a High Accuracy anyCAP(R) 100 mA Low Dropout Linear Regulator ADP3307 FEATURES High Accuracy Over Line and Load: 0.8% @ 25C, 1.4% Over Temperature Ultralow Dropout Voltage: 120 mV Typical @ 100 mA Requires only CO = 0.47 F for Stability anyCAP = Stable with All Types of Output Capacitors (Including MLCC) Current and Thermal Limiting Low Noise Dropout Detector Low Shutdown Current: 1 A 3.0 V to 12 V Supply Range -20C to +85C Ambient Temperature Range Several Fixed Voltage Options Ultrasmall SOT-23-6 (RT-6) Package Excellent Line and Load Regulation APPLICATIONS Cellular Telephones Notebook, Palmtop Computers Battery Powered Systems PCMCIA Regulator Bar Code Scanners Camcorders, Cameras FUNCTIONAL BLOCK DIAGRAM ADP3307 Q1 IN R1 THERMAL PROTECTION ERR OUT CC NR Q2 gm DRIVER R2 SD BANDGAP REF GND NR ADP3307-3.3 VIN IN OUT C1 + 0.47F - ERR R1 330k EOUT VOUT = +3.3V C2 0.47F ON OFF SD GND Figure 1. Typical Application Circuit GENERAL DESCRIPTION The ADP3307 is a member of the ADP330x family of precision low dropout anyCAP voltage regulators. The ADP3307 stands out from the conventional LDOs with a novel architecture and an enhanced process. Its patented design requires only a 0.47 F output capacitor for stability. This device is stable with any type of capacitor regardless of its ESR (Equivalent Series Resistance) value, including ceramic types (MLCC) for space restricted applications. The ADP3307 achieves exceptional accuracy of 0.8% at room temperature and 1.4% overall accuracy over temperature, line and load variations. The dropout voltage of the ADP3307 is only 120 mV (typical) at 100 mA. lose regulation or when the short circuit or thermal overload protection is activated. Other features include shutdown and optional noise reduction capabilities. The ADP330x anyCAP LDO family offers a wide range of output voltages and output current levels from 50 mA to 300 mA: ADP3300 (50 mA, SOT-23-6) ADP3307 (100 mA, SOT-23-6) ADP3301 (100 mA, R-8) ADP3302 (100 mA, Dual Output) ADP3303 (200 mA) The ADP3307 operates with a wide input voltage range from 3.0 V to 12 V and delivers a load current in excess of 100 mA. It features an error flag that signals when the device is about to anyCAP is a registered trademark of Analog Devices, Inc. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2001 (@ T = -20C to +85C, V ADP3307-SPECIFICATIONS otherwise noted) The following specifications apply to all voltage options. A IN 1 = 7 V, CIN = 0.47 F, COUT = 0.47 F, unless Parameter Symbol Conditions Min OUTPUT VOLTAGE ACCURACY VOUT VIN = VOUTNOM + 0.3 V to 12 V IL = 0.1 mA to 100 mA TA = 25C VIN = VOUTNOM + 0.3 V to 12 V IL = 0.1 mA to 100 mA Typ Max Unit -0.8 +0.8 % -1.4 +1.4 % V O V IN VIN = VOUTNOM + 0.3 V to 12 V TA = 25C 0.02 mV/V V O I L IL = 0.1 mA to 100 mA TA = 25C 0.06 mV/mA GROUND CURRENT IGND IL = 100 mA IL = 0.1 mA 0.76 0.19 2.0 0.3 mA mA GROUND CURRENT IN DROPOUT IGND VIN = 2.5 V IL = 0.1 mA 0.6 1.2 mA VOUT = 98% of VOUTNOM IL = 100 mA IL = 10 mA IL = 1 mA 0.126 0.025 0.004 0.22 0.07 0.015 V V V 0.75 0.75 0.3 V V 1 22 A A 0.005 1 A 0.01 3 A LINE REGULATION LOAD REGULATION DROPOUT VOLTAGE SHUTDOWN THRESHOLD SHUTDOWN PIN INPUT CURRENT VDROP VTHSD ISDIN GROUND CURRENT IN SHUTDOWN IQ MODE ON OFF 2.0 0 < VSD < 5 V 5 V < VSD 12 V @ VIN = 12 V VSD = 0 V, VIN = 12 V TA = 25C VSD = 0 V, VIN = 12 V TA = 85C OUTPUT CURRENT IN SHUTDOWN MODE IOSD TA = 25C @ VIN = 12 V TA = 85C @ VIN = 12 V 2 4 A A ERROR PIN OUTPUT LEAKAGE IEL VEO = 5 V 13 A ERROR PIN OUTPUT "LOW" VOLTAGE VEOL ISINK = 400 A 0.12 0.3 V PEAK LOAD CURRENT ILDPK VIN = VOUTNOM + 1 V 170 mA OUTPUT NOISE @ 3.3 V OUTPUT VNOISE f = 10 Hz-100 kHz CNR = 0 CNR = 10 nF, CL = 10 F 100 30 V rms V rms NOTES Ambient temperature of 85C corresponds to a junction temperature of 125C under typical full load test conditions. Specifications subject to change without notice. 