SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 D Controlled Baseline D D D D D D D D D D D D - One Assembly/Test Site, One Fabrication Site Extended Temperature Performance of -55C to 125C Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product Change Notification Qualification Pedigree Rail-to-Rail Output Swing Gain Bandwidth Product . . . 6.4 MHz 80 mA Output Drive Capability D Supply Current . . . 500 A/channel Input Offset Voltage . . . 100 V Input Noise Voltage . . . 11 nV/Hz Slew Rate . . . 1.6 V/s Micropower Shutdown Mode (TLV2460/3) . . . 0.3 A/Channel Universal Operational Amplifier EVM TLV2460 D PACKAGE (TOP VIEW) NC IN - IN + GND Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. 1 8 2 7 3 6 4 5 SHDN VDD+ OUT NC description The TLV246x is a family of low-power rail-to-rail input/output operational amplifiers specifically designed for portable applications. The input common-mode voltage range extends beyond the supply rails for maximum dynamic range in low-voltage systems. The amplifier output has rail-to-rail performance with high-output-drive capability, solving one of the limitations of older rail-to-rail input/output operational amplifiers. This rail-to-rail dynamic range and high output drive make the TLV246x ideal for buffering analog-to-digital converters. The operational amplifier has 6.4 MHz of bandwidth and 1.6 V/s of slew rate with only 500 A of supply current, providing good ac performance with low power consumption. Devices are available with an optional shutdown terminal, which places the amplifier in an ultralow supply current mode (IDD = 0.3 A/ch). While in shutdown, the operational-amplifier output is placed in a high-impedance state. DC applications are also well served with an input noise voltage of 11 nV/Hz and input offset voltage of 100 V. ORDERING INFORMATION -40C to 125C -55C -55 C to 125 125C C ORDERABLE PART NUMBER PACKAGE TA TOP-SIDE MARKING D Tape and reel TLV2462AQDREP 2462AE D Tape and reel TLV2463AQDREP V2463AQE D Tape and reel TLV2462AMDREP 2462AM D Tape and reel TLV2464AMDREP V2464AME PW Tape and reel TLV2464AMPWREP 2464AME Some of the TLV246x family, along with packaging options, are in the Product Preview stage of development. Contact the local Texas Instruments sales office for availability. Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2005, Texas Instruments Incorporated !"#$%! & '("")% $& ! *(+,'$%! -$%). "!-('%& '!!"# %! &*)''$%!& *)" %/) %)"#& ! )0$& &%"(#)%& &%$-$"- 1$""$%2. "!-('%! *"!')&&3 -!)& !% )')&&$",2 ',(-) %)&%3 ! $,, *$"$#)%)"&. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TLV246x PACKAGE PINOUTS TLV2461 D or PW PACKAGE (TOP VIEW) NC IN - IN + GND 1OUT 1IN - 1IN+ GND NC 1SHDN NC 1 8 2 7 3 6 4 5 TLV2462 D or PW PACKAGE (TOP VIEW) NC VDD+ OUT NC 1OUT 1IN - 1IN + GND 1 8 2 7 3 6 4 5 TLV2463 D or PW PACKAGE TLV2464 D or PW PACKAGE (TOP VIEW) (TOP VIEW) 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VDD+ 2OUT 2IN - 2IN+ NC 2SHDN NC 1OUT 1IN - 1IN+ VDD+ 2IN+ 2IN - 2OUT 1 14 2 13 3 12 4 11 5 10 6 9 7 8 NC - No internal connection 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VDD+ 2OUT 2IN - 2IN+ 4OUT 4IN - 4IN+ GND 3IN+ 3IN - 3OUT SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Differential input voltage, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.2 V to VDD + 0.2 V Input current, II (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 mA Total input current, II (into VDD +) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 mA Total output current, IO (out of GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 125C Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values, except differential voltages, are with respect to GND. THERMAL RESISTANCE TABLE JC (C/W) PACKAGE JA (C/W, 0 Air Flow) High K Low K D (8) 39.4 42.4 97.1 High K 165.5 Low K D (14) 51.5 53.7 86.2 133.5 PW (8) 65.1 69.4 149.4 230.5 PW (14) 45.8 46.6 111.7 131.4 NOTE: Thermal resistances are not production tested and are for informational purposes only. 1e+08 805C 1.7e+07 Hrs (1.9e+03 years) 