G7F01144C - THERMODISC - Datasheet.Live

Upper Limit Temperature Protection

MICROTEMP®thermal cutoffs from Therm-O-Disc offer an accurate, reliable solution to the

need for upper limit temperature protection. Known as a thermal fuse, thermal link, or TCO, the

MICROTEMP® thermal cutoff provides protection against overheating by interrupting an electrical

circuit when operating temperatures exceed the rated temperature of the cutoff.

MICROTEMP® Features:

• One-shot operation cuts off electrical power

• Current interrupt capacity up to 25 amps @ 250VAC

• Low resistance

• Compact size

Operating Principle of the MICROTEMP® TCO

The active trigger mechanism of the thermal cutoff is an exclusively formulated, electrically

nonconductive pellet. Under normal operating temperatures, the solid pellet holds spring-loaded

contacts closed.

When a predetermined temperature is reached, the pellet melts, allowing the compression spring

to relax. The trip spring then slides the contact away from the lead and the circuit is opened (see

figures 1 and 2).

After a MICROTEMP® thermal cutoff opens a circuit, the TCO needs to be replaced. This

replacement procedure must include correction of the fault condition before the product is

operated again.

MICROTEMP® Thermal Cutoffs:

INTRODUCTION

THERMAL

PELLET

COMPRESSION

SPRING

TRIP SPRING

CERAMIC

BUSHING

CASE AND LEAD

ASSEMBLY

DISCS

STAR CONTACT

ISOLATED

LEAD

Before Operation

Grey area shows

current path

EPOXY

SEAL

COMPRESSION

SPRING

TRIP SPRING

CERAMIC

BUSHING

CASE AND LEAD

ASSEMBLY

DISCS

STAR CONTACT

ISOLATED

LEAD

After Operation

Grey area shows opened or

broken current path

EPOXY

SEAL

MICROTEMP® G4, G6 & G7 Series TCO

THERMAL

PELLET

COMPRESSION

SPRING

TRIP SPRING

CERAMIC

BUSHING

CASE AND LEAD

ASSEMBLY

DISCS

STAR CONTACT

FLOATING

CONTACT

Before Operation

Grey area shows

current path

ISOLATED LEAD

EPOXY

SEAL

COMPRESSION

SPRING

TRIP SPRING

CERAMIC

BUSHING

CASE AND LEAD

ASSEMBLY

DISCS

STAR CONTACT

ISOLATED LEAD

After Operation

Grey area shows opened or

broken current path

FLOATING

CONTACT

EPOXY

SEAL

MICROTEMP® G5 & G8 Series TCO

Figure 1

Figure 2

MICROTEMP® thermal cutoffs are available in a range of temperatures and electrical ratings to meet

application requirements (see Microtemp® Operating Temperature Summary and Electrical Rating

Summary on page 4). There are 5 primary types of thermal cutoffs available. Standard dimensions

of each TCO series are shown on page 4.

G Series: This “Global” series or G designation represents the world standard in thermal cutoffs.

MICROTEMP®TCOs were the first chemical-pellet spring-type TCO ever developed and continue to be

the thermal cutoff of choice for over 35 years.

E Series: This new “Environmentally” friendly series holds Agency recognition equivalent to the G

series and has been designed to comply with the Restriction of Hazardous Substances in Electrical

and Electronic Equipment (ROHS) Directive (2002/95/EC). None of the substances specified in this

Directive have been intentionally incorporated into the E-series products.

G4 Series

Rated for continuous operating currents up to 10 amps @ 250VAC (15 amps @ 120VAC, 5 amps @

24VDC), the G4 series MICROTEMP® TCO is the industry standard for over-temperature protection.

The G4 series is applied to millions of appliances and personal care products each year, providing

reliable back-up protection for temperature controlling thermostats and other over-temperature

conditions. The G4 series is also widely applied in office machines, portable heaters and industrial

equipment as a thermal safeguard.

G5 Series

Designed for higher voltage and current applications than the G4, the G5 series MICROTEMP®

TCO is rated for operating currents up to 20 amps @ 250VAC and 277 VAC (25 amps @ 120VAC).

