Miniature chip resistor arrays have 4 and 2
resistor elements integrated as a single
component.
Features
Miniature (2.0×1.0mm) Resistor Arrays
Max. 60% space saving compared with the
use of standard chip array (3.2×1.6mm)
0.5mm Termination pitch (Same as IC
lead-pin pitch)
Easy designing of pattern layout and
improve electrical characteristics for curcuit
* Please consult combination of different
resistance type
How to Order
CRB2A 4E 103 J H
Series
(CRB2A: 2.0×1.0mm, concave termination, 4 elements)
(CRC11A: 1.0×1.0mm, convex termination, 2 elements)
Number of elements (4E: 4 elements)
(2E: 2 elements)
Resistance Value (3 digits numbering)
472 = 4.7kW, 103 = 10kW
000 = 0W (Chip Jumper Array)
Tolerance
J±5% Blank Chip Jumper Array
Packaging
Code Form
Material
Packing unit
HTaping Paper
10000 pcs./ reel
• 2mm pitch taping
RoHS Compliant
4 element chip Resistors Array CRB2A4E series (Concave Termination)
2 element chip Resistors Array CRC11A2E series (Convex Termination)
Dimensions (Unit: mm)
,
#
7
4
D
0
E B
2 2 2 2
2222
#2"!%SERIES
(Unit: mm)
#2#!%SERIES
,
C
0
4
E
2 2
22
7
D
Code L W T P b
Dimensions
2.0 +0.10
0.10 1.0 +0.10
0.10 0.4 +0.10
0.10 0.5 typ. φ0.15 typ.
Code c d e
Dimensions
0.2 +0.15
0.15 0.25 +0.15
0.15 0.25 typ.
No marking on chips.
Code L W T P
Dimensions
1.00 +0.10
0.10 1.00 +0.10
0.10 0.35 +0.05
0.05 0.65 typ.
Code c d e1
Dimensions
0.20 +0.15
0.15 0.20 +0.15
0.15 0.33 +0.10
0.10
No marking on chips.
Rating
Chip resistor arrays Chip jumper array
Item Rating Item Rating
Rated power (70°C) 1/ 32W/ element
Rated current 1A
Max. working *
voltage 25V
Max. Over-load
voltage 50V
Resistance value 10W to 1MW
Conductive
resistance value
50mW max.
Tolerance J: ±5%
Working
Temperature 55 to +125°C
Number of
elements 4E: 4 elements, 2E: 2 elements

* Rated Voltage:
Rated power × Resistance value, whichever is less.
* Standard Resistance Value: E-6 Series
* Please contact sales engineer for any other requirements of the nominal resistance value
and the tolerance.
Chip Resistor Arrays
CRB2A4E (Concave), CRC11A2E (Convex) Series
8 element chip Resistor Array/ CRB6A8E Series (Concave Termination)
Features
Equal length conductors can be traced
out from 0.8mm pitch termination
How to Order
CRB6A 8E 390 G U
Series CRB6A
Number of elements
8E = 8 elements
Resistance value
3 digits numbering
Tolerance
G±2% J±5%
Packaging
UTaping plastic 4,000 pcs./ reel
Rating
Chip Resistor Arrays
Item Rating
Rated power (70°C) 1/ 16W/ element
Max. working voltage*
50V
Max. over-load voltage
100V
Resistance value 10W to 1MW
Tolerance G: ±2%, J: ±5%
Working temperature
55 to +125°C
Number of elements 8E: 8 elements