1 -2- REV. A ADP3307 ABSOLUTE MAXIMUM RATINGS* PIN FUNCTION DESCRIPTIONS Input Supply Voltage . . . . . . . . . . . . . . . . . . . -0.3 V to +16 V Shutdown Input Voltage . . . . . . . . . . . . . . . . -0.3 V to +16 V Error Flag Output Voltage . . . . . . . . . . . . . . . -0.3 V to +16 V Noise Bypass Pin Voltage . . . . . . . . . . . . . . . . -0.3 V to +5 V Power Dissipation . . . . . . . . . . . . . . . . . . . Internally Limited Operating Ambient Temperature Range . . . -55C to +125C Operating Junction Temperature Range . . . -55C to +125C JA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230C/W JC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92C/W Storage Temperature Range . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering 10 sec) . . . . . . . . 300C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 220C *This is a stress rating only; operation beyond these limits can cause the device to be permanently damaged. ORDERING GUIDE Model Output Voltage Package Option Marking Code ADP3307ART-2.7 ADP3307ART-2.85 ADP3307ART-3 ADP3307ART-3.2 ADP3307ART-3.3 2.7 V 2.85 V 3.0 V 3.2 V 3.3 V RT-6 RT-6 RT-6 RT-6 RT-6 LTC LXC LUC LVC LWC Pin Name Function 1 2 GND NR 3 SD 4 OUT 5 6 IN ERR Ground Pin Noise Reduction Pin. Used for further reduction of the output noise. (See text for details.) No connection if not used. Active Low Shutdown Pin. Connect to ground to disable the regulator output. When shutdown is not used, this pin should be connected to the input pin. Output of the Regulator, fixed 2.7 V, 3.0 V, 3.2 V or 3.3 V output voltage. Bypass to ground with a 0.47 F or larger capacitor. Regulator Input Open Collector Output that goes low to indicate that the output is about to go out of regulation. PIN CONFIGURATION 6 ERR GND 1 ADP3307 NR 2 Contact the factory for the availability of other output voltage options. SD 3 TOP VIEW (Not to Scale) 5 IN 4 OUT Other Members of anyCAP Family 1 Model Output Current Package Options2 Comments ADP3300 ADP3301 ADP3302 ADP3303 50 mA 100 mA 100 mA 200 mA SOT-23-6 R-8 R-8 R-8 High Accuracy High Accuracy Dual Output High Accuracy NOTES 1 See individual data sheets for detailed ordering information. 2 R = Small Outline, SOT-23 = Surface Mount, TSSOP = Thin Shrink Small Outline. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP3307 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. A -3- WARNING! ESD SENSITIVE DEVICE ADP3307-Typical Performance Characteristics IL = 0mA VOUT = 3.2V 3.199 IL = 50mA 3.198 3.197 GROUND CURRENT - A OUTPUT VOLTAGE - Volts IL = 10mA 3.200 VOUT = 3.2V IL = 0 VOUT = 3.2V VIN = 7V 3.201 3.201 OUTPUT VOLTAGE - Volts 800 3.202 3.202 3.200 3.199 3.198 3.197 640 480 320 160 3.196 3.196 IL = 100mA 3.195 3.3 5 6 7 8 9 10 11 12 13 14 INPUT VOLTAGE - Volts 0 TPC 1. Line Regulation Output Voltage vs. Supply Voltage 450 IL = 0 TO 100mA 300 1000 IL = 0 0.0 -0.1 IL = 50mA -0.2 IL = 100mA -0.3 0 50 75 25 OUTPUT LOAD - mA 100 TPC 4. Ground Current vs. Load Current -0.4 -45 -25 -5 48 24 25 50 75 OUTPUT LOAD - mA TPC 7. Dropout Voltage vs. Output Current 100 -5 15 35 55 75 95 TEMPERATURE - C 115 135 TPC 6. Quiescent Current vs. Temperature 8.0 VIN VOUT = 3.2V RL = 32 4 3 2 1 0 0 400 0 -25 15 35 55 75 95 115 135 TEMPERATURE - C INPUT/OUTPUT VOLTAGE - Volts INPUT/OUTPUT VOLTAGE - Volts 72 600 200 5 96 800 TPC 5. Output Voltage Variation % vs. Temperature 120 1.2 2.4 3.6 4.8 6.0 7.2 8.4 9.6 10.8 12.0 INPUT VOLTAGE - Volts TPC 3. Quiescent Current vs. Supply Voltage--3.2 V (Both Outputs) GROUND CURRENT - A OUTPUT VOLTAGE - % GROUND CURRENT - A 0 90 100 0.1 600 INPUT/OUTPUT VOLTAGE - mV 30 40 50 60 70 80 OUTPUT LOAD - mA 0.2 750 0 10 20 TPC 2. Output Voltage vs. Load Current Up to 100 mA 900 150 0 3.195 4 0 1 2 3 4 3 2 INPUT VOLTAGE - Volts 1 TPC 8. Power-Up/Power-Down -4- 0 7.0 6.0 5.0 4.0 VOUT 3.0 VSD = VIN CL = 0.47F RL = 32 VOUT = 3.2V 2.0 1.0 0 0 20 40 60 80 100 120 140 160 180 200 TIME - s TPC 9. Power-Up Overshoot REV. A ADP3307 3.220 3.220 3.220 VOUT = 3.2V 3.210 3.200 3.200 3.190 3.190 RL = 32 CL = 0.47F 3.180 