PRODUCT DESCRIPTION
Soder-Wick Lead-Free is the state of the
art in desoldering technology. It is specially
designed for removal of today’s high
temperature lead-free solders. The single
layer weave used for Soder-Wick Lead-
Free braid is lighter in mass than any other
desoldering braid available and allows for
lead-free solder removal at lower
temperatures. Soder-Wick Lead-Free
responds faster than any other conventional
desoldering braid. This unique design
minimizes overheating and requires less
“contact” time thus preventing heat damage
to the PCB and sensitive components. For
Lead-Free rework, Soder-Wick has the
answer.
Fastest wicking and heat transfer
High capacity for solder uptake
Halide free, no corrosive residues
Minimizes risk of heat damage to pads,
components and PBCs
Can be used with Tin/Lead solders
RoHS compliant
TYPICAL APPLICATIONS
Soder-Wick Lead-Free desoldering braid
safely removes solder from:
Thru-hole Components
SMT Pads and BGA Pads
Micro Circuits
Terminals, Lugs and Posts
Identification Script
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Flux Type High-Temperature No Clean
Type ROL0
Specifications: ANSI/IPC J STD-004
MIL-F-14256 F
No Clean Flux Spec: MIL-STD-883B
Bellcore TR-NWT-000078
ANSI/IPC J SF818
Shelflife: 2 years
RoHS/WEEE
Status
Size # Width
Inches
Color Width
Metric
2 .060” Yellow 1.5 mm
3 .080” Green 2.0 mm
4 .110” Blue 2.8 mm
STATIC DISSIPATIVE PACKAGING
Soder-Wick Lead-Free is packaged on
Static Dissipative bobbins to minimize the
risk of damage associated with static
electricity. The static dissipative bobbins
qualify as electrostatic discharge protective
per MIL-STD-1686C and MIL-HDBK-
263B and meet the static delay rate
provision of MIL-B-81705C.
TDS # SWPbFree
CHEMTRONICS
Technical Data Sheet
Soder-Wick Lead-Free SD Desoldering Braid
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
1) Choose a Soder-Wick Lead-Free braid width
equal to or slightly larger than the pad or
connection.
2) Choose a solder iron tip equal to or slightly
larger than the pad or connection.
3) Set temperature of iron between 650 and 750F
4) Place wick on solder joint or pad and place tip
of hot iron on top of wick
5) As solder becomes molten, the color of the wick
will change from copper to silver.
6) Remove wick and iron simultaneously once
color change has stopped.
7) The component lead / pad is now clean and free
from solder.
8) Clip and discard the used portion of the wick.
9) If needed, clean PCB with CircuitWorks Lead-
Free Flux Remover Pen CW9400 and remove
soils with a ControlWipes absorbent wipe.
SODER-WICK IS DESIGNED TO MEET
OR EXCEED THE FOLLOWING:
MIL-F-14256F, Type R
NASA-STD-8739.3
DOD-STD-883E, Method 2022
ANSI/IPC J STD-004, Type ROL0
BELLCORE TR-NWT-000078
ANSI/IPC J SF-818
SODER-WICK SD BOBBINS ARE
DESIGNED TO MEET OR EXCEED:
MIL-STD-2000A
MIL-B-81705C
MIL-STD-1686C
MIL-HDBK-263B
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application
related questions. The toll free number is:
1-800-TECH-401.
AVAILABILITY
40 Series Lead-Free No Clean Flux
25 bobbins / bag
Part # Size
5 feet 10 feet
40-2-5 40-2-10 2
40-3-5 40-3-10 3
40-4-5 40-4-10 4
VacuPak
Packaging Part # Size
SW14025
2
SW14035
3
SW14045 4
The VacuPak Can contains ten
five-foot bobbins in a vacuum
sealed can. This package
provides the highest level of
cleanliness and freshness. Great
for tool kit storage.
NOTE: This information is believed to be accurate. It is
intended for professional end users having the skills to
evaluate and use the data properly. ITW
CHEMTRONICS does not guarantee the accuracy of
the data and assumes no liability in connection with
damages incurred while using it.
MANUFACTURED BY:
ITW Chemtronics
8125 Cobb Center Drive
Kennesaw, GA 30152
1-770-424-4888 REV. B (06/06)
Chemtronics, Soder-Wick and CircuitWorks are
registered trademarks of ITW Chemtronics. All rights
reserved. Vacu-Pak and ControlWipes are trademarks of
ITW Chemtronics. All rights reserved.
DISTRIBUTED BY: