SMD LED Product Data Sheet LTST-G683RGBW Spec No.: DS22-2011-0302 Effective Date: 10/14/2016 Revision: B LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto SMD LED LTST-G683RGBW 1. Description SMD LEDs from Lite-On are available in miniature sizes and special configurations for automated PC board assembly and space-sensitive applications. These SMD LEDs are suitable for use in a wide variety of electronic equipment, including cordless and cellular phones, notebook computers, network systems, home appliances, and indoor signboard applications. 1.1 Features 1.2 Applications Meet ROHS Package in 8mm tape on 7" diameter reels EIA STD package I.C. compatible Compatible with automatic placement equipment Compatible with infrared reflow solder process Preconditioning: accelerate to JEDEC level 3 Telecommunication, Office automation, home appliances, industrial equipment Status indicator Signal and Symbol Luminary Front panel backlighting 2. Package Dimensions Part No. LTST-G683RGBW Lens Color White Diffused Source Color Pin Assignment InGaN Blue 1, 6 InGaN Green 2, 5 AlInGaP Red 3, 4 Notes: 1. 2. All dimensions are in millimeters. Tolerance is 0.2 mm (.008") unless otherwise noted. 1/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 3. Rating and Characteristics 3.1 Absolute Maximum Ratings at Ta=25C LTST-G683RGBW Parameter Power Dissipation Unit Red Green Blue 72 80 80 mW 80 100 100 mA 30 20 20 mA Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Operating Temperature Range -40C to + 85C Storage Temperature Range -40C to + 100C 3.2 Suggest IR Reflow Condition for Pb Free Process: IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B) 2/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 3.3 Electrical / Optical Characteristics at Ta=25C LTST-G683RGBW Parameter Luminous Intensity Symbol IV Viewing Angle 21/2 Dominant Wavelength d Red Green Blue Min. 90 355 180 Typ. - - - Max. 224 710 355 Typ. Min. 120 624 520 Unit. Test Condition mcd IF = 20mA Note 1 deg Note 2 (Fig.5) nm IF = 20mA Note 3 465 Max. 636 530 475 Peak Emission Wavelength P Typ. 639 518 465 nm Measurement @Peak (Fig.1) Spectral Line Half-Width Typ. 20 35 25 nm - Min. 1.8 2.8 2.8 Forward Voltage VF V IF = 20mA Note 4 Max. Reverse Current IR 2.4 Max. 3.8 10 3.8 A VR = 5V Note 5 Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, d is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device 4. Forward Voltage Tolerance is +/- 0.1 volt. 5. Reverse voltage (VR) condition is applied to IR test only. The device is not designed for reverse operation. 3/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 4. Bin Code List Luminous Intensity Luminous Intensity Unit : mcd @20mA Red Green Blue Bin Code Min Max Min Max Min Max 140 180 180 224 A3 224 280 A4 280 355 A5 140 180 180 224 A7 224 280 A8 280 355 A9 140 180 180 224 A11 224 280 A12 280 355 B1 140 180 180 224 B3 224 280 B4 280 355 B5 140 180 180 224 B7 224 280 B8 280 355 B9 140 180 180 224 B11 224 280 B12 280 355 A1 A2 355 450 A6 90 112 450 560 A10 560 710 B2 355 450 B6 112 140 450 560 B10 560 710 Tolerance on each Intensity bin is +/-11% 4/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW Luminous Intensity Luminous Intensity Unit : mcd @20mA Red Green Blue Bin Code Min Max Min Max Min Max 140 180 180 224 C3 224 280 C4 280 355 C5 140 180 180 224 C7 224 280 C8 280 355 C9 140 180 180 224 C11 224 280 C12 280 355 D1 140 180 180 224 D3 224 280 D4 280 355 D5 140 180 180 224 D7 224 280 D8 280 355 D9 140 180 180 224 D11 224 280 D12 280 355 C1 C2 355 450 C6 140 180 450 560 C10 560 710 D2 355 450 D6 180 224 450 560 D10 560 710 Tolerance on each Intensity bin is +/-11% 5/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW Dominant Wavelength Dominant Wavelength Red Unit : nm @20mA Green Blue Bin Code Min Max Min Max 520 525 E1 E2 624 Max 465 470 470 475 465 470 470 475 636 E3 525 E4 Min 530 Tolerance for each Dominate Wavelength Bin is +/- 1nm 6/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 5. Typical Electrical / Optical Characteristics Curves. (25C Ambient Temperature Unless Otherwise Noted) 7/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 6. User Guide 6.1 Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less one minute. 