* Rated Voltage: Rated power × Resistance value,
whichever is less.
* Standard Resistance Value: E-6 Series
* Please contact sales engineer for any other requirements of
the nominal resistance value and the tolerance.
RoHS Compliant
Dimensions (Unit: mm)
7
0
2 2 2
2=2=2=2=2=2=2=2
2 2 2 2
D
#
4
,
E
2
Code
Dimensions
L6.4±0.2
W1.6±0.2
T0.6±0.1
P0.8 typ.
c0.3±0.2
d0.4±0.15
e
(Top side)
0.5±0.1
e
(Bottom side)
0.4±0.15
Chip Resistor Network/ RNA4A Series (Concave Termination)
Features
Reduction in mounting costs & Process
Save PCB space
Eight resistors in one SMD package
Reduction of inventory control costs
Applications
Lap Top Computer Notebook Computer
Printer Hard Disk Drive
CD ROM Facsimile
How to Order
RNA4A 8E 103 J U
Series
Number of elements (8E: 8 elements)
Resistance code (3 digits)
Resistance tolerance (J: ±5%)
Packaging
UPlastic Taping, 4,000 pcs./ reel
* Taping Qty.: 4000 pcs./ 7 inch reel (4mm pitch)
Carrier Tape: plastic
Specifications
Item Rating
Rated power (70°C) 1/ 16W (0.0625W)/
Element
Max. working voltage*25V
Max. over-load voltage 50V
Resistance value 100W to 220KW
Tolerance J: ±5%
Number of elements 8E: 8 elements
Working temperature 55 to +125°C

* Rated Voltage: Rated power × Resistance value,
whichever is less.
* Standard Resistance Value: E-6 Series
* If resistance value under 100W is needed, please contact
sales.
RoHS Compliant
Dimensions (Unit: mm)
7

%
"
,
!$0&
4
%
& !
"
Code
Dimensions
L4.0±0.15
W2.1±0.15
T0.6±0.1
A1 0.5±0.1
B1 0.25±0.15
E1 0.5±0.1
F1 0.3±0.15
D0.3 typ.
P0.8 typ.
A2 0.4±0.1
B2 0.4±0.15
E2 0.5±0.1
F2 0.35±0.15
Circuit Diagram
2 2 2 2
2 2 2 2
Nominal resistance value is all the same.
Chip Resistor Array/ CRB6A8E Series
Chip Resistor Network/ RNA4A Series
Electrical Characteristics
Item
Standard Test Conditions
Resistor Jumper Resistor Jumper
DC Resistance Within Initial Tolerance 50mW max. Power Contdition A
(20°C, 65%RH)
Temperature
Characteristics
Resistance (W) TCR (ppm/ °C)
10
1M<
R
R
R
<10
1M
100 to +600
250 to +250
500 to +300
Test Temperature: 25,125 (°C)
DR/ R=R2R1/ R1×1/ T2T1×106
DR/ R: Temp. Coefficient
(ppm/ °C)
T1: 25 (°C)
T2: 125 (°C)
R1: T1 Resistance at (W)
R2: T2 Resistance at (W)
Short-time
Overload
DR/ R ± (2.0%+0.10W) max.
of the initial value 50mW max.
(1) Apply 2.5×rated voltage for
5 sec.
(2) Wait 30 minutes
(3) Measure resistance
(1) 2A for 5 sec.
(2) Wait 30 minutes
(3) Measure
resistance
Visual No evidence of mechanical damage
intermittent overload
Intermittent
Overload
DR/ R ± (5%+0.1W) max.
of the initial value 50mW max.
(1) Perform 10000 voltage
cycles as follows:
ON
(2.5×rated voltage)
1 sec.
OFF 25 sec.
(2) Stabilization time 30 min.
without loading
(3) Measure resistance
(1) Perform 10000
current cycles as
follows:
ON (2A) 1 sec.
OFF 25 sec.
(2) Wait 30 minutes
(3) Measure
resistance
Visual No evidence of mechanical damage
Dielectric
Withstanding Voltage No evidence of mechanical damage
Apply 300VAC for 1 sec.
Apply 100V DC.
Insulation Resistance 108W min.
Test Conditions and Standards
CRB, CRC Series
Mechanical Characteristics
Item
Standard Test Conditions
Resistor Jumper Resistor Jumper
Terminal
Strength
DR/ R ± (1%+0.05W) max.
of the initial value 50mW max. Apply the load as show:
Measure resistance during load application