Similar in appearance to the G4 series, the G5 series has a different internal construction designed

for interrupting higher currents and withstanding higher temperatures.

G6 Series

The G6 series MICROTEMP® TCO can be utilized in applications where a higher maximum-overshoot

temperature rating is not required, yet it is rated for operating currents up to 16 amps @ 250VAC. It

is the same physical size as the G4, G5 and G8 series TCOs.

G7 Series

The G7 series MICROTEMP® TCO is designed to satisfy applications requiring miniaturized components

that do not need maximum current interrupt capability. The G7 is just 2/3 the size of the G4 and G5,

and with a current interrupting capability of 5 amps @ 250VAC (5 amps @ 24VDC), it is capable of

meeting the requirements of transformers, motors, battery packs and electronic circuit applications.

G8 Series

Designed for very high-current applications such as major appliances and high-wattage electric heat

packages, the G8 series MICROTEMP® TCO is rated for operating currents up to 25 amps @ 250VAC

(20 amps @ 277VAC). More economical than electromechanical bimetal-type one shot devices, it can

be utilized in applications where its small size is an advantage in terms of mounting (it’s the same

physical size as the G4, G5 and G6 series TCOs) and thermal response. 3

MICROTEMP® Thermal Cutoffs:

TYPES & SPECIFICATIONS

Tm– Maximum overshoot temperature:

temperature up to which TCO will

not change status

Tf– Functioning open temperature

tolerance: +0, -5°C

Th– Maximum temperature of the

MICROTEMP® TCO measured at the

case end of the thermal cutoff at

which the thermal cutoff can be

maintained for a period for 168

hours without opening.

NOTE: it is advised that TCOs are not

exposed to continuous operating

temperatures in excess of Tf -25°C.

C.T.I. – Comparative tracking index

(all primary thermal cutoffs):

250VAC

NOTE: G4, G5, G6 ,G7 and G8 series TCOs

with TF 175°C comply with UL

conductive heat aging (CHAT)

requirements.

Dimensions – Inches (millimeters) G4, G5, G6 & G8 Series G7 Series

Standard A Overall Length ± .12 (±3.0) 2.51 (63.8) N/A

Leads B Case Lead Length ± .06 (± 1.5) 1.38 (34.9) N/A

Long A Overall Length ± .12 (±3.0) 3.26 (82.9) 3.26 (82.9)

Leads B Case Lead Length ± .06 (± 1.5) 1.38 (34.9) 1.38 (34.9)

C Case Lead Diameter 0.040 (1.0) 0.023 (.57)

Lead Material C Case Lead Material Tin-Plated Copper Tin-Plated Copper

and Diameter D Epoxy Lead Diameter 0.040 (1.0) 0.023 (.57)

D Epoxy Lead Material Silver-Plated Copper Silver-Plated Copper

Case E Case Length (Reference) 0.58 (14.7) 0.38 (9.6)

Dimensions F Case Diameter (Reference) 0.158 (4.0) 0.118 (3.0)

Electrical Current & Voltage Rating

G4 Series G5 Series G6 Series G7 Series G8 Series R9 Series R7 Series

Resistive Inductive Resistive Resistive Resistive Inductive Resistive Resistive Resistive