VIN 3.180 VIN 7.0 7.0 40 80 120 160 200 240 280 320 360 400 TIME - s TPC 10. Line Transient Response 100 mA 7.5 0 3.200 3.190 RL = 3.2k CL = 0.47F 3.180 7.5 10 20 40 60 0 0 80 100 120 140 160 180 200 TIME - s TPC 11. Line Transient Response 400 500 4 VOUT = 3.2V CL = 4.7F 3.210 CL = 0.47F 300 3.200 mA VOLTS 200 300 TIME - s 100 TPC 12. Load Transient 3.220 200 IOUT 3.2V 2 100 VOLTS 0 3.180 VOLTS 4 mA 100 10 VOUT 3 3.190 VOUT = 3.2V CL = 4.7F 1 VOUT = 3.2V RL = 32 0 3 2 VOUT VSD 0 3V 0 100 200 300 TIME - s 400 0 0.5 500 TPC 13. Load Transient 1 1.5 2 2.5 3 3.5 TIME - sec 0 VOUT = 3.2V RL = 32 -10 CL = 0.47F -20 RIPPLE REJECTION - dB 3 2 1 0 3 VOUT = 3.3V a. 0.47F, RL = 33k b. 0.47F, RL = 33 c. 10F, RL = 33k d. 10F, RL = 33 b -30 -40 -50 d a -60 -70 c b d -80 VSD 0 5 -90 0 10 20 30 TIME - s TPC 16. Turn Off REV. A 40 0 20 50 -100 a c 10 100 1k 10k 100k FREQUENCY - Hz 1M 10M TPC 17. Power Supply Ripple Rejection -5- 40 60 TIME - s 80 100 TPC 15. Turn On TPC 14. Short Circuit Current 4 3.2V 4 4.5 VOLTAGE NOISE SPECTRAL DENSITY - V Hz 0 VOLTS VOUT = 3.2V CL = 0.47F 3.210 VOLTS 3.210 VOLTS VOLTS VOUT = 3.2V 10 0.47F BYPASS PIN 5 TO PIN 1 VOUT = 5V, CL = 0.47F IL = 1mA, CNR = 0 1 VOUT = 3.3V, CL = 0.47F IL = 1mA, CNR = 0 0.1 VOUT = 2.7- 5.0V, CL = 0.47F IL = 1mA, CNR = 10nF 0.01 100 VOUT = 2.7- 5.0V, CL = 4.7F IL = 1mA, CNR = 10nF 1k 10k FREQUENCY - Hz 100k TPC 18. Output Noise Density ADP3307 This is no longer true with the ADP3307 anyCAP LDO. It can be used with virtually any good quality capacitor, with no constraint on the minimum ESR. The innovative design allows the circuit to be stable with just a small 0.47 F capacitor on the output. Additional advantages of the design scheme include superior line noise rejection and very high regulator gain that lead to excellent line and load regulation. An impressive 1.4% accuracy is guaranteed over line, load and temperature. THEORY OF OPERATION The ADP3307 anyCAP LDO uses a single control loop for regulation and reference functions. The output voltage is sensed by a resistive voltage divider consisting of R1 and R2 which is varied to provide the available output voltage option. Feedback is taken from this network by way of a series diode (D1) and a second resistor divider (R3 and R4) to the input of an amplifier. INPUT OUTPUT Additional features of the circuit include current limit, thermal shutdown and noise reduction. Compared to the standard solutions that give warning after the output has lost regulation, the ADP3307 provides improved system performance by enabling the ERR pin to give warning before the device loses regulation. COMPENSATION ATTENUATION R1 CAPACITOR (VBANDGAP/VOUT) Q1 NONINVERTING WIDEBAND DRIVER gm R3 PTAT VOS D1 (a) R4 ADP3307 PTAT CURRENT RLOAD As the chip's temperature rises above 165C, the circuit activates a soft thermal shutdown, indicated by a signal low on the ERR pin, to reduce the current to a safe level. R2 CLOAD To reduce the noise gain of the loop, the node of the main divider network (a) is made available at the noise reduction (NR) pin which can be bypassed with a small capacitor (10 nF-100 nF). GND Figure 2. Functional Block Diagram A very high gain error amplifier is used to control this loop. The amplifier is constructed in such a way that at equilibrium it produces a large, temperature proportional input "offset voltage" that is repeatable and very well controlled. The gained up temperature proportional offset voltage is combined with the diode voltage to form a "virtual bandgap" voltage, implicit in the network, although it never appears explicitly in the circuit. Ultimately, this patented design makes it possible to control the loop with only one amplifier. This technique also improves the noise characteristics of the amplifier by providing more flexibility on the trade-off of noise sources that leads to a low noise design. APPLICATION INFORMATION Capacitor Selection: anyCAP Output Capacitors: as with