1e+07 Time-to-Fail - Hr 905C 5.2e+06 Hrs (5.9e+02 years) 1005C 1.7e+06 Hrs (1.9e+02 years) 1e+06 1105C 5.8e+05 Hrs (66 years) 1205C 2.1e+05 Hrs (24 years) 100000 1305C 8.2e+04 Hrs (9.3 years) 1405C 3.3e+04 Hrs (3.7 years) 10000 1000 80 90 100 110 120 130 140 150 Degrees C Continous - TJ Figure 1. Wirebond Life Estimation Plot POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 recommended operating conditions MIN Single supply Supply voltage, VDD Split supply Common-mode input voltage range, VICR VIH VIL Shutdown on/off voltage level Operating free-air temperature, TA Relative to voltage on the GND terminal of the device. 4 POST OFFICE BOX 655303 2.7 6 1.35 3 -0.2 VDD+0.2 2 0.7 -40 * DALLAS, TEXAS 75265 MAX 125 UNIT V V V C SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage IIO Input offset current IIB Input bias current TEST CONDITIONS TA 25C VDD = 3 V, VO = 1.5 V, VIC = 1.5 V, RS = 50 Full range VDD = 3 V, VO = 1.5 V, VIC = 1.5 V, RS = 50 Full range MIN 2.8 4.4 High-level output voltage IOL = 2.5 mA Low-level output voltage IOL = 10 mA Sourcing 2.5 0.1 Full range 0.2 0.5 Full range IO Output current Measured 1 V from rail AVD Large-signal differential voltage amplification RL = 10 k ri(d) Differential input resistance ci(c) Common-mode input capacitance f = 10 kHz zo Closed-loop output impedance f = 100 kHz, kSVR Common-mode rejection ratio Supply voltage rejection ratio ((V VDD //V VIO) 50 20 25C Sinking AV = 10 VICR = 0 V to 3 V, RS = 50 VDD = 2.7 V to 6 V, No load VIC = VDD /2, VDD = 3 V to 5 V, No load VIC = VDD /2, Supply current (per channels) VO = 1.5 V, No load IDD(SHDN) Supply current in shutdown (TLV2460, TLV2463) SHDN < 0.7 V, Per channel in shutdown mA 40 20 40 25C 25C 90 Full range 89 mA 105 dB 25C 109 25C 7 pF 33 25C 25C 66 Full range 60 25C 80 Full range 75 25C 85 Full range 80 25C IDD V 0.3 Full range Full range nA V 2.7 25C Short-circuit output current 14 2.9 25C VIC = 1.5 V, nA 2.8 25C VIC = 1.5 V, V V 7 75 25C Full range UNIT V/C 75 25C Full range IOH = - 10 mA CMRR 1500 2 25C IOS 150 Full range IOH = - 2.5 mA VOL MAX 1700 25C VOH TYP 80 dB 85 0.5 Full range 25C Full range dB 95 0.575 0.9 0.3 2.5 mA A A Full range is -40C to 125C for the Q suffix and -55C to 125C for the M suffix. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 operating characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER SR Slew rate at unity gain Vn Equivalent input noise voltage In THD + N t(on) TEST CONDITIONS VO(PP) = 2 V, RL = 10 k CL = 160 pF, TA 25C Full range 25C 11 Equivalent input noise current f = 1 kHz 25C 0.13 Total harmonic distortion plus noise VO(PP) = 2 V, RL = 10 k, f = 1 kHz Amplifier turnon time AV = 1 AV = 10 Channel 1 only, Channel 2 on Amplifier turnoff time Channel 1 only, Channel 2 on AV = 1, RL = 10 k Settling time f = 10 kHz, CL = 160 pF RL = 10 k, 7.6 25C 7.65 25C 25 C 328 ns 329 25C 5.2 0.1% 1.77 0.01% 1.98 RL = 10 k, CL = 160 pF MHz 1.47 0.01% 1.78 25C * DALLAS, TEXAS 75265 s 333 V(STEP)PP = 2 V, AV = -1, CL = 56 pF, RL = 10 k POST OFFICE BOX 655303 pA /Hz 0.08% 0.1% Full range is -40C to 125C for the Q suffix and -55C to 125C for the M suffix. nV/Hz 0.02% V(STEP)PP = 2 V, AV = -1, CL = 10 pF, RL = 10 k Phase margin at unity gain UNIT 0.006% 25C 25 C AV = 100 Both channels AV = 1, RL = 10 k MAX V/s 0.8 f = 1 kHz Gain margin 6 1.6 16 Gain-bandwidth product m 1 25C Channel 2 only, Channel 1 on ts TYP f = 100 Hz Both channels t(off) MIN 25C 44 25C 7 ss dB SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS VIO Input offset voltage VIO Temperature coefficient of input offset voltage IIO Input offset current IIB Input bias current VDD = 5 V, VO = 2.5 V, VDD = 5 V, VO = 2.5 V, TA 25C VIC = 2.5, RS = 50 Full range VIC = 2.5 V, RS = 50 Full range MIN 1500 25C 2 25C 0.3 1.3 IOL = 2.5 mA Low-level output voltage IOL = 10 mA Sourcing 4.7 0.1 Full range 0.2 0.3 145 60 25C Sinking Full range 60 80 Output current Measured at 1 V from rail 25C VIC = 2.5 V, VO = 1 V to 4 V 25C 92 AVD Large-signal differential voltage amplification Full range 