and E/W amplitude in autosync operation QUICK REFERENCE DATA SYMBOL PARAMETER MIN. TYP. MAX. UNIT VP positive supply voltage (pin 1) 9.2 12 16 V IP supply current - 40 - mA Vi sync AC-coupled composite video signal with negative-going sync (peak-to-peak value, pin 9) - 1 - V sync slicing level - 120 - mV DC-coupled TTL-compatible horizontal sync signal (peak-to-peak value, pin 9) 1.7 - - V slicing level 1.2 1.4 1.6 V DC-coupled TTL-compatible vertical sync signal (peak-to-peak value, pin 10) 1.7 - - V slicing level 1.2 1.4 1.6 V Io V vertical differential output current (peak-to-peak value, pins 5 and 6) - 1 - mA Io H horizontal sink output current on pin 3 - - 60 mA Tamb operating ambient temperature range 0 - +70 C ORDERING INFORMATION PACKAGE EXTENDED TYPE NUMBER PINS TDA4851 20 PIN POSITION DIL Note 1. SOT146-1; 1996 November 26. November 1992 2 MATERIAL CODE plastic SOT146(1) This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... Philips Semiconductors 3 Horizontal and vertical deflection controller for VGA/XGA and autosync monitors November 1992 Preliminary specification TDA4851 Fig.1 Block diagram. Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 PINNING SYMBOL PIN DESCRIPTION VP 1 positive supply voltage FLB 2 horizontal flyback input HOR 3 horizontal output GND 4 ground (0 V) VERT1 5 vertical output 1; negative-going sawtooth VERT2 6 vertical output 2; positive-going sawtooth MODE 7 4th mode output and autosync input CLBL 8 clamping/blanking pulse output HVS 9 horizontal sync/video input VS 10 vertical sync input EW 11 E/W output (parabola to driver stage) CVA 12 capacitor for amplitude control RVA 13 vertical amplitude adjustment input REW 14 E/W amplitude adjustment input (parabola) RVOS 15 vertical oscillator resistor CVOS 16 vertical oscillator capacitor PLL1 17 PLL1 phase RHOS 18 horizontal oscillator resistor CHOS 19 horizontal oscillator capacitor PLL2 20 PLL2 phase Fig.2 Pin configuration. VGA mode detector. If pin 10 is not used, it must be connected to ground. The separated Vi sync signal from pin10, or the integrated composite sync signal from pin 9 (TTL or video) triggers directly the vertical oscillator. FUNCTIONAL DESCRIPTION Horizontal sync separator and polarity correction An AC-coupled video signal or a DC-coupled TTL sync signal (H only or composite sync) is input on pin 9. Video signals are clamped with top sync on 1.28 V, and are sliced at 1.4 V. This results in a fixed absolute slicing level of 120 mV related to top sync. DC-coupled TTL sync signals are also sliced at 1.4 V, however with the clamping circuit in current limitation. The polarity of the separated sync is detected by internal integration of the signal, then the polarity is corrected. The polarity information is fed to the VGA mode detector. The corrected sync is input signal for the vertical sync integrator and the PLL1 stage. VGA mode detector and mode output The three standard VGA modes and a 4th not fixed mode are decoded by the polarities of the horizontal and the vertical sync input signals. An external resistor (from VP to pin 7) is necessary to match this function. In all three VGA modes the correct amplitudes are activated. The presence of the 4th mode is indicated by a HIGH on pin 7. This signal can be used externally to switch any horizontal or vertical parameters. VGA mode detector input Vertical sync separator, polarity correction and vertical sync integrator For autosync operation the voltage on pin 7 must be externally forced to a level of < 50 mV. Vertical amplitude pre-settings for VGA are then inhibited. The delay time between vertical trigger pulse and the start of vertical deflection changes from 575 s to 300 s (575 s is DC-coupled vertical TTL sync signals may be applied to pin 10. They are sliced at 1.4 V. The polarity of the separated sync is detected by internal integration, then the polarity is corrected. The polarity information is fed to the November 1992 4 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 A certain amount of phase adjustment is possible by injecting a DC current from an external source into the PLL2 filter capacitor at pin 20. needed for VGA). The vertical amplitude then remains constant in a frequency range from 50 Hz up to 110 Hz. Clamping and V-blanking generator Horizontal