DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator General Description Features The AAT2500 is a member of Skyworks' Total Power Management ICTM (TPMICTM) product family. It is a low dropout (LDO) linear regulator and a step-down converter with an input voltage range of 2.7V to 5.5V, making it ideal for applications with single lithium-ion/polymer batteries. The LDO has an independent input and is capable of delivering up to 300mA. The linear regulator has been designed for high-speed turn-on and turn-off performance, fast transient response, and good power supply rejection ratio (PSRR). Other features include low quiescent current and a low dropout voltage. The 400mA step-down converter is designed to minimize external component size and cost while maintaining a low 25A no load quiescent current. Peak current mode control with internal compensation provides a stable converter with a low equivalent series resistance (ESR) ceramic output capacitor for extremely low output ripple. For maximum battery life, the step-down converter increases to 100% duty cycle and has a typical 180mV dropout voltage at 400mA. The output voltage is either fixed or adjustable with an integrated P- and N-channel MOSFET power stage and 1MHz switching frequency. VIN Range: 2.7V to 5.5V 300mA LDO Current Output 400mV LDO Dropout Voltage at 300mA High Output Accuracy: 1.5% Fast LDO Line / Load Transient Response 400mA, 96% Efficiency Step-Down Converter 25A No Load Quiescent Current for Step-Down Converter Shutdown Current <1A Low RDS(ON) 0.4 Integrated Power Switches Low Dropout 100% Duty Cycle 1MHz Switching Frequency Internal Soft Start Over-Temperature Protection Current Limit Protection Available in TDFN33-12 Package -40C to +85C Temperature Range Applications Cellular Phones Digital Cameras Handheld Instruments Microprocessor/DSP Core/IO Power PDAs and Handheld Computers Portable Media Players The AAT2500 is available in a 12-pin TDFN33 package, and is rated over a temperature range of -40C to +85C. Typical Application VIN = 2.7V to 5.5V AAT2500 Step-Down Converter Efficiency 3 5 3.3V at 300mA 9 6 7 8 C4 2.2F C5 VP VCC VLDO EN ENLDO LX OUT FB BYP SGND GND PGND 4 100 10 L1 2 4.7H 11 12 1 U1 AAT2500 10nF L1 Sumida CDRH3D16-4R7 C1 Murata GRM219R61A475KE19 C3 Murata GRM21BR60J106KE19 C1 4.7F 2.5V 95 2.5V at 400mA Efficiency (%) C3 10F 90 1.8V 85 80 75 70 65 60 0.1 VIN = 3.3V 1 10 100 1000 Load Current (mA) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 1 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Pin Descriptions Pin # Symbol 1 PGND 2 3 4 5 6 LX VP VCC VLDO OUT 7 BYP 8 9 10 GND ENLDO EN 11 FB 12 SGND EP Function Step-down converter power ground return pin. Connect to the output and input capacitor return. See section on PCB layout guidelines and evaluation board layout diagram. Power switching node. Output switching node that connects to the output inductor. Step-down converter power stage supply voltage. Must be closely decoupled to PGND. Step-down converter bias supply. Connect to VP. LDO input voltage; should be decoupled with 1F or greater capacitor. 300mA LDO output pin. A 2.2F or greater output low-ESR ceramic capacitor is required for stability. Bypass capacitor for the LDO. To improve AC ripple rejection, connect a 10nF capacitor to GND. This will also provide a soft-start function. LDO ground connection pin. Enable pin for LDO. When connected low, LDO is disabled and consumes less than 1A of current. Step-down converter enable. When connected low, LDO is disabled and consumes less than 1A. Step-down converter feedback input pin. For fixed output voltage versions, this pin is connected to the converter output, forcing the converter to regulate to the specific voltage. For adjustable output versions, an external resistive divider ties to this point and programs the output voltage to the desired value. Step-down converter signal ground. For external feedback, return the feedback resistive divider to this ground. For internal fixed version, tie to the point of load return. See section on PCB layout guidelines and evaluation board layout diagram. Exposed paddle (bottom). Use properly sized vias for thermal coupling to the ground plane. See section on PCB layout guidelines. Pin Configuration TDFN33-12 (Top View) PGND LX VP VCC VLDO OUT 2 1 12 2 11 3 10 4 9 5 8 6 7 SGND FB EN ENLDO GND BYP Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Absolute Maximum Ratings1 Symbol VP, VLDO VLX VFB VEN TJ TLEAD Description Input Voltages to GND LX to GND FB to GND EN to GND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value Units 6.0 -0.3 to VP + 0.3 -0.3 to VP + 0.3 -0.3 to 6.0 -40 to 150 300 V V V V C C Value Units 2 50 W C/W Thermal Information Symbol PD JA Description Maximum Power Dissipation Thermal Resistance2 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 board with exposed paddle connected to ground plane. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 3 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Electrical Characteristics1 VIN = VLDO = VOUT(NOM) + 1V for VOUT options greater than 1.5V. VIN = VLDO = 2.5V for VOUT 1.5V. IOUT = 1mA, COUT = 2.2F, CIN = 1F, TA = -40C to +85C, unless otherwise noted. Typical values are TA = 25C. Symbol Description Conditions VOUT Output Voltage Tolerance IOUT = 1mA to 300mA VIN Input Voltage Min Typ Max Units LDO TA = 25C TA = -40C to 85C VDO VOUT/ VOUT*VIN Dropout Voltage IOUT = 300mA Line Regulation VIN = VOUT + 1V to 5V VOUT(Line) Dynamic Line Regulation VOUT(Load) IOUT ISC IQLDO Dynamic Load Regulation Output Current Short-Circuit Current LDO Quiescent Current 3, 4 ISHDN Shutdown Current PSRR Power Supply Rejection Ratio TSD THYS eN TC Over-Temperature Shutdown Threshold Over-Temperature Shutdown Hysteresis Output Noise Output Voltage Temperature Coefficient IOUT = 300mA, VIN = VOUT + 1V to VOUT + 2V, TR/TF = 2s IOUT = 1mA to 300mA, TR <5s VOUT > 1.3V VOUT < 0.4V VIN = 5V, No Load, ENLDO = VIN VIN = 5V; ENLDO = GND, EN = SGND = PGND 1kHz IOUT = 10mA, 10kHz CBYP = 10nF 1MHz eNBW = 300Hz to 50kHz -1.5 1.5 -2.5 2.5 VOUT + VDO2 5.5 V 600 mV 0.09 %/V 400 % 2.5 mV 60 125 mV mA mA A 1.0 A 300 600 70 67 47 45 145 12 50 22 dB C C VRMS ppm/C 1. The AAT2500 is guaranteed to meet performance specifications over the -40C to +85C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. To calculate the minimum LDO input voltage, use the following equation: VIN(MIN) = VOUT(MAX) + VDO(MAX), as long as VIN 2.5V. 3. For VOUT <2.1V, VDO = 2.5 - VOUT. 4. VDO is defined as VIN - VOUT when VOUT is 98% of nominal. 4 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Electrical Characteristics1 Typical values are TA = 25C, VIN = VCC = Vp = 3.6V. Symbol Description Conditions Buck Converter VIN Input Voltage VUVLO UVLO Threshold VOUT Output Voltage Tolerance VOUT Output Voltage Range IQBUCK Step-Down Converter Quiescent Current ISHDN Shutdown Current ILIM P-Channel Current Limit RDS(ON)H High Side Switch On Resistance Low Side Switch On Resistance RDS(ON)L ILXLK LX Leakage Current VLinereg Line Regulation VFB FB Threshold Voltage Accuracy FB Leakage Current IFB RFB FB Impedance FOSC Oscillator Frequency TSD Over-Temperature Shutdown Threshold THYS Over-Temperature Shutdown Hysteresis Logic Signals VEN(L) Enable Threshold Low VEN(H) Enable Threshold High IEN(H) Leakage Current Min Typ Max Units 5.5 2.6 V V mV V % 2.7 VIN Rising Hysteresis VIN Falling IOUT = 0 to 400mA, VIN = 2.7V to 5.5V Fixed Output Version Adjustable Output Version2 ENLDO = GND, No Load, 0.6V Adjustable Model EN = SGND = PGND, ENLDO = GND 100 1.8 -3.0 0.6 0.6 25 +3.0 4.0 2.5 50 1.0 600 0.45 0.4 VIN = 5.5V, VLX = 0 - VIN, EN = SGND = PGND VIN = 2.7V to 5.5V 0.6V Output, No Load, TA = 25C 0.6V Output >0.6V Output TA = 25C 597 250 0.7 600 1.0 140 15 1.0 0.2 615 0.2 1.5 0.6 1.5 1.0 1.0 V A A mA A %/V mV A k MHz C C V V A 1. The AAT2500 is guaranteed to meet performance specifications over the -40C to +85C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. For adjustable version with higher than 2.5V output, please consult your Skyworks representative. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 5 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. LDO Dropout Voltage vs. Temperature LDO Dropout Characteristics (EN = GND; ENLDO = VIN) (EN = GND; ENLDO = VIN) 3.20 IL = 300mA 480 Output Voltage (V) Dropout Voltage (mV) 540 420 360 300 IL = 100mA IL = 150mA 240 180 120 60 -40 -30 -20 -10 0 IOUT = 0mA 2.80 IOUT = 300mA IOUT = 150mA 2.60 2.40 2.20 IL = 50mA 0 3.00 IOUT = 10mA 2.00 2.70 10 20 30 40 50 60 70 80 90 100 110 120 2.80 2.90 3.00 3.10 LDO Dropout Voltage vs. Output Current LDO Ground Current vs. Input Voltage (EN = GND; ENLDO = VIN) 90.00 Ground Current (A) 450 400 350 300 85C 250 200 25C 150 -40C 100 50 80.00 70.00 60.00 IOUT=300mA 50.00 IOUT=150mA IOUT=50mA 40.00 IOUT=0mA 30.00 IOUT=10mA 20.00 10.00 0 0 50 100 150 200 250 300 0.00 2 2.5 3 3.5 4 4.5 Input Voltage (V) Output Current (mA) LDO Output Voltage vs. Temperature LDO Initial Power-Up Response Time (EN = GND; ENLDO = VIN) (CBYP = 10nF; EN = GND; ENLDO = VIN) 1.203 VENLDO (5V/div) 1.202 Output Voltage (V) 3.30 Input Voltage (V) 500 1.201 1.200 1.199 1.198 1.197 1.196 -40 -30 -20 -10 0 10 20 30 40 50 60 Temperature (C) 6 3.20 Temperature (C) (EN = GND; ENLDO = VIN) Dropout Voltage (mV) IOUT = 100mA IOUT = 50mA 70 80 90 100 VOUT (1V/div) Time (400s/div) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 5 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C, VIN = VLDO = VCC = VP. LDO Turn-Off