UL/CSA 10A/250VAC 8A/250VAC 20A/250VAC 16A/250VAC 5A/250VAC 4.5A/250VAC 25A/250VAC — —

15A/120VAC 14A/120VAC 25A/120VAC 5A/24VDC 4.5A/120VAC

5A/24VDC 21A/240VAC

20A/277VAC

VDE 10A/250VAC 8A/250VAC 20A/250VAC 16A/250VAC 5A/250VAC 4.5A/250VAC 25A/250VAC — —

15A/120VAC 14A/120VAC 5A/24VDC 4.5A/120VAC

5A/24VDC

METI 10A/250VAC — 15A/250VAC 15A/250VAC 5A/250VAC — — 15A/250VAC 7A/250VAC

5A/24VDC 7A/24VDC

CCC 10A/250VAC — 16A/250VAC — 5A/250VAC — — — —

Agency

MICROTEMP® TCO Operating Temperature Summary

MICROTEMP® TCO

Standard Dimensions

Electrical Rating Summary

Open

Temp

Tf °C

Holding

Temperature °C Maximum Overshoot Temperature °C

Th °C

G4, G5, G7

Series

Th °C

G6, G8

Series

Tm °C

Series

Tm °C

Series

Tm °C

Series

Tm °C

Series

Tm °C

Series

Tm °C

R9 Series

Tm °C

R7 Series

070 55 45 130 175 130 125 175 130 125

072 57 47 100 175 100 — 175 100 —

073 58 48 130 175 100 — 175 130 130

075 — — 125 190 — 125 — 125 125

077 62 52 125 200 125 125 200 125 125

081 — — 125 200 ---- 125 — 125 125

084 69 59 125 200 125 125 200 125 125

087 — — 140 — — 140 — 140 140

093 78 68 140 215 — 140 215 140 140

098 83 73 140 215 140 140 215 140 140

100 — — — 215 — 130 — — 130

104 89 79 150 225 150 — 225 150 —

110 95 85 150 225 — 140 225 150 140

115 — — 160 235 — 140 — 160 140

117 102 92 160 235 160 150 235 160 150

121 106 96 160 235 160 150 235 160 150

125 — — 185 235 — 150 — 185 150

128 113 103 205 235 205 150 235 160 150

134 — — 205 250 — 175 — 205 175

141 — — 205 250 — 175 — 205 175

144 129 119 240 250 240 175 250 175 175

147 — — 205 240 — 175 — 205 175

152 137 127 205 250 205 175 — 175 175

158 — — 240 285 — 200 — 240 200

167 152 142 240 285 240 200 285 210 200

172 — — 240 350 — 200 — 240 200

184 169 159 210 350 210 200 350 210 200

190 — — 310 350 — 270 — 310 270

192 177 167 210 350 210 — 350 210 210

205 — — 310 375 — 300 — 310 300

216 200 191 375 375 — — — 375 —

229 200 200 375 375 375 — 375 375 —

240 200 200 450 375 450 — 375 375 —

Packaged Thermal Cutoffs

Therm-O-Disc also offers a variety of packaging options for MICROTEMP® thermal cutoffs.

Therm-O-Disc offers two standard packages with wide application in the HVAC industry. Primarily

designed for heating applications, the GXAM04 and GXAM06 packages mount a standard G4, G5,

G6 or G8 TCO in a high temperature ceramic base (see figure 3).

The popular GXAP Potted TCO packages consist of a TCO epoxy-potted into a plastic insulating

mounting case. The assembly can be supplied with various case materials, shapes and terminations.

They can be used to accurately sense temperature as probes and as surface, airstream and ambient

sensors (see figure 4). They can be easily replaced in the field without disturbing the rest of the circuit.

Custom packages, insulations or special assemblies may be specified to meet specific unique

application needs. By taking advantage of our technical expertise and high volume production

methods and equipment, we can provide significant savings on custom packages.

Packaged TCO Material Specifications

Figure 4

GXAP04

GXAP02

GXAP12

GXAP05

Type Base Material Material Rating Maximum TCO

Temperature °C Temperature °C

GXAP01 PBT Glass Filled 120 134

GXAP02 PPS Glass Filled 220 192

GXAP04 PBT Glass Filled 120 134

GXAP05 PBT Glass Filled 120 134

GXAP10 PPS Mineral Filled 220 192

GXAP12 PBT Glass Filled 120 134

GXAM04 Ceramic DIN VDE 0335, C 221 >250 260

GXAM06 Ceramic DIN VDE 0335, C 221 >250 260

GXAM11 PBT 120 134

Figure 3

GXAM04

GXAM06

*Additional ratings available upon request.

GXAM11

Lead Configurations

The MICROTEMP® TCO can be furnished with virtually any lead configuration specified for an

application. Lead curls are available to match most sizes of screws along with varying lead lengths

and lead forms.

All types of terminations, such as quick connects, ring terminals and blade terminals, are available

at additional cost. In addition, tape and reel packaging can be specified to meet high volume

requirements.

Temperature Ratings

MICROTEMP® thermal cutoffs are available in a wide range of opening temperatures, providing

designers a high degree of flexibility (see Microtemp® TCO Operating Temperature Summary at

the top of page 4). Determining the correct TCO temperature calibration requires significant

application testing.

The proper calibration will be affected by application variables such as I2R self heating of the

TCO, heat transfer through insulation and heat dissipation due to heat sinking and air flow.

Thermocoupled TCO Test Samples (TTTS), that match the physical and electrical characteristics

of a functional TCO, are available to help evaluate application specific variables.

For more information on testing and installing MICROTEMP® TCOs, please review the

MICROTEMP® Thermal Cutoff Application Notes section.

Direct Current (DC) Applications

The G4 and G7 series MICROTEMP® thermal cutoffs have published electrical ratings for direct

current (DC) applications. Current interruption capacity in DC circuits is highly application sensitive.

Therm-O-Disc recommends thorough testing of DC electrical applications using the testing

guidelines in Therm-O-Disc’s MICROTEMP® thermal cutoff technical information section.

Samples and Quotations

MICROTEMP® TCO samples and Thermocoupled TCO Test Samples (TTTS) are readily

available for determining the correct response and desired performance in an application.

For more information on MICROTEMP® TCOs, call a Therm-O-Disc sales engineer at 419-525-8300.

Lead Cutting

Dimension A Dimension B Dimension C

0.95 (24.2) 0.22 (5.6) 0.73 (18.6)

DIM. A

DIM. C DIM. B

Minimum Dimensions

Inches (millimeters)

Tape and Reel Packaging

F0.060(1.5)

DIM. A

DIM. B

DIM. F

0.031(0.8)

(PITCH MEASURED AT TAPE ON MICROTEMP SIDE)

DIM. D

DIM. C

Dimensions

Inches (millimeters)

Item Dim. A Dim. B Dim. C Dim. D Dim. E Dim. F

GXAA0900TTTC 1.66 (42.1) 2.80 (71.1) 1.38 (35.1) 3.26 (82.8) 3.60 (91.4) 0.200 (5.1)

G7FA0900TTTC 1.66 (42.1) 2.80 (71.1) 1.38 (35.1) 3.26 (82.8) 3.60 (91.4) 0.197 (5.0)

Product Nomenclature

MICROTEMP® TCO

MICROTEMP® TCO Packages

G Z X X XX RR TTTC

G – Rating type

(G – Global, Y-Non Agency)

Z – Internal construction

(4, 5, 6, 7, 8, 9)

– Case material and lead wire

(A, C, D, F)

TTTC – Maximum

open temperature in °C

RR – Assembly modifications

(Plating, terminal bend, stenciling)

XX – Specific package construction

(00-99)

X – General packages TCO type

(Configuration, potted, mounting base, etc.)

As shown above, Therm-O-Disc MICROTEMP® TCOs follow a consistent product nomenclature that identifies the basic

product type, lead wire size, special features and packaging options. For example, a standard G4 series TCO calibrat-

ed to open at 192°C would have a part number G4A00192C.

MICROTEMP® TCO Product Markings

Primary TCOs Secondary Packages

XXXXXXXX Special customer identification XXXXXXXXX Special customer identification

(when required, up to 9 characters) (when required, up to 9 characters)

MICROTEMP®Registered trademark MICROTEMP®Registered trademark

P ZZZZZ (P) Manufacturing plant; (may be T-O-D)

(ZZZZZ) Date code G Z X XX RR Part number (see figure 7)

G Z X XX Part number (see figure 7) TF TTTC P ZZ (TF TTTC) Maximum open temperature °C;

TF TTTC ( ) Underwriters Labs logo; (P) Manufacturing plant location;

(TF TTTC) Maximum open (ZZ) Manufacture date code;

temperature °C ( ) Underwriters Labs logo

MICROTEMP® thermal cutoffs, available in a variety of standard and custom configurations, provide

reliable one-shot, over-temperature protection in a wide range of applications. Performance can

be affected by installation method and proper location of the thermal cutoff. Both application and

installation are important in the overall performance of the product, and thorough testing is neces-

sary for both AC and DC applications. The following guidelines will answer most questions concern-

ing these two subjects.

Application of Thermal Cutoffs

A thermal measurement procedure that utilizes a Thermocoupled TCO Test Sample (TTTS) can

assist in determining the appropriate calibration temperature and design location of MICROTEMP®

thermal cutoffs. The TTTS matches the electrical characteristics of the thermal cutoff but does not

have thermally responsive parts. The TTTS is supplied with a thermocouple attached to the case of

the thermal cutoff (see figure 5).

Figure 5

View of required thermocouple attachment before soldering

Dummy cutoffs can be supplied with Type J, Type T or Type K thermocouples. Other thermocouple

types can usually be supplied upon request at a nominal charge.

Location

Sufficient time and effort must be used to determine the proper and most desirable location for a

thermal cutoff. The employment of infrared thermography, or a sufficient number of thermocouples

to identify the highest temperature areas in the product requiring protection during normal operation

and fault conditions, should be considered. The location that provides the largest differential

between these two conditions is generally most desirable.

MICROTEMP® Thermal Cutoff

APPLICATION NOTES

Calibration Temperature

It is necessary to select a thermal cutoff rating above the maximum temperature experienced during

normal operation, including expected short-term temperature overshoots. The temperatures

experienced by the thermal cutoff during normal operation will determine the life expectancy

for the thermal cutoff. If the thermal cutoff rating is too close to the temperature experienced

during normal operation (including overshoot temperatures after opening of a thermostat, etc.),

the probability of a nuisance trip increases. Nuisance trips are caused by pellet shrinkage due to

repeated operation at temperatures near but below calibration temperature, or excessive thermal

gradients across the case of the TCO and its leads (see “Thermal Gradients”).

Therm-O-Disc has compiled standard life curves by subjecting MICROTEMP® thermal cutoffs to very

controlled temperatures for extended time periods under ideal laboratory conditions. Therefore,

these standard life curves should be used only as a guideline. Comparison of measured tempera-

tures to MICROTEMP® thermal cutoff standard life curves should not replace customer life testing

using functional thermal cutoffs for the particular application. The design engineer must make the

trade-off between response and life of the TCO based on product requirements. It is important to

remember that temperatures experienced in actual application will vary from unit to unit.

Test Procedure

Install the Thermocoupled TCO Test Sample (TTTS) in the electrical circuit to be opened in the

event of a fault condition. Position it in the area that has been selected to be protected within the

product based on prior determinations of the maximum permissible temperatures to be allowed.

The TTTS should be installed using the same mounting and electrical connection that will be

used for functional TCOs in production. Connect the thermocouple leads to a digital

temperature measuring device to record temperatures. The product to be protected can now

be operated, and the normal operating temperature monitored. Note that the TTTS is not a

functional TCO and therefore will not open the circuit in the test setup.

THERMAL CUTOFF "DUMMY"

TERMINAL OR SPLICE

ELECTRICAL INSULATOR

CONNECTNG CONDUIT WIRE

THERMOCOUPLE

TEMPERATURE OR VOLTAGE MEASURING DEVICE

Figure 6

Figure 6 illustrates a typical installation of a TTTS. Note that the body of the TTTS is at the same

potential as the connecting circuit; therefore, it must be electrically isolated from the surface

against which the cutoff is mounted. Also note that the thermocouple wire is at the same poten-

tial as the connecting circuit.

CAUTION . . . To avoid a false reading of the unit under test, thermocouple wires must not make

contact with each other except at the temperature sensing junction.

CAUTION . . . Ensure that the thermocouple wire insulation will provide isolation against short-

circuiting and shock hazards.

CAUTION . . . The terminal of the temperature measuring instrument, to which the thermocouple

is attached, will be at the same potential as the connecting circuit wire. This instrument must

be electrically isolated and considerable caution must be exercised in its use, since one of the

thermocouple terminals is frequently grounded to the instrument chassis.

Before using measuring equipment powered directly from standard line voltages, check operation

manuals. Be sure line voltages impressed on the thermocouple wires by the TTTS will not cause

damage to the instrument.

The more closely the actual operating and ambient conditions can be simulated during test, the

more valid the test results will be. These tests are necessary to empirically include the variable

factors that need to be considered to select the properly rated thermal cutoffs. These factors

include, but are not limited to, the heating effect of the current through the cutoff, adjoining

terminals and leads, heating or cooling effect of the terminals and external leads, rate of

temperature rise, air flow, shock, vibration and other environmental and operating conditions

unique to the application.

The product and application being tested will determine the number of cycles that must be run to

determine the maximum “normal” operating temperature. “Overshoot” temperatures should be

included in the determination of the maximum “normal” operating temperature. The overshoot

temperature is often considerably higher than the temperature reached at the moment the

thermostat opens. The conclusion of these tests will provide the maximum “normal” operating

temperature at the thermal cutoff (at maximum anticipated voltage, ambient temperature, etc).

The overshoot temperature seen by the thermal cutoff after the thermal cutoff opens in the

application must also be carefully examined and compared to Tmax.

Manufacturing tolerances and variations should be carefully considered, and a sufficient number

of units evaluated, to provide a statistical basis on which to determine the operating overshoot

temperatures.

After obtaining the above information, test the product under fault conditions and monitor to

determine that desired fault condition temperatures are not exceeded.

Where there are a variety of fault conditions, (e.g., short-circuited thermostats and transformer

secondaries, locked motor rotors and solenoids, high ambient temperatures, restricted or

blocked airflow, etc.), consideration should be given to multiple fault conditions which could

occur simultaneously during the lifetime of the product, and to faults which may cause localized

overheating in areas away from the TCO.

When the fault conditions have been set up, note the temperature of the TTTS when the

maximum desired temperature limit is reached. At this point the circuit is manually interrupted.

This test should be run several times, in several different units. In some applications, it will not

be possible to “save” the tested item from damage, but only prevent the product from creating

an external fire or electrical hazard. Damaged products should not be retested, since the results

may not be the same as with undamaged units. The MICROTEMP® thermal cutoff ratings selected

should be equal to or less than the temperature recorded at the TTTS at the time the maximum

desired temperature is reached.

CAUTION . . . Excessive overshoot temperatures after the opening of the thermal cutoff may cause

dielectric breakdown of the thermal cutoff and allow reconduction to occur. Functional thermal

cutoffs should be tested to verify proper operation of the thermal cutoffs in the application (see

Microtemp® TCO Operating Temperature Summary and Electrical Rating Summary on page 4).

Substitute actual thermal cutoffs in a sufficient number of finished products and re-run the

tests to obtain statistical verification of the results. For multiple TCO applications, test functional

thermal cutoffs under fault conditions so that the product overheats and each thermal cutoff is

independently called upon to interrupt the flow of current. Each thermal cutoff should open the

circuit independently of any other over-temperature limit controls, with product damage not

exceeding an acceptable level. This test should be run using the maximum voltage and current;

the thermal cutoff will be expected to interrupt and hold open.

Installation of Thermal Cutoffs

The performance of a MICROTEMP® thermal cutoff can be affected by installation methods such

as soldering, welding, splicing, lead bending, insulation, clamping and mounting. Certain precautions

should be taken during installation to ensure that the MICROTEMP® thermal cutoff is not damaged,

which may cause it to not operate in its intended manner. Likewise, care should be taken during

installation to ensure that the TCO in every unit experiences the expected temperature range

environment previously determined during the calibration temperature selection. The

following guidelines should be used to minimize undesirable conditions that can result from

improper installation practices.

Soldering Leads

Thermal cutoff leads should be heat sinked during the soldering operation (see figure 7). If

excessive heat is conducted by the leads into the thermal cutoff, it can shorten the life of the TCO.

In addition, excessive lead temperatures can damage the epoxy and possibly result in the TCO

failing to open. More heat sinking is necessary for thermal cutoffs with low temperature ratings.

HEAT SINK HERE

SOLDER SOLDER

Figure 7

Test samples should be x-rayed before and after the soldering operation. The size of the chemical

pellet should be measured with an optical comparator or a toolmaker’s microscope to verify that

no shrinkage has occurred during the soldering operation (see figure 8). The epoxy seal should

retain its size and shape and not discolor. If the chemical pellet or the epoxy have changed size as

a result of the soldering operation more heat sinking is required.

EPOXY SEAL BARREL

SPRING

THERMAL PELLET

ISOLATED

LEAD

TRIP

SPRING

CASE &

LEAD ASSEMBLY

Figure 8

Welding Leads

The thermal cutoff leads may also need to be heat sinked during a welding operation (see figure

9). The same precautions and tests described in the soldering section should also be followed for

welded leads.

WELD POINTS

HEAT SINK HERE

Figure 9

To avoid damaging or welding internal parts, care should be taken that none of the welding current

is conducted through the TCO. A welding current of hundreds of amperes can weld the internal

parts together, resulting in the TCO failing to open.

TCO leads must be supported during the weld operation to prevent breaking the thermal cutoff

epoxy seal.

Splices & Terminals

Insecure splices and terminations may produce high resistance junctions which can cause self

heating (I2R) as power is dissipated across these junctions during product operation.

Heat from these hot spots can flow down the thermal cutoff leads and increase the temperature

of the thermal cutoff (see figure 10). Nuisance openings of the thermal cutoffs or degradation of

the epoxy seal can occur as a result of the heat generated by high resistance junctions. The splice

or termination junction may initially measure low resistance, but can change to a much higher

resistance after several temperature cycles. It is generally better to splice MICROTEMP® thermal

cutoff leads to stranded lead wires rather than solid wires as the stranded wire may be crimped

tighter and maintain better electrical contact during temperature cycling.

SPLICE HEAT FLOW HEAT FLOW

NUT

LOCK

WASHER

BOLT

SPLICE

TERMINATION

SPLICE

Figure 10

The temperature capabilities of the splice and/or termination should be considered. For example,

solder back-up should be considered for splices of terminations in applications cycled at temperatures

exceeding 150°C.

Bending Leads

When configuring leads, special care must be exercised in supporting the leads at each end near

the body of the thermal cutoff so that the case will not be distorted or the epoxy will not be

cracked or broken. At least 0.125” (3mm) should be maintained between the epoxy seal and any

lead bends (see figure 11).

.09 MIN.

(2.3 mm)

.04 MIN. RAD.

(

1.0 mm

)

.70 MIN. (17.8 mm)

Figure 11

Dimensions are shown in inches (millimeters).

Thermal Gradients

Ideal TCO placement subjects the entire TCO case, leads, epoxy seal and internal components to a

uniform temperature environment.

Care should be exercised in the placement of the TCO to minimize thermal gradients across the

TCO body. In certain applications, the TCO can be mounted in a position where heat is conducted

to the body of the TCO through one of the leads, resulting in thermal gradients across the TCO.

Over time, the TCO life can be reduced by thermal gradients if the isolated (epoxy) lead is at a

consistently lower temperature than the case lead. Long term testing is recommended in

determining whether these conditions exist in the application.

To minimize the effects of thermal gradients and the temperature increase of the TCO body from

this heat flow, attach the isolated (epoxy) lead, rather than the case lead, to the heat source.

TTTS can be supplied with thermocouples on both ends to facilitate gradient evaluations.

