MIP2K30MS Silicon MOS FET type integrated circuit Features Package Built-in jitter function Built-in charge protection circuit Built-in overheating, loadshorting and overvoltage protection circuits Chargers (for DSC, etc.) AC adapter Code DIP7-A1 Pin Name 1. VDD 2. FB 3. CL 4. VCC Absolute Maximum Ratings Ta = 25C3C Marking Symbol: MIP2K3 Applications Parameter Symbol Rating Unit DRAIN voltage VD - 0.3 to +700 V VCC voltage VCC - 0.3 to +45 V VDD voltage VDD - 0.3 to +8 V Feedback voltage VFB - 0.3 to +8 V Feedback current IFB 500 mA CL pin voltage VCL - 0.3 to +8 V CL pin current ICL 150 mA Output peak current * IDP 1.5 A Channel temperature Tch 150 C Storage temperature Tstg -55 to +150 C 5. DRAIN 6. 7. SOURCE 8. SOURCE Note) *: The guarantee within the following pulse width. Leading edge blanking delay + Current limit delay ton(BLK) + td(OCL) Block Diagram VCC DRAIN VCC UV VDD CL Regulator VCC(ON) Constant current resource VCC(OV) Overheat protection Restart trigger Oscillator with Jitter ILIMIT variable circuit IN ICL_LOW VCL_OUT VDD VCC OVP MAXDC fosc(L) CLOCK FB Light load detection For intermittent Oscillation control S Q R Q S Q R Q VDD UV Gate driver Power MOSFET Blanking pulse generation circuit in on-state ILIMIT compensation Drain current for detection VCL Clamp circuit (ILIMIT setting) SOURCE Publication date: October 2010 Ver. AEF 1 MIP2K30MS Electrical Characteristics TC = 25C2C Parameter Symbol Conditions Min Typ Max Unit VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 90 100 110 kHz VCC = 15 V, VD = 5 V, IFB: Open, ICL < ICL1 9 12 15 kHz Control functions fosc Output frequency fosc(L) Jitter frequency deviation f VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 5.5 kHz Jitter frequency modulation rate fM VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 260 Hz MAXDC VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 45 47.5 50 % VDD voltage VDD VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 5.4 5.9 6.4 V UV lockout threshold voltage VUV VD = 5 V, IFB = 20 mA, ICL = 50 mA 4.6 5.1 5.6 V VCC(ON) VD = 5 V, IFB = 20 mA, ICL = 50 mA 5.9 6.9 7.9 V 10 11 12 V 24.6 41 57.4 mA Maximum duty cycle VCC start voltage VCC charge stop threshold voltage VCC1 VD = 40 V, FB: Open, CL: Open Feedback threshold voltage IFB1 ON OFF VCC = 15 V, VD = 5 V, ICL = 50 mA Feedback hysteresis current IFBHYS VCC = 15 V, VD = 5 V, ICL = 50 mA FB pin current at heavy load IFB0 ICC0 ICC VCC = 15 V, VD = 5 V, ICL = 50 mA 6 9.5 13 mA FB pin voltage VFB VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 0.7 1.0 1.3 V Supply current ICC VCC = 15 V, VD = 5 V, IFB = 20 mA, ICL = 50 mA 0.25 0.40 0.50 mA VCC = 15 V, VD = 5 V, IFB = IFB1 + 5 mA, ICL = 50 mA 0.26 0.36 0.46 mA 2 mA Supply current at light load ICC(OFF) Supply current at heavy load ICC0 VCC = 15 V, VD = 5 V, IFB: Open, ICL = 50 mA 0.45 0.60 0.75 mA Ich1 VDD = 0 V, VD = 40 V, FB: Open, CL: Open -7.5 -5.5 -3.5 mA Ich2 VDD = 4 V, VD = 40 V, FB: Open, CL: Open -3.0 -2.0 -1.0 mA CL pin voltage VCL VCC = 15 V, VD = 5 V, FB: Open, ICL = ICL1 2.0 2.3 2.6 V Dropped fosc CL pin current *2 ICL1 fosc fosc(L) VCC = 15 V, VD = 5 V, FB: Open 16.5 22 27.5 mA ICLHYS VCC = 15 V, VD = 5 V, FB: Open VDD charging current CL pin hysteresis current *2 2 Ver. AEF 1.5 mA MIP2K30MS Electrical Characteristics (continued) TC = 25C2C Parameter Symbol Conditions Min Typ Max Unit 0.45 0.50 0.55 A Circuit protections Self protection current limit *1, 3 ILIMIT VCC = 15 V, FB: Open, ICL = 50 mA, DUTY = 30% ILIMIT modified coefficient *1, 3 R_slope VCC = 15 V, FB: Open, ICL = 50 mA Minimum ILIMIT ILIMITmin 40 mA/ms Ton = 3 ms, VCC = 15 V, FB: Open, ICL = 0 mA 52 115 178 mA Drain current at light load ID(OFF) Ton = 3 ms, VCC = 15 V, IFB = IFB1 + IFBHYS, ICL = 50 mA 45 110 165 mA Leading edge blanking delay ton(BLK) VCC = 15 V, FB: Open, ICL = 50 mA 230 290 350 ns Current limit delay td(OCL) 100 150 200 ns 21 23.5 26 V TOTP 130 140 150 C Power up reset threshold voltage VDDreset 1.8 2.6 3.5 V ON state resistance RDS(ON) ID = 100 mA 10 13 W 10 20 mA Over voltage protection Thermal