any micropower device, output transient response is a function of the output capacitance. The ADP3307 is stable with a wide range of capacitor values, types and ESR (anyCAP). A capacitor as low as 0.47 F is all that is needed for stability. However, larger capacitors can be used if high output current surges are anticipated. There is an upper limit on the size of the output capacitor. The ADP3307 is stable with extremely low ESR capacitors (ESR 0), such as multilayer ceramic capacitors (MLCC) or OSCON. The R1, R2 divider is chosen in the same ratio as the bandgap voltage to the output voltage. Although the R1, R2 resistor divider is loaded by the diode D1, and a second divider consisting of R3 and R4, the values are chosen to produce a temperature stable output. Input Bypass Capacitor: an input bypass capacitor is not required; however, for applications where the input source is high impedance or far from the input pins, a bypass capacitor is recommended. Connecting a 0.47 F capacitor from the input to ground reduces the circuit's sensitivity to PC board layout. If a bigger output capacitor is used, the input capacitor should be 1 F minimum. The patented amplifier controls a new and unique noninverting driver that drives the pass transistor, Q1. The use of this special noninverting driver enables the frequency compensation to include the load capacitor in a pole splitting arrangement to achieve reduced sensitivity to the value, type and ESR of the load capacitance. Noise Reduction A noise reduction capacitor (CNR) can be used to further reduce the noise by 6 dB-10 dB (Figure 3). Low leakage capacitors in 10 nF-100 nF range provide the best performance. As the noise reduction capacitor increases the high frequency loop-gain of the regulator, the circuit requires a larger output capacitor if it is used. The recommended value is 4.7 F, as shown in Figure 3. Since the noise reduction pin (NR) is internally connected to a high impedance node, any connection to this node should be carefully done to avoid noise pick up from external sources. The pad connected to this pin should be as small as possible. Long PC board traces are not recommended. Most LDOs place strict requirements on the range of ESR values for the output capacitor because they are difficult to stabilize due to the uncertainty of load capacitance and resistance. Moreover, the ESR value, required to keep conventional LDOs stable, changes depending on load and temperature. These ESR limitations make designing with conventional LDOs more difficult because of their unclear specifications and the dependence of ESR over temperature. -6- REV. A ADP3307 Shutdown Mode NR ADP3307-3.3 VIN OUT IN C1 1F + Applying a high signal to the shutdown pin or tying it to the input pin will turn the output ON. Pulling the shutdown pin down to a low level or tying it to ground will turn the output OFF. In shutdown mode, quiescent current is reduced to less than 1 A. CNR 10nF R1 330k ERR EOUT + VOUT = 3.3V C2 4.7F Error Flag Dropout Detector ON The ADP3307 will maintain its output voltage over a wide range of load, input voltage and temperature conditions. If the output is about to lose regulation, for example, by reducing the supply voltage below the combined regulated output and dropout voltages, the ERR pin will be activated. The ERR output is an open collector that will be driven low. OFF SD GND Figure 3. Noise Reduction Circuit Thermal Overload Protection The ADP3307 is protected against damage due to excessive power dissipation by its thermal overload protection circuit, which limits the die temperature to a maximum of 165C. Under extreme conditions (i.e., high ambient temperature and power dissipation), where die temperature starts to rise above 165C, the output current is reduced until the die temperature has dropped to a safe level. Output current is restored when the die temperature is reduced. Once set, the ERRor flag's hysteresis will