2

F
 
pMAX
5NITMM
"ENDINGIN
SECONDS
PC board: Glass epoxy t=1.6
Visual No evidence of mechanical damage after loading
Soldering Heat
Resistance
DR/ R ± (1%+0.05W) max.
of the initial value 50mW max. Immerse into molten solder at 260±5°C for 10±1 sec.
Stabillize component at room temperature for 1hr.
Measure resistance.
Visual No evidence of leaching
Solderability Coverage95% each termination end
Immerse in Rogin Flux for 2±0.5 sec. and in
SN62 solder at 235±5°C for 2±0.5 sec.
Anti-Vibration
Test
DR/ R ± (1%+0.1W) max.
of the initial value 50mW max. 2 hrs. each in X, Y and Z axis. (TTL 6hrs.) 10 to 55 Hz
sweep in 1 min. at 1.5mm amplitude.
Visual No evidence of mechanical damage
Solvent
Resistance
DR/ R ± (0.5%+0.05W) max.
of the initial value 50mW max. Immerse in static state butyl acetate at 20°C to 25°C
for 30±5 sec.
Stabillize component at room temperature for 30 min.
then measure value.
Visual No evidence of mechanical damage
Environmental Characteristics
Item
Standard Test Conditions
Resistor Jumper Resistor Jumper
Temperature
Cycle
DR/ R ± (1%+0.05W) max.
of the initial value 50mW max.
1) Run 5 cycles as follows: 55±3°C for 30 min.
125±3°C for 30 min. Room temp. for 10 to 15 min.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
Low
Temperature
Storage
DR/ R ± (2%+0.1W) max.
of the initial value 50mW max. 1) Dwell in 55°C chamber without loading for
1000 +48
0 hrs.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
High
Temperature
Storage
DR/ R ± (3%+0.1W) max.
of the initial value 50mW max. 1) Dwell in 125°C chamber without loading for
1000 +48
0 hrs.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
Moisture
Resistance
DR/ R ± (3%+0.1W) max.
of the initial value 50mW max. 1) Dwell in temp.: 65°C RH90 to 95%RH chamber
without loading for 1000 +48
0hrs.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
Life Test
DR/ R ± (3%+0.1W) max.
of the initial value 50mW max. 1) Temp.: 70±3°C Voltage: (rated voltage) on 90 min.
off 30 min. Duration: 1000 +48
0hrs.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
Loading Life
in Moisture
DR/ R ± (3%+0.1W) max.
of the initial value 50mW max. 1)
Temp.: 40±2°C RH: 90 to 95% Voltage Cycle: on 90
min. (rated voltage) off 30 min. Duration: 1000
+48
0
hrs.
2) Stabilize component at room temperature for 1hr.
then measure value.
Visual No evidence of mechanical damage
Test Conditions and Standards
CRB, CRC Series
Tape & Reel
Reel (Unit: mm)
%
#
2$
! 7
T
"
Code A B C D E W t R
Width: 8mm
φ178±2.0 φ50 min.
φ13.0±0.5 φ21.0±0.8
2.0±0.5 10.0±1.5 2.5 max. 1.0
Width: 12mm
13.0±1.5
Carrier Tape (8mm) (Unit: mm)
& ( '
!
"
$
#
%
*T
Dimension
Code
TYPE A B C D E F G H J t
0404 1.2±0.1 1.2±0.1
8.0±0.2 3.5±0.05 1.75±0.1
2.0±0.1
2.0±0.05 4.0±0.1 φ1.5 +0.1
0
0.6 max.
0804 1.25±0.2 2.25±0.2
1.1 max.
0805 1.65±0.2 2.4±0.2
4.0±0.1
1206 2.0±0.2 3.6±0.2
• Carrier Tape (12mm) (Unit: mm)
Dimension
Code
TYPE A B C D E F G H J T K
1020 2.9±0.2 5.3±0.2
12.0±0.3 5.5±0.05 1.75±0.1 4.0±0.1 2.0±0.1 4.0±0.1 φ1.5 +0.1
00.6 max. 1.4 max.
1608 2.5±0.2 4.4±0.2
2512 3.5±0.2 6.7±0.2
2506 2.0±0.2 6.9±0.2
Taping Quantity per reel (Unit: pcs.)
TYPE Series φ178 reel
0404 CRC11A2E, ATC1A 10000 (2mm pitch)
0804 CRB2A4E 10000 (2mm pitch)
0805 LR21 5000 (4mm pitch)
1206 LR32 5000 (4mm pitch)
1020 LR50 4000 (4mm pitch)
1608 RNA4A 4000 (4mm pitch)
2512 LR63 4000 (4mm pitch)
2506 CRB6A8E 4000 (4mm pitch)
Thick Film Chip Resistors
Tape & Reel
Recommended Land Patterns
Chip Type (Unit: mm)
B B
A
C
EIA Size A B C
0805 1.0 0.8 1.2
1020 1.4 1.0 5.0
1206 2.2 0.9 1.5
2512 5.0 1.0 3.0
Array Type (Unit: mm)
3OLDERRESIST
D
A
C
B
Series a b c d
CRB2A4E 0.4 1.5 0.25 0.5
CRC11A2E 0.5 1.5 0.4 0.65
CRB6A8E 0.7 2.3 0.4 0.8
ATC1A 0.5 1.5 0.4 0.65
(Unit: mm)
2.!!%3ERIES





 
Recommended Land Patterns
Circuit design
1) Once application and assembly environments have been checked,
the resistors may be used in conformance with the catalog and the
specifications.
2) Please consult the manufacturer in advance when the resistors is
used in devices such as: devices which deal with human life, i.e.
medical devices; devices which are highy public orientated; and
devices which demand a high standerd of liability.
3) Please use the resistors in conformance with the operating
temperature provided in both the catalog and the specifications.
4) Please keep voltage under the rated voltage which is applied to the
resistor.
5) Do not use the resistor in an environment where it might easily
exceed the respective provisions concerning shock and vibration
specified in the catalog and specifications.
6) Please do not use the resistor in the following environments.
State that water, oil, and solvent hang in resistor
State where poisonous gas (sulfur and chlorine, etc.) exists
State that direct sunshine, radiation, and ultraviolet, etc. are irradiated
7) There is a thing that resistance changes according to the stuff of
the resin when the coating with the resin is given.
Please use resin coating after confirming the characteristic.
8) There is a thing that resistance changes according to flux and
cleaner.
Please use flux and cleaner after confirming the characteristic.
9) Please consult about a lead free products.
Storage
1) Keep storage place temperature +5 to +35°C, humidity 45 to 75%
RH.
2) Please keep parts out of poisonous gas such as sulfur or chlorine
in the air and out of salty moisture, or they may cause rust of
terminal and poor solderability. Please consider the above-
mentioned item after mounting.
3) Soldering iron
Temperature soldering iron 300±5°C *
Time 3 sec. max. *
*Do not place the soldering iron on the chip. Soldering iron is 30W max.
Soldering method
1) Recommendable temperature profile
REFLOW






4EMPo#
SEC SEC SECMAX
4IME
TOo#
-ORETHANo#
SECMAX
PREHEAT
2) Recommendable temperature profile
#AUTION#OOLINGAFTERSOLDERINGSHOULDBEASSLOWASPOSSIBLE
%NSURETHATTHECHIP2ESISTORISPREHEATEDADEQUATELY
%NSURETHATTHETEMPERATUREDIFFERENCE4DOESNOTEXCEED°#
WAVE






4EMP°#
TOSEC SECMAX
4IME
TO°#
4
PREHEAT
3) Pb-free recommendable temperature profile
REFLOW






4EMPo#
±SEC
4IME
0EAKTEMPERATURE
o#±o#
TOSECMAX
-ORETHANo#
SECMAX
TOo#SEC
TOo#
PREHEAT
Precautions