E M C C o m p o n e n t s April 2014 Common Mode Filters For high-speed differential signal line, general signal line ACM-E series ACM2012E [0805 inch]* * Dimensions Code JIS[EIA] (2/9) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (3/9) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Compatible with lead-free solders For high-speed differential signal line, general signal line Overview of the ACM-E Series FEATURES Downsized, low height wound type chip common mode filter that maintains required common mode filter characteristics. Impedance for common mode noise can clear 1000: [100MHz], and has excellent EMC suppression. Differential mode impedance is suppressed, so there is virtually no affect on high speed signals. APPLICATION Common mode noise countermeasure for high-speed differential signals where influence to the signal is a concern. USB line for PCs and peripheral devices. IEEE1394 lines and ETHERNET lines for PCs, STBs, etc. LCD panel LVDS and Panel Link lines. PART NUMBER CONSTRUCTION - ACM 2012 Series name LxWxH Dimensions (mm) 2012 2.0x1.2x1.0 E - 900 Impedance (:) at 100MHz 670 67 900 90 121 120 181 180 251 250 391 390 681 680 102 1000 Product internal code E - 2P Number of lines 2P 2 lines - T - 00 Packaging style T TL o180mm reel o330mm reel Internal code 00 01 General signal line High-speed differential signal line OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type ACM2012E Temperature range Operating Storage temperature temperature C C -40 to +85 -40 to +85 Reel diameter Package quantity Individual weight mm o180 o330 pieces/reel 2,000 10,000 mg 8 The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (4/9) E M C C o m p o n e n t s Overview of the ACM-E Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 10 to 30s Peak Temp. T4 245C Time t3 5s * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (5/9) E M C C o m p o n e n t s ACM-E series ACM2012E Type (General signal line) SHAPE & DIMENSIONS 1.00.1 2.00.2 0.4 2 3 1 4 0.5 1.20.2 0.3 1.2 0.3 0.4 0.05 Dimensions in mm CIRCUIT DIAGRAM 1 4 2 3 0.4 0.4 0.4 RECOMMENDED LAND PATTERN * No polarity 0.75 1.1 0.75 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (6/9) E M C C o m p o n e n t s ACM-E series ACM2012E Type (General signal line) ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance (: ) [100MHz 6725% 9025% 12025% 18025% 25025% 270min. (390typ.) 510min. (680typ.) 750min. (1000typ.) DC resistance (: )max.[1 line] 0.35 0.35 0.45 0.60 1.00 0.80 1.80 2.50 Rated voltage (V)max. 50 50 50 50 50 50 50 50 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Rated current (A)max. 0.50 0.33 0.30 0.25 0.20 0.30 0.17 0.15 Part No. ACM2012E-670-2P-T00 ACM2012E-900-2P-T00 ACM2012E-121-2P-T00 ACM2012E-181-2P-T00 ACM2012E-251-2P-T00 ACM2012E-391-2P-T00 ACM2012E-681-2P-T00 ACM2012E-102-2P-T00 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 102 Common mode 681 Common mode 391 Common mode Impedance () 1000 251 Common mode 181 Common mode 121 Common mode 900 Common mode 100 670 Common mode 670 Differential mode 900 Differential mode 121 Differential mode 181 Differential mode 251 Differential mode 391 Differential mode 681 Differential mode 102 Differential mode 10 1 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (7/9) E M C C o m p o n e n t s ACM-E series ACM2012E Type (high-speed differential signal line) SHAPE & DIMENSIONS 1.00.1 2.00.2 0.4 2 3 1 4 0.5 1.20.2 0.3 1.2 0.3 0.4 0.05 Dimensions in mm CIRCUIT DIAGRAM 1 4 2 3 0.4 0.4 0.4 RECOMMENDED LAND PATTERN * No polarity 0.75 1.1 0.75 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (8/9) E M C C o m p o n e n t s ACM-E series ACM2012E Type (high-speed differential signal line) ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance (: ) [100MHz 6725% 9025% 12025% 18025% DC resistance (: )max.[1 line] 0.45 0.55 0.65 1.00 Rated voltage (V)max. 50 50 50 50 Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A Equivalent measurement equipment may be used. Rated current (A)max. 0.35 0.30 0.27 0.25 Part No. ACM2012E-670-2P-T01 ACM2012E-900-2P-T01 ACM2012E-121-2P-T01 ACM2012E-181-2P-T01 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 181 Common mode 121 Common mode Impedance () 1000 900 Common mode 670 Common mode 100 181 Differential mode 121 Differential mode 10 900 Differential mode 670 Differential mode 1 1 10 100 Frequency (MHz) 1000 10000 Measurement equipment Product No. Manufacturer 4991A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm (9/9) E M C C o m p o n e n t s ACM-E series Packaging style REEL DIMENSIONS 2.00.5 E Type W1 9.50.5 9+1/-0 W2 13.51 131 N 1001 60+1/-0 E 2 typ. 2 typ. N ACM2012E A o3302 o1803 1.0 o13.00.2 W1 o21.00.8 W2 A Dimensions in mm TAPE DIMENSIONS P2 t P0 W B F E oD0 A K P1 Dimensions in mm Type ACM2012E A 1.40.1 B 2.250.1 oD0 1.5+0.1/0 E 1.750.1 F 3.50.1 P0 4.00.1 P1 4.00.1 P2 2.00.1 W 8.00.2 K 1.150.05 t 0.200.05 500 to 560min. 160min. Taping 440min. Drawing direction Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140403 / cmf_signal_acm-e_en.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: ACM2012E-181-2P-T01 ACM2012E-670-2P-T01 ACM2012E-121-2P-T01 ACM2012E-900-2P-T01 ACM2012E-9002P-T00