MEC1-1XX-XX-XX-D-XX-XX REVISION AJ DO NOT SCALE FROM THIS PRINT (No OF POS -1) x .03937 [1.00] .109 2.77 REF No OF POSITIONS 05, 08, 10, 20, 30, 40 , 50, 60 & 70 (PER ROW, SEE TABLE 2) C ({(No OF POS +2) x .03937 [1.00]} + .100 [2.54]) .007[.18] CARD THICKNESS -02: .062 [1.58] THICK CARD (USE MEC1-XX-S-D-X-X) .005[.13] .026 0.66 REF 16 02 FLOW INHIBITORS AT VENDOR DISCRETION 40 .275 6.99 REF 15 01 1.5 MAX SWAY (ANY DIRECTION) C .050 1.27 (No OF POS +2) x .03937 [1.00] REF "A" .350 8.89 REF 39 PLATING SPECIFICATION -F: 3" FLASH GOLD IN CONTACT AREA, MATTE TIN ON TAIL -L: 10" LIGHT GOLD IN CONTACT AREA, .072 1.83 REF MATTE TIN ON TAIL -S: 30" SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL MEC1-XX-X-D-X-X -FM: 3" FLASH GOLD IN CONATACT AREA, MATTE ON TIN TAIL -LM: 10" LIGHT IN CONTACT AREA, MATTE TIN ON TAIL -SM: 30" SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL FIG 1 MEC1-120-02-X-D SHOWN C SEE NOTE 5 C +.005 OTHER OPTIONS -LC: LOCKING CLIP (SEE NOTE 8) (SEE FIG 2)(USE LC-05-TM) -A: ALIGNMENT PIN (MOLDED, SEE FIG 4, SHT 2) (USE MEC1-XX-X-D-X-A) -K: POLYIMIDE FILM PAD (SEE FIG 6, SHT 2)(USE K-DOT-.310-.406-.005) -TR: TAPE & REEL PACKAGING (N/A IN 70 POSITION)(SEE FIG 5, SHT 2) POLARIZED OPTION (SEE TABLE 2) -BLANK: BODY IS POLARIZED -NP: NO POLARIZATION (-05 THRU -30 ONLY) (USE MEC1-XX-X-D-N-X) ROW SPECIFICATION -D: DOUBLE ROW (USE MEC1-XX-X-D-X-X) .160 4.07 REF +0.13 .020 - .010 0.51 - 0.25 +.004 903 +0.10 .356 - .002 9.04 - 0.05 "A" SEE NOTE 2 .334 8.49 C-113-02-XX .320 8.13 REF .006 0.15 REF .030 0.75 .079 2.00 SECTION "A"-"A" PACKAGING VIEW IN-PROCESS (FILL STEP) NOTES: C 40 01 39 MEC1-XX-X-D-N-X C +.005 02 +0.13 0.00 .535 - .000 13.59 1. MINIMUM PUSHOUT FORCE: 10 oz. 2. COPLANARITY: POS -05 THRU -26: .004 [.10] POS -27 THRU -70: .006 [.15] 3. C REPRESENTS A CRITICAL DIMENSION. 4. PACKAGE ALL POSITIONS IN TUBES. (WITH -K OPTION, USE PT-1-24-01-70 TUBE & TP-29 TUBE PLUG) (WITHOUT -K OPTION, USE PT-1-24-01-69 TUBE & TP-07 TUBE PLUG) 5. MAXIMUM CUT FLASH: .010; FLASH NOT TO EXTEND BELOW LEADS. 6. MAXIMUM ALLOWABLE BOW: .002 INCH/INCH AFTER ASSEMBLY. 7. MAXIMUM BURR: .003[.08], BURR DIRECTION TO BE OPPOSITE OF SOLDER PAD AREA 8. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION. FOR -K OPTION -NP: NON-POLARIZED OPTION (AVAILABLE ON -05, -08, -10, -20 & -30 POS. ONLY) (SHOWN: MEC1-120-02-X-D-NP) UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ANGLES .XX: .01 [.3] 2 .XXX: .005 [.13] .XXXX: .0015 [.038] MATERIAL: NO -K OPTION TUBE: PT-1-24-01-70 PLUG: TP-29 TUBE: PT-1-24-01-69 PLUG: TP-07 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING INSULATOR: VECTRA E130i COLOR: BLACK CONTACT: BeCu 190 HM F:\DWG\MISC\MKTG\MEC1-1XX-XX-XX-D-XX-XX-MKT.SLDDRW SHEET SCALE: 1.5:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: info@SAMTEC.com code: 55322 DESCRIPTION: 1mm MINI-EDGE CARD ASSEMBLY DWG. NO. MEC1-1XX-XX-XX-D-XX-XX BY: KEVIN B 5/11/2000 SHEET 1 OF 2 REVISION AJ FIG 5 .059 1.50 (TYP) -TR: TAPE & REEL PACKAGING VIEW (NOT DRAWN TO SCALE) LC-05-TM .010 0.25 REF .056 1.42 REF (TYP) 2 MAX SWAY (EITHER DIRECTION) C POSITION 1 C ({(No OF POS +2) x .03937[1.00]} + .0490[1.245]) .005[.13] FIG 2 -LC OPTION (SHOWN: MEC1-120-02-X-D-LC) .0625 1.588 REF MEC1-XX-X-D-X-A .035 0.89 REF (TYP) .055 1.40 REF ({(No OF POS +2) x .03937[1.0000]} + .0490[1.245]) REF .0625 1.59 REF FIG 4 -A: ALIGNMENT PIN OPTION (MOLDED) (SHOWN: MEC1-120-02-X-D-A) FIG 6 -K: POLYIMIDE FILM PAD OPTION (SHOWN: MEC1-120-02-X-D-K) "M" "P" 02 01 .376 9.55 REF USER DIRECTION OF UNREELING F:\DWG\MISC\MKTG\MEC1-1XX-XX-XX-D-XX-XX-MKT.SLDDRW 16 15 40 PROPRIETARY NOTE 39 .310 7.87 .361 9.17 THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 1.5:1 NOTE: "M" = USED MEASURED DIMENSION (REF) "P" = {("M" - .310 [7.87]) / 2} .020 [.51] 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: info@SAMTEC.com code: 55322 DESCRIPTION: 1mm MINI-EDGE CARD ASSEMBLY DWG. NO. MEC1-1XX-XX-XX-D-XX-XX BY: KEVIN B 5/11/2000 SHEET 2 OF 2