FTP-631MCL102 - Fujitsu - Datasheet.Live

24V DRIVE INTERFACE BOARD

FTP-621DCL002/012

1. Centronics standard

(1) Connector (CN10)

Connector part number : FCN-605Q030-G/M (Fujitsu Components) or equivalent

Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent

No. Signal I/O Contents No. Signal I/O Contents

1 PRSTB I

Data strobe

2 PRSTB-RET —

Connected to logic GND

3 PRDT0 I Data 0 4 PRDT0-RET —

Connected to logic GND

5 PRDT1 I Data 1 6 PRDT1-RET —

Connected to logic GND

7 PRDT2 I Data 2 8 PRDT2-RET —

Connected to logic GND

9 PRDT3 I Data 3 10 PRDT3-RET —

Connected to logic GND

11 PRDT4 I Data 4 12 PRDT4-RET —

Connected to logic GND

13 PRDT5 I Data 5 14 PRDT5-RET —

Connected to logic GND

15 PRDT6 I Data 6 16 PRDT6-RET —

Connected to logic GND

17 PRDT7 I Data 7 18 PRDT7-RET —

Connected to logic GND

19 ACKNLG O Data input acknowledge 20 ACKNLG-RET —

Connected to logic GND

21 BUSY O Busy 22 BUSY-RET —

Connected to logic GND

23 RINF2 O

Printer status

24 INPRM-RET —

Connected to logic GND

25 SLCTIN I Printer select 26 INPRM I Reset

27 RINF1 O

Printer status

28 RINF3 O

Printer status

29 ATF I Paper feed request 30 GND — Logic GND

(2) Connector pin assignment

Notes:

• Symbol “——” means a negative logic signal.

• “–RET” signal is a return signal of the twisted pair cable.

• “I” or “O” means a signal direction from the interface board side.

■INTERFACE

FOR FTP-621/631/641MCL101/102/301/302

FTP-621DCL002/012

FCN-605Q030-G/M (Fujitsu Components) or

equivalent

(3) Connector pin number (4) Data input signal timing

No.1

No.2No.30

PRDT0∼7

PRSTB

BUSY

ACKNLG

t1 t3

Data set time

PRSTB pulse

Data hold time

PRSTB to BUSY = “H”

ACKNLG pulse

: t1≥0.5 µsec

: t2≥0.5 µsec

: t3≥0.5 µsec

: t4≤0.5 µsec

: t5=5.0 µsec

FTP-621DCL002/012

No. Signal I/O Contents No. Signal I/O Contents

1 ALE O Address latch 2 BRD — Data read

3 BWR — Data write 4 READY — Data access ready

5 HACK — Hold acknowledge 6 HRQ — User hold request input

7 MCRC — Power-down (not used) 8 CLK O System clock

9 PCPAK1 O

Common RAM reading completion

10 ATF I Automatic paper loading

11 PCPSD1 I Common RAM reading request 12 PRON O Printer operating

13 RST I Hard reset 14 GND — Ground

15 DB00 I/O External address/Data bus 0 16 DB01 I/O External address/Data bus 1

17 DB02 I/O External address/Data bus 2 18 DB03 I/O External address/Data bus 3

19 DB04 I/O External address/Data bus 4 20 DB05 I/O External address/Data bus 5

21 DB06 I/O External address/Data bus 6 22 DB07 I/O External address/Data bus 7

23 AB08 O External address bus 08 24 AB09 O External address bus 09

25 AB10 O External address bus 10 26 AB11 O External address bus 11

27 AB12 O External address bus 12 28 AB13 O External address bus 13

29 AB14 O External address bus 14 30 AB15 O External address bus 15

31 AB16 O External address bus 16 32 AB17 O External address bus 17

33 AB18 O External address bus 18 34 AB19 O External address bus 19

35 AB20 O External address bus 20 36 AB21 O External address bus 21

37 AB22 O External address bus 22 38 AB23 O External address bus 23

39 RAM2 O Common RAM access 40 INPRM I Reset

2. Bus interface

(1) Connector

Connector part number : FCN-215Q040-G/0 (Fujitsu Components) or equivalent

Mating connector part number : FCN-217J040-G/0 (Fujitsu Components) or equivalent

: FCN-214J040-G/0 (Fujitsu Components)or equivalent

: FCN-215J040-G/0 (Fujitsu Components) or equivalent

(2) Connector pin assignment

Notes:

• Symbol “——” means a negative logic signal.

• “I” or “O” means a signal direction from the interface board side.

