ISL97645 (R) Data Sheet December 14, 2007 Boost + VON Slice + VCOM Features The ISL97645 represents an integrated DC/DC regulator for monitor and notebook applications with screen sizes up to 20". The device integrates a boost converter for generating AVDD, a VON slice circuit, and a high performance VCOM amplifier. * 2.7V to 5.5V Input The boost converter features a 2.6A FET and has user programmable soft-start and compensation. With efficiencies up to 92%, the AVDD is user selectable from 7V to 20V. * VCOM Amplifier - 30MHz BW - 50V/s SR - 400mA Peak Output Current The VON slice circuit can control gate voltages up to 30V. High and low levels are programmable, as well as discharge rate and timing. The integrated VCOM features high speed and drive capability. With 30MHz bandwidth and 50V/s slew rate, the VCOM amplifier is capable of driving 400mA peaks, and 100mA continuous output current. FN9263.1 * 2.6A Integrated Boost for Up to 20V AVDD * Integrated VON Slice * 600kHz/1.2MHz fS * UV and OT Protection * 24 Ld 4x4 QFN * Pb-Free (RoHS Compliant) Applications * LCD Monitors (15"+) Pinout * Notebook Display (up to 16") ISL97645 (24 LD 4x4 QFN) TOP VIEW VGH RE CE PGND FB ENABLE Ordering Information 24 23 22 21 20 19 TEMP. RANGE PART NUMBER PART (C) (Note) MARKING PACKAGE (Pb-Free) PKG. DWG. # ISL97645IRZ 97645IRZ -40 to +85 24 Ld 4x4 QFN L24.4x4D ISL97645IRZ-T* 97645IRZ -40 to +85 24 Ld 4x4 QFN L24.4x4D 6k pc Tape & Reel 17 VIN VFLK 3 16 FREQ ISL97645IRZ-TK* 97645IRZ -40 to +85 24 Ld 4x4 QFN L24.4x4D 1k pc Tape & Reel VDPM 4 15 COMP *Please refer to TB347 for details on reel specifications. VDD_1 5 14 SS VDD_2 6 13 NC 7 8 9 1 10 11 12 NC 2 NC VGH_M AGND LX POS 18 NEG 1 OUT GND NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL97645 Pin Descriptions PIN NUMBER PIN NAME 1 GND 2 VGH_M 3 VFLK Gate Pulse Modulation Control Input 4 VDPM Gate Pulse Modulation Enable 5 VDD_1 Gate Pulse Modulation Lower Voltage Input 6 VDD_2 VCOM Amplifier Supply 7 OUT VCOM Amplifier Output 8 NEG VCOM Amplifier Inverting Input 9 POS VCOM Amplifier Noninverting Input 10 AGND 11 NC 12 NC 13 NC 14 SS 15 COMP Boost Converter Compensation Pin. Connect a series resistor and capacitor between this pin and GND to optimize transient response. 16 FREQ Boost Converter Frequency Select. 17 VIN Boost Converter Power Supply 18 LX Boost Converter Switching Node 19 ENABLE 20 FB 21 PGND 22 CE Gate Pulse Modulator Delay Control. Connect a capacitor between this pin and GND to set the delay time. 23 RE Gate Pulse Modulator Slew Control. Connect a resistor between this pin and GND to set the falling slew rate. 24 VGH 2 FUNCTION Ground Gate Pulse Modulation Output VCOM Amplifier Ground Boost Converter Soft-start. Connect a capacitor between this pin and GND to set the soft-start time. Chip Enable Pin. Connect to Vin for normal operation, GND for shutdown. Boost Converter Feedback Boost Converter Power Ground Gate Pulse Modulator High Voltage Input FN9263.1 December 14, 2007 ISL97645 Absolute Maximum Ratings Thermal Information Lx to GND, AGND and PGND . . . . . . . . . . . . . . . . . . . . -0.5 to +25V VDD2, OUT, NEG and POS to GND, AGND and PGND. . . . . . . . . . . . . . . . . . . . . -0.5 to +25V VDD1, VGH and VGH_M to GND, AGND and PGND. . . . . . . . . . . . . . . . . . . . . -0.5 to +32V Differential Voltage Between POS and NEG . . . . . . . . . . . . . . . 6V Voltage Between GND, AGND and PGND . . . . . . . . . . . . . . . 0.5V All Other Pins to GND, AGND and PGND . . . . . . . . . . -0.5 to +6.5V Input, Output, or I/O Voltage . . . . . . . . . . . GND -0.3V to VIN + 0.3V Thermal Resistance Recommended Operating Conditions Input Voltage Range, VS . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Boost Output Voltage Range, AVDD . . . . . . . . . . . . . . . . . 