MIP2K30MS - Panasonic - Datasheet.Live

Publication date: October 2010 Ver. AEF 1

MIP2K30MS

Silicon MOS FET type integrated circuit

 Features

 Built-in jitter function

 Built-in charge protection circuit

Built-in overheating, loadshorting and overvoltage protection circuits

 Applications

 Chargers (for DSC, etc.)

 AC adapter

 Absolute Maximum Ratings Ta = 25°C±3°C

Parameter Symbol Rating Unit

DRAIN voltage VD - 0.3 to +700 V

VCC voltage VCC - 0.3 to +45 V

VDD voltage VDD - 0.3 to +8V

Feedback voltage VFB - 0.3 to +8V

Feedback current IFB 500 mA

CL pin voltage VCL - 0.3 to +8V

CL pin current ICL 150 mA

Output peak current *IDP 1.5 A

Channel temperature Tch 150 °C

Storage temperature Tstg -55 to +150 °C

Note) *: The guarantee within the following pulse width.

Leading edge blanking delay + Current limit delay ton(BLK) + td(OCL)

 Block Diagram

Drain current

for detection

Blanking pulse

generation

circuit in on-state

SOURCE

Power

MOSFET

Gate driver

DRAIN

Regulator

Restart

trigger

Constant

current resource

ILIMIT

compensation

Overheat

protection

Light load detection

For intermittent

Oscillation control

Oscillator with Jitter

MAXDC

CLOCK

fosc(L)

VCC

VDD

VCC UV

VCC(ON)

VCC OVP

VCC(OV)

ILIMIT

variable circuit

ICL_LOW

VCL_OUT

VCL

Clamp circuit

(ILIMIT setting)

VDD UV

VDD

 Package

Code

DIP7-A1

Pin Name

1. VDD 5. DRAIN

2. FB 6. 

3. CL 7. SOURCE

4. VCC 8. SOURCE

 Marking Symbol: MIP2K3

MIP2K30MS

2 Ver. AEF

 Electrical Characteristics TC = 25°C±2°C

Parameter Symbol Conditions Min Typ Max Unit

Control functions

Output frequency

fosc VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA90 100 110 kHz

fosc(L) VCC = 15 V, VD = 5 V, IFB: Open,

ICL < ICL1 9 12 15 kHz

Jitter frequency deviation ∆fVCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA5.5 kHz

Jitter frequency modulation rate fM VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA260 Hz

Maximum duty cycle MAXDC VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA45 47.5 50 %

VDD voltage VDD VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA5.4 5.9 6.4 V

UV lockout threshold voltage VUV VD = 5 V, IFB = 20 mA, ICL = 50 mA 4.6 5.1 5.6 V

VCC start voltage VCC(ON) VD = 5 V, IFB = 20 mA, ICL = 50 mA 5.9 6.9 7.9 V

VCC charge stop threshold voltage VCC1 VD = 40 V, FB: Open, CL: Open 10 11 12 V

Feedback threshold voltage IFB1 ON → OFF

VCC = 15 V, VD = 5 V, ICL = 50 mA24.6 41 57.4 mA

Feedback hysteresis current IFBHYS VCC = 15 V, VD = 5 V, ICL = 50 mA 2 mA

FB pin current at heavy load IFB0 ICC0 → ICC

VCC = 15 V, VD = 5 V, ICL = 50 mA6 9.5 13 mA

FB pin voltage VFB VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA0.7 1.0 1.3 V

Supply current ICC VCC = 15 V, VD = 5 V, IFB = 20 mA,

ICL = 50 mA0.25 0.40 0.50 mA

Supply current at light load ICC(OFF) VCC = 15 V, VD = 5 V,

IFB = IFB1 + 5 mA, ICL = 50 mA0.26 0.36 0.46 mA

Supply current at heavy load ICC0 VCC = 15 V, VD = 5 V, IFB: Open,

ICL = 50 mA0.45 0.60 0.75 mA

VDD charging current

Ich1 VDD = 0 V, VD = 40 V, FB: Open,

CL: Open -7.5 -5.5 -3.5 mA

Ich2 VDD = 4 V, VD = 40 V, FB: Open,

CL: Open -3.0 -2.0 -1.0 mA

CL pin voltage VCL VCC = 15 V, VD = 5 V, FB: Open,

ICL = ICL1 2.0 2.3 2.6 V

Dropped fosc CL pin current *2ICL1 fosc → fosc(L)

