[ For General Electronic Equipment (General Environment) ] Notice for TAIYO YUDEN Products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter TAIYO YUDENs official sales channel ). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDENs official sales channel. Caution for Export Some of our products listed in this catalog may require specific procedures for export according to U.S. Export Administration Regulations , Foreign Exchange and Foreign Trade Control Law of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18 WIRE-WOUND CHIP INDUCTORS (LB SERIES) WIRE-WOUND CHIP INDUCTORSLB SERIES REFLOW REFLOW PARTS NUMBER L B * Operating Temp.-40+105Including self-generated heat 2 0 1 Series name Code LB 2 T 1 0 0 M Packaging Code T Series name Wound chip inductor Packaging Taping Nominal inductance Code example 1R0 100 101 RDecimal point Characteristics Standard High current Low Rdc Low loss Nominal inductanceH STANDARD INDUCTORS INDUCTORS Characteristics Code C R MF Blank space 1.0 10 100 DimensionsLxW Code Typeinch 1608 2012 2016 2518 3218 3225 16080603 20120805 20160806 25181007 32181207 32251210 Inductance tolerance Code K M Dimensions LxWmm 1.6x0.8 2.0x1.25 2.0x1.6 2.5x1.8 3.2x1.8 3.2x2.5 Inductance tolerance 10 20 Special code Code R Special code Standard Low Rdc type Internal code STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to these products is reflow soldering W Type A L 1608 0.55 T C MF1608 0.55 2012 0.60 e 2016 0.60 2518 0.60 A B A 3218 0.85 3225 0.85 Type LB 1608 LBMF1608 LB LB LB LB LB LB LB LB 2012 C2012 R2012 2016 C2016 2518 C2518 R2518 LB 3218 LB C3225 only. B 0.7 0.7 1.0 1.0 1.5 1.7 1.7 C 0.9 1.0 1.45 1.8 2.0 2.0 2.7 Unitmm Standard quantitypcs Paper tape Embossed tape L W T e 1.60.1 0.0630.004 1.60.2 0.0630.008 0.80.1 0.0310.004 0.80.2 0.0310.008 0.80.1 0.0310.004 0.80.2 0.0310.008 0.350.15 0.0140.006 0.450.15 0.0160.006 2.00.2 0.0790.008 1.250.2 0.0490.008 1.250.2 0.0490.008 2.00.2 0.0790.008 1.60.2 0.0630.008 2.50.2 0.0980.008 3.20.2 0.1260.008 3.20.2 0.1260.008 4000 3000 0.50.2 0.0200.008 3000 1.60.2 0.0630.008 0.50.2 0.0200.008 2000 1.80.2 0.0710.008 1.80.2 0.0710.008 0.50.2 0.0200.008 2000 1.80.2 0.0710.008 2.50.2 0.0980.008 1.80.2 0.0710.008 2.50.2 0.0980.008 0.60.2 0.0240.008 0.60.3 0.0240.012 2000 1000 Unitmminch i_wound_LB_e-E05R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 87 PARTS NUMBER 16080603type Parts number LB LB LB LB LB 1608T1R0M 1608T2R2M 1608T4R7M 1608T8R2M 1608T100M Parts number LBMF1608T1R0M LBMF1608T2R2M LBMF1608T3R3M LBMF1608T4R7M LBMF1608T100[] LBMF1608T220[] LBMF1608T470[] EHS RoHS RoHS RoHS RoHS RoHS EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal inductance H 1.0 2.2 4.7 8.2 10 Nominal inductance H 1.0 2.2 3.3 4.7 10 22 47 Inductance tolerance 20 20 20 20 20 Inductance tolerance 20 20 20 20 1020 1020 1020 STANDARD INDUCTORS INDUCTORS Self-resonant frequency MHmin. 100 80 45 32 32 DC Resistance 30 0.17 0.33 0.55 0.70 0.70 Rated current mAmax. 160 115 70 60 60 Measuring frequency MHz 7.96 7.96 7.96 2.52 2.52 Self-resonant frequency MHmin. 100 80 60 45 32 16 11 DC Resistance 30 0.09 0.17 0.22 0.24 0.36 1.0 2.5 Rated current mAmax. 230 160 130 110 80 50 35 Measuring frequency MHz 7.96 7.96 7.96 7.96 2.52 2.52 2.52 Self-resonant frequency MHmin. 100 80 55 45 38 32 32 28 16 11 10 8 DC Resistance 30 0.15 0.23 0.30 0.40 0.47 0.70 0.50 1.3 1.7 3.7 6.0 7.0 Rated current mAmax. 405 260 235 190 135 120 120 100 80 60 50 45 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 Self-resonant frequency MHmin. 100 70 45 40 16 11 DC Resistance 30 0.19 0.33 0.50 1.2 3.7 5.8 Rated current mAmax. 620 430 295 200 130 90 Measuring frequency MHz 7.96 7.96 7.96 2.52 2.52 2.52 Self-resonant frequency MHmin. 100 80 45 32 16 11 8 DC Resistance 30 0.07 0.13 0.24 0.36 1.0 1.7 4.0 Rated current mAmax. 400 260 200 150 100 75 50 Measuring frequency MHz 7.96 7.96 7.96 2.52 2.52 2.52 0.796 Self-resonant frequency MHmin. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 30 0.09 0.11 0.13 0.20 0.25 0.35 0.50 0.70 1.0 1.7 2.4 3.0 4.5 Rated current mAmax. 490 380 375 285 225 200 155 130 105 85 70 55 40 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 20120805type Parts number LB LB LB LB LB LB LB LB LB LB LB LB 2012T1R0M 2012T2R2M 2012T3R3M 2012T4R7M 2012T6R8M 2012T100[] 2012T100[]R 2012T150[] 2012T220[] 2012T470[] 2012T680[] 2012T101[] Parts number LB LB LB LB LB LB C2012T1R0M C2012T2R2M C2012T4R7M C2012T100[] C2012T220[] C2012T470[] Parts number LB LB LB LB LB LB LB R2012T1R0M R2012T2R2M R2012T4R7M R2012T100[] R2012T220[] R2012T470[] R2012T101[] EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS EHS RoHS RoHS RoHS RoHS RoHS RoHS EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal inductance H 1.0 2.2 3.3 4.7 6.8 10 10 15 22 47 68 100 Nominal inductance H 1.0 2.2 4.7 10 22 47 Nominal inductance H 1.0 2.2 4.7 10 22 47 100 Inductance tolerance 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 Inductance tolerance 20 20 20 1020 1020 1020 Inductance tolerance 20 20 20 1020 1020 1020 1020 20160806type Parts number LB LB LB LB LB LB LB LB LB LB LB LB LB [] EHS 2016T1R0M RoHS 2016T1R5M RoHS 2016T2R2M RoHS 2016T3R3M RoHS 2016T4R7M RoHS 2016T6R8M RoHS 2016T100[] RoHS 2016T150[] RoHS 2016T220[] RoHS 2016T330[] RoHS 2016T470[] RoHS 2016T680[] RoHS 2016T101[] RoHS Please specify the Inductance Nominal inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 tolerance codeK or M Inductance tolerance 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. LBR series Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E05R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 88 18 PARTS NUMBER Parts number LB LB LB LB LB LB LB LB LB LB LB LB LB C2016T1R0M C2016T1R5M C2016T2R2M C2016T3R3M C2016T4R7M C2016T6R8M C2016T100[] C2016T150[] C2016T220[] C2016T330[] C2016T470[] C2016T680[] C2016T101[] EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance tolerance 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 Self-resonant frequency MHmin. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 30 0.10 0.15 0.20 0.27 0.37 0.59 0.82 1.2 1.8 2.8 4.3 7.0 8.0 Rated current mAmax. 690 600 520 410 355 290 245 200 165 135 110 95 75 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 Self-resonant frequency MHmin. 100 80 68 54 46 46 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 2.4 DC Resistance 30 0.06 0.07 0.09 0.11 0.13 0.10 0.15 0.25 0.32 0.50 0.70 0.95 1.5 2.1 3.2 4.5 7.0 10 17 24 Rated current mAmax. 665 405 340 280 240 235 195 165 145 115 95 85 70 60 45 40 30 25 20 15 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 Self-resonant frequency MHmin. 100 100 80 68 54 41 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 DC Resistance 30 0.08 0.07 0.11 0.13 0.16 0.20 0.30 0.36 0.65 0.77 1.5 1.9 2.8 3.7 6.1 8.4 12.3 22 28 Rated current mAmax. 775 890 730 630 560 510 420 375 285 250 185 165 140 125 95 80 65 50 45 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 Self-resonant frequency MHmin. 100 68 45 30 19 11 9 DC Resistance 30 0.045 0.07 0.10 0.19 0.44 0.84 1.89 Rated current mAmax. 960 480 345 235 175 120 80 Measuring frequency MHz 7.96 7.96 7.96 2.52 2.52 2.52 0.796 25181007type Parts number 2518T1R0M 2518T1R5M 2518T2R2M 2518T3R3M 2518T4R7M 2518T4R7MR 2518T6R8M 2518T100[] 2518T150[] 2518T220[] 2518T330[] 2518T470[] 2518T680[] 2518T101[] 2518T151[] 2518T221[] 2518T331[] 2518T471[] 2518T681[] 2518T102[] Parts number LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB C2518T1R0M C2518T1R0MR C2518T1R5M C2518T2R2M C2518T3R3M C2518T4R7M C2518T6R8M C2518T100[] C2518T150[] C2518T220[] C2518T330[] C2518T470[] C2518T680[] C2518T101[] C2518T151[] C2518T221[] C2518T331[] C2518T471[] C2518T681[] RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal inductance H 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 Nominal inductance H 1.0 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 Nominal inductance Parts number EHS H LB R2518T1R0M RoHS 1.0 LB R2518T2R2M RoHS 2.2 LB R2518T4R7M RoHS 4.7 LB R2518T100[] RoHS 10 LB R2518T220[] RoHS 22 LB R2518T470[] RoHS 47 LB R2518T101[] RoHS 100 [] Please specify the Inductance tolerance codeK or M Inductance tolerance 20 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 Inductance tolerance 20 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 Inductance tolerance 20 20 20 1020 1020 1020 1020 STANDARD INDUCTORS INDUCTORS LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB EHS LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. LBR series Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E05R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 89 PARTS NUMBER 32181207type Parts number STANDARD INDUCTORS INDUCTORS LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB 3218T1R0M 3218T1R5M 3218T2R2M 3218T3R3M 3218T4R7M 3218T6R8M 3218T100[] 3218T150[] 3218T220[] 3218T330[] 3218T470[] 3218T680[] 3218T101[] 3218T151[] 3218T221[] 3218T331[] 3218T471[] 3218T681[] 3218T102[] EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 Inductance tolerance 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 1020 Self-resonant frequency MHmin. 100 80 68 54 41 40 30 25 19 15 12 11 8.0 7.0 5.0 4.0 3.5 3.0 2.4 DC Resistance 30 0.06 0.07 0.09 0.11 0.13 0.17 0.25 0.32 0.49 0.75 0.92 1.49 2.4 3.2 5.4 7.0 14 17 27 Rated current mAmax. 1,075 860 775 560 550 380 340 300 255 215 205 145 140 105 80 65 54 45 39 Measuring frequency MHz 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 Self-resonant frequency MHmin. 250 220 190 160 70 50 23 20 17 13 10 8 6 DC Resistance 30 0.055 0.060 0.080 0.095 0.100 0.120 0.133 0.195 0.27 0.41 0.67 1.0 1.4 Rated current mAmax. 1,100 1,000 930 820 680 620 540 420 330 300 220 190 150 Measuring frequency MHz 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 32251210type Parts number EHS LB C3225T1R0MR RoHS LB C3225T1R5MR RoHS LB C3225T2R2MR RoHS LB C3225T3R3MR RoHS LB C3225T4R7MR RoHS LB C3225T6R8MR RoHS LB C3225T100[]R RoHS LB C3225T150[]R RoHS LB C3225T220[]R RoHS LB C3225T330[]R RoHS LB C3225T470[]R RoHS LB C3225T680[]R RoHS LB C3225T101[]R RoHS [] Please specify the Inductance Nominal inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 tolerance codeK or M Inductance tolerance 20 20 20 20 20 20 1020 1020 1020 1020 1020 1020 1020 LB/LBC series Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias. i_wound_LB_e-E05R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 90 18 WIRE-WOUND CHIP INDUCTORS (LB SERIES) WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES) WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) PACKAGING Minimum Quantity Standard Quantity pcs Paper Tape Embossed Tape Type LB C3225 CB C3225 LB 3218 LB R2518 LB C2518 LB 2518 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 CB 2012 CB C2012 CB L2012 LB 1608 LBMF1608 CBMF1608 1000 2000 2000 2000 3000 4000 4000 3000 Tape material Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 Taping Dimensions Embossed Tape 0.315 inches wide A B F Type LBM2016 LB C3225 CB C3225 LB 3218 LB 2518 CB 2518 LB C2518 CB C2518 LB R2518 LB 2016 CB 2016 LB C2016 CB C2016 LB 2012 CB 2012 LB C2012 CB C2012 LB R2012 LBMF1608 CBMF1608 1.750.1 (0.0690.004 8.00.3 (0.3150.012) 1.50.1/0 (0.0590.004/-0) 3.50.05 (0.1380.002) Sprocket hole 4.00.1 (0.1570.004) 2.00.1 (0.0790.004) Chip cavity A B 1.750.1 2.10.1 0.0690.004 0.0830.004 2.80.1 3.50.1 0.1100.004 0.1380.004 2.10.1 3.50.1 0.0830.004 0.1380.004 Insertion pitch F 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 Tape thickness T K 0.30.05 1.9max. 0.0120.002 0.075max. 0.30.05 4.0max. 0.0120.002 0.157max. 0.30.05 2.2max. 0.0120.002 0.087max. 2.150.1 0.0850.004 2.70.1 0.1060.004 4.00.1 0.1570.004 0.30.05 0.0120.002 2.2max. 0.087max. 1.750.1 0.0690.004 2.10.1 0.0830.004 4.00.1 0.1570.004 0.30.05 0.0120.002 1.9max. 0.075max. 1.450.1 0.0570.004 2.250.1 0.0890.004 4.00.1 0.1570.004 0.250.05 0.0100.002 1.45max. 0.057max. 1.10.1 0.0430.004 1.90.1 0.0750.004 4.00.1 0.1570.004 0.250.05 0.0100.002 1.2max. 0.047max. Unitmminch Insertion pitch F 4.00.1 0.1570.004 4.00.1 0.1570.004 Tape thickness T 1.1max. 0.043max. 1.1max. 0.043max. Unitmminch Card board carrier tape0.315 inches wide A B F Type CB L2012 LB 1608 1.750.1 (0.0690.004 T 8.00.3 (0.3150.012) 1.50.1/0 (0.0590.004/-0) 3.50.05 (0.1380.002) Sprocket hole 4.00.1 (0.1570.004) 2.00.1 (0.0790.004) Chip cavity A B 1.550.1 2.30.1 0.0610.004 0.0910.004 1.00.1 1.80.1 0.0390.004 0.0710.004 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 Leader and Blank Portion Reel Size Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series 40105Including self-generated heat LBM Series 2. Storage Temperature Rangeafter soldering LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series 4085 LBM Series Test Methods and Remarks LB, CB Series Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMFCBMFLBM Series Measuring equipment LCR MaterHP4285A or its equivalent Measuring frequency : Specified frequency 5.Q LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks LBM Series Measuring equipment Measuring frequency Within the specified tolerance : LCR MaterHP4285A or its equivalent : Specified frequency 6.DC Resisitance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks Measuring equipment : DC Ohmmeter HIOKI 3227 or its equivalent 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks Measuring equipment : Impedance analyzer HP4291A or its equivalent This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 8.Temperature Characteristic LBM2016 Specified Value Test Methods and Remarks Inductance change : Within5 LB1608 LB2012 LBR2012 CB2012 CBL2012 LB2016 CB2016 LB2518 LBR2518 CB2518 LBC3225 CBC3225 LBMF1608 CBMF1608 LBC2016 CBC2016 LBC2518 CBC2518 LB3218 LBC2012 CBC2012 Inductance change : Within20 Inductance change : Within25 Inductance change : Within35 Based on the inductance at 20 and Measured at the ambient of 4085. 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Warp : 2mmLBLBCLBRCBCBCCBLLBMLBMFCBMF Series Test substrate : Glass epoxy-resin substrate Thickness : 0.8mmLB1608LBMF1608CBMF1608 : 1.0mmOthers Test Methods and Remarks 10.Body Strength LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBM Applied force : 10N Duration : 10sec. LB1608LBMF1608CBMF1608 Applied force : 5N Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No abnormality. LBM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMLBMFCBMF Applied force : 10N to X and Y directions Duration : 5 sec. Test substrate : Printed board LB1608CBMF1608LBMF1608 Applied force : 5N to X and Y directions Duration : 5 sec. Test substrate : Printed board This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 12.Resistance to vibration LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within5 No significant abnormality in appearance. LBM Series Test Methods and Remarks Inductance change : Within10 No significant abnormality in appearance. LBLBRLBCCBCBCCBLLBMLBMFCBMF The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 1055Hz Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series 14.Solderability LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series At least 90 of surface of terminal electrode is covered by new LBM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMLBMFCBMF Solder temperature : 2455 Duration : 50.5sec Flux : Methanol solution with 25 of colophony 15.Resistance to soldering LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks Inductance change : Within10 Inductance change : Within5 LBLBCLBRCBCBCCBLLBMLBMFCBMF 3 times of reflow oven at 230 MIN for 40sec. with peak temperature at 260 for 5sec. Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks Solvent temperature Type of solvent Cleaning conditions : Room temperature : Isopropyl alcohol : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within10 No significant abnormality in appearance. LBM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMLBMFCBMF The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature () Duration (min) 1 403 303 2 Room temperature Within 3 3 852 303 4 Room temperature Within 3 Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 18.Damp heat life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within10 No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Humidity Duration Recovery : 602 : 9095RH : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series Specified Value Test Methods and Remarks Inductance change : Within10 No significant abnormality in appearance. LBM Series Temperature Humidity Duration Applied current Recovery : 602 : 9095RH : 1000 hrs : Rated current : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test Specified Value LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series Inductance change : Within10 No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Duration Recovery : 852 : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks Temperature Duration Applied current Recovery Inductance change : Within10 LBC3225 Series : Within20 No significant abnormality in appearance. : 852 : 1000 hrs : Rated current : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within10 No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Duration Recovery : 402 : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Standard test conditions Unless specified, Ambient temperature is 2015 and the Relative humidity is 6520. If there is any doubt about the test results, further measurement shall be had within the following limits: Ambient Temperature: 202 Relative humidity: 655 Inductance value is based on our standard measurement systems. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 WIRE-WOUND CHIP INDUCTORS (LB SERIES) WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES) WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) PRECAUTIONS 1Circuit Design Precautions Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2PCB Design Precautions Technical considerations Land pattern design 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS Recommended Land Patterns Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to those products is reflow soldering only. 3Considerations for automatic placement Precautions Technical considerations Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4Soldering Precautions Reflow soldering LB and CB Types 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. Reflow soldering LB and CB Types 1. Reflow profile Technical considerations Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5Cleaning Precautions Technical considerations Cleaning conditions Washing by supersonic waves shall be avoided. Cleaning conditions If washed by supersonic waves, the products might be broken. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01 6Handling Precautions Technical considerations Handling 1. Keep the inductors away from all magnets and magnetic objects. Breakaway PC boards splitting along perforations 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. Handling 1. There is a case that a characteristic varies with magnetic influence. Breakaway PC boards splitting along perforations 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7Storage conditions Precautions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature : 040 Humidity : Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Taiyo Yuden: LB1608T1R0M LB1608T2R2M LB1608T4R7M LB1608T8R2M LB2012T100K LB2012T100KR LB2012T100M LB2012T100MR LB2012T101K LB2012T101M LB2012T150K LB2012T1R0M LB2012T220K LB2012T220M LB2012T2R2M LB2012T3R3M LB2012T470K LB2012T470M LB2012T4R7M LB2012T680K LB2012T6R8M LB2016T100K LB2016T100M LB2016T101K LB2016T101M LB2016T150K LB2016T150M LB2016T1R0M LB2016T1R5M LB2016T220K LB2016T220M LB2016T2R2M LB2016T330K LB2016T330M LB2016T3R3M LB2016T470K LB2016T470M LB2016T4R7M LB2016T680K LB2016T680M LB2016T6R8M LB2518T100K LB2518T100M LB2518T101K LB2518T101M LB2518T102K LB2518T102M LB2518T150K LB2518T150M LB2518T151K LB2518T151M LB2518T1R0M LB2518T1R5M LB2518T220K LB2518T220M LB2518T221K LB2518T221M LB2518T2R2M LB2518T330K LB2518T330M LB2518T331K LB2518T331M LB2518T3R3M LB2518T470K LB2518T470M LB2518T471K LB2518T471M LB2518T4R7M LB2518T680K LB2518T680M LB2518T681K LB2518T681M LB2518T6R8M LB3218T100K LB3218T100M LB3218T101K LB3218T101M LB3218T102K LB3218T102M LB3218T150K LB3218T150M LB3218T151K LB3218T151M LB3218T1R0M LB3218T1R5M LB3218T220K LB3218T220M LB3218T221K LB3218T221M LB3218T2R2M LB3218T330K LB3218T330M LB3218T331K LB3218T331M LB3218T3R3M LB3218T470K LB3218T470M LB3218T471K LB3218T471M LB3218T4R7M