INCH-POUND MIL-DTL-83723/71C 18 August 2009 SUPERSEDING MIL-C-83723/71B 30 June 1992 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (FLANGE MOUNT, BAYONET COUPLING, CRIMP SOCKET CONTACT), SERIES III, CLASSES A, G, M, R, T, W AND Z This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Receptacle, dimensions and configurations. AMSC N/A FSC 5935 MIL-DTL-83723/71C Inches .015 .035 .051 .054 .076 mm 0.38 0.89 1.30 1.37 1.93 Inches .092 .096 .114 .118 .125 mm Inches 2.34 2.44 2.90 3.00 3.18 .146 .150 .155 .169 .206 mm 3.71 3.81 3.94 4.29 5.23 Inches .210 .250 mm 5.33 6.35 FIGURE 1. Receptacle, dimensions and configurations - Continued. 2 MIL-DTL-83723/71C Shell size A C D F J K L 8 .120 (3.05) .312 (7.92) .594 (15.09) .812 (20.62) .120 (3.05) .696 (17.68) .719 (18.26) .937 (23.80) .636 (16.15) 12 .120 (3.05) .875 (22.23) .812 (20.62) 1.031 (26.19) .806 (20.47) 14 .120 (3.05) .935 (23.75) .906 (23.01) 1.125 (28.58) .875 (22.23) 16 .120 (3.05) 1.062 (26.97) .969 (24.61) 1.250 (31.75) 1.002 (25.45) 18 .120 (3.05) 1.187 (30.15) 1.062 (26.97) 1.343 (34.11) 1.108 (28.14) 20 .120 (3.05) 1.312 (33.32) 1.156 (29.36) 1.437 (36.50) 1.233 (31.32) 22 .120 (3.05) 1.437 (36.50) 1.250 (31.75) 1.562 (39.67) 1.358 (34.49) 24 .149 (3.78) .536 (13.61) .531 (13.49) .659 (16.74) .654 (16.61) .829 (21.06) .824 (20.93) .898 (22.81) .893 (22.68) 1.025 (26.04) 1.020 (25.91) 1.131 (28.73) 1.126 (28.60) 1.256 (31.90) 1.251 (31.78) 1.381 (35.08) 1.376 (34.95) 1.506 (38.25) 1.501 (38.13) .561 (14.25) 10 .428 (10.87) .433 (11.00) .530 (13.46) .535 (13.59) .700 (17.78) .705 (17.91) .769 (19.53) .774 (19.66) .869 (22.07) .901 (22.89) 1.002 (25.45) 1.007 (25.58) 1.127 (28.63) 1.132 (28.75) 1.252 (31.80) 1.257 (31.93) 1.377 (34.98) 1.382 (35.10) S + .005 (0.13) - .000 .508 (12.90) 1.562 (39.67) 1.375 (34.93) 1.703 (43.26) 1.483 (37.67) .388 (9.86) .558 (14.17) .627 (15.93) .772 (19.61) .860 (21.84) .985 (25.02) 1.110 (28.19) 1.235 (31.37) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. Metric equivalents are in parentheses. 3. Unless otherwise specified, tolerances shall be .005 (0.13) for three place decimal places, .01 (0.25) for two place decimal places and 1 for all angles. 4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723 and SAE-AS85049. 5. The centerline of indicated projection shall be located on the vertical centerline within 2. FIGURE 1. Receptacle, dimensions and configurations - Continued. 3 MIL-DTL-83723/71C REQUIREMENTS: Dimensions and configurations: See figure 1. For insert arrangement, see MIL-STD-1554. For connector accessories, see SAE-AS85049. This connector mates with MIL-DTL-83723/76 and MIL-DTL-83723/78. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for lead-in chamfers on contact cavities. Shell size 8 10 Insert arrangements 03 06 Contact cavities 1, 2, and 3 1, 2, 3, 4, 5, 6 Marking: Part or Identifying Number (PIN): M83723/71 - X (where "X" represents the dash number from figure 1), shell size, and the applicable code for finish. PIN example: M83723/ Military designator Specification sheet number Class Shell size Insert arrangement Polarizing position 4 71 W 10 55 N MIL-DTL-83723/71C Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/76 MIL-DTL-83723/78 MIL-STD-1554 SAE-AS85049 CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5935-2008-125) Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 5