8V to 20V Input Capacitance, CIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22F Boost Inductor, L1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3H to 10H Output Capacitance, COUT . . . . . . . . . . . . . . . . . . . . . . . . . . 2x22F Operating Ambient Temperature Range . . . . . . . . . .-40C to +85C Operating Junction Temperature . . . . . . . . . . . . . . .-40C to +125C JA (C/W) JC (C/W) 4x4 QFN Package (Notes 1, 2) . . . . . . 39 2.5 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Maximum Continuous Junction Temperature . . . . . . . . . . . +125C Power Dissipation TA +25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.44W TA = +70C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.34W TA = +85C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.98W TA = +100C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.61W Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. 2. For JC, the "case temp" location is the center of the exposed metal pad on the package underside. Electrical Specifications SYMBOL VIN = ENABLE = 5V, VDD1 = VDD2 = 14V, VGH = 25V, AVDD = 10V, TA = -40C to +85C Unless Otherwise Noted. PARAMETER TEST CONDITION MIN TYP MAX UNIT 2.7 3.3 5.5 V 0.2 2 A GENERAL VS VINInput Voltage Range IS_DIS VIN Supply Currents when Disabled ENABLE = 0V IS VIN Supply Currents ENABLE = 5V, LX not switching UVLO Undervoltage Lockout Threshold VIN2 Rising 2.3 2.45 2.6 V VIN2 Falling 2.2 2.35 2.5 V OTR Thermal Shutdown Temperature OTF 1 mA Temperature Rising 140 C Temperature Falling 100 C LOGIC INPUT CHARACTERISTICS - ENABLE, VFLK, FREQ, VDPM VIL Low Voltage Threshold VIH High Voltage Threshold RIL Pull-Down Resistor 0.8 2.2 Enabled, Input at Vin 150 V V 250 400 k 20 V STEP-UP SWITCHING REGULATOR AVDD Output Voltage Range AVDD/IOUT Load Regulation 50mA < ILOAD < 250mA 0.2 AVDD/VIN Line Regulation ILOAD = 150mA, 3.0 < VIN < 5.5V 0.15 ACCAVDD Overall Accuracy (Line, Load, Temperature) 10mA < ILOAD < 300mA, 3.0 < Vin < 5.5V, 0C < TA < +85C VFB Feedback Voltage (VFB) ILOAD = 100mA, TA = +25C 1.20 ILOAD = 100mA, TA = -40C to +85C 1.19 3 VIN*1.25 % 0.25 %/V 3 % 1.21 1.22 V 1.21 1.23 V -3 FN9263.1 December 14, 2007 ISL97645 Electrical Specifications SYMBOL VIN = ENABLE = 5V, VDD1 = VDD2 = 14V, VGH = 25V, AVDD = 10V, TA = -40C to +85C Unless Otherwise Noted. (Continued) PARAMETER TEST CONDITION MIN TYP MAX UNIT IFB FB Input Bias Current 250 500 nA RDS(ON) Switch On Resistance 150 300 m EFF Peak Efficiency 92 % ILIM Switch Current Limit 2.1 2.6 A DMAX Max Duty Cycle 85 90 % FOSC Oscillator Frequency FREQ = 0V 550 650 800 kHz FREQ = VIN2 1.0 1.2 1.4 MHz ISS Soft-Start Slew Current SS < 1V, TA = +25C 2.75 A VCOM AMPLIFIER RLOAD = 10k, CLOAD = 10pF, Unless Otherwise Stated VSAMP Supply Voltage 4.5 ISAMP Supply Current 3 VOS Offset Voltage 3 20 mV IB Noninverting Input Bias Current 0 100 nA CMIR Common Mode Input Voltage Range 0 VDD2 V CMRR Common-Mode Rejection Ratio 50 70 dB PSRR Power Supply Rejection Ratio 70 85 dB VOH Output Voltage Swing High Iout(source) = 5mA VDD2 - 50 mV VOH Output Voltage Swing High Iout(source) = 50mA VDD2 - 450 mV VOL Output Voltage Swing Low Iout(sink) = 5mA 50 mV VOL Output Voltage Swing Low Iout(sink) = 50mA 450 mV ISC Output Short Circuit Current 400 mA SR Slew Rate 50 V/s BW Gain Bandwidth 30 MHz 250 -3dB gain point 20 V mA GATE PULSE MODULATOR VGH VGH Voltage 7 IVGH VGH Input Current 30 V VFLK = 0 260 A RE = 33k, VFLK = VDD1 40 A VDD1 VDD1 Voltage 3 IVDD1 VDD1 Input Current -2 RONVGH VGH to VGH_M On Resistance 70 IDIS_VGH VGH_M Discharge Current (Note 1) RE = 33k 8 mA TDEL DELAY Time (Note 2) 1.9 s CE = 470pF, RE = 33k 0.1 VGH - 2 V 2 A NOTES: 1. Nominal discharge current = 300/(RE+5k). 2. Nominal delay time = 4000*CE. 4 FN9263.1 December 14, 2007 ISL97645 I Typical Performance Curves 100 0 FOSC = 650kHz 90 -0.1 EFFICIENCY (%) LOAD REGULATION (%) FOSC = 1.2MHz 80 70 60 50 40 30 20 -0.3 FOSC = 650kHz -0.4 -0.5 FOSC = 1.2MHz -0.6 -0.7 -0.8 10 0 -0.2 0 200 400 600 800 IAVDD (mA) 1000 1200 FIGURE 1. AVDD EFFICIENCY vs IAVDD -0.9 0 200 400 600 800 IAVDD (mA) 1000 1200 FIGURE 2. AVDD LOAD REGULATION vs IAVDD 10.5 L = 10H, COUT = 40F, CCOMP = 2.2nF, RCOMP = 10k 10.45 AVDD 150mA IAVDD AVDD (V) 10.4 AVDD 500mA 10.35 10.3 10.25 AVDD (AC COUPLED) 10.2 10.15 3 3.5 4.0 4.5 5.0 5.5 6.0 VIN (V) FIGURE 3. LINE REGULATION AVDD vs VIN FIGURE 4. BOOST CONVERTER TRANSIENT RESPONSE CE = 1pF, RE = 100k VGH_M CE = 1000pF, RE = 100k VGH_M VFLK VFLK FIGURE 5. GPM CIRCUIT WAVEFORM 5 FIGURE 6. GPM CIRCUIT WAVEFORM FN9263.1 December 14, 2007 ISL97645 Typical Performance Curves (Continued) CE = 10pF, RE = 100k CE = 10pF, RE = 150k VGH_M VGH_M VFLK VFLK FIGURE 7. GPM CIRCUIT WAVEFORM FIGURE 8. GPM CIRCUIT WAVEFORM INPUT SIGNAL INPUT SIGNAL OUTPUT SIGNAL OUTPUT SIGNAL (-3dB ATTENTUATION FROM INPUT SIGNAL) FIGURE 9. VCOM RISING SLEW RATE 6 FIGURE 10. VCOM BANDWIDTH MEASUREMENT FN9263.1 December 14, 2007 ISL97645 Block Diagram LX FREQ OSCILLATION GENERATOR SLOPE COMPENSATION COMP FB SUMMING AMPLIFIER + PWM LOGIC + 2.5A PGND SS REFERENCE GENERATOR VIN START-UP AND FAULT CONTROL VDPM ENABLE NC NC VDD2 POS + - OUT NEG GND GPM CIRCUIT VFLK VGH VGH_M CE VDD1 RE FIGURE 11. ISL97645 BLOCK DIAGRAM 7 FN9263.1 December 14, 2007 ISL97645 Typical Application Diagram L1 10H VIN D1 LX C1 22F C3 2.2nF COMP BOOST AVDD C2 47F R1 10K FB C4 10nF SS R2 1.3K PGND S1 ENABLE S2 FREQV ON VGH S3 VDPM VFLK C5 470P CE VDD_1 GPM CIRCUIT VGH_M VDD2 RE R6 130k AVDD R7 80k R3 2K TO ROW DRIVER 0.47F POS C11 1F NEGOUT VCOM +4.0V VIN C6 0.1F NC AGND GND NC FIGURE 12. TYPICAL APPLICATION DIAGRAM Applications Information The ISL97645 provides a complete power solution for TFT LCD applications. The system consists of one boost converter to generate AVDD voltage for column drivers, one integrated VCOM buffer which can provide up to 400mA peak current. This part also integrates Gate Pulse Modulator circuit that can help to optimize the picture quality. Enable Control When enable pin is pulling down, the ISL97645 is shut down reducing the supply current to <10A. When the voltage at enable pin reaches 2.2V, the ISL97645 is on. Boost Converter switching frequency can save power dissipation, while higher switching frequency can allow smaller external components like inductor and output capacitors, etc. Connecting FREQ pin to ground sets the PWM switching frequency to 650MHz, or connecting FREQ pin to VIN for 1.2MHz. Soft-Start The soft-start is provided by an internal 2.5A current source to charge the external soft start capacitor. The ISL97645 ramps up current limit from 0A up to full value, as the voltage at SS pin ramps from 0 to 1.2V. Hence the soft-start time is 4.8ms when the soft-start capacitor is 10nF, 22.6ms for 47nF and 48ms for 100nF. Operation Frequency Selection The ISL97645 switching frequency can be user selected to operate at either constant 650kHz or 1.2MHz. Lower 8 The boost converter is a current mode PWM converter operating at either a 650kHz or 1.2MHz. It can operate in both discontinuous conduction mode (DCM) at light load and FN9263.1 December 14, 2007 ISL97645 continuous mode (CCM). In continuous current mode, current flows continuously in the inductor during the entire switching cycle in steady state operation. The voltage conversion ratio in continuous current mode is given by: V Boost 1 ------------------- = ------------1-D V IN This restricts the maximum output current (average) based on the following equation: I L V IN I OMAX = I LMT - -------- x -------- 2 VO (EQ. 3) Where IL is peak to peak inductor ripple current, and is set by: (EQ. 1) Where D is the duty cycle of the switching MOSFET. V IN D I L = --------- x ---L fs Figure 11 shows the block diagram of the boost regulator. It uses a summing amplifier architecture consisting of gm stages for voltage feedback, current feedback and slope compensation. A comparator looks at the peak inductor current cycle by cycle and terminates the PWM cycle if the current limit is reached. where fS is the switching frequency (650kHz or 1.2MHz). The Table 2 gives typical values (margins are considered 10%, 3%, 20%, 10% and 15% on VIN, VO, L, fS and IOMAX). Capacitor An external resistor divider is required to divide the output voltage down to the nominal reference voltage. Current drawn by the resistor network should be limited to maintain the overall converter efficiency. The maximum value of the resistor network is limited by the feedback input bias current and the potential for noise being coupled into the feedback pin. A resistor network in the order of 60k is recommended. The boost converter output voltage is determined by the following equation: R1 + R2 V Boost = --------------------- x V FB R2 (EQ. 4) An input capacitor is used to suppress the voltage ripple injected into the boost converter. The ceramic capacitor with capacitance larger than 10F is recommended. The voltage rating of input capacitor should be larger than the maximum input voltage. Some capacitors are recommended in Table 1 for input capacitor. TABLE 1. BOOST CONVERTER INPUT CAPACITOR RECOMMENDATION CAPACITOR (EQ. 2) The current through the MOSFET is limited to 2.6APEAK. SIZE MFG PART NUMBER 10F/16V 1206 TDK C3216X7R1C106M 10F/10V 0805 Murata GRM21BR61A106K 22F/10V 1210 Murata GRB32ER61A226K TABLE 2. MAXIMUM OUTPUT CURRENT CALCULATION VIN (V) VO (V) L (H) Fs (MHz) IOMAX (mA) 3 9 10 0.65 636 3 12 10 0.65 419 3 15 10 0.65 289 5 9 10 0.65 1060 5 12 10 0.65 699 5 15 10 0.65 482 5 18 10 0.65 338 3 9 10 1.2 742 3 12 10 1.2 525 3 15 10 1.2 395 5 9 10 1.2 1236 5 12 10 1.2 875 5 15 10 1.2 658 5 18 10 1.2 514 9 FN9263.1 December 14, 2007 ISL97645 Inductor The boost inductor is a critical part which influences the output voltage ripple, transient response, and efficiency. Values of 3.3H to 10H are used to match the internal slope compensation. The inductor must be able to handle the following average and peak current: IO I LAVG = ------------1-D I L I LPK = I LAVG + -------2 The following table shows some selections of output capacitors. TABLE 3. BOOST INDUCTOR RECOMMENDATION MFG PART NUMBER 7.3x6.8x3.2 TDK RLF7030T-6R8N3R0 10H/4APEAK 8.3x8.3x4.5 Sumida CDR8D43-100NC 5.2H/4.55APEAK 10x10.1x3.8 TABLE 5. BOOST OUTPUT CAPACITOR RECOMMENDATION CAPACITOR DIMENSIONS (mm) 6.8H/3APEAK SIZE MFG PART NUMBER 10F/25V 1210 TDK C3225X7R1E106M 10F/25V 1210 Murata GRM32DR61E106K Compensation Cooper CD1-5R2 Bussmann Rectifier Diode A high-speed diode is necessary due to the high switching frequency. Schottky diodes are recommended because of their fast recovery time and low forward voltage. The reverse voltage rating of this diode should be higher than the maximum output voltage. The rectifier diode must meet the output current and peak inductor current requirements. The following table is some recommendations for boost converter diode. TABLE 4. BOOST CONVERTER RECTIFIER DIODE RECOMMENDATION DIODE Note: Capacitors have a voltage coefficient that makes their effective capacitance drop as the voltage across then increases. COUT in the equation above assumes the effective value of the capacitor at a particular voltage and not the manufacturer's stated value, measured at zero volts. (EQ. 5) Some inductors are recommended in Table 3. INDUCTOR For low ESR ceramic capacitors, the output ripple is dominated by the charging and discharging of the output capacitor. The voltage rating of the output capacitor should be greater than the maximum output voltage. VR/IAVG RATING PACKAGE SS23 30V/2A SMB Fairchild Semiconductor MBRS340 40V/3A SMC International Rectifier SL23 30V/2A SMB Vishay Semiconductor MFG The boost converter of ISL97645 can be compensated by a RC network connected from CM1 pin to ground. 