shutdown temperature VCC(OV) VD = 5 V, FB: Open, ICL = 50 mA Output OFF state current IDSS VCC = 26 V, VD = 650 V, FB: Open, CL: Open Breakdown voltage VDSS VCC = 26 V, ID = 100 mA, FB: Open, CL: Open 700 V Rise time *4 tr VCC = 15 V, VD = 5 V, FB: Open, ICL = 50 mA 100 ns Fall time *4 tf VCC = 15 V, VD = 5 V, FB: Open, ICL = 50 mA 25 ns VD(MIN) VCC: Open, FB: Open, CL: Open Supply voltage characteristics Drain supply voltage 50 V Note) 1. Measurement circuit Ver. AEF 3 MIP2K30MS Electrical Characteristics (continued) TC = 25C2C 2. *1: ILIMIT vs. ICL Typical characteristic *2: fosc vs. ICL Typical characteristic *3: ILIMIT Measurement *4: tr, tf Measurement 4 Ver. AEF MIP2K30MS Frequency jitter function By frequency jitter function, frequency jitter variation(f) changes periodically, by frequency of frequency jitter modulation factor (fM) as shown below. fosc = 100 kHz (typ.), f = 5.5 kHz (typ.), fM = 260 Hz (typ.) Adapter circuit sample (MIP2K4) Electric characteristics (MIP2K4Worldwide input, 8.3V/1.5A output) Ver. AEF 5 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for general applications (such as office equipment, communications equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book. Consult our sales staff in advance for information on the following applications: Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with your using the products described in this book for any special application, unless our company agrees to your using the products in this book for any special application. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. Precautions on the Sales of IPDs 1) The sale and/or the export of IPD products to customers located in certain countries is restricted by the Agreement made and executed by and between Power Integrations, Inc. and Panasonic Corporation. For details, refer to the following Attached table "IPD availability by customer." 2) IPD products purchased from our company, or its authorized agents, hereinafter referred to as our company, shall be used only for production purposes by those parties who have duly purchased IPD products. Those who have purchased IPD products shall not use such IPD products in unmodified form for re-sale, loan, or sample shipment for evaluation purposes to any other parties. 3) If a party who has duly purchased IPD products subcontracts its production to any other parties, including its subsidiaries or any other third parties inside and/or out of Japan, and the IPD products are consigned to such subcontracting parties thereat, such party is obligated to monitor and control the quantity of IPD products to prevent any of the aforementioned re-sale, loan or sample shipments from taking place. 4) In the event that any actual or threatened breach or violation of any of the above mentioned 2) or 3) has occurred or is about to occur, our company will hold all shipments of IPD products and may request the customer to disclose necessary documentation describing the status of our end-users and/or distribution channels. Note) The products of MIP50**, MIP51**, and MIP7** are excluded from above-mentioned precautions, 1) to 3). Attached table "IPD availability by customer" Companies/areas to which products can be sold Parts No. Companies/areas to which products cannot be sold * Japanese companies in Japan * Companies in European and American countries * Japanese companies in Asia (50% or more owned) * Asian companies in Asia * Other local companies MIP01** MIP2** MIP9A** MIP02** MIP3** MIP9L** MIP00** MIP55** MIP816/826 MIP52** MIP56** MIP9E** * Japanese companies in Japan * Companies in European MIP53** * Japanese companies in Asia and American countries MIP803/804 (50% or more owned) * Other local companies * Asian companies in Asia MIP50** MIP51** MIP7** MIP1** MIP4** Note) For details, contact our sales division. 20130322 * No restrictions in terms of contract * No restrictions in terms of contract Application * For power supply * For DC-DC converter * For power supply * For EL driver * For LED lighting driver * For lamp driver/ car electronics accessories