FTP-621DCL002/012

■CONNECTOR PIN ASSIGNMENT

1. Connector for logic power supply (CN1)

Part number : B4B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-4 (J.S.T) or equivalent → Cable side

No. Signal I/O Contents No. Signal I/O Contents

1VCC — Power supply for logic (+5V) 2 GND — Logic ground

3 GND — Logic ground 4 VDD — Power supply for head/motor (+24V)

2. Connector for thermal head and motor power supply (CN2)

Part number : B8B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-8 (J.S.T) or equivalent → Cable side

No. Signal I/O Contents No. Signal I/O Contents

1VDD —

Power supply for head/motor (+24V)

2VDD — Power supply for head/motor (+24V)

3VDD —

Power supply for head/motor (+24V)

4VDD — Power supply for head/motor (+24V)

5 GND — Head/motor ground 6 GND — Head/motor ground

7 GND — Head/motor ground 8 GND — Head/motor ground

FTP-621DCL002/012

3. Connector for thermal head drive (CN9)

Part number : FCN-605Q026-G/M (Fujitsu Components) or equivalent → P.C.B side

Mating connector part number : FCN-747B026-AU/B (Fujitsu Components) or equivalent → Cable side

No. Signal I/O Contents No. Signal I/O Contents

1VDD — Power for head (+24V) 2 GND — Head ground

3VDD — Power for head (+24V) 4 GND — Head ground

5VDD — Power for head (+24V) 6 GND — Head ground

7 LAT O Printing data latch 8 HD O Printing data output

9 ENB5 * O Printing enable 5 (not used) 10 ENB4 * O Printing enable 4 (not used)

11 ENB3 * O Printing enable 3 (not used) 12 ENB2 O Printing enable 2

13 ENB1 O Printing enable 1 14 ENB0 O Printing enable 0

15 VREF O Power for thermistor 16 TMP I Temperature detection

17 B.E.O — Head current control 18 VCC — Power for logic (+5V)

19 HCLK O Data transmission clock 20 HSEN I Printer distinction

21 VDD — Power for head (+24V) 22 GND — Head ground

23 VDD — Power for head (+24V) 24 GND — Head ground

25 VDD — Power for head (+24V) 26 GND — Head ground

Notes:

• Symbol “——” means a negative logic signal.

• “I” or “O” means a signal direction from the interface board side.

*: Not used at mechanism side.

4. Connector for Head-up/paper-out detection (CN4)

Part number : B5B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-5 (J.S.T) or equivalent → Cable side

No. Signal I/O Contents No. Signal I/O Contents

1VCC — Power supply for logic (+5V) 2 PES — Paper-out detection

3 GND — Logic ground 4 VCC — Power supply for logic (+5V)

5 HUP — Head-up detection

FTP-621DCL002/012

No. Signal I/O Contents No. Signal I/O Contents

1 N.C. — Not connected 2 N.C. — Not connected

3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation

5 MT/B O Stepping motor coil excitation 6 MT/B O Stepping motor coil excitation

No. Signal I/O Contents No. Signal I/O Contents

1VCC — Power supply for logic (+5V) 2 NES I Paper near end detection

6. Connector for stepping motor drive (CN5)

Part number : B6B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-6 (J.S.T) or equivalent → Cable side

5. Connector for paper near end detection (CN3)

Part number : B2B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-2 (J.S.T) or equivalent → Cable side

Note: The paper near end sensor to be set at the host system side.

7. Connector for abnormal head temperature detection (CN7)

Part number : B3B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side

Mating connector part number : XHP-3 (J.S.T) or equivalent → Cable side

Note: This signal detects abnormal head temperature.

8. Connector for cutter drive (CN6)*1

Part number: B4B-EH (J.S.T) or equivalent → P.C.B side

No. Signal I/O Contents No. Signal I/O Contents

1 SW1 I Cutter position detection 2 GND — Logic ground

3 M+ O Motor drive (+) 4 M– O Motor drive (–)

No. Signal I/O Contents No. Signal I/O Contents

1 TMPER O

Abnormal head temperature detection

2 N.C. — Not connected

3 GND — Logic ground

*1 Only for FTP-621DCL012

FTP-621DCL002/012

Name Command Contents

Line feed LF Prints buffer data and returns the line to left end of

next line.

Form feed FF Prints buffer data and returns the line to left end of

next form.

Carriage return CR Prints buffer data and returns the line to left end of

next line.

Double width print set SO Sets the double width character.

Double width print reset SI Resets the double width character.

Black-white negative print set RS Sets the black-white negative printing.