4.7nF and 10k RC network is used in the demo board. The larger value resistor and lower value capacitor can lower the transient overshoot, however, at the expense of stability of the loop. Cascaded MOSFET Application An 20V N-channel MOSFET is integrated in the boost regulator. For the applications where the output voltage is greater than 20V, an external cascaded MOSFET is needed as shown in Figure 13. The voltage rating of the external MOSFET should be greater than AVDD. AVDD VIN LX FB Intersil ISL97645 Output Capacitor The output capacitor supplies the load directly and reduces the ripple voltage at the output. Output ripple voltage consists of two components: the voltage drop due to the inductor ripple current flowing through the ESR of output capacitor, and the charging and discharging of the output capacitor. IO V O - V IN 1 V RIPPLE = I LPK x ESR + ------------------------ x ---------------- x ---C f V O 10 OUT s FIGURE 13. CASCADED MOSFET TOPOLOGY FOR HIGH OUTPUT VOLTAGE APPLICATIONS (EQ. 6) FN9263.1 December 14, 2007 ISL97645 Gate Pulse Modulator Circuit The gate pulse modulator circuit functions as a three way multiplexer, switching VGHM between ground, VDD1 and VGH. Voltage selection is provided by digital inputs VDPM (enable) and VFLK (control). High to low delay and slew control is provided by external components on pins CE and RE, respectively. A block diagram of the gate pulse modulator circuit is shown in Figure 14. When VDPM is LOW, the block is disabled and VGHM is grounded. When VDPM is HIGH, the output is determined by VFLK. When VFLK goes high, VGHM is pulled to VGH by a 70 switch. When VFLK goes low, there is a delay controlled by capacitor CE, following which VGHM is driven to VDD1, with a slew rate controlled by resistor RE. Note that VDD1 is used only as a reference voltage for an amplifier, thus does not have to source or sink a significant DC current. VGH VGH_M EnGPM1 + VDD1 - x240 VREF + RE 200A VFLK - + CE CONTROL AND TIMING FIGURE 14. GATE PULSE MODULATOR CIRCUIT BLOCK DIAGRAM 11 FN9263.1 December 14, 2007 ISL97645 Low to high transition is determined primarily by the switch resistance and the external capacitive load. High to low transition is more complex. Take the case where the block is already enabled (VDPM is H). When VFLK is H, pin CE is grounded. On the falling edge of VFLK, a current is passed into pin CE, to charge an external capacitor to 1.2V. This creates a delay, equal to CE*4200. At this point, the output begins to pull down from VGH to VDD1. The slew current is equal to 300/(RE+5000)*Load Capacitance. VDPM the following circuit can be inserted between input and inductor to disconnect the DC path when the part is disabled. TO INDUCTOR INPUT ENABLE FIGURE 17. CIRCUIT TO DISCONNECT THE DC PATH OF BOOST CONVERTER 0 VFLK SLOPE CONTROLLED BY RE AND LOAD CAPACITANCE 0 VGH VGH_M VDD_1 0 DELAY TIME CONTROLLED BY CE FIGURE 15. GATE PULSE MODULATOR TIMING DIAGRAM Start-Up Sequence Figure 16 shows a detailed start-up sequence waveform. VIN 0 ENABLE 0 VDPM VIN THRESHOLD VCOM Amplifier The VCOM amplifier is designed to control the voltage on the back plate of an LCD display. This plate is capacitively coupled to the pixel drive voltage which alternately cycles positive and negative at the line rate for the display. Thus the amplifier must be capable of sourcing and sinking capacitive pulses of current, which can occasionally be quite large (a few 100mA for typical applications). The ISL97645 VCOM amplifier's output current is limited to 400mA. This limit level, which is roughly the same for sourcing and sinking, is included to maintain reliable operation of the part. It does not necessarily prevent a large temperature rise if the current is maintained. (In this case the whole chip may be shut down by the thermal trip to protect functionality.) If the