90 ri(d) Differential input resistance ci(c) Common-mode input capacitance f = 10 kHz zo Closed-loop output impedance f = 100 kHz, CMRR Common-mode rejection ratio VICR = 0 V to 5 V, RS = 50 kSVR Supply voltage rejection ratio ((V VDD //V VIO) AV = 10 VDD = 2.7 V to 6 V, No load VIC = VDD /2, VDD = 3 V to 5 V, No load VIC = VDD /2, No load, Supply current (per channel) VO = 2.5 V, IDD(SHDN) Supply current in shutdown (TLV2460, TLV2463) SHDN < 0.7 V, Per channels in shutdown mA 109 dB 25C 109 25C 7 pF 25C 29 25C 71 Full range 60 25C 80 Full range 75 25C 85 Full range 80 25C IDD mA 100 IO RL = 10 k, V 0.2 Full range Full range nA V 4.8 25C Short-circuit output current 14 4.8 25C VIC = 2.5 V, nA 4.9 25C VIC = 2.5 V, V V 7 60 25C Full range UNIT V/C V/C 60 25C Full range High-level output voltage IOH = - 10 mA IOS 150 1700 25C VOL MAX Full range IOH = - 2.5 mA VOH TYP 85 dB 85 dB 95 dB 0.55 Full range 25C Full range 0.65 1 1 3 mA A A Full range is -40C to 125C for the Q suffix and -55C to 125C for the M suffix. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER SR Slew rate at unity gain Vn Equivalent input noise voltage In THD + N t(on) t(off) TEST CONDITIONS VO(PP) = 2 V, RL = 10 k CL = 160 pF, TA 25C Full range 1.6 f = 1 kHz 25C 11 Equivalent input noise current f = 100 Hz 25C 0.13 Total harmonic distortion plus noise VO(PP) = 4 V, RL = 10 k, f = 10 kHz Amplifier turnon time Amplifier turnoff time AV = 1 AV = 10 AV = 1, RL = 10 k AV = 1, RL = 10 k Settling time 7.6 25C 25 C 7.65 Both channels 333 25 C 25C 328 RL = 10 k, V(STEP)PP = 2 V, AV = -1, CL = 10 pF, RL = 10 k 0.1% V(STEP)PP = 2 V, AV = -1, CL = 56 pF, RL = 10 k 0.1% 3.13 0.01% 3.33 RL = 10 k, CL = 160 pF POST OFFICE BOX 655303 25C ns 6.4 MHz 1.53 0.01% 1.83 ss 25C * DALLAS, TEXAS 75265 s 329 f = 10 kHz, CL = 160 pF Full range is -40C to 125C for the Q suffix and -55C to 125C for the M suffix. pA /Hz 0.04% 7.25 Phase margin at unity gain nV/Hz 0.01% Channel 2 only, Channel 1 on Channel 1 only, Channel 2 on UNIT 0.004% 25C 25 C AV = 100 Both channels Channel 1 only, Channel 2 on MAX V/s 0.8 14 Gain margin 8 1 25C Gain-bandwidth product m TYP f = 100 Hz Channel 2 only, Channel 1 on ts MIN 25C 45 25C 7 dB SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO IIB Input offset voltage vs Common-mode input voltage 1, 2 Input bias current vs Free-air temperature 3, 4 IIO VOH Input offset current vs Free-air temperature 3, 4 High-level output voltage vs High-level output current 5, 6 VOL VO(PP) Low-level output voltage vs Low-level output current 7, 8 Peak-to-peak output voltage vs Frequency 9, 10 Open-loop gain vs Frequency 11, 12 Phase vs Frequency 11, 12 Differential voltage amplification vs Load resistance 13 Capacitive load vs Load resistance 14 Zo CMRR Output impedance vs Frequency 15, 16 Common-mode rejection ratio vs Frequency 17 kSVR Supply-voltage rejection ratio vs Frequency 18, 19 AVD IDD Supply current vs Supply voltage 20 vs Free-air temperature 21 Amplifier turnon characteristics 22 Amplifier turnoff characteristics 23 Supply current turnon 24 Supply current turnoff SR 25 Shutdown supply current vs Free-air temperature Slew rate vs Supply voltage 26 27 vs Frequency 28, 29 vs Common-mode input voltage 30, 31 Vn Equivalent input noise voltage THD Total harmonic distortion vs Frequency 32, 33 THD+N Total harmonic distortion plus noise vs Peak-to-peak signal amplitude 34, 35 vs Frequency 11, 12 m Phase margin vs Load capacitance 36 vs Free-air temperature 37 vs Supply voltage 38 vs Free-air temperature 39 Gain bandwidth product Large signal follower 40, 41 Small signal follower 42, 43 Inverting large signal 44, 45 Inverting small signal 46, 47 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 1 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 0 VDD = 5 V TA = 25C 0.8 VIO - Input Offset Voltage - mV VIO - Input Offset Voltage - mV 0.8 1 VDD = 3 V TA = 25C 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 0.5 1 1.5 2 2.5 -1 3 0 VICR - Common-Mode Input Voltage - V 1 Figure 2 VDD = 3 V VI = 1.5 V 