Temperature Limits

The temperatures experienced during normal operation, including expected temperature over-

shoots, will determine the life expectancy of the TCO. Nuisance trips can result if the thermal cut-

off rating is too close to the temperatures experienced during normal operation. Thermal cutoffs

of any temperature rating should not be subjected to continuous normal temperatures in excess

of 200°C. Additionally, overshoot temperatures after the opening of the thermal cutoff should be

minimized to avoid dielectric breakdown and reconduction of the thermal cutoff.

CAUTION . . . The thermal cutoff may fail to open the electrical circuit under certain conditions.

Distortion of the case, breaking or cracking the seal, exposing the epoxy seal to cleaning solvents,

compression of the leads and current surges that exceed the operating specifications of the thermal

cutoff may cause the thermal cutoff not to open. In addition, pellet shrinkage due to thermal

aging under some circumstances may also result in failure to open. Finally, a very low rate of

temperature rise may produce conditions that may also result in failure to open. Care must be

taken to avoid any mishandling or misapplication of the thermal cutoff.

CAUTION . . . Although TCOs are highly reliable devices, a TCO may fail to open in operation for

one or more of the reasons set forth above. These conditions must be taken into account by the

product design engineer in determining the level of reliability needed for the application. If failure

of the TCO to open could result in personal injury or property damage, the product design engineer

may want to consider using one or more redundant TCOs of different ratings to achieve the

desired level of reliability. A number of consumer product design engineers have incorporated

redundant TCOs of different ratings in their designs for this reason.

Definition of Terms

Maximum Open Temperature or Rated Functioning Temperature (Tf, TF):

The maximum temperature at which the thermal cutoff changes its state of conductivity to open

circuit with detection current as the only load. The rated functioning temperature is measured

during a temperature rise of approximately 0.5°C per minute.

Holding Temperature (Th, TH):

Maximum temperature of the MICROTEMP® TCO measured at the case end of the thermal cutoff at

which the thermal cutoff can be maintained for a period for 168 hours without opening. NOTE: it is

advised that TCOs are not exposed to continuous operating temperatures in excess of Tf -25°C.

Maximum Overshoot Temperature or Maximum Temperature Limit (Tm, TM):

The maximum temperature at which the thermal cutoff, having changed its state of conductivity,

can be maintained at twice rated voltage for a specified period of time, during which its

mechanical and electrical properties will not be impaired.

Rated Voltage:

The maximum voltage that can be applied to the circuit in which the thermal cutoff is used.

Rated Current:

The maximum current that the thermal cutoff is rated to interrupt at the rated voltage.

Agency Recognition

MICROTEMP® thermal cutoffs are recognized by the following major agencies:

UL BEAB METI CSA CCC VDE

Underwriters British Ministry of Canadian China Varband

Laboratories Inc. Electrotechnical Economy, Trade Standards Cumpulsary Deutscher

(USA) Approvals Board and Industry of Association Product Electrotechniker e.V.

Japan Certification (F. R. G.)

MICROTEMP® thermal cutoffs are recognized by the major approval agencies throughout the world

for AC circuit applications. These agency electrical ratings can be used as a guideline when evalu-

ating specific thermal cutoff applications. However, the electrical and thermal conditions to which

the thermal cutoff may be exposed in an application may differ significantly from agency test con-

ditions. Accordingly, customers should not rely solely on agency ratings but rather must perform

adequate testing on the particular application to confirm that the TCO selected is appropriate for

that application and will operate as intended.

Important Notice

Users must determine the suitability of the control for their application, including the level of

reliability required, and are solely responsible for the function of the end-use product.

These controls contain exposed electrical components and are not intended to withstand

exposure to water or other environmental contaminants which can compromise insulating

components. Such exposure may result in insulation breakdown and accompanying localized

electrical heating.

A control may remain permanently closed or open as a result of exposure to excessive mechanical,

electrical, thermal or environmental conditions or at normal end-of-life. If failure of the control to

operate could result in personal injury or property damage, the user should incorporate supplemental

system control features to achieve the desired level of reliability and safety. For example, backup

controls have been incorporated in a number of applications for this reason.