display occasionally demands current pulses higher than this limit, the reservoir capacitor will provide the excess and the amplifier will top the reservoir capacitor back up once the pulse has stopped. This will happen on the s time scale in practical systems and for pulses 2 or 3 times the current limit, the VCOM voltage will have settled again before the next line is processed. Fault Protection 0 ISL97645 provides the overall fault protections including over current protection and over-temperature protection. AVDD VGH_M 0 FIGURE 16. START-UP SEQUENCE An internal temperature sensor continuously monitors the die temperature. In the event that die temperature exceeds the thermal trip point, the device will shut down and disable itself. The upper and lower trip points are typically set to +140C and +100C respectively. When VIN exceeds 2.5V and ENABLE reaches the VIH threshold value, Boost converter starts up, and gate pulse modulator circuit output holds until VDPM goes to high. Note that there is a DC path in the boost converter from the input to the output through the inductor and diode, hence the input voltage will be seen at output with a forward voltage drop of diode before the part is enabled. If this voltage is not desired, 12 FN9263.1 December 14, 2007 ISL97645 Layout Recommendation The device's performance including efficiency, output noise, transient response and control loop stability is dramatically affected by the PCB layout. PCB layout is critical, especially at high switching frequency. There are some general guidelines for layout: 1. Place the external power components (the input capacitors, output capacitors, boost inductor and output diodes, etc.) in close proximity to the device. Traces to these components should be kept as short and wide as possible to minimize parasitic inductance and resistance. 2. Place VIN and VDD bypass capacitors close to the pins. 3. Reduce the loop area with large AC amplitudes and fast slew rate. 4. The feedback network should sense the output voltage directly from the point of load, and be as far away from LX node as possible. 5. The power ground (PGND) and signal ground (SGND) pins should be connected at only one point. 6. The exposed die plate, on the underneath of the package, should be soldered to an equivalent area of metal on the PCB. This contact area should have multiple via connections to the back of the PCB as well as connections to intermediate PCB layers, if available, to maximize thermal dissipation away from the IC. 7. To minimize the thermal resistance of the package when soldered to a multi-layer PCB, the amount of copper track and ground plane area connected to the exposed die plate should be maximized and spread out as far as possible from the IC. The bottom and top PCB areas especially should be maximized to allow thermal dissipation to the surrounding air. 8. A signal ground plane, separate from the power ground plane and connected to the power ground pins only at the exposed die plate, should be used for ground return connections for control circuit. 9. Minimize feedback input track lengths to avoid switching noise pick-up. A demo board is available to illustrate the proper layout implementation. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 13 FN9263.1 December 14, 2007 ISL97645 Package Outline Drawing L24.4x4D 24 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 2, 10/06 4X 2.5 4.00 A 20X 0.50 B PIN 1 INDEX AREA PIN #1 CORNER (C 0 . 25) 24 19 1 4.00 18 2 . 50 0 . 15 13 0.15 (4X) 12 7 0.10 M C A B 0 . 07 24X 0 . 23 +- 0 . 05 4 24X 0 . 4 0 . 1 TOP VIEW BOTTOM VIEW SEE DETAIL "X" 0.10 C C 0 . 90 0 . 1 BASE PLANE ( 3 . 8 TYP ) SEATING PLANE 0.08 C SIDE VIEW ( 2 . 50 ) ( 20X 0 . 5 ) C 0 . 2 REF 5 ( 24X 0 . 25 ) 0 . 00 MIN. 0 . 05 MAX. ( 24X 0 . 6 ) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 14 FN9263.1 December 14, 2007