Response Time LDO Turn-On Time From Enable (VIN present) (CBYP = 10nF; EN = GND; ENLDO = VIN) (CBYP = 10nF; EN = GND; ENLDO = VIN) VENLDO = 5V/div VENLDO (5V/div) VOUT (1V/div) VIN = 4V VOUT = 1V/div Time (50s/div) Time (5s/div) LDO Line Transient Response LDO Load Transient Response (CBYP = 10nF; EN = GND; ENLDO = VIN) (CBYP = 10nF; EN = GND; ENLDO = VIN) Input Voltage (V) 3.03 2.85 VIN 4 3.02 3 3.01 2 3.00 VOUT 1 2.99 0 2.98 500 400 VOUT 2.80 300 2.75 200 2.70 100 2.65 0 IOUT 2.60 -100 Time (100s/div) LDO Self Noise (CBYP = 10nF; EN = GND; ENLDO = VIN) (EN = GND; ENLDO = VIN) 3.00 800 2.90 700 600 VOUT 2.70 500 2.60 400 2.50 300 2.40 2.30 200 100 IOUT 2.20 0 2.10 -100 Time (10s/div) Noise Amplitude (V/rtHz) LDO Load Transient Response 300mA Output Current (mA) Output Voltage (V) Time (100s/div) 2.80 Output Current (mA) 2.90 Output Voltage (V) 5 3.04 Output Voltage (V) 6 10 1 0.1 0.01 Band Power: 300Hz to 50kHz = 44.6Vrms 100Hz to 100kHz = 56.3Vrms 0.001 0.01 0.1 1 10 100 1000 10000 Frequency (kHz) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 7 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. LDO ENLDO vs. VIN Over-Current Protection (EN = GND; ENLDO = VIN) Output Current (mA) 1200 1.250 1.225 1000 1.200 800 VIH 1.175 600 1.150 400 1.125 VIL 1.100 200 1.075 0 1.050 2.5 -200 3.0 3.5 Time (50ms/div) Step-Down Converter Efficiency vs. Load 4.5 5.0 5.5 Step-Down Converter Load Regulation (VOUT = 2.5V; EN = VIN; ENLDO = GND) (VOUT = 2.5V; EN = VIN; ENLDO = GND) 100 2.0 VIN = 3.3V Output Error (%) VIN = 3.0V Efficiency (%) 4.0 Input Voltage (V) 90 VIN = 3.6V 80 70 1.0 VIN = 3.0V 0.0 VIN = 3.3V -1.0 VIN = 3.6V 60 0.1 -2.0 1.0 10 100 1000 0.1 1.0 Output Current (mA) Step-Down Converter Efficiency vs. Load Step-Down Converter DC Regulation (VOUT = 1.8V; EN = VIN; ENLDO = GND) (VOUT = 1.8V; EN = VIN; ENLDO = GND) 1000 2.0 Output Error (%) VIN = 3.6V VIN = 2.7V 90 Efficiency (%) 100 Output Current (mA) 100 80 VIN = 4.2V 70 60 50 1.0 VIN = 4.2V 0.0 VIN = 2.7V -1.0 VIN = 3.6V -2.0 0.1 1.0 10 Output Current (mA) 8 10 100 1000 0.1 1.0 10 100 Output Current (mA) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 1000 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. Step-Down Converter Frequency vs. Input Voltage Step-Down Converter Output Voltage Error vs. Temperature (VOUT = 1.8V; EN = VIN; ENLDO = GND) (VIN = 3.6V; VO = 1.5V; EN = VIN; ENLDO = GND) Frequency Variation (%) 1.0 2.0 Output Error (%) 0.5 0.0 -0.5 -1.0 -1.5 -2.0 1.0 0.0 -1.0 -2.0 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 -40 -20 0 Input Voltage (V) 40 60 80 100 Temperature (C) Step-Down Converter Switching Frequency vs. Temperature Step-Down Converter Input Current vs. Input Voltage (VIN = 3.6V; VO = 1.5V; EN = VIN; ENLDO = GND) (VO = 1.8V; EN = VIN; ENLDO = GND) 0.20 35 Input Current ( A) Frequency Variation (%) 20 0.10 0.00 -0.10 85C 30 25C 25 20 -40C -0.20 -40 15 -20 0 20 40 60 80 2.5 100 3.5 4.0 4.5 5.0 5.5 Temperature (C) Input Voltage (V) Step-Down Converter P-Channel RDS(ON) vs. Input Voltage Step-Down Converter N-Channel RDS(ON) vs. Input Voltage (EN = VIN; ENLDO = GND) 6.0 (EN = VIN; ENLDO = GND) 750 750 700 700 650 120C 650 100C RDS(ON) (m ) RDS(ON) (m ) 3.0 600 550 85C 500 450 25C 400 120C 100C 600 550 500 85C 450 400 350 25C 350 300 300 2.5 3.0 3.5 4.0 4.5 Input Voltage (V) 5.0 5.5 6.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Input Voltage (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 9 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. (30mA - 300mA; VIN = 3.6V; VOUT = 1.8V; C1 = 10 F; C4 = 100pF; EN = VIN; ENLDO = GND) 1.2 1.8 1.0 300mA 1.7 1.6 0.8 0.6 30mA 1.5 0.4 1.4 0.2 1.3 0.0 -0.2 1.2 1.4 0.1 0.0 1.2 300mA -0.1 -0.2 1.0 30mA 0.8 -0.3 0.6 -0.4 0.4 -0.5 0.2 -0.6 0.0 -0.7 -0.2 Time (25s/div) Time (25s/div) (VOUT = 1.8V @ 400mA; EN = VIN; ENLDO = GND) 1.2 1.8 1.0 300mA 0.8 1.6 0.6 30mA 1.5 0.4 1.4 0.2 1.3 0.0 1.2 -0.2 1.90 7.0 1.85 6.5 1.80 6.0 1.75 5.5 1.70 5.0 1.65 4.5 1.60 4.0 1.55 3.5 1.50 Time (25s/div) Step-Down Converter Soft Start (VOUT = 1.8V; EN = VIN; ENLDO = GND) (VIN = 3.6V; VOUT = 1.8V; 400mA; EN = VIN; ENLDO = GND) IOUT = 100mA Accuracy (%) -0.05 -0.1 IOUT = 10mA -0.15 -0.2 IOUT = 400mA -0.25 -0.3 -0.35 2.5 3.0 3.5 4.0 4.5 Input Voltage (V) 5.0 5.5 6.0 4.0 3.5 3.0 3.0 2.0 2.5 1.0 2.0 0.0 1.5 -1.0 1.0 -2.0 0.5 -3.0 0.0 -0.5 -4.0 Time (250s/div) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 Inductor Current (bottom) (A) 0 Enable and Output Voltage (top) (V) 0.1 10 3.0 Time (25s/div) Step-Down Converter Line Regulation 0.05 Input Voltage (bottom) (V) 1.4 1.9 Load and Inductor Current (200mA/div) (bottom) 2.0 Output Voltage (top) (V) Step-Down Converter Line Transient (30mA - 300mA; VIN = 3.6V; VOUT = 1.8V; C1 = 4.7F; EN = VIN; ENLDO = GND) Output