The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics
sales representative for availability and additional information.
MOS INTEGRATED CIRCUIT
µ
µµ
µ
PD434004AL
4M-BIT CMOS FAST SRAM
1M-WORD BY 4-BIT
DATA SHEET
Document No. M12225EJ7V0DS00 (7th edition)
Date Published December 2002 NS CP(K)
Printed in Japan
1996
Description
The
µ
PD434004AL is a high speed, low power, 4,194,304 bits (1,048,576 words by 4 bits) CMOS static RAM.
Operating supply voltage is 3.3 V ± 0.3 V.
The
µ
PD434004AL is packaged in a 32-pin plastic SOJ.
Features
1,048,576 words by 4 bits organization
Fast access time : 15, 17, 20 ns (MAX.)
Output Enable input for easy application
Single +3.3 V power supply
Ordering Information
Part number Package Access time Supply current mA (MAX.)
ns (MAX.) At operating At standby
µ
PD434004ALLE-A15 32-pin plastic SOJ 15 130 5
µ
PD434004ALLE-A17 (10.16 mm (400)) 17 120
µ
PD434004ALLE-A20 20 110
2
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Pin Configuration
/xxx indicates active low signal.
32-pin plastic SOJ (10.16 mm (400))
Marking Side
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A0
A1
A2
A3
A4
/CS
I/O1
V
CC
GND
I/O2
/WE
A5
A6
A7
A8
A9
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
A19
A18
A17
A16
A15
/OE
I/O4
GND
V
CC
I/O3
A14
A13
A12
A11
A10
NC
A0 to A19 : Address Inputs
I/O1 to I/O4 : Data Inputs / Outputs
/CS : Chip Select
/WE : Write Enable
/OE : Output Enable
VCC : Power supply
GND : Ground
NC : No connection
Remark Refer to Package Drawing for the 1-pin index mark.
3
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Block Diagram
A0
|
A19
Address buffer
Row decoder
Memory cell array
4,194,304 bits
GND
V
CC
/WE
/OE
/CS
Input data
controller Sense amplifier /
Switching circuit
Column decoder
Address buffer
I/O1
|
I/O4
Output data
controller
Truth Table
/CS /OE /WE Mode I/O Supply current
H×× Not selected High-Z ISB
L L H Read DOUT ICC
L×LWrite D
IN
L H H Output disable High-Z
Remark × : Don’t care
4
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Electrical Specifications
Absolute Maximum Ratings
Parameter Symbol Condition Rating Unit
Supply voltage VCC –0.5 Note to +4.6 V
Input / Output voltage VT–0.5 Note to +4.6 V
Operating ambient temperature TA0 to 70 °C
Storage temperature Tstg –55 to +125 °C
Note –2.0 V (MIN.) (pulse width : 2 ns)
Caution Exposing the device to stress above those listed in Absolute Maximum Rating could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter Symbol Condition MIN. TYP. MAX. Unit
Supply voltage VCC 3.0 3.3 3.6 V
High level input voltage VIH 2.2 VCC+0.3 V
Low level input voltage VIL –0.3 Note +0.8 V
Operating ambient temperature TA070
°C
Note –2.0 V (MIN.) (pulse width : 2 ns)
5
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
DC Characteristics (Recommended Operating Conditions Unless Otherwise Noted)
Parameter Symbol Test condition MIN. TYP. MAX. Unit
Input leakage current ILI VIN = 0 V to VCC –2 +2
µ
A
Output leakage current ILO VI/O = 0 V to VCC,–2+2
µ
A
/CS = VIH or /OE = VIH or /WE = VIL
Operating supply current ICC /CS = VIL, Cycle time : 15 ns 130 mA
II/O = 0 mA, Cycle time : 17 ns 120
Minimum cycle time Cycle time : 20 ns 110
Standby supply current ISB /CS = VIH, VIN = VIH or VIL 50 mA
ISB1 /CS VCC – 0.2 V, 5
VIN 0.2 V or VIN VCC – 0.2 V
High level output voltage VOH IOH = –4.0 mA 2.4 V
Low level output voltage VOL IOL = +8.0 mA 0.4 V
Remark VIN : Input voltage
VI/O : Input / Output voltage
Capacitance (TA = 25 °
°°
°C, f = 1 MHz)
Parameter Symbol Test condition MIN. TYP. MAX. Unit
Input capacitance CIN VIN = 0 V 6 pF
Input / Output capacitance CI/O VI/O = 0 V 10 pF
Remarks 1. VIN : Input voltage
VI/O : Input / Output voltage
2. These parameters are periodically sampled and not 100% tested.
6
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
AC Characteristics (Recommended Operating Conditions Unless Otherwise Noted)
AC Test Conditions
Input Waveform (Rise and Fall Time
3 ns)
Test Points
GND
3.0 V
1.5 V 1.5 V
Output Waveform
Test Points1.5 V 1.5 V
Output Load
AC characteristics directed with the note should be measured with the output load shown in Figure 1 or
Figure 2.
Figure 1 Figure 2
(for tAA, tACS, tOE, tOH)(for t
CLZ, tOLZ, tCHZ, tOHZ, tWHZ, tOW)
V
TT
= +1.5 V
I/O (Output)
50
Z
O
= 50
30 pF
C
L
+3.3 V
I/O (Output)
317
5 pF
C
L
351
Remark CL includes capacitances of the probe and jig, and stray capacitances.