6.2 Recommend Printed Circuit Board Attachment Pad 6.3 Package Dimensions of Tape And Reel Note: 1. All dimensions are in millimeters (inches). 8/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 6.4 Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel 2000 pieces per reel. 3. Minimum packing quantity is 500 pieces for remainders. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with EIA-481-1-B specifications. 9/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 7. Cautions 7.1 Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon's Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 7.2 Storage The package is sealed: The LEDs should be stored at 30C or less and 70%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The storage ambient for the LEDs should not exceed 30C temperature and 60% relative humidity. It is recommended that LEDs out of their original packaging are IR-reflowed within 168hrs. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. LEDs stored out of their original packaging for more than 168hrs should be baked at about 60 C for at least 48 hours before solder assembly. 7.3 Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 7.4 Soldering Recommended soldering conditions: Reflow soldering Pre-heat Pre-heat time Peak temperature Soldering time 150~200C 120 sec. Max. 260C Max. 10 sec. Max.(Max. two times) Soldering iron Temperature Soldering time 300C Max. 3 sec. Max. (one time only) Notes: Because different board designs use different number and types of devices, solder pastes, reflow ovens, and circuit boards, no single temperature profile works for all possible combinations. However, you can successfully mount your packages to the PCB by following the proper guidelines and PCB-specific characterization. LITE-ON Runs both component-level verification using in-house KYRAMX98 reflow chambers and board-level assembly. The results of this testing are verified through post-reflow reliability testing.Profiles used at LITE-ON are based on JEDEC standards to ensure that all packages can be successfully and reliably surface mounted. Figure on page3 shows a sample temperature profile compliant to JEDEC standards. You can use this example as a generic target to set up your reflow process. You should adhere to the JEDEC profile limits as well as specifications and recommendations from the solder paste manufacturer to avoid damaging the device and create a reliable solder joint. 10/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 7.5 Drive Method A LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 7.6 ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED's plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or " no lightup " at low currents. To verify for ESD damage, check for " lightup " and Vf of the suspect LEDs at low currents. The Vf of " good " LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. 11/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 8. Reliability Test No. Test item 1 Resistance to soldering heat 2 Solderability Test condition Reference standard Tsld = 260C, 10sec. 3 times JEITA ED-4701 300 301 Tsld=245 5C (Lead Free Solder, Coverage 95% of the JEITA ED-4701 300 303 dipped surface) 3 Thermal Shock 85 5C ~ -30C 5C 30min 30min 100cycles JEITA ED-4701 300 307 4 Temperature Cycle -55C ~ 25C ~ 100C ~ 25C 30min 5min 30min 5min 100cycles JEITA ED-4701 100 105 5 High Temperature Storage 100C 1000hrs JEITA ED-4701 200 201 6 Low Temperature Storage -55C 1000hrs JEITA ED-4701 200 202 7 Temperature Humidity Storage 60C/90%RH 300hrs 8 Room temp life test 25C, IF: Max current , 1000hrs JEITA ED-4701 100 103 -- 9. Others The appearance and specifications of the product may be modified for improvement without prior notice. 12/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4 SMD LED LTST-G683RGBW 10. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wears wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for InGaN LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycles? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? 13/13 Part No. : LTST-G683RGBW BNS-OD-FC002/A4