4.5 IIB 4 3.5 3 2.5 2 1.5 1 0.5 IIO -15 5 25 5 45 65 85 105 125 6 VDD = 5 V VI = 2.5 V 5 IIB 4 3 2 1 IIO 0 -1 -55 -35 TA - Free-Air Temperature - C -15 5 25 Figure 5 POST OFFICE BOX 655303 45 65 85 TA - Free-Air Temperature - C Figure 4 10 4 INPUT BIAS AND INPUT OFFSET CURRENT vs FREE-AIR TEMPERATURE I IB and I IO - Input Bias and Input Offset Current - nA I IB and I IO - Input Bias and Input Offset Current - nA 5 -0.5 -55 -35 3 Figure 3 INPUT BIAS AND INPUT OFFSET CURRENT vs FREE-AIR TEMPERATURE 0 2 VICR - Common-Mode Input Voltage - V * DALLAS, TEXAS 75265 105 125 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 3 5 VDD = 5 VDC 4.5 2.5 VOH - High-Level Output Voltage - V VOH - High-Level Output Voltage - V VDD = 3 VDC TA = -55C 2 1.5 TA = 125C TA = 85C TA = 25C 1 TA = -40C 0.5 TA = -55C 4 3.5 3 2.5 2 TA = 125C TA = 85C TA = 25C 1.5 TA = -40C 1 0.5 0 0 10 20 30 40 50 60 70 0 80 0 IOH - High-Level Output Current - mA 20 40 60 Figure 6 100 120 140 160 180 200 Figure 7 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 3 4.5 VDD = 3 VDC VDD = 5 VDC 4 2.5 VOL - Low-Level Output Voltage - V VOL - Low-Level Output Voltage - V 80 IOH - High-Level Output Current - mA TA = -40C 2 TA = 25C 1.5 TA = 85C TA = 125C 1 0.5 0 10 20 30 40 50 60 TA = -40C 3 TA = 25C 2.5 TA = 85C TA = 125C 2 1.5 1 TA = -55C 0.5 TA = -55C 0 3.5 70 IOL - Low-Level Output Current - mA 0 0 20 40 60 80 100 120 140 160 IOL - Low-Level Output Current - mA Figure 8 Figure 9 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY 5.5 VDD = 3 V AV = -10 THD = 1% RL = 10 k 2.5 2 1.5 1 0.5 0 10k 100k 1M VDD = 5 V AV = -10 THD = 1% RL = 10 k 5 VO(PP) - Peak-to-Peak Output Voltage - V VO(PP) - Peak-to-Peak Output Voltage - V 3 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 10k 10M 100k f - Frequency - Hz 1M f - Frequency - Hz Figure 10 Figure 11 OPEN-LOOP GAIN AND PHASE vs FREQUENCY 100 VDD = 1.5 V RL = 10 k CL = 0 TA = 25C 90 80 60 0 -20 -40 AVD 50 -60 40 -80 -100 30 Phase 20 -120 10 -140 0 -160 -10 -180 -20 10 100 1k 10k 100k 1M f - Frequency - Hz Figure 12 12 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 -200 10M Phase Open-Loop Gain - dB 70 40 10M SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS OPEN-LOOP GAIN AND PHASE vs FREQUENCY 100 VDD = 2.5 V RL = 10 k CL = 0 TA = 25C 90 80 60 20 0 -20 -40 AVD 50 -60 40 -80 -100 30 Phase 20 -120 10 -140 0 -160 -10 -20 10 Phase Open-Loop Gain - dB 70 40 -180 100 1k 100k 10k 1M -200 10M f - Frequency - Hz Figure 13 DIFFERENTIAL VOLTAGE AMPLIFICATION vs LOAD RESISTANCE CAPACITIVE LOAD vs LOAD RESISTANCE 10000 TA = 25C 160 140 CL - Capacitive Load - pF A VD - Differential Voltage Amplification - V/mV 180 120 VDD = 2.5 V 100 VDD = 1.5 V 80 60 40 Phase Margin < 30 1000 Phase Margin > 30 VDD = 5 V Phase Margin = 30 TA = 25C 20 0 100 1k 10k 100k 1M 100 10 RL - Load Resistance - 100 1k 10k RL - Load Resistance - Figure 15 Figure 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS OUTPUT IMPEDANCE vs FREQUENCY 1000 OUTPUT IMPEDANCE vs FREQUENCY 1000 VDD = 1.5 V TA = 25C 100 Zo - Output Impedance - Zo - Output Impedance - 100 10 AV = 100 1 AV = 10 0.1 VDD = 2.5 V TA = 25C AV = 1 10 AV = 100 1 AV = 10 0.1 AV = 1 0.01 100 1k 10k 100k 1M 0.01 100 10M 1k f - Frequency - Hz 10k Figure 16 Figure 17 COMMON-MODE REJECTION RATIO vs FREQUENCY CMRR - Common-Mode Rejection Ratio - dB 90 85 80 VDD = 5 V VIC = 2.5 V 75 VDD = 3 V VIC = 1.5 V 70 65 60 10 100 1k 10k 100k 1M f - Frequency - Hz Figure 18 14 100k f - Frequency - Hz POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10M 1M 10M SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 90 +kSVR VDD = 1.5 V TA = 25C 100 k SVR - Supply Voltage Rejection Ratio - dB k SVR - Supply Voltage Rejection Ratio - dB 110 90 -kSVR 80 70 60 +kSVR 50 -kSVR 40 10 100 1k 10k 100k 1M +kSVR 80 -kSVR 70 60 +kSVR 50 -kSVR 40 10 10M VDD = 2.5 V TA = 25C 100 1k f - Frequency - Hz 10k 100k 1M 10M f - Frequency - Hz Figure 19 Figure 20 SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 0.8 0.80 IDD = 125C I DD - Supply Current - mA