7
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Read Cycle
Parameter Symbol -A15 -A17 -A20 Unit Notes
MIN. MAX. MIN. MAX. MIN. MAX.
Read cycle time tRC 15 17 20 ns
Address access time tAA 15 17 20 ns 1
/CS access time tACS 15 17 20 ns
/OE access time tOE 7 8 10 ns
Output hold from address change tOH 333ns
/CS to output in low impedance tCLZ 3 3 3 ns 2, 3
/OE to output in low impedance tOLZ 000ns
/CS to output in high impedance tCHZ 788ns
/OE to output hold in high impedance tOHZ 788ns
Notes 1. See the output load shown in Figure 1.
2. Transition is measured at ± 200 mV from steady-state voltage with the output load shown in Figure 2.
3. These parameters are periodically sampled and not 100% tested.
Read Cycle Timing Chart 1 (Address Access)
tOH
tRC
tAA
Address (Input)
I/O (Output) Previous data out Data out
Remarks 1. In read cycle, /WE should be fixed to high level.
2. /CS = /OE = VIL
8
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Read Cycle Timing Chart 2 (/CS Access)
Address (Input)
t
RC
t
AA
t
OLZ
/CS (Input)
I/O (Output) Data out
t
OHZ
High-Z
t
ACS
/OE (Input)
t
OE
t
CLZ
t
CHZ
High-Z
Caution Address valid prior to or coincident with /CS low level input.
Remark In read cycle, /WE should be fixed to high level.
9
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Write Cycle
Parameter Symbol -A15 -A17 -A20 Unit Notes
MIN. MAX. MIN. MAX. MIN. MAX.
Write cycle time tWC 15 17 20 ns
/CS to end of write tCW 10 11 12 ns
Address valid to end of write tAW 10 11 12 ns
Write pulse width tWP 10 11 12 ns
Data valid to end of write tDW 789ns
Data hold time tDH 000ns
Address setup time tAS 000ns
Write recovery time tWR 111ns
/WE to output in high impedance tWHZ 7 8 8 ns 1, 2
Output active from end of write tOW 333ns
Notes 1. Transition is measured at ± 200 mV from steady-state voltage with the output load shown in Figure 2.
2. These parameters are periodically sampled and not 100% tested.
Write Cycle Timing Chart 1 (/WE Controlled)
tWC
tCW
tWP
tAS tWR
Address (Input)
/CS (Input)
/WE (Input)
I/O (Input / Output)
tDHtWHZ
tAW
High-Z High-Z
tOW
Indefinite data out Data in Indefinite data out
tDW
Caution /CS or /WE should be fixed to high level during address transition.
Remarks 1. Write operation is done during the overlap time of a low level /CS and a low level /WE.
2. During tWHZ, I/O pins are in the output state, therefore the input signals must not be applied to the
output.
3. When /WE is at low level, the I/O pins are always high impedance. When /WE is at high level, read
operation is executed. Therefore /OE should be at high level to make the I/O pins high impedance.
10
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Write Cycle Timing Chart 2 (/CS Controlled)
t
WC
t
AS
t
CW
t
AW
t
WP
t
WR
t
DW
t
DH
Address (Input)
/CS (Input)
/WE (Input)
I/O (Input) High-Z Data in High-Z
Caution /CS or /WE should be fixed to high level during address transition.
Remark Write operation is done during the overlap time of a low level /CS and a low level /WE.
11
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Package Drawing
ITEM MILLIMETERS
B
C
D
E
F
G
H
I
J
K
21.26±0.2
11.18±0.2
3.5±0.2
2.545±0.2
0.8 MIN.
10.16
M
N9.4±0.20
0.12
1.27(T.P.)
2.6
0.40±0.10
P
1.005±0.1
0.74
P32LE-400A-1
U 0.20
0.1Q
T R0.85
+0.10
0.05
NOTE
Each lead centerline is located within 0.12 mm of
its true position (T.P.) at maximum material condition.
32-PIN PLASTIC SOJ (10.16mm (400))
17
16
32
1
S
N
M
Q
M
G
E
F
T
U
J
I
H
K
B
CD
P
S
12
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
Recommended Soldering Conditions
Please consult with our sales offices for soldering conditions of the
µ
PD434004AL.
Type of Surface Mount Device
µ
PD434004ALLE : 32-pin plastic SOJ (10.16 mm (400))
13
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
[ MEMO ]
14
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
[ MEMO ]
15
µ
µµ
µ
PD434004AL
Data Sheet M12225EJ7V0DS
NOTES FOR CMOS DEVICES
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
Note:
3 STATUS BEFORE INITIALIZATION OF MOS DEVICES
HANDLING OF THE APPLIED WAVEFORM OF INPUT PINS AND THE UNUSED INPUT PINS
FOR CMOS
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
Input levels of CMOS devices must be fixed. CMOS devices behave differently than Bipolar or
NMOS devices. If the input of a CMOS device stays in an area that is between V
IL
(MAX.) and
V
IH
(MIN.) due to the effects of noise or some other irregularity, malfunction may result.
Therefore, not only the input waveform is fixed, but also the waveform changes, it is important
to use the CMOS device under AC test conditions. For unused input pins in particular, CMOS
devices should not be operated in a state where nothing is connected, so input levels of CMOS
devices must be fixed to high or low by using pull-up or pull-down circuitry. Each unused pin
should be connected to V
DD
or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device
and related specifications governing the devices.
µ
µµ
µ
PD434004AL
The information in this document is current as of December, 2002. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-
designated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1