■Size List
34
6.8
10
22
33
39
47
56
68
82
100
120
150
180
220
270
330
470
560
680
820
1200
1500
E12
F13
RV
(SV)
µF2.5
(3.3)4
(5.2)6.3
(8.2)10
(11.5)16
(18.4)20
(23.0)25
(25.0)
C6
C6
E7
E7
F8
E12
F8
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
E7
F8
F8
F8,E12
F13
C6
E7
F8
E12
F13
(unit : mm)
※1 In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or temperature derating
voltage for 25V products for 120 minutes at 105°C .
■Dimensions
RV : Rated voltage (SV) : Surge (room temperature)
※For the minimum packing quantity, please refer to page 51.
This is a radial lead type using conductive polymer based on the SVP
series.
Because of its improved heat-proof characteristics, the rated ripple current
values are guaranteed at 105
°C
. Furthermore, there is no need to apply a
temperature-compensating coefficient.
Lead free-flow is supported. Marking : Polarity( ), Rated voltage, Rated capacitance
(Purple) Lot.No., SEP
■Specifications
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
φd
L
F
15min.
19min.
φD
4min.
6.3
8.0
10.0
8.0
10.0
6.0
7.0
8.0
12.0
13.0
2.5±0.5
3.5±0.5
5.0±0.5
3.5±0.5
5.0±0.5
0.45
0.45
0.50
0.60
0.60
C6
E7
F8
E12
F13
Size Code
φD+0.5max.
Lmax. F φd
±
0.05
Conductive polymer type
SEPSeries Standard radial lead type,
Guaranteed at 105
°C
for 3,000h
(+)
Items Characteristics
-55°C to +105°C
M :±20%
Less than or equal to the value of Table9
Less than or equal to the value of Table9
Less than or equal to the value of Table9
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard (after voltage processing)
Within ±5%
Below an initial standard
Below an initial standard
Below an initial standard (after voltage processing)
Category temperature range
Tolerance on rated capacitance
Tangent of loss angle
Leakage current
ESR
Endurance
Damp heat (Steady state)
Characteristics of impedance
ratio at high temp. and low temp.
-55°C
+105°C
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Resistance to
soldering heat
Z / Z 20°C
Z / Z 20°C0.75 to 1.25
0.75 to 1.25
120Hz
120Hz
105°C, 3,000h, Rated
voltage applied
(2.5V→2,000h),
(25V→20V applied)
60°C, 90 to 95%RH,
1,000h,
No-applied voltage
Flow method
(260±5°C X 10s)
※1
Conditions
Based the value at
100KHz,+20°C
After 2 minutes