I DD - Supply Current - mA 0.75 IDD = 85C 0.7 0.6 0.5 0.40 IDD = 25C 0.30 IDD = -55C VDD = 5 V VI = 2.5 V 0.65 0.60 0.55 VDD = 3 V VI = 1.5 V 0.50 0.45 0.40 IDD = -40C 0.20 0.70 0.35 0.10 2.5 3 3.5 4 4.5 5 5.5 6 0.30 -55 -35 VDD - Supply Voltage - V -15 5 25 45 65 85 105 125 TA - Free-Air Temperature - C Figure 21 Figure 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS AMPLIFIER WITH A SHUTDOWN PULSE TURNON CHARACTERISTICS AMPLIFIER WITH A SHUTDOWN PULSE TURNOFF CHARACTERISTICS 5 5 4 Shutdown Pin 3 2 1 0 Amplifier Output 3 2 1 0 -5 VDD = 5 V RL = 10 k AV = 1 TA = 25C Shutdown Pin 3 VSD - Shutdown Voltage - V VSD - Shutdown Voltage - V 4 VDD = 5 V RL = 10 k AV = 1 TA = 25C -3 -1 2 1 0 Amplifier Output 3 2 1 1 3 5 9 7 0 -5 11 -3 -1 t - Time - s 1 t - Time - s Figure 24 Figure 23 SUPPLY CURRENT WITH A SHUTDOWN PULSE TURNON CHARACTERISTICS 1 5.5 0.8 4.5 0.6 3.5 Supply Current 0.4 2.5 0.2 1.5 VDD = 5 V VI = 2.5 V AV = 1 TA = 25C 0 -0.2 -0.4 -0.2 0 0.2 0.4 t - Time - s Figure 25 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 0.5 -0.5 0.6 VSD - Shutdown Voltage - V I DD - Supply Current - mA Shutdown Pin 3 5 7 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS TURNOFF SUPPLY CURRENT WITH A SHUTDOWN PULSE 1 5.5 4.5 0.6 0.4 3.5 Supply Current 2.5 0.2 1.5 0 0.5 -0.2 -0.4 -0.2 0 0.2 VSD - Shutdown Voltage - V Shutdown Pin 0.8 I DD - Supply Current - mA VDD = 5 V VI = 2.5 V AV = 1 TA = 25C -0.5 0.6 0.4 t - Time - s Figure 26 SLEW RATE vs SUPPLY VOLTAGE 3 1.8 2.5 1.75 1.7 VDD = 5 V VI = 2.5 V 2 SR - Slew Rate - V/ s I DD - Shutdown Supply Current - A SHUTDOWN SUPPLY CURRENT vs FREE-AIR TEMPERATURE 1.5 1 VDD = 3 V VI = 1.5 V 0.5 0 SR+ 1.65 1.6 1.55 1.5 1.45 1.4 -0.5 -1 -55 -35 1.35 -15 5 25 45 65 85 105 125 SR- 1.3 2.5 VO(PP) = 2 V CL = 160 pF AV = 1 RL = 10 k TA = 25C 3 TA - Free-Air Temperature - C 3.5 4 4.5 5 5.5 6 VDD - Supply Voltage - V Figure 28 Figure 27 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 18 VDD = 3 V AV = 10 VI = 1.5 V TA = 25C 17 Vn - Equivalent Input Noise Voltage - nV/ Hz Vn - Equivalent Input Noise Voltage - nV/ Hz 18 16 15 14 13 12 11 10 100 1k 10k VDD = 5 V AV = 10 VI = 2.5 V TA = 25C 17 16 15 14 13 12 11 10 100 100k 1k f - Frequency - Hz Figure 29 EQUIVALENT INPUT NOISE VOLTAGE vs COMMON-MODE INPUT VOLTAGE 20 20 VDD = 3 V AV = 10 f = 1 kHz TA = 25C 15 Vn - Equivalent Input Noise Voltage - nV/ Hz Vn - Equivalent Input Noise Voltage - nV/ Hz 100k Figure 30 EQUIVALENT INPUT NOISE VOLTAGE vs COMMON-MODE INPUT VOLTAGE 14 13 12 11 10 0 0.5 1 1.5 2 2.5 3 VICR - Common-Mode Input Voltage - V VDD = 5 V AV = 10 f = 1 kHz TA = 25C 15 14 13 12 11 10 0 1 2 Figure 32 POST OFFICE BOX 655303 3 4 VICR - Common-Mode Input Voltage - V Figure 31 18 10k f - Frequency - Hz * DALLAS, TEXAS 75265 5 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION vs FREQUENCY 1 VDD = 1.5 V VO(PP) = 2 V RL = 10 k THD - Total Harmonic Distortion - % THD - Total Harmonic Distortion - % 0.5 TOTAL HARMONIC DISTORTION vs FREQUENCY AV = 100 0.1 AV = 10 0.010 0.001 AV = 1 10 100 1k 10k 0.1 AV = 100 AV = 10 0.010 AV = 1 0.001 100k VDD = 2.5 V VO(PP) = 4 V RL = 10 k 10 100 1k f - Frequency - Hz Figure 33 THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % TOTAL HARMONIC DISTORTION PLUS NOISE vs PEAK-TO-PEAK SIGNAL AMPLITUDE 1 RL = 250 RL = 2 k 0.1 RL = 10 k 0.010 RL = 100 k 0.001 1 1.2 1.4 1.6 1.8 2 100k Figure 34 TOTAL HARMONIC DISTORTION PLUS NOISE vs PEAK-TO-PEAK SIGNAL AMPLITUDE VDD = 3 V AV = 1 TA = 25C 10k f - Frequency - Hz 2.2 2.4 2.6 2.8 3 3.2 1 RL = 250 RL = 2 k 0.1 RL = 10 k 0.010 RL = 100 k VDD = 5 V AV = 1 TA = 25C 0.001 4 4.1 4.2 Peak-to-Peak Signal Amplitude - V 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5 Peak-to-Peak Signal Amplitude - V Figure 35 Figure 36 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS PHASE MARGIN vs LOAD CAPACITANCE PHASE MARGIN vs FREE-AIR TEMPERATURE 90 80 RL = 10 k CL = 160 pF 55 70 m - Phase Margin - degrees m - Phase Margin - degrees 60 VDD = 2.5 V TA = 25C RL = 10 k Rnull = 50 60 50 40 Rnull = 20 30 20 Rnull = 0 50 