Black-white negative print reset US Resets the black-white negative printing.

ESC sequence set ESC Indicates the start of an escape sequence formed

by this code plus subsequent commands.

Double width print set ESC SO Sets the double width character.

Double width print reset ESC SI Resets the double width character.

Page length set in character line ESC C + n Sets the page length by character line.

Reverse print set ESC R Sets reverse printing.

Reverse print reset ESC S Resets reverse printing.

Bit image print set* ESC V +n1+n2+d1~dNSets bit image printing.

Double width print set and reset ESC W + n Sets and resets the double width character.

Printing speed set ESC s + n Sets the printing speed.

Line feed length set in n/203 in. ESC 3 + n Sets the line feed length in n/203 in.

Character set 2 select ESC 6 Selects the character set 2.

Character set 1 select ESC 7 Selects the character set 1.

Download character register ESC &+s+n+m+a+d1~dNRegisters the download characters.

Registered download character select ESC %+n+m Selects the registered download characters.

Character set copy ESC :+0+n+m Copies the character set.

Bit image print set in high speed ESC +a+n1+n2+d1~dNSets the bit image printing in high speed.

International character set ESC ^+n Selects the international characters.

Printer reset ESC @ Initializes the printer.

Line feed length set after mark detection ESC w+n Sets the line feed length after mark detection.

Mark detection ESC FF Feeds the paper to the marking position.

■PRINTING COMMANDS (CENTRONICS STANDARD INTERFACE)

(Continued)

FTP-621DCL002/012

Name Command Contents

Paper feed set in normal direction ESC J+n Sets the paper feed in normal direction.

(Feeding range: 1 to 255 dot lines)

Paper feed set in reverse direction ESC j+n Sets the paper feed in reverse direction.

(Feeding range: 1 to 255 dot lines)

Left-end print position set ESC l+n Sets the left end of printing position.

Right-end print position set ESC Q+n Sets the left end of printing position.

FS sequence set FS Indicates the start of an FS sequence formed by

this code plus subsequent commands.

4 times enlarged character set and reset FS W + n Sets and resets the 4 times enlarged characters.

Double height print set and reset FS ! +n Sets and resets the double height character.

Detecting function set FS 9+n Sets the detecting functions.

TOF mark detection FS FF Feeds the paper to the TOF mark position.

Printing quality set FS x+n Sets the printing quality conforming to the

selected paper.

Cutting*1ESC c+n Executes paper cutting.

Cutting type select*1ESC y+n Selects the cutting type: full, partial, etc.

(Continued)

*1 Only for FTP-621DCL012

FTP-621DCL002/012

■OPTIONS

Name Part number Cable length

Thermal head connection cable FTP-441Y001 150 mm

For Centronics FTP-441Y201 500 mm

Interface cable For Bus I/F FTP-621Y203 500 mm

Power supply cable (A): for logic motor FTP-441Y401 300 mm

Power supply cable (B): for thermal head FTP-441Y601 300 mm

Head abnormal temperature detection cable FTP-621Y204 300 mm

Paper near-end detection cable FTP-621Y401 300 mm

Name Part number

Flange FTP-040HF

Stand FTP-040HS

1. Cable

2. Paper holder

trademarks of their respective owners. Rev. 09/2001

Japan

Fujitsu Component Limited

Gotanda-Chuo Building

3-5, Higashigotanda 2-chome, Shinagawa-ku

Tokyo 141, Japan

Tel: (81-3) 5449-7010

Fax: (81-3) 5449-2626

Email: promothq@ft.ed.fujitsu.com

Web: www.fcl.fujitsu.com

North and South America

Fujitsu Components America, Inc.

250 E. Caribbean Drive

Sunnyvale, CA 94089 U.S.A.

Tel: (1-408) 745-4900

Fax: (1-408) 745-4970

Email: marcom@fcai.fujitsu.com

Web: www.fcai.fujitsu.com

Europe

Fujitsu Components Europe B.V.

Diamantlaan 25

2132 WV Hoofddorp

Netherlands

Tel: (31-23) 5560910

Fax: (31-23) 5560950

Email: info.marketing@fceu.fujitsu.com

Web: www.fceu.fujitsu.com

Asia Pacific

Fujitsu Components Asia Ltd.

102E Pasir Panjang Road

#04-01 Citilink Warehouse Complex

Singapore 118529

Tel: (65) 375-8560

Fax: (65) 273-3021

Email: fcal@fcal.fujitsu.com

www.fcal.fujitsu.com

Fujitsu Components

International

Headquarter

Offices