VCC = 15 V, VD = 5 V, FB: Open 16.5 22 27.5 mA

CL pin hysteresis current

*2ICLHYS VCC = 15 V, VD = 5 V, FB: Open 1.5 mA

MIP2K30MS

Ver. AEF 3

 Electrical Characteristics (continued) TC = 25°C±2°C

Parameter Symbol Conditions Min Typ Max Unit

Circuit protections

Self protection current limit *1, 3

ILIMIT VCC = 15 V, FB: Open, ICL = 50 mA,

DUTY = 30% 0.45 0.50 0.55 A

ILIMIT modiﬁed coefﬁcient *1, 3

R_slope VCC = 15 V, FB: Open, ICL = 50 mA 40 mA/ms

Minimum ILIMIT

ILIMITmin Ton = 3 ms, VCC = 15 V, FB: Open,

ICL = 0 mA52 115 178 mA

Drain current at light load

ID(OFF) Ton = 3 ms, VCC = 15 V,

IFB = IFB1 + IFBHYS, ICL = 50 mA45 110 165 mA

Leading edge blanking delay

ton(BLK) VCC = 15 V, FB: Open, ICL = 50 mA 230 290 350 ns

Current limit delay td(OCL) 100 150 200 ns

Over voltage protection VCC(OV) VD = 5 V, FB: Open, ICL = 50 mA 21 23.5 26 V

Thermal shutdown temperature TOTP 130 140 150 °C

Output

Power up reset threshold voltage VDDreset 1.8 2.6 3.5 V

ON state resistance RDS(ON) ID = 100 mA 10 13 W

OFF state current IDSS VCC = 26 V, VD = 650 V, FB: Open,

CL: Open 10 20 mA

Breakdown voltage VDSS VCC = 26 V, ID = 100 mA, FB: Open,

CL: Open 700 V

Rise time *4tr VCC = 15 V, VD = 5 V, FB: Open,

ICL = 50 mA100 ns

Fall time *4tf VCC = 15 V, VD = 5 V, FB: Open,

ICL = 50 mA25 ns

Supply voltage characteristics

Drain supply voltage VD(MIN) VCC: Open, FB: Open, CL: Open 50 V

Note) 1. Measurement circuit

MIP2K30MS

4 Ver. AEF

 Electrical Characteristics (continued) TC = 25°C±2°C

2. *1: ILIMIT vs. ICL Typical characteristic

*2: fosc vs. ICL Typical characteristic

*3: ILIMIT Measurement

*4: tr, tf Measurement

MIP2K30MS

Ver. AEF 5

 Frequency jitter function

By frequency jitter function, frequency jitter variation(∆f) changes periodically, by frequency of frequency jitter modulation factor (fM) as

shown below.

　　fosc = 100 kHz (typ.), ∆f = 5.5 kHz (typ.), fM = 260 Hz (typ.)

 Adapter circuit sample (MIP2K4)

 Electric characteristics (MIP2K4：Worldwide input, 8.3V/1.5A output)

Request for your special attention and precautions in using the technical information and

semiconductors described in this book

(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and

regulations of the exporting country, especially, those with regard to security export control, must be observed.

(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples

of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any

other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any

other company which may arise as a result of the use of technical information described in this book.

(3) The products described in this book are intended to be used for general applications (such as office equipment, communications

equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.

Consult our sales staff in advance for information on the following applications:

 Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,

life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of

the products may directly jeopardize life or harm the human body.

It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with

your using the products described in this book for any special application, unless our company agrees to your using the products in

this book for any special application.

(4) The products and product specifications described in this book are subject to change without notice for modification and/or improve-

ment. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards

in advance to make sure that the latest specifications satisfy your requirements.

(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions

(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute

maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any

defect which may arise later in your equipment.

Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure

mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire

or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.

(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,

thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which

damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.

(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.

20130322

Precautions on the Sales of IPDs

Attached table "IPD availability by customer"

1) The sale and/or the export of IPD products to customers located in certain countries is restricted by the Agreement made and

executed by and between Power Integrations, Inc. and Panasonic Corporation. For details, refer to the following Attached table

"IPD availability by customer."

2) IPD products purchased from our company, or its authorized agents, hereinafter referred to as our company, shall be used only

for production purposes by those parties who have duly purchased IPD products. Those who have purchased IPD products shall

not use such IPD products in unmodified form for re-sale, loan, or sample shipment for evaluation purposes to any other

parties.

3) If a party who has duly purchased IPD products subcontracts its production to any other parties, including its subsidiaries or any other

third parties inside and/or out of Japan, and the IPD products are consigned to such subcontracting parties thereat, such party is

obligated to monitor and control the quantity of IPD products to prevent any of the aforementioned re-sale, loan or sample shipments

from taking place.

4) In the event that any actual or threatened breach or violation of any of the above mentioned 2) or 3) has occurred or is about to occur,

our company will hold all shipments of IPD products and may request the customer to disclose necessary documentation describing

the status of our end-users and/or distribution channels.

Note) The products of MIP50**, MIP51**, and MIP7** are excluded from above-mentioned precautions, 1) to 3).

Application

For power supply

For DC-DC converter

For power supply

For EL driver

For LED lighting driver

For lamp driver/

car electronics accessories

Companies/areas to which

products cannot be sold

Companies in European

and American countries

Asian companies in Asia

Other local companies

Companies in European

and American countries

Other local companies

No restrictions in terms of

contract

Companies/areas to which

products can be sold

Japanese companies in Japan

Japanese companies in Asia

(50% or more owned)

Japanese companies in Japan

Japanese companies in Asia

(50% or more owned)

Asian companies in Asia

No restrictions in terms of

contract

Note)

For details, contact our sales division.

Parts No.

MIP01**

MIP2**

MIP9A**

MIP1**

MIP4**

MIP52**

MIP56**

MIP9E**

MIP50** MIP7**MIP51**

MIP02**

MIP3**

MIP9L**

MIP00**

MIP55**

MIP816/826

MIP53**

MIP803/804