VDD = 2.5 V 45 VDD = 1.5 V 40 35 10 0 100 10 1k 30 -55 -35 100k 10k CL - Load Capacitance - pF -15 Figure 37 45 65 85 105 125 GAIN BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE 5 5 CL = 160 pF RL = 10 k f = 10 kHz TA = 25C 4.75 Gain Bandwidth Product - MHz Gain Bandwidth Product - MHz 25 Figure 38 GAIN BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 4.75 5 TA - Free-Air Temperature - C 4.5 4.25 4 3.75 4.5 RL = 10 k CL = 160 pF VDD = 2.5 V 4.25 4 3.75 3.5 VDD = 1.5 V 3.25 3.5 2.5 3 3.5 4 4.5 5 5.5 6 3 -55 -35 VDD - Supply Voltage - V Figure 39 20 -15 5 25 Figure 40 POST OFFICE BOX 655303 45 65 85 TA - Free-Air Temperature - C * DALLAS, TEXAS 75265 105 125 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS LARGE SIGNAL FOLLOWER LARGE SIGNAL FOLLOWER 2.2 3.7 2 3.3 VO - Voltage - V Input VO - Voltage - V Input 1.8 Output 1.6 1.4 VDD = 3 V VI(PP) = 1 V VI = 1.5 V RL = 10 k CL = 160 pF AV = 1 TA = 25C 1.2 1 0.8 -2 0 2 4 6 Input 2.9 Output 2.5 VDD = 5 V VI(PP) = 2 V VI = 2.5 V RL = 10 k CL = 160 pF AV = 1 TA = 25C 2.1 Output 1.7 8 10 12 14 16 1.3 -2 18 0 2 4 6 t - Time - s 8 10 12 14 16 18 Figure 42 SMALL SIGNAL FOLLOWER SMALL SIGNAL FOLLOWER 1.6 2.6 1.55 2.55 VO - Voltage - V VO - Voltage - V Output t - Time - s Figure 41 Input 1.5 Output 1.45 1.4 -0.2 Input Input 2.5 Output 2.45 VDD = 3 V VI(PP) = 100 mV CL = 160 pF AV = 1 VI = 1.5 V TA = 25C RL = 10 k 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2.4 -0.2 VDD = 5 V VI(PP) = 100 mV VI = 2.5 V RL = 10 k 0 t - Time - s 0.2 0.4 0.6 CL = 160 pF AV = 1 TA = 25C 0.8 1 1.2 1.4 1.6 1.8 t - Time - s Figure 43 Figure 44 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 TYPICAL CHARACTERISTICS INVERTING LARGE SIGNAL INVERTING LARGE SIGNAL 4 2.3 Input 2.1 Input 3.5 VDD = 3 V VI(PP) = 1 V VI = 1.5 V RL = 10 k CL = 160 pF AV = -1 TA = 25C 1.7 1.5 1.3 VO - Voltage - V VO - Voltage - V 1.9 1.1 VDD = 5 V VI(PP) = 2 V VI = 2.5 V RL = 10 k CL = 160 pF AV = -1 TA = 25C 3 2.5 2 Output 0.9 Output 1.5 0.7 0.5 -0.2 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1 -0.2 1.6 1.8 0 0.2 0.4 t - Time - s 0.6 Figure 45 INVERTING SMALL SIGNAL 1.6 1.8 INVERTING SMALL SIGNAL Input Input 2.55 VDD = 3 V VI(PP) = 100 mV VI = 1.5 V RL = 10 k CL = 160 pF AV = -1 TA = 25C 1.5 VO - Voltage - V VO - Voltage - V 1.2 1.4 2.6 1.55 1.45 VDD = 5 V VI(PP) = 100 mV VI = 2.5 V RL = 10 k CL = 160 pF AV = -1 TA = 25C 2.5 2.45 Output 0 0.2 0.4 0.6 0.8 Output 1 1.2 1.4 1.6 1.8 2.4 -0.2 0 t - Time - s 0.2 0.4 0.6 0.8 1 t - Time - s Figure 47 22 1 Figure 46 1.6 1.4 -0.2 0.8 t - Time - s Figure 48 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1.2 1.4 1.6 1.8 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 PARAMETER MEASUREMENT INFORMATION Rnull _ + RL CL Figure 49 APPLICATION INFORMATION driving a capacitive load When the amplifier is configured in this manner, capacitive loading directly on the output will decrease the device's phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater than 10 pF, it is recommended that a resistor be placed in series (RNULL) with the output of the amplifier, as shown in Figure 49. A minimum value of 20 should work well for most applications. RF RG RNULL _ Input Output + CLOAD Figure 50. Driving a Capacitive Load offset voltage The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times the corresponding gains. The following schematic and formula can be used to calculate the output offset voltage: RF IIB- RG + - VI IIB+ V OO +V IO 1) R R F G VO + RS "I IB) R S 1) R R F G "I IB- R F Figure 51. Output Offset Voltage Model POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 APPLICATION INFORMATION general configurations When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier (see Figure 51). RG RF - VO + VI R1 C1 f V O + V I 1) R R F G -3dB + 1 2pR1C1 1 1 ) sR1C1 Figure 52. Single-Pole Low-Pass Filter If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth. Failure to do this can result in phase shift of the amplifier. C1 + _ VI R1 R1 = R2 = R C1 = C2 = C Q = Peaking Factor (Butterworth Q = 0.707) R2 f C2 RG RF RG = Figure 53. 