24V DRIVE INTERFACE BOARD FTP-621DCL002/012 FOR FTP-621/631/641MCL101/102/301/302 INTERFACE 1. Centronics standard (1) Connector (CN10) Connector part number : FCN-605Q030-G/M (Fujitsu Components) or equivalent Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET -- Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET -- Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET -- Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET -- Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET -- Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET -- Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET -- Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET -- Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET -- Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET -- Connected to logic GND 21 BUSY O Busy 22 BUSY-RET -- Connected to logic GND 23 RINF2 O Printer status 24 INPRM-RET -- Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 28 RINF3 O Printer status 29 ATF I Paper feed request 30 GND -- Logic GND Notes: * Symbol "----" means a negative logic signal. * "-RET" signal is a return signal of the twisted pair cable. * "I" or "O" means a signal direction from the interface board side. 1 FTP-621DCL002/012 (3) Connector pin number (4) Data input signal timing FCN-605Q030-G/M (Fujitsu Components) or equivalent PRDT07 t1 t3 PRSTB t2 No.1 BUSY t4 No.30 No.2 ACKNLG t5 Data set time : t10.5 sec PRSTB pulse : t20.5 sec Data hold time : t30.5 sec PRSTB to BUSY = "H" : t40.5 sec . ACKNLG pulse : t5=5.0 sec . 2 FTP-621DCL002/012 2. Bus interface (1) Connector Connector part number : FCN-215Q040-G/0 (Fujitsu Components) or equivalent Mating connector part number : FCN-217J040-G/0 (Fujitsu Components) or equivalent : FCN-214J040-G/0 (Fujitsu Components)or equivalent : FCN-215J040-G/0 (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 ALE O Address latch 2 BRD -- Data read 3 BWR -- Data write 4 READY -- Data access ready 5 HACK -- Hold acknowledge 6 HRQ -- User hold request input 7 MCRC -- Power-down (not used) 8 CLK O System clock 9 PCPAK1 O Common RAM reading completion 10 ATF I Automatic paper loading 11 PCPSD1 I Common RAM reading request 12 PRON O Printer operating 13 RST I Hard reset 14 GND -- Ground 15 DB00 I/O External address/Data bus 0 16 DB01 I/O External address/Data bus 1 17 DB02 I/O External address/Data bus 2 18 DB03 I/O External address/Data bus 3 19 DB04 I/O External address/Data bus 4 20 DB05 I/O External address/Data bus 5 21 DB06 I/O External address/Data bus 6 22 DB07 I/O External address/Data bus 7 23 AB08 O External address bus 08 24 AB09 O External address bus 09 25 AB10 O External address bus 10 26 AB11 O External address bus 11 27 AB12 O External address bus 12 28 AB13 O External address bus 13 29 AB14 O External address bus 14 30 AB15 O External address bus 15 31 AB16 O External address bus 16 32 AB17 O External address bus 17 33 AB18 O External address bus 18 34 AB19 O External address bus 19 35 AB20 O External address bus 20 36 AB21 O External address bus 21 37 AB22 O External address bus 22 38 AB23 O External address bus 23 39 RAM2 O Common RAM access 40 INPRM I Reset Notes: * Symbol "----" means a negative logic signal. * "I" or "O" means a signal direction from the interface board side. 3 FTP-621DCL002/012 CONNECTOR PIN ASSIGNMENT 1. Connector for logic power supply (CN1) Part number : B4B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-4 (J.S.T) or equivalent Cable side No. Signal I/O Contents No. Signal I/O Contents 1 VCC -- Power supply for logic (+5V) 2 GND -- Logic ground 3 GND -- Logic ground 4 VDD -- Power supply for head/motor (+24V) 2. Connector for thermal head and motor power supply (CN2) Part number : B8B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-8 (J.S.T) or equivalent Cable side No. Signal I/O Contents No. Signal I/O Contents 1 VDD -- Power supply for head/motor (+24V) 2 VDD -- Power supply for head/motor (+24V) 3 VDD -- Power supply for head/motor (+24V) 4 VDD -- Power supply for head/motor (+24V) 5 GND -- Head/motor ground 6 GND -- Head/motor ground 7 GND -- Head/motor ground 8 GND -- Head/motor ground 4 FTP-621DCL002/012 3. Connector for thermal head drive (CN9) Part number : FCN-605Q026-G/M (Fujitsu Components) or equivalent P.C.B side Mating connector part number : FCN-747B026-AU/B (Fujitsu Components) or equivalent Cable side No. Signal I/O Contents No. Signal I/O Contents 1 VDD -- Power for head (+24V) 2 GND -- Head ground 3 VDD -- Power for head (+24V) 4 GND -- Head ground 5 VDD -- Power for head (+24V) 6 GND -- Head ground 7 LAT O Printing data latch 8 HD O Printing data output 9 ENB5 * O Printing enable 5 (not used) 10 ENB4 * O Printing enable 4 (not used) 11 ENB3 * O Printing enable 3 (not used) 12 ENB2 O Printing enable 2 13 ENB1 O Printing enable 1 14 ENB0 O Printing enable 0 15 VREF O Power for thermistor 16 TMP I Temperature detection 17 B.E.O -- Head current control 18 VCC -- 19 HCLK O Data transmission clock 20 HSEN I 21 VDD -- Power for head (+24V) 22 GND -- Head ground 23 VDD -- Power for head (+24V) 24 GND -- Head ground 25 VDD -- Power for head (+24V) 26 GND -- Head ground Power for logic (+5V) Printer distinction Notes: * Symbol "----" means a negative logic signal. * "I" or "O" means a signal direction from the interface board side. *: Not used at mechanism side. 4. Connector for Head-up/paper-out detection (CN4) Part number : B5B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-5 (J.S.T) or equivalent Cable side No. Signal