keep the output low until a small margin of operating range is restored either by raising the supply voltage or reducing the load. APPLICATIONS CIRCUITS Crossover Switch The circuit in Figure 4 shows that two ADP3307s can be used to form a mixed supply voltage system. The output switches between two different levels selected by an external digital input. Output voltages can be any combination of voltages from the Ordering Guide of the data sheet. Current and thermal limit protections are intended to protect the device against accidental overload conditions. For normal operation, device power dissipation should be externally limited so that junction temperatures will not exceed 125C. Calculating Junction Temperature VIN = 4V TO 12V Device power dissipation is calculated as follows: IN OUTPUT SELECT 5V 0V PD = (VIN - VOUT) ILOAD + (VIN) IGND Where ILOAD and IGND are load current and ground current, VIN and VOUT are input and output voltages respectively. VOUT = 2.7V/3.3V OUT ADP3307-2.7 SD GND Assuming ILOAD= 100 mA, IGND= 2 mA, VIN = 5.5 V and VOUT = 3.3 V, device power dissipation is: PD = (5.5 - 3.3) 0.1 + 5.5 x 2 mA = 0.231 W C1 1.0F + OUT IN + ADP3307-3.3 T = TJ - TA = PD x JA = 0.231 x 165 = 38C C2 0.47F SD With a maximum junction temperature of 125C, this yields a maximum ambient temperature of 87C. GND Printed Circuit Board Layout Consideration Figure 4. Crossover Switch Surface mount components rely on the conductive traces or pads to transfer heat away from the device. Appropriate PC board layout techniques should be used to remove heat from the immediate vicinity of the package. Higher Output Current The ADP3307 can source up to 100 mA without any heatsink or pass transistor. If higher current is needed, an appropriate pass transistor can be used, as in Figure 5, to increase the output current to 1 A. The following general guidelines will be helpful when designing a board layout: 1. PC board traces with larger cross section areas will remove more heat. For optimum results, use PC boards with thicker copper and wider traces. VIN = 4V TO 8V MJE253* C1 47F VOUT = 3.3V@1A R1 50 2. Increase the surface area exposed to open air so heat can be removed by convection or forced air flow. IN OUT 3. Do not use solder mask or silkscreen on the heat dissipating traces because it will increase the junction-to-ambient thermal resistance of the package. ADP3307-3.3 SD + C2 10F ERR GND *AAVID531002 HEAT SINK IS USED Figure 5. High Output Current Linear Regulator REV. A -7- ADP3307 Constant Dropout Post Regulator L1 6.8H D1 1N5817 ADP3307-3.3 VIN = 2.5V TO 3.5V C1 100F 10V IN R1 120 ILIM C00139-0-7/01(A) The circuit in Figure 6 provides high precision with low dropout for any regulated output voltage. It significantly reduces the ripple from a switching regulator while providing a constant dropout voltage, which limits the power dissipation of the LDO to 30 mW. The ADP3000 used in this circuit is a switching regulator in the step-up configuration. C2 100F 10V R2 30.1k 1% VIN SW1 SD GND Q1 2N3906 ADP3000-ADJ 3.3V@100mA OUT + C3 2.2F Q2 2N3906 FB GND R3 124k 1% SW2 R4 274k Figure 6. Constant Dropout Post Regulator OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 6-Lead Plastic Surface Mount (RT-6) 0.122 (3.10) 0.106 (2.70) 6 5 4 0.071 (1.80) 0.059 (1.50) 0.118 (3.00) 0.098 (2.50) 1 2 3 PIN 1 0.075 (1.90) BSC 0.006 (0.15) 0.000 (0.00) 0.057 (1.45) 0.035 (0.90) 0.020 (0.50) 0.010 (0.25) SEATING PLANE 0.009 (0.23) 0.003 (0.08) 10 0 0.022 (0.55) 0.014 (0.35) ADP3307-Revision History Location Page Data Sheet changed from REV. 0 to REV. A. Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Addition to the ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Edit to Calculating Junction Temperature section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Edits to Figure 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 -8- REV. A PRINTED IN U.S.A. 0.051 (1.30) 0.035 (0.90) 0.037 (0.95) BSC