ah = CLONU TS79L00 Series Pd) RoHS 3-Terminal 100mA Negative Voltage Regulator 2 COMPLIANCE TO-92 SOT-89 Pin Definition: SOP-8 Pin Definition: S| . 1. Ground General Description 1. Output 8. N/C 4.N/C 5. Ground 7 ui 2. Input 2. Input 7. Input 3. Output : 3. Input 6. Input The TS79L00 Series of negative voltage regulators are inexpensive, easy-to-use devices suitable for a multitude of applications that require a regulated supply of up to 100mA. Like their higher power TS7900 and TS79MOO Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the TS79L00 devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode-resistor combination, as output impedance and quiescent current are substantially reduced. Features Output Voltage Range -5 to -24V Output current up to 100mA No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance Ordering Information Part No. Package Packing TS79LxxCT BO TO-92 1Kpcs / Bulk TS79LxxCT A3 TO-92 2Kpcs / Ammo TS79LxxCY RM SOT-89 1Kpcs / 7 Reel TS79LxxCS RL SOP-8 2.5Kpcs / 13 Reel Note: Where xx denote voltage option Standard Application Circuit Input Output oO IN OUT oO TS79L00 we + C1 C2 =~ 0.33uF GND > (O.1uF Tant. Tant. A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Absolute Maximum Rating (Ta = 25C unless otherwise noted) Parameter Symbol Limit Unit Input Voltage Vin* -35 V Input Voltage Vin* -40 Power Dissipation Pp Internal Limited WwW Operating Temperature range Topr 0~+125 C Junction Temperature Ty +150 C Storage Temperature Range Tste -65~+150 C Note: * TS79L05 to TS79L18 TS79L24 1/9 Version: B07ma COMPLIANCE TS79L05 Electrical Characteristics S ae TS79L00 Series 5) RoHS 3-Terminal 100mA Negative Voltage Regulator (Vin=-10V, lout=40mA, 0C<Tj<125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C -4.80 -5 -5.20 Output voltage Vout -7.5V<Vins-20V, Vv 5mAslouts100mA 4.75 9.28 Line Regulation REGline Tj=25C_ | -7.5VsVins-20V -- 50 150 mV Aslouts1 A -- 2 Load Regulation REGload | Ti<25C -2MAslouts 100m o 60 5mAslout<40mA -- 10 30 Quiescent Current Iq lout=0, Tj=25C -- 3 6 -7.5VsVins--25V -- -- 1. mA Quiescent Current Change Alq oVsVins~25 2 5mAslouts=40mA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 40 -- wv Ripple Rejection Ratio RR f=120Hz, -8VsVins-18V 41 49 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - V Peak Output Current lo peak Tj=25C -- 0.15 -- A T t fficient of emperature Coefficient of 1 Aout; AT] | lout=5mA, OC<Tj<125C _- -0.65 - | mvec Output Voltage TS79L06 Electrical Characteristics (Vin=-11V, lout=40mA, 0C<Tjs125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 5.76 6 6.24 Output voltage Vout -8.5VsVins-21V, V 5mAslouts100MA 9-70 6 6.30 Line Regulation REGline Tj=25C_ | -8.5VsVins-21V - 50 150 mV Aslouts1 A -- 2 Load Regulation REGload | Ti<25C -2MAsloutst00m 0 60 5mAslout<40mA -- 10 30 Quiescent Current Iq lout=0, Tj=25C -- 3 6 -10.5VsVins-21V -- -- 1. A Quiescent Current Change Alq 0.0VsVins 2 m 5mAslouts=40mA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 40 -- wv Ripple Rejection Ratio RR f=120Hz, -10.5V<Vins-21V 44 49 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - V Peak Output Current lo peak Tj=25C -- 0.15 -- A T t fficient of emperature Coefficient of) AVouy at) | lout=5mA, 0C<Tj<125C - -0.75 - | mvfc Output Voltage @ Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. @ This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/9 Version: B07> E oe TS79L00 Series 5) RoHS 3-Terminal 100mA Negative Voltage Regulator = COMPLIANCE TS79L08 Electrical Characteristics Vin=-14V, lout=40mA, 0CsTjs125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 7.69 8 8.32 Output voltage Vout -10.5V<sVins-23V, V 5mAslout<100mA 761 8 8.40 Line Regulation REGline Tj=25C_ | -10.5VsVins-25V - 80 160 mV Aslouts1 A -- 2 Load Regulation REGload | Ti<25C -2MAsloutst00m a 80 5mAslouts40mMA - 10 40 Quiescent Current Iq lout=0, Tj=25C -- 3 6 -10.5VsVins-23V -- -- 1. mA Quiescent Current Change Alq 0.9VsVins-23 5mAslouts40mMA - - 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 60 -- wv Ripple Rejection Ratio RR f=120Hz, -11VsVins-23V 37 57 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - Vv Peak Output Current lo peak | Tj=25C - 0.15 - A T t fficient of emperature Coefficient of | AVouy atj | lout=5mA, 0C<Tj<125C - 0.8 - mVPC Output Voltage TS79L09 Electrical Characteristics Vin=-15V, lout=40mA, 0CsTjs125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 8.65 9 9.36 Output voltage Vout -11.5VsVins-24V, Vv 57 4 5mAslouts100MA 8.0 9 9.48 Line Regulation REGline Tj=25C_ | -11.5VsVins-24V -- 90 180 mV Aslouts1 A -- Load Regulation REGload | Ti=25C -2MAslouts 100m 30 20 5mAslouts40mMA - 15 45 Quiescent Current Iq lout=0, Tj=25C -- 3 6 =11V<Vins=23V - - 1. A Quiescent Current Change Alq sVins=23 a m 5mAslouts40mMA - - 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 60 -- Vv Ripple Rejection Ratio RR f=120Hz, =13VsVins=24V 37 57 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - Vv Peak Output Current lo peak Tj=25C -- 0.15 -- A T t fficient of emperature Coefficient of | AVouy vty | lout=5mA, 0C<Tj<125C -- 0.9 - mVPC Output Voltage @ Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. @ This specification applies only for DC power dissipation permitted by absolute maximum ratings. 3/9 Version: BO7E i Pp) ROHS ma ~=9 COMPLIANCE TS79L12 Electrical Characteristics TS79L00 Series Vin=-19V, lout=40mA, 0CsTj<125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) 3-Terminal 100mA Negative Voltage Regulator Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 11.53 12 12.48 Output voltage Vout -14. ins- V utput voltag u 14.5V<Vins-27V, 41.42 42 12.60 5mAslout<100MA Line Regulation REGline Tj=25C_ | -14.5VsVins-27V -- 120 240 mV Aslouts1 A - 4 12 Load Regulation REGload | Ti<25C -2MAsloutst00m 0 0 5mAslouts40mA -- 20 60 Quiescent Current Iq lout=0, Tj=25C -- 3 6.5 -16VsVins-27V - - 1. A Quiescent Current Change Alq 6VsVins m 5mAslouts40mA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 80 -- wv Ripple Rejection Ratio RR f=120Hz, -11VsVins-23V 37 42 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - Vv Peak Output Current lo peak Tj=25C -- 0.15 -- A T t fficient of emperature Coefficient of | AVouy atj | lout=5mA, 0C<Tj<125C - -1.0 - mvV/ C Output Voltage TS79L15 Electrical Characteristics Vin=-23V, lout=40mA, 0C<Tj<125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 14.42 15 15.60 Output voltage Vout -17.5VsVins-30V, Vv 5mAslouts100MA 14.28 1S 15.75 Line Regulation REGline Tj=25C_ | -17.5VsVins-24V -- 150 30 mV Aslouts1 A -- 1 Load Regulation REGload | Ti<25C -2MAstouts 100m 50 30 5mAslouts40mA -- 25 75 Quiescent Current Iq lout=0, Tj=25C -- 3 6.6 -20VsVins-30V -- -- 1. mA Quiescent Current Change Alq OVsVins 30 5mAslouts40mA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 90 -- wv Ripple Rejection Ratio RR f=120Hz, -18V<Vins-28V 34 39 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - V Peak Output Current lo peak =| Tj=25C - 0.15 - A T t fficient of emperature Coefficient of | Aout at] | lout=5mA, OC<Tj<125C _- 13 _- mVPC Output Voltage @ Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. @ This specification applies only for DC power dissipation permitted by absolute maximum ratings. 4/9 Version: B07SST E Nl Pb) ROHS Yea COMPLIANCE TS79L18 Electrical Characteristics TS79L00 Series Vin=-27V, lout=40mA, 0CsTjs125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) 3-Terminal 100mA Negative Voltage Regulator Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 17.30 18 18.72 Output voltage Vout -21VsVins-33V, V 5mAslouts100MA 17.14 18 18.90 Line Regulation REGline Tj=25C_ | -21<Vins-33V - 180 360 mV Aslouts1 A - 1 Load Regulation REGload | Tiz25C -2MAslouts 100m 60 80 5mAslouts40mA -- 30 90 Quiescent Current Iq lout=0, Tj=25C -- 3 6.5 -21VsVins-33V -- -- 1. mA Quiescent Current Change Alq sVins 33 2 5mAslouts40mMA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 150 -- wv Ripple Rejection Ratio RR f=120HZ, -23V<Vins-33V 33 48 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - Vv Peak Output Current lo peak =| Tj=25C - 0.15 - A T t fficient of emperature Coefficient of | AVouy vty | lout=5mA, 0C<Tj<125C - 415 - mVPC Output Voltage TS79L24 Electrical Characteristics Vin=-33V, lout=40mA, 0C<Tjs125C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Unit Tj=25C 23.07 24 24.96 Output voltage Vout -27V<Vins-38V, Vv 5mAslouts100mMA 22.85 24 29.20 Line Regulation REGline Tj=25C_ | -27<Vins-38V -- 200 400 mV Aslouts1 A -- 24 Load Regulation REGload | Ti<25C }2MAsloutst00m 80 0 5mAslouts40mA -- 40 120 Quiescent Current Iq lout=0, Tj=25C -- 4 7 -27VsVins-38V -- - 1. A Quiescent Current Change Alq sVins 38 m 5mAslouts40mMA -- -- 0.1 Output Noise Voltage Vn 10Hz<f<100KHz, Tj=25C -- 200 -- wv Ripple Rejection Ratio RR f=120Hz, -29V<Vins-35V 31 45 -- dB Voltage Drop Vdrop lout=100mA, Tj=25C - 1.7 - Vv Peak Output Current lo peak Tj=25C -- 0.15 -- A T t fficient of emperature Coefficient of | AVouy atj | lout=5mA, 0C<Tj<125C -- -2.0 - mVPC Output Voltage @ Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. @ This specification applies only for DC power dissipation permitted by absolute maximum ratings. 5/9 Version: B07o) ROHS COMPLIANCE 7 TEA DUSEOA TS79L00 Series Marking Diagram TSC 79Lxx YML i 2a 3-Terminal 100mA Negative Voltage Regulator TO-92 Mechanical Drawing TO-92 DIMENSION pig L_MILLIMETERS INCHES MIN MAX MIN MAX A | 4.30 470 | 0.169 | 0.185 B | 4.30 470 | 0.169 | 0.185 C 14.30(typ) 0.563(typ) D 0.43 049 | 0.017 | 0.019 E 2.19 2.81 0.086 | 0.111 F 3.30 3.70 | 0.130 | 0.146 G | 242 2.66 | 0.095 | 0.105 H 0.37 0.43 | 0.015 | 0.017 Oo 0 al G XX = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) Y =Year Code M =Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=-Sep, J=Oct, K=Nov, L=Dec) L = Lot Code 6/9 Version: BO7SB | TS79L00 Series (0) RoHS 3-Terminal 100mA Negative Voltage Regulator COMPLIANCE SOT-89 Mechanical Drawing J__* SOT-89 DIMENSION | | pim |_MILLIMETERS INCHES 8 MIN MAX | MIN MAX r | A 4.40 4.60 0.173 | 0.181 7 | B 1.50 1.7 0.059 | 0.070 | C 2.30 2.60 0.090 | 0.102 | D 0.40 0.52 | 0.016 | 0.020 E 1.50 1.50 0.059 | 0.059 H C F | 3.00 3.00 | 0.118 | 0.118 G 0.89 1.20 0.035 | 0.047 G | Le H 4.05 4.25 0.159 | 0.167 j 1.4 1.6 0.055 | 0.068 1 | J 0.35 0.44 0.014 | 0.017 Marking Diagram C........) XX = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) OLxx Y = Year Code YML. M =Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=-Sep, J=Oct, K=Nov, L=Dec) |_| | |_| L = Lot Code 1 2 3 7/9 Version: BO7i SB |. TS79L00 Series con 3-Terminal 100mA Negative Voltage Regulator (Pb) RoHS g g g Nea COMPLIANCE SOP-8 Mechanical Drawing A SOP-8 DIMENSION H H H DIM MILLIMETERS INCHES MIN MAX MIN MAX. A 4.80 5.00 0.189 0.196 B 3.80 4.00 0.150 0.157 BP C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 O F 0.40 1.25 0.016 0.049 G 1.27BSC 0.05BSC H H H a K 0.10 0.25 0.004 0.009 M 0 7 0 7 GJ P 5.80 6.20 0.229 0.244 R R 0.25 0.50 0.010 0.019 [ aca TAA AV SSSR D 7 LEI Marking Diagram A Cl C4 7 XX = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) TS79Lxx Y = Year Code M =Month Code YML Sb (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, oO J=Oct, K=Nov, L=Dec) Ly | |_| J L =Lot Code 8/9 Version: BO7Sb Baer TS79L00 Series (o) RoHS 3-Terminal 100mA Negative Voltage Regulator @& COMPLIANCE Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSCs terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 9/9 Version: BO7