Voltage (top) (V) Step-Down Converter Load Transient Response 1.7 Load and Inductor Current (200mA/div) (bottom) 1.4 1.9 Load and Inductor Current (200mA/div) (bottom) 2.0 Output Voltage (AC Coupled) (top) (V) Step-Down Converter Load Transient Response (30mA - 300mA; VIN = 3.6V; VOUT = 1.8V; C1 = 10 F; EN = VIN; ENLDO = GND) Output Voltage (top) (V) Step-Down Converter Load Transient Response DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. Step-Down Converter Output Ripple 40 0.9 20 0.8 0 0.7 -20 0.6 -40 0.5 -60 0.4 -80 0.3 -100 0.2 Inductor Current (bottom) (A) Output Voltage (AC Coupled) (top) (mV) (VIN = 3.6V; VOUT = 1.8V; 400mA; EN = VIN; ENLDO = GND) 0.1 -120 Time (250ns/div) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 11 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Functional Block Diagram VP VCC FB Error Amp. DH See Note LX Logic Voltage Reference Control Logic EN DL PGND SGND OUT VLDO Over-Current Protection Error Amp. Voltage Reference BYP ENLDO Fast Start Control GND Note: Internal resistor divider included for 1.2V versions. For low voltage versions, the feedback pin is tied directly to the error amplifier input. Functional Description The AAT2500 is a high performance power management IC comprised of a buck converter and a linear regulator. The buck converter is a high efficiency converter capable of delivering up to 400mA. Designed to operate at 1.0MHz, the converter requires only three external components (CIN, COUT, and LX) and is stable with a ceramic output capacitor. The linear regulator delivers 300mA and is also stable with ceramic capacitors. Linear Regulator The advanced circuit design of the linear regulator has been specifically optimized for very fast start-up and shutdown timing. This proprietary CMOS LDO has also been tailored for superior transient response character- 12 istics. These traits are particularly important for applications that require fast power supply timing. The high-speed turn-on capability is enabled through implementation of a fast-start control circuit, which accelerates the power-up behavior of fundamental control and feedback circuits within the LDO regulator. Fast turn-off time response is achieved by an active output pull-down circuit, which is enabled when the LDO regulator is placed in shutdown mode. This active fast shutdown circuit has no adverse effect on normal device operation. The LDO regulator output has been specifically optimized to function with low-cost, low-ESR ceramic capacitors; however, the design will allow for operation over a wide range of capacitor types. A bypass pin has been provided to allow the addition of an optional voltage reference bypass capacitor to reduce Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator output self noise and increase power supply ripple rejection. Device self noise and PSRR will be improved by the addition of a small ceramic capacitor in this pin. However, increased values of CBYPASS may slow down the LDO regulator turn-on time. The regulator comes with complete short-circuit and thermal protection. The combination of these two internal protection circuits gives a comprehensive safety system to guard against extreme adverse operating conditions. The regulator features an enable/disable function. This pin (ENLDO) is active high and is compatible with CMOS logic. To assure the LDO regulator will switch on, the ENLDO turn-on control level must be greater than 1.5V. The LDO regulator will go into the disable shutdown mode when the voltage on the EN pin falls below 0.6V. If the enable function is not needed in a specific application, it may be tied to VIN to keep the LDO regulator in a continuously on state. When the regulator is in shutdown mode, an internal 1.5k resistor is connected between OUT and GND. This is intended to discharge COUT when the LDO regulator is disabled. The internal 1.5K resistor has no adverse impact on device turn-on time. Step-Down Converter The AAT2500 buck is a constant frequency peak current mode PWM converter with internal compensation. It is designed to operate with an input voltage range of 2.7V to 5.5V. The output voltage ranges from 0.6V to the input voltage for the internally fixed version, and up to 2.5V for the externally adjustable version. The 0.6V fixed model shown in Figure 1 is also the adjustable version and is externally programmable with a resistive divider, as shown in Figure 2. The converter MOSFET power stage is sized for 400mA load capability with up to 96% efficiency. Light load efficiency exceeds 80% at a 500A load. Soft Start The AAT2500 soft-start control prevents output voltage overshoot and limits inrush current when either the input power or the enable input is applied. When pulled low, the enable input forces the converter into a low-power, nonswitching state with a bias current of less than 1A. Low Dropout Operation For conditions where the input voltage drops to the output voltage level, the converter duty cycle increases to 100%. As 100% duty cycle is approached, the minimum off-time initially forces the high side on-time to exceed the 1MHz clock cycle and reduce the effective switching frequency. Once the input drops below the level where the output can be regulated, the high side P-channel MOSFET is turned on continuously for 100% duty cycle. At 100% duty cycle, the output voltage tracks the input voltage minus the IR drop of the high side P-channel MOSFET RDS(ON). Low Supply The under-voltage lockout (UVLO) guarantees sufficient VIN bias and proper operation of all internal circuitry prior to activation. Fault Protection For overload conditions, the peak inductor current is limited. Thermal protection disables switching when the internal dissipation or ambient temperature becomes excessive. The junction over-temperature threshold is 140C with 15C of hysteresis. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 13 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator VIN VIN C3 10F 3 5 9 VOUTLDO 6 7 8 C4 4.7F VP VCC VLDO EN ENLDO LX OUT FB BYP GND C5 10nF SGND PGND 4 C3 10F 10 2 L1 5 VOUTBUCK 9 VOUTLDO 11 6 12 1 7 C1 4.7F U1 AAT2500 Figure 1: AAT2500 Fixed Output. Applications Information Linear Regulator Input and Output Capacitors An input capacitor is not required for basic operation of the linear regulator. However, if the AAT2500 is physically located more than three centimeters from an input power source, a CIN capacitor will be needed for stable operation. Typically, a 1F or larger capacitor is recommended for CIN in most applications. CIN should be located as closely to the device VIN pin as practically possible. An input capacitor greater than 1F will offer superior input line transient response and maximize power supply ripple rejection. Ceramic, tantalum, or aluminum electrolytic capacitors may be selected for CIN. There is no specific capacitor ESR requirement for CIN. However, for 300mA LDO regulator output operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. For proper load voltage regulation and operational stability, a capacitor is required between OUT and GND. The COUT capacitor connection to the LDO regulator ground pin should be made as directly as practically possible for maximum device performance. Since the regulator has been designed to function with very low ESR capacitors, ceramic capacitors in the 1.0F to 10F range are recommended for best performance. Applications utilizing the exceptionally low output noise and optimum power 14 3 8 C4 4.7F C5 10nF VP VCC VLDO EN ENLDO LX OUT FB BYP SGND GND PGND 4 10 2 VOUTBUCK L1 R1 11 12 1 U1 AAT2500 C8 100pF R2 59k C1 4.7F Figure 2: AAT2500 with Adjustable Step-Down Output and Enhanced Transient Response. supply ripple rejection should use 2.2F or greater for COUT. In low output current applications, where output load is less than 10mA, the minimum value for COUT can be as low as 0.47F. Equivalent Series Resistance ESR is a very important characteristic to consider when selecting a capacitor. ESR is the internal series resistance associated with a capacitor that includes lead resistance, internal connections, size and area, material composition, and ambient temperature. Typically, capacitor ESR is measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Bypass Capacitor and Low Noise Applications A bypass capacitor pin is provided to enhance the low noise characteristics of the LDO. The bypass capacitor is not necessary for operation; however, for best device performance, a small ceramic capacitor in the range of 470pF to 10nF should be placed between the bypass pin (BYP) and the device ground pin (GND). To practically realize the highest power supply ripple rejection and lowest output noise performance, it is critical that the capacitor connection between the BYP pin and GND pin be direct and PCB traces should be as short as possible. DC leakage on this pin can affect the LDO regulator output noise and voltage regulation performance. For this reason, the use of a low leakage, high quality ceramic (NPO or C0G type) or film capacitor is highly recommended. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Step-Down Converter Inductor Selection The step-down converter uses peak current mode control with slope compensation to maintain stability for duty cycles greater than 50%. The output inductor value must be selected so the inductor current down slope meets the internal slope compensation requirements. The internal slope compensation for the adjustable and low-voltage fixed versions of the AAT2500 is 0.24A/s. This equates to a slope compensation that is 75% of the inductor current down slope for a 1.5V output and 4.7H inductor. m= 0.75 * VO 0.75 * 1.5V A = = 0.24 L 4.7H s This is the internal slope compensation for the adjustable (0.6V) version or low-voltage fixed versions. When externally programming the 0.6V version to 1.5V, the calculated inductance is 7.5H. L= 0.75 * VO = m s 0.75 * VO 3 * VO A A 0.24A s s =3 * 1.5V = 4.5H A In this case, a standard 4.7H value is selected. Manufacturer's specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the saturation characteristics. The inductor should not show any appreciable saturation under normal load conditions. Some inductors may meet the peak and average current ratings yet result in excessive losses due to a high DCR. Always consider the losses associated with the DCR and its effect on the total converter efficiency when selecting an inductor. The 4.7H CDRH3D16 series inductor selected from Sumida has a 105m DCR and a 900mA DC current rating. At full load, the inductor DC loss is 17mW which gives a 2.8% loss in efficiency for a 400mA, 1.5V output. Input Capacitor Select a 4.7F to 10F X7R or X5R ceramic capacitor for the input. To estimate the required input capacitor size, determine the acceptable input ripple level (VPP) and solve for C. The calculated value varies with input voltage and is a maximum when VIN is double the output voltage. CIN = VOBUCK VOBUCK * 1 VIN VIN VPP - ESR * FS IOBUCK 1 VOBUCK V * 1 - OBUCK = for VIN = 2 * VOBUCK VIN VIN 4 CIN(MIN) = 1 VPP - ESR * 4 * FS IOBUCK Always examine the ceramic capacitor DC voltage coefficient characteristics when selecting the proper value. For example, the capacitance of a 10F, 6.3V, X5R ceramic capacitor with 5.0V DC applied is actually about 6F. The maximum input capacitor RMS current is: IRMS = IOBUCK * VOBUCK V * 1 - OBUCK VIN VIN The input capacitor RMS ripple current varies with the input and output voltage and will always be less than or equal to half of the total DC load current. VOBUCK VOBUCK * 1= VIN VIN D * (1 - D) = 0.52 = 1 2 for VIN = 2 x VOBUCK IRMS(MAX) = VOBUCK IOBUCK 2 V * 1 - OBUCK VIN appears in both the input voltThe term VIN age ripple and input capacitor RMS current equations and is a maximum when VOBUCK is twice VIN. This is why the input voltage ripple and the input capacitor RMS current ripple are a maximum at 50% duty cycle. The input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT2500. Low ESR/ESL X7R and X5R ceramic capacitors are ideal for this function. To minimize stray inductance, the capacitor should be placed as closely as possible to the IC. This keeps the high frequency content of the input current localized, minimizing EMI and input voltage ripple. The proper placement of the input capacitor (C2) can be seen in the evaluation board layout in Figure 3. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 15 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator A laboratory test set-up typically consists of two long wires running from the bench power supply to the evaluation board input voltage pins. The inductance of these wires, along with the low-ESR ceramic input capacitor, can create a high Q network that may affect converter performance. This problem often becomes apparent in the form of excessive ringing in the output voltage during load transients. Errors in the loop phase and gain measurements can also result. Since the inductance of a short PCB trace feeding the input voltage is significantly lower than the power leads from the bench power supply, most applications do not exhibit this problem. In applications where the input power source lead inductance cannot be reduced to a level that does not affect the converter performance, a high ESR tantalum or aluminum electrolytic should be placed in parallel with the low ESR, ESL bypass ceramic. This dampens the high Q network and stabilizes the system. Output Capacitor The output capacitor limits the output ripple and provides holdup during large load transitions. A 4.7F to 10F X5R or X7R ceramic capacitor typically provides sufficient bulk capacitance to stabilize the output during large load transitions and has the ESR and ESL characteristics necessary for low output ripple. The output voltage droop due to a load transient is dominated by the capacitance of the ceramic output capacitor. Figure 3: AAT2500 Evaluation Board Top Side. 16 During a step increase in load current, the ceramic output capacitor alone supplies the load current until the loop responds. Within two or three switching cycles, the loop responds and the inductor current increases to match the load current demand. The relationship of the output voltage droop during the three switching cycles to the output capacitance can be estimated by: COUT = 3 * ILOAD VDROOP * FS Once the average inductor current increases to the DC load level, the output voltage recovers. The above equation establishes a limit on the minimum value for the output capacitor with respect to load transients. The internal voltage loop compensation also limits the minimum output capacitor value to 4.7F. This is due to its effect on the loop crossover frequency (bandwidth), phase margin, and gain margin. Increased output capacitance will reduce the crossover frequency with greater phase margin. The maximum output capacitor RMS ripple current is given by: IRMS(MAX) = 1 VOUT * (VIN(MAX) - VOUT) L * F * VIN(MAX) 2* 3 * Dissipation due to the RMS current in the ceramic output capacitor ESR is typically minimal, resulting in less than a few degrees rise in hot-spot temperature. Figure 4: AAT2500 Evaluation Board Bottom Side. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Adjustable Output Resistor Selection For applications requiring an adjustable output voltage, the 0.6V version can be externally programmed. Resistors R1 and R2 of Figure 5 program the output to regulate at a voltage higher than 0.6V. To limit the bias current required for the external feedback resistor string while maintaining good noise immunity, the minimum suggested value for R2 is 59k. Although a larger value will further reduce quiescent current, it will also increase the impedance of the feedback node, making it more sensitive to external noise and interference. Table 1 summarizes the resistor values for various output voltages with R2 set to either 59k for good noise immunity or 221k for reduced no load input current. The adjustable version of the AAT2500, combined with an external feedforward capacitor (C8 in Figures 2 and 5), delivers enhanced transient response for extreme pulsed load applications. The addition of the feedforward capacitor typically requires a larger output capacitor C1 for stability. VOUT (V) R2 = 59k R1 (k) R2 = 221k R1 (k) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 75 113 150 187 221 261 301 332 442 464 523 715 VOUT 1.5V R1 = V -1 * R2 = 0.6V - 1 * 59k = 88.5k REF Table 1: Adjustable Resistor Values For Use With 0.6V Step-Down Converter. LX1 VOUTBUCK C7 0.01F C1 4.7F1 C2 10F L1 Table 3 VIN1 1 2 3 4 3 2 1 5 6 LDO Input C3 10F C9 n/a U1 AAT2500 PGND SGND LX FB VP EN VCC ENLDO IN GND OUT BYP C4 4.7F 12 11 R1 Table 3 R2 59k 10 9 8 7 C5 10nF GND C81 3 2 1 Buck Enable 3 2 1 LDO Enable GND VOUTLDO Figure 5: AAT2500 Evaluation Board Schematic. 1. For step-down converter, enhanced transient configuration C8 = 100pF and C1 = 10uF. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 17 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Thermal Calculations There are three types of losses associated with the AAT2500 step-down converter: switching losses, conduction losses, and quiescent current losses. Conduction losses are associated with the RDS(ON) characteristics of the power output switching devices. Switching losses are dominated by the gate charge of the power output switching devices. At full load, assuming continuous conduction mode (CCM), a simplified form of the step-down converter and LDO losses is given by: Given the total losses, the maximum junction temperature can be derived from the JA for the TDFN33-12 package which is 50C/W. TJ(MAX) = PTOTAL * JA + TAMB PCB Layout The following guidelines should be used to ensure a proper layout. 1. 2 PTOTAL = IOBUCK * (RDSON(HS) * VOBUCK + RDSON(LS) * [VIN - VOBUCK]) VIN 2. + (tsw * F * IOBUCK + IQBUCK + IQLDO) * VIN + IOLDO * (VIN - VOLDO) IQBUCK is the step-down converter quiescent current and IQLDO is the LDO quiescent current. The term tsw is used to estimate the full load step-down converter switching losses. For the condition where the buck converter is in dropout at 100% duty cycle, the total device dissipation reduces to: 3. 4. PTOTAL = IOBUCK2 * RDSON(HS) + IOLDO * (VIN - VOLDO) + (IQBUCK + IQLDO) * VIN Since RDS(ON), quiescent current, and switching losses all vary with input voltage, the total losses should be investigated over the complete input voltage range. 18 5. 6. The input capacitor C2 should connect as closely as possible to VP and PGND, as shown in Figure 4. The output capacitor and inductor should be connected as closely as possible. The connection of the inductor to the LX pin should also be as short as possible. The feedback trace should be separate from any power trace and connect as closely as possible to the load point. Sensing along a high-current load trace will degrade DC load regulation. If external feedback resistors are used, they should be placed as closely as possible to the FB pin. This prevents noise from being coupled into the high impedance feedback node. The resistance of the trace from the load return to GND should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal signal ground and the power ground. For good thermal coupling, PCB vias are required from the pad for the TDFN paddle to the ground plane. The via diameter should be 0.3mm to 0.33mm and positioned on a 1.2mm grid. The LDO bypass capacitor (C5) should be connected directly between Pins 7 (BYP) and 8 (GND). Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Step-Down Converter Design Example Specifications VOBUCK = 1.8V @ 400mA (adjustable using 0.6V version), Pulsed Load ILOAD = 300mA VOLDO = 3.3V @ 300mA VIN = 2.7V to 4.2V (3.6V nominal) FS = 1.0MHz TAMB = 85C 1.8V Buck Output Inductor L1 = 3 s s * VO2 = 3 * 1.8V = 5.4H (see Table 1) A A For Sumida inductor CDRH3D16, 4.7H, DCR = 105m. 1.8V VOBUCK VOBUCK 1.8V 1= 1= 218mA L1 F VIN 4.7H 1.0MHz 4.2V IL1 = IPKL1 = IOBUCK + IL1 = 0.4A + 0.11A = 0.51A 2 PL1 = IOBUCK2 DCR = 0.4A2 105m = 17mW 1.8V Output Capacitor VDROOP = 0.2V COUT = 3 * ILOAD 3 * 0.3A = = 4.5F VDROOP * FS 0.2V * 1MHz IRMS = (VOBUCK) * (VIN(MAX) - VOBUCK) 1 1.8V * (4.2V - 1.8V) * = 63mArms = L1 * F * VIN(MAX) 2 * 3 4.7H * 1.0MHz * 4.2V 2* 3 1 * Pesr = esr * IRMS2 = 5m * (63mA)2 = 20W Input Capacitor Input Ripple VPP = 25mV CIN = IRMS = 1 VPP - ESR * 4 * FS IOBUCK = 1 = 4.75F 25mV - 5m * 4 * 1MHz 0.4A IOBUCK = 0.2Arms 2 P = esr * IRMS2 = 5m * (0.2A)2 = 0.2mW Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 19 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator AAT2500 Losses PTOTAL = IOBUCK2 * (RDSON(HS) * VOBUCK + RDSON(LS) * [VIN - VOBUCK]) VIN + (tsw * F * IOBUCK + IQBUCK + IQLDO) * VIN + (VIN - VLDO) * ILDO = 0.42 * (0.725 * 1.8V + 0.7 * [4.2V - 1.8V]) 4.2V + (5ns * 1.0MHz * 0.4A + 50A +125A) * 4.2V + (4.2V - 3.3V) * 0.3A = 392mW TJ(MAX) = TAMB + JA * PLOSS = 85C + (50C/W) * 392mW = 105C 20 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator VOUT (V) Adjustable Version (0.6V device) R1 (k) R2 = 59k R1 (k) R2 = 221k1 L1 (H) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 75.0 113 150 187 221 261 301 332 442 464 523 715 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 or 6.8 10 VOUT (V) Fixed Version R1 (k) R2 Not Used L1 (H) 0.6-3.3V 0 4.7 Table 3: Evaluation Board Component Values. Manufacturer Part Number Inductance (H) Max DC Current (A) DCR () Size (mm) LxWxH Type Sumida Sumida Murata Murata Murata Coilcraft Coilcraft Coiltronics Coiltronics Coiltronics Coiltronics CDRH3D16-4R7 CDRH3D16-100 LQH32CN4R7M23 LQH32CN4R7M33 LQH32CN4R7M53 LPO6610-472 LPO3310-472 SDRC10-4R7 SDR10-4R7 SD3118-4R7 SD18-4R7 4.7 10 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 0.90 0.55 0.45 0.65 0.65 1.10 0.80 1.53 1.30 0.98 1.77 0.11 0.21 0.20 0.15 0.15 0.20 0.27 0.117 0.122 0.122 0.082 3.8x3.8x1.8 3.8x3.8x1.8 2.5x3.2x2.0 2.5x3.2x2.0 2.5x3.2x1.55 5.5x6.6x1.0 3.3x3.3x1.0 4.5x3.6x1.0 5.7x4.4x1.0 3.1x3.1x1.85 5.2x5.2x1.8 Shielded Shielded Non-Shielded Non-Shielded Non-Shielded 1mm 1mm 1mm Shielded 1mm Shielded Shielded Shielded Table 4: Typical Surface Mount Inductors. Manufacturer Part Number Value Voltage Temp. Co. Case Murata Murata Murata Murata GRM21BR61A475KA73L GRM18BR60J475KE19D GRM21BR60J106KE19 GRM21BR60J226ME39 4.7F 4.7F 10F 22F 10V 6.3V 6.3V 6.3V X5R X5R X5R X5R 0805 0603 0805 0805 Table 5: Surface Mount Capacitors. 1. For reduced quiescent current R2 = 221k. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 21 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Ordering Information Voltage Package Buck Converter LDO Marking1 Part Number (Tape and Reel)2 TDFN33-12 TDFN33-12 TDFN33-12 TDFN33-12 TDFN33-12 Adj - 0.6V Adj - 0.6V Adj - 0.6V Adj - 0.6V 1.8V 3.3V 3.0V 2.8V 1.8V 3.3V NZXYY NYXYY OAXYY ONXYY SHXYY AAT2500IWP-AW-T14 AAT2500IWP-AT-T14 AAT2500IWP-AQ-T14 AAT2500IWP-AI-T14 AAT2500IWP-IW T14 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04-0074. Legend 1. 2. 3. 4. Voltage Code Adjustable (0.6V) 0.9 1.2 1.5 1.8 1.9 2.5 2.6 2.7 2.8 2.85 2.9 3.0 3.3 4.2 A B E G I Y N O P Q R S T W C XYY = assembly and date code. Sample stock is generally held on part numbers listed in BOLD. Contact Sales for availability. Product not available for U.S. market. 22 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 DATA SHEET AAT2500 1MHz Step-Down Converter/LDO Regulator Package Information1 TDFN33-12 Index Area 0.40 0.05 0.1 REF C0.3 0.45 0.05 2.40 0.05 3.00 0.05 Detail "A" 3.00 0.05 1.70 0.05 Top View Bottom View 0.23 0.05 Pin 1 Indicator (optional) 0.05 0.05 0.23 0.05 0.75 0.05 Detail "A" Side View All dimensions in millimeters. 1. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Copyright (c) 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202014A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * June 4, 2012 23