I/O Contents No. Signal I/O Contents 1 VCC -- Power supply for logic (+5V) 2 PES -- Paper-out detection 3 GND -- Logic ground 4 VCC -- Power supply for logic (+5V) 5 HUP -- Head-up detection 5 FTP-621DCL002/012 5. Connector for paper near end detection (CN3) Part number : B2B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-2 (J.S.T) or equivalent Cable side No. 1 Signal VCC I/O -- Contents Power supply for logic (+5V) No. 2 Signal I/O NES I Contents Paper near end detection Note: The paper near end sensor to be set at the host system side. 6. Connector for stepping motor drive (CN5) Part number : B6B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-6 (J.S.T) or equivalent Cable side No. Signal I/O Contents No. Signal I/O Contents 1 N.C. -- Not connected 2 N.C. -- Not connected 3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation 5 MT/B O Stepping motor coil excitation 6 MT/B O Stepping motor coil excitation 7. Connector for abnormal head temperature detection (CN7) Part number : B3B-XH-A-WHITE (J.S.T) or equivalent P.C.B side Mating connector part number : XHP-3 (J.S.T) or equivalent Cable side No. Signal I/O Contents No. 1 TMPER O Abnormal head temperature detection 2 3 GND -- Logic ground Signal N.C. I/O -- Contents Not connected Note: This signal detects abnormal head temperature. 8. Connector for cutter drive (CN6)*1 Part number: B4B-EH (J.S.T) or equivalent P.C.B side No. Signal I/O Contents No. Signal I/O Contents 1 SW1 I Cutter position detection 2 GND -- Logic ground 3 M+ O Motor drive (+) 4 M- O Motor drive (-) *1 Only for FTP-621DCL012 6 FTP-621DCL002/012 PRINTING COMMANDS (CENTRONICS STANDARD INTERFACE) Name Command Contents Line feed LF Prints buffer data and returns the line to left end of next line. Form feed FF Prints buffer data and returns the line to left end of next form. Carriage return CR Prints buffer data and returns the line to left end of next line. Double width print set SO Sets the double width character. Double width print reset SI Resets the double width character. Black-white negative print set RS Sets the black-white negative printing. Black-white negative print reset US Resets the black-white negative printing. ESC sequence set ESC Indicates the start of an escape sequence formed by this code plus subsequent commands. Double width print set ESC SO Sets the double width character. Double width print reset ESC SI Resets the double width character. Page length set in character line ESC C + n Sets the page length by character line. Reverse print set ESC R Sets reverse printing. Reverse print reset ESC S Resets reverse printing. Bit image print set* ESC V +n1+n2+d1~dN Sets bit image printing. Double width print set and reset ESC W + n Sets and resets the double width character. Printing speed set ESC s + n Sets the printing speed. Line feed length set in n/203 in. ESC 3 + n Sets the line feed length in n/203 in. Character set 2 select ESC 6 Selects the character set 2. Character set 1 select ESC 7 Selects the character set 1. Download character register ESC &+s+n+m+a+d1~dN Registers the download characters. Registered download character select ESC %+n+m Selects the registered download characters. Character set copy ESC :+0+n+m Copies the character set. Bit image print set in high speed ESC +a+n1+n2+d1~dN Sets the bit image printing in high speed. International character set ESC ^+n Selects the international characters. Printer reset ESC @ Initializes the printer. Line feed length set after mark detection ESC w+n Sets the line feed length after mark detection. Mark detection Feeds the paper to the marking position. ESC FF (Continued) 7 FTP-621DCL002/012 (Continued) Name Command Contents Paper feed set in normal direction ESC J+n Sets the paper feed in normal direction. (Feeding range: 1 to 255 dot lines) Paper feed set in reverse direction ESC j+n Sets the paper feed in reverse direction. (Feeding range: 1 to 255 dot lines) Left-end print position set ESC l+n Sets the left end of printing position. Right-end print position set ESC Q+n Sets the left end of printing position. FS sequence set FS Indicates the start of an FS sequence formed by this code plus subsequent commands. 4 times enlarged character set and reset FS W + n Sets and resets the 4 times enlarged characters. Double height print set and reset FS ! +n Sets and resets the double height character. Detecting function set FS 9+n Sets the detecting functions. TOF mark detection FS FF Feeds the paper to the TOF mark position. Printing quality set FS x+n Sets the printing quality conforming to the selected paper. Cutting*1 ESC c+n Executes paper cutting. Cutting type select*1 ESC y+n Selects the cutting type: full, partial, etc. *1 Only for FTP-621DCL012 8 FTP-621DCL002/012 OPTIONS 1. Cable Name Part number Thermal head connection cable Cable length FTP-441Y001 150 mm For Centronics FTP-441Y201 500 mm For Bus I/F FTP-621Y203 500 mm Power supply cable (A): for logic motor FTP-441Y401 300 mm Power supply cable (B): for thermal head FTP-441Y601 300 mm Head abnormal temperature detection cable FTP-621Y204 300 mm Paper near-end detection cable FTP-621Y401 300 mm Interface cable 2. Paper holder Name Part number Flange FTP-040HF Stand FTP-040HS Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info.marketing@fceu.fujitsu.com Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 375-8560 Fax: (65) 273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com (c) 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 09/2001 9