driver A combined clamping and V-blanking pulse is available on pin 8 (suitable for the video pre-amplifier TDA4881). The lower level of 1.9 V is the blanking signal derived from the vertical blanking pulse from the internal vertical oscillator. Vertical blanking equals the delay between vertical sync and start of vertical scan. By this, an optimum blanking is achieved for VGA/XGA and autosync operation (selectable via pin 7). The upper level of 5.4 V is the horizontal clamping pulse with an internally fixed pulse width of 0.8 s. A monoflop, which is triggered by the trailing edge of the horizontal sync pulse, generates this pulse. If composite sync is applied, one clamping pulse per H-period is generated during V-sync. The phase of the clamping pulse may change during V-sync (see Fig.8). This open-collector output stage (pin 3) can directly drive an external driver transistor. The saturation voltage is less than 300 mV at 20 mA. To protect the line deflection transistor, the horizontal output stage does not conduct for VP < 6.4 V (pin 1). Vertical oscillator and amplitude control This stage is designed for fast stabilization of the vertical amplitude after changes in sync conditions. The free-running frequency f0 is determined by the values of RVOS and CVOS. The recommended values should be altered marginally only to preserve the excellent linearity and noise performance. The vertical drive currents I5 and I6 are in relation to the value of RVOS. Therefore, the oscillator frequency must be determined only by CVOS on pin 16. 1 f 0 = ----------------------------------------------------10.8 x R VOS x C VOS PLL1 phase detector The phase detector is a standard type using switched current sources. The middle of the sync is compared with a fixed point of the oscillator sawtooth voltage. The PLL filter is connected to pin 17. If composite sync is applied, the disturbed control voltage is corrected during V-sync (see Fig.8). To achieve a stabilized amplitude the free-running frequency f0 (without adjustment) must be lower than the lowest occurring sync frequency. The following contributions can be assumed: Horizontal oscillator This oscillator is of the relaxation type and requires a fixed capacitor of 10 nF at pin 19. By changing the current into pin 18 the whole frequency range from 13 to 100 kHz can be covered. The current can be generated either by a frequency to voltage converter or by a resistor. A frequency adjustment may also be added if necessary. The PLL1 control voltage at pin 17 modulates via a buffer stage the oscillator thresholds. A high DC-loop gain ensures a stable phase relationship between horizontal sync and line flyback pulses. 10% spread of IC 3% spread of R (22 k) 1% spread of C (0.1 F) 5% 19% 50 Result: f 0 = ----------- Hz = 42 Hz 1.19 PLL2 phase detector (for 50 to 110 Hz application) This phase detector is similar to the PLL1 phase detector. Line flyback signals (pin 2) are compared with a fixed point of the oscillator sawtooth voltage. Delays in the horizontal deflection circuit are compensated by adjusting the phase relationship between horizontal sync and horizontal output pulses. November 1992 minimum frequency offset between f0 and the lowest trigger frequency 5 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors Table 1 TDA4851 VGA modes MODE H / V SYNC POLARITY FREQUENCY H (kHz) FREQUENCY V (Hz) NUMBER OF ACTIVE LINES MODE OUTPUT PIN 7 1 +/- 31.45 70 350 LOW 2 -/+ 31.45 70 400 LOW 3 -/- 31.45 60 480 LOW 4 +/+ fixed by external circuitry - - HIGH autosync */* fixed by external circuitry - - forced to GND LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL PARAMETER MIN. MAX. UNIT VP supply voltage (pin 1) -0.5 16 V V3,7 voltage on pins 3 and 7 -0.5 16 V V8 voltage on pin 8 -0.5 7 V Vn voltage on pins 5, 6, 9, 10, 13, 14 and 18 -0.5 6.5 V I2 current on pin 2 - 10 mA I3 current on pin 3 - 100 mA I7 current on pin 7 - 20 mA I8 current on pin 8 - -10 mA Tstg storage temperature range -55 +150 C Tamb operating ambient temperature range 0 70 C Tj maximum junction temperature 0 +150 C VESD electrostatic handling for all pins (note 1) - 400 V Note to the Limiting Values 1. Equivalent to discharging a 200 pF capacitor through a 0 series resistor. THERMAL RESISTANCE SYMBOL Rth j-a November 1992 PARAMETER