2-Pole Low-Pass Sallen-Key Filter 24 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 -3dB + ( 1 2pRC RF 1 2- Q ) SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 APPLICATION INFORMATION shutdown function Two members of the TLV246x family (TLV2460/3) have a shutdown terminal for conserving battery life in portable applications. When the shutdown terminal is tied low, the supply current is reduced to 0.3 A/channel, the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to VDD/2. Therefore, when operating the device with split supply voltages (e.g. 2.5 V), the shutdown terminal needs to be pulled to VDD- (not GND) to disable the operational amplifier. The amplifier's output with a shutdown pulse is shown in Figures 22, 23, 24, and 25. The amplifier is powered with a single 5-V supply and configured as a noninverting configuration with a gain of 5. The amplifier turnon and turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output waveform. The times for the single, dual, and quad are listed in the data tables. circuit layout considerations To achieve the levels of high performance of the TLV246x, follow proper printed-circuit board design techniques. A general set of guidelines is given in the following. D Ground planes - It is highly recommended that a ground plane be used on the board to provide all components with a low inductive ground connection. However, in the areas of the amplifier inputs and output, the ground plane can be removed to minimize the stray capacitance. D Proper power supply decoupling - Use a 6.8-F tantalum capacitor in parallel with a 0.1-F ceramic capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers depending on the application, but a 0.1-F ceramic capacitor should always be used on the supply terminal of every amplifier. In addition, the 0.1-F capacitor should be placed as close as possible to the supply terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less effective. The designer should strive for distances of less than 0.1 inches between the device power terminals and the ceramic capacitors. D Sockets - Sockets can be used but are not recommended. The additional lead inductance in the socket pins will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board is the best implementation. D Short trace runs/compact part placements - Optimum high performance is achieved when stray series inductance has been minimized. To realize this, the circuit layout should be made as compact as possible, thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at the input of the amplifier. D Surface-mount passive components - Using surface-mount passive components is recommended for high performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be kept as short as possible. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 APPLICATION INFORMATION general power dissipation considerations For a given JA, the maximum power dissipation is shown in Figure 53 and is calculated by the following formula: P D + Where: T -T MAX A q JA PD = Maximum power dissipation of THS246x IC (watts) TMAX = Absolute maximum junction temperature (150C) TA = Free-ambient air temperature (C) JA = JC + CA JC = Thermal coefficient from junction to case CA = Thermal coefficient from case to ambient air (C/W) MAXIMUM POWER DISSIPATION vs FREE-AIR TEMPERATURE 2 Maximum Power Dissipation - W 1.75 PDIP Package Low-K Test PCB JA = 104C/W 1.5 1.25 TJ = 150C MSOP Package Low-K Test PCB JA = 260C/W SOIC Package Low-K Test PCB JA = 176C/W 1 0.75 0.5 0.25 SOT-23 Package Low-K Test PCB JA = 324C/W 0 -55 -40 -25 -10 5 20 35 50 65 80 95 110 125 TA - Free-Air Temperature - C NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB. Figure 54. Maximum Power Dissipation vs Free-Air Temperature 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using Microsim Parts Release 8, the model generation software used with Microsim PSpice . The Boyle macromodel (see Note 2) and subcircuit in Figure 54 are generated using the TLV246x typical electrical and operating characteristics at TA = 25C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): D D D D D D D D D D D D Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit NOTE 2: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling of Intergrated Circuit Operational Amplifiers", IEEE Journal of Solid-State Circuits, SC-9, 353 (1974). 