4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SEP Series Standard radial lead type, Guaranteed at 105C for 3,000h Specifications Conditions Items Category temperature range Tolerance on rated capacitance Tangent of loss angle Leakage current 1 ESR Characteristics of impedance ratio at high temp. and low temp. 120Hz 120Hz After 2 minutes Based the value at 100KHz+20C 105C, 3,000h, Rated voltage applied (2.5V2,000h), (25V20V applied) Endurance 60C, 90 to 95%RH, 1,000h, No-applied voltage Damp heat (Steady state) Resistance to soldering heat Flow method (2605C X 10s) Marking : Polarity( ), Rated voltage, Rated capacitance (Purple) Lot.No., SEP Characteristics -55C to +105C M :20% Less than or equal to the value of Table9 Less than or equal to the value of Table9 Less than or equal to the value of Table9 Z / Z 20C 0.75 to 1.25 -55C 0.75 to 1.25 Z / Z 20C +105C C/C Within 20% tan 1.5 times or less than an initial standard ESR 1.5 times or less than an initial standard Leakage current Below an initial standard C/C Within 20% tan 1.5 times or less than an initial standard ESR 1.5 times or less than an initial standard Leakage current Below an initial standard (after voltage processing) C/C Within 5% tan Below an initial standard ESR Below an initial standard Leakage current Below an initial standard (after voltage processing) 1 In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or temperature derating voltage for 25V products for 120 minutes at 105C . Dimensions (unit : mm) d Size Code D+0.5max. F D Specificationsfor eachseries This is a radial lead type using conductive polymer based on the SVP series. Because of its improved heat-proof characteristics, the rated ripple current values are guaranteed at 105C. Furthermore, there is no need to apply a temperature-compensating coefficient. Lead free-flow is supported. 15min. L 4min. 19min. Size List RV SV F 6.8 10 22 33 39 47 56 68 82 100 120 150 180 220 270 330 470 560 680 820 1200 1500 2.5 3.3 4 5.2 Lmax. F d0.05 C6 6.3 6.0 0.45 E7 8.0 7.0 2.50.5 3.50.5 F8 10.0 8.0 5.00.5 0.50 E12 8.0 12.0 3.50.5 0.60 F13 10.0 13.0 5.00.5 0.60 RV : Rated voltage (SV) : Surge (room temperature) 6.3 10 16 20 25 8.2 11.5 18.4 23.0 25.0 C6 E7 C6 E7 F8 E12 C6 E7 F8 F8 C6 C6 E7 C6 F8,E12 E7 C6 E7 F8 E12 E7 E12 E7 F8 E12 F8 F8 E12 F8 E12 F13 F13 F13 F13 F13 For the minimum packing quantity, please refer to page 51. 34 F13 F13 0.45 4. SPECIFICATIONS FOR EACH SERIES Table9 SEP Series Characteristics List Size Code E7 F8 E12 Rated Voltage (V) 1 2 ESR 100kHz to 300kHz (m) (max.) Rated ripple current 100kHz (mArms) at 105C Tangent of loss angle (max.) Leakage current (A) (max.)2 25SEP6R8M 25 80 1200 0.10 170 20SEP22M 20 22 60 1450 0.10 220 16SEP39M 16 39 50 1620 0.10 312 10SEP56M 10 56 45 1700 0.12 280 82 45 1700 0.12 258 6.8 6SEP82M 6.3 4SEP100M 4 100 40 1810 0.12 200 4SEP150M 4 150 40 1810 0.12 300 25SEP10M 25 10 60 1500 0.10 250 20SEP33M 20 33 45 1890 0.12 330 20SEP47M 20 47 45 1890 0.12 470 16SEP82M 16 82 40 2120 0.12 656 10SEP120M 10 120 35 2560 0.12 600 6SEP150M 6.3 150 35 2560 0.12 472 4SEP220M 4 220 35 2560 0.12 440 4SEP330M 4 330 35 2560 0.12 660 25SEP22M 25 22 50 2000 0.10 275 20SEP56M 20 56 40 2400 0.12 224 20SEP68M 20 68 40 2400 0.12 272 20SEP100MX 20 100 35 2570 0.12 400 16SEP150M 16 150 30 3020 0.12 480 10SEP270M 10 270 25 3700 0.12 540 6SEP330M 6.3 330 25 3700 0.12 416 4SEP470M 4 470 25 3700 0.12 376 4SEP680M 4 680 25 3700 0.12 544 25SEP33M 25 33 30 2980 0.12 413 20SEP100M 20 100 24 3320 0.15 400 16SEP180M 16 180 20 3640 0.15 576 10SEP330M 10 330 17 3950 0.15 660 6.3 470 15 4210 0.15 592 4SEP560M 4 560 13 4520 0.15 448 2R5SEP680M 2.5 680 13 4520 0.15 340 6SEP470M F13 Rated Capacitance (F) 25SEP56M 25 56 28 3800 0.12 700 20SEP150M 20 150 20 4320 0.15 600 16SEP330M 16 330 16 4720 0.15 792 10SEP560M 10 560 13 5230 0.15 840 6SEP820M 6.3 820 12 5440 0.15 775 4SEP1200M 4 1200 12 5440 0.18 960 2R5SEP1500M 2.5 1500 12 5440 0.18 750 Specificationsfor eachseries C6 Part Number 1 Capacitance tolerance : M 20% After 2 minutes Frequency coefficient for ripple current Frequency Coefficient 120Hz f 1kHz 0.05 1kHz f 10kHz 0.3 10kHz f 100kHz 0.7 100kHz f 500kHz 1 35