THERMAL RESISTANCE from junction to ambient in free air 65 K/W 6 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 CHARACTERISTICS VP = 12 V; Tamb = +25 C; measurements taken in Fig.3 unless otherwise specified SYMBOL PARAMETER VP positive supply voltage (pin 1) IP supply current CONDITIONS MIN. TYP. MAX. UNIT 9.2 12 16 V I18 = -1.05 mA - 36 44 mA I18 = -3.388 mA - 40 49 mA Internal reference voltage Vref internal reference voltage 6.0 6.25 6.5 V TC temperature coefficient Tamb = +20 to +100 C - - 90 10-6/K PSRR power supply ripple rejection f = 1 kHz sinewave 60 75 - dB f = 1 MHz sinewave 25 35 - dB VP supply voltage (pin 1) to ensure all internal reference voltages 9.2 - 16 V - 300 - mV 1.1 1.28 1.5 V Composite sync input (AC-coupled) V10 = 5 V Vi sync sync on green sync amplitude of video input signal (pin 9) top sync clamping level slicing level above top sync level RS = 50 90 120 150 mV RS allowed source resistance for 7% duty factor Vi sync > 200 mV - - 1.5 k r9 differential input resistance during sync - 80 - I9 charging current of coupling capacitor V9 > 1.5 V 1.3 2 3 A tint vertical sync integration time to generate vertical trigger pulse fH = 31 kHz; I18 = -1.050 mA 7 10 13 s fH = 64 kHz; I18 = -2.169 mA 3.5 5 6.5 s fH = 100 kHz; I18 = -3.388 mA 2.5 3.4 4.5 s sync input signal (peak-to-peak value, pin 9) 1.7 - - V slicing level 1.2 1.4 1.6 V tp minimum pulse width 700 - - ns tr, tf rise time and fall time 10 - 500 ns I9 input current V9 = 0.8 V - - -200 A V9 = 5.5 V - - 10 A Horizontal sync input (DC-coupled, TTL-compatible) Vi sync Automatic horizontal polarity switch H-sync on pin 9 tp H/tH horizontal sync pulse width related to tH (duty factor for automatic polarity correction) - - 30 % tp delay time for changing sync polarity 0.3 - 1.8 ms November 1992 7 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors SYMBOL PARAMETER Vertical sync input (DC-coupled, TTL-compatible) Vi sync CONDITIONS TDA4851 MIN. TYP. MAX. UNIT V-sync on pin 10 sync input signal (peak-to-peak value, pin 10) 1.7 - - V slicing level 1.2 1.4 1.6 V - - 10 A - - 300 s 0.275 0.33 V I10 input current tp V maximum vertical sync pulse width for automatic vertical polarity switch 0 < V10 < 5.5 V Horizontal mode detector output VGA mode V7 output saturation voltage LOW (for Modes 1, 2 and 3) I7 = 6 mA - output voltage HIGH mode 4 - - VP V I7 load current range to force VGA mode-dependent vertical and parabola amplitudes modes 1, 2 and 3 2 - 6 mA output current mode 4 - 0 - mA 0 - 50 mV - - 0.9 V VGA / autosync mode switch V7 input voltage LOW to force autosync mode Horizontal clamping / blanking generator output V8 I8 Fig.6 output voltage LOW blanking output voltage internal V blanking 1.6 1.9 2.2 V clamping output voltage H-sync on pin 9 5.15 5.4 5.65 V internal sink current for all output levels H and V scanning 2.3 2.9 3.5 mA external load current - - -3.0 mA t8 clamping pulse start with end of H-sync tclp clamping pulse width S steepness of rise and fall times V8 = 3 V 0.6 0.8 1.0 s - 60 75 ns/V Vertical oscillator Vref = 6.25 V f0 vertical free-running frequency R15 = 22 k; C16 = 0.1 F - 42 - Hz fv nominal vertical sync range no f0 adjustment 50 - 110 Hz V15 voltage on pin 15 R15 = 22 k 2.8 3.0 3.2 V td delay between sync pulse and start of vertical scan measured on pin 8 500 575 650 s 240 300 360 s in VGA/XGA mode, activated by an external resistor on pin 7 in autosync mode V7 < 50 mV I12 control current for amplitude control - 200 - A C12 capacitor for amplitude control - - 0.18 F November 1992 8 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors SYMBOL PARAMETER Vertical differential output Io CONDITIONS TDA4851 MIN. TYP. MAX. UNIT Fig.7 differential output current between pins 5 and 6 (peak-to-peak value) mode 3; I13 > -135 A; R15 = 22 k 0.9 1.0 1.1 mA maximum offset-current error Io = 1 mA - - 2.5 % - - 1.5 % - 5.0 - V maximum linearity error Vertical amplitude adjustment (in percentage of output signal) V13 input voltage I13 adjustment current Io max (100%) -110 -120 -135 A Io min (typically 58%) - 0 - A Io/t VGA mode-dependent pre-settings activated by an external resistor on pin 7 Table 1; note 1 Mode 1 116.2 116.8 117.4 % Mode 2 101.6 102.2 102.8 % Mode 3 - 100 - % Mode 4 - 100 - % - 100 - % - 5.9 - V autosync operation (VGA operation disabled) V7 < 50 mV Horizontal comparator PLL1 V17 upper control voltage limitation - 5.1 - V Fig.6 - 0.083I18 - mA R18 = 2.4 k (pin 18); C19 = 10 nF (pin 19) - 31.45 - kHz deviation of centre frequency - - 3 % temperature coefficient 0 +200 +300 10-6/K H/tH relative holding/catching range 6 6.5 7.3 % I18 external oscillator current -0.5 - -4.3 mA V18 voltage at reference current input (pin 18) 2.35 2.5 2.65 V lower control voltage limitation I17 control current Horizontal oscillator fosc centre frequency Horizontal PLL2 Fig.6 V2 upper clamping level of flyback input I2 = 6 mA - 5.5 - V lower clamping level of flyback input I2 = -1 mA - -0.75 - V H-flyback slicing level - 3.0 - V td/tH delay between middle of sync and middle of H-flyback related to tH - 3.0 - % V20 upper control voltage limitation - 6.2 - V lower control voltage limitation - 4.8 - V I20 control current - 0.083I18 - A t/tH PLL2 control range related to tH 30 - - % November 1992 9 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors SYMBOL PARAMETER Horizontal output (open-collector) V3 output voltage LOW CONDITIONS TDA4851 MIN. TYP. MAX. UNIT Fig.6 I3 = 20 mA - - 0.3 V I3 = 60 mA - - 0.8 V 42 45 48 % tp/tH tH duty factor VP threshold to activate under voltage protection horizontal output off - 5.6 - V horizontal output on - 5.8 - V jitter of horizontal output f = 31 kHz - - 3.5 ns f = 64 kHz - - 1.9 ns f = 100 kHz - - 1.2 ns 1.05 1.2 1.35 V top output signal during flyback 4.2 4.5 4.8 V temperature coefficient of output signal - - 250 10-6/K - 5.0 - V 100% parabola -110 -120 -135 A typically 28% parabola - 0 - A tH E/W output note 2 V11 internally stabilized bottom output signal during mid-scan (pin 11) E/W amplitude adjustment (parabola) V14 input voltage (pin 14) I14 adjustment current Fig.7 Notes to the characteristics 1. Io/t relative to value of Mode 3. 2. Parabola amplitude tracks with mode-dependent vertical amplitude but not with vertical amplitude adjustment. Tracking can be achieved by a resistor from vertical amplitude potentiometer to pin 14. November 1992 10 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors APPLICATION INFORMATION Fig.3 Application circuit for 3-mode VGA (31.45 kHz). Fig.4 64 kHz application circuit. November 1992 11 TDA4851 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors Fig.5 31 to 64 kHz application including 4-mode VGA. Fig.6 Horizontal timing diagram. November 1992 12 TDA4851 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors Fig.7 Vertical and E/W timing diagram. November 1992 13 TDA4851 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... TDA4851 Fig.8 Pulse diagram for composite sync applications (showing reduced influence of V-sync on H-phase and drive pulses for F/V converters). Preliminary specification clamp pulses triggered by H-sync clamp pulses triggered by leading edge of V-trigger pulse clamp pulses triggered by horizontal oscillator during V-trigger pulse clamp pulses are generated internally control voltage of PLL1 is corrected during V-trigger pulse Philips Semiconductors 14 Horizontal and vertical deflection controller for VGA/XGA and autosync monitors November 1992 (1) (2) (3) (4) (5) This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... Philips Semiconductors 15 Horizontal and vertical deflection controller for VGA/XGA and autosync monitors November 1992 Preliminary specification TDA4851 Fig.9 Internal circuits. Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 PACKAGE OUTLINE DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 11 20 pin 1 index E 1 10 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c mm 4.2 0.51 3.2 1.73 1.30 0.53 0.38 0.36 0.23 26.92 26.54 inches 0.17 0.020 0.13 0.068 0.051 0.021 0.015 0.014 0.009 1.060 1.045 D e e1 L ME MH w Z (1) max. 6.40 6.22 2.54 7.62 3.60 3.05 8.25 7.80 10.0 8.3 0.254 2.0 0.25 0.24 0.10 0.30 0.14 0.12 0.32 0.31 0.39 0.33 0.01 0.078 (1) E (1) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT146-1 November 1992 REFERENCES IEC JEDEC EIAJ SC603 16 EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-05-24 Philips Semiconductors Preliminary specification Horizontal and vertical deflection controller for VGA/XGA and autosync monitors TDA4851 The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. November 1992 17