99 EGND + R2 3 VDD + - + ISS RSS CSS VD - 53 RP 10 2 IN - J1 FB 6 7 + 9 VLIM + VB 8 GA GCM J2 - - DC RO1 OUT IN + 1 11 12 RD1 5 DLN DE 92 54 C1 DP + RD2 VE GND RO2 C2 .SUBCKT TLV246X 1 2 3 4 5 C1 11 12 2.46034E-12 C2 6 7 10.0000E-12 CSS 10 99 443.21E-15 DC 5 53 DY DE 54 5 DY DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP + VLN 0 21.600E6 -1E3 1E3 22E6 -22E6 GA 6 0 11 12 345.26E-6 GCM 0 6 10 99 15.4226E-9 ISS 10 4 DC 18.850E-6 HLIM 90 0 VLIM 1K J1 11 2 10 JX1 J2 12 1 10 JX2 R2 6 9 100.00E3 - - - + 90 HLIM - 4 + DLP 91 + VLP VLN RD1 3 11 2.8964E3 RD2 3 12 2.8964E3 R01 8 5 5.6000 R02 7 99 6.2000 RP 3 4 8.9127 RSS 10 99 10.610E6 VB 9 0 DC 0 VC 3 53 DC .7836 VE 54 4 DC .7436 VLIM 7 8 DC 0 VLP 91 0 DC 117 VLN 0 92 DC 117 .MODEL DX D (IS=800.00E-18) .MODEL DY D (IS=800.00E-18 Rs = 1m Cjo=10p) .MODEL JX1 NJF (IS=1.0000E-12 BETA=6.3239E-3 + VTO= -1) .MODEL JX2 NJF (IS=1.0000E-12 BETA=6.3239E-3 + VTO= -1) .ENDS Figure 55. Boyle Macromodels and Subcircuit PSpice and Parts are trademarks of MicroSim Corporation. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 SGLS132C - AUGUST 2002 - REVISED OCTOBER 2005 macromodel information (continued) .subckt TLV_246Y 1 2 3 4 5 6 c1 11 12 2.4603E-12 c2 72 7 10.000E-12 css 10 99 443.21E-15 dc 70 53 dy de 54 70 dy dlp 90 91 dx dln 92 90 dx dp 4 3 dx egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5 fb 7 99 poly(5) vb vc ve vlp vln 0 21.600E6 -1E3 1E3 22E6 -22E6 ga 72 0 11 12 345.26E-6 gcm 0 72 10 99 15.422E-9 iss 74 4 dc 18.850E-6 hlim 90 0 vlim 1K j1 11 2 10 jx1 j2 12 1 10 jx2 r2 72 9 100.00E3 rd1 3 11 2.8964E3 rd2 3 12 2.8964E3 ro1 8 70 5.6000 ro2 7 99 6.2000 rp 3 71 8.9127 rss 10 99 10.610E6 rs1 6 4 1G rs2 6 4 1G rs3 6 4 1G rs4 6 4 1G s1 71 4 6 4 s1x s2 70 5 6 4 s1x s3 10 74 6 4 s1x s4 74 4 6 4 s2x vb 9 0 dc 0 vc 3 53 dc .7836 ve 54 4 dc .7436 vlim 7 8 dc 0 vlp 91 0 dc 117 vln 0 92 dc 117 .model dx D(Is=800.00E-18) .model dy D(Is=800.00E-18 Rs=1m Cjo=10p) .model jx1 NJF(Is=1.0000E-12 Beta=6.3239E-3 Vto=-1) .model jx2 NJF(Is=1.0000E-12 Beta=6.3239E-3 Vto=-1) .model s1x VSWITCH(Roff=1E8 Ron=1.0 Voff=2.5 Von=0.0) .model s2x VSWITCH(Roff=1E8 Ron=1.0 Voff=0 Von=2.5) .ends Figure 54. Boyle Macromodels and Subcircuit (Continued) 28 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TLV2462AMDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV2462AQDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV2464AMDREP ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV2464AMDREPG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV2464AMPWREP ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03619-03XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03619-06XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03619-07YE ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03619-07ZE ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TLV2462A-EP, TLV2464A-EP : * Catalog: TLV2462A, TLV2464A Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2009 TLV2462A-Q1, TLV2464A-Q1 * Automotive: Military: TLV2462AM * NOTE: Qualified Version Definitions: - TI's standard catalog product * Catalog - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Automotive * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing TLV2462AMDREP SOIC D SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLV2462AQDREP SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLV2464AMDREP SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLV2464AMPWREP TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV2462AMDREP SOIC D 8 2500 367.0 367.0 35.0 TLV2462AQDREP SOIC D 8 2500 367.0 367.0 35.0 TLV2464AMDREP SOIC D 14 2500 333.2 345.9 28.6 TLV2464AMPWREP TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated