OM13513UL - NXP SEMICONDUCTORS

UM10762

User manual for the accurate RTC demo board OM13513

containing PCF2127T and PCF2129AT

Rev. 2 — 1 September 2014 User manual

Document information

Info Content

Keywords PCF2127T, PCF2129AT, OM13513, accurate RTC, Real-Time Clock, get

started, SPI bus, I2C-bus, time stamp, temperature compensation,

integrated quartz, tuning, battery switch, Watch-Dog

Abstract User manual for the accurate RTC demo board OM13513 containing

PCF2127T and PCF2129AT

User manual Rev. 2 — 1 September 2014 2 of 20

Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

Revision history

Rev Date Description

v.2 20140901 updated revision

v.1 20140602 first revision

User manual Rev. 2 — 1 September 2014 3 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

1. Introduction

The PCF2127, PCA2129 and PCF2129 are a family of very accurate Real-Time Clocks.

They feature a fully integrated temperature compensated quartz oscillator (TCXO). Time

stamp, battery management and watchdog blocks reduce the system overhead

considerably.

The OM13513 is the i deal evaluation and demo boa rd to be used during the design pha se

of any project; only power and a serial bus (SPI-bus or I2C-bus) need to be connected.

The OM13518 (USB to I2C-bus dongle) could be used for the I2C-bus conn ection.

2. Key features

2.1 Evaluation board OM13513

The accurate RTCs PCF2127T and PCF2129AT are mounted together with a back-up

lithium battery on a small PC-board. Two push buttons allow initiating time stamps .

All signals are accessible on the pin connectors P2 and P3 (see Figure 4), overcoming the

need to build a test PC-board before the circuit can be evaluated or the functionality can

be tested together with the final application.

The board is also helpful to evaluate the functionality of PCF2127AT, PCF2129T and

PCA2129T/Q900, the automotive grad e version. Also check section Section 2.3.

User manual Rev. 2 — 1 September 2014 4 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

2.2 Accurate RTC

The specific features of the accurate RTC are complementing the main functionality.

PCF2127T and PCF2129AT:

•Temperature compensated quartz oscillator TCXO with embedded quartz crystal

–Typical accuracy: 3ppm

•Battery backup input pin and switch-over circuitry

•Battery backed output voltage

•Universal interface to select between SPI- and I2C-bus

•Time stamp facility

–With interrupt capability

–Detection of two different events on one mu ltilevel input pin (for example, for

tamper detection)

•Programmable watchdog timer with interrupt

For configuring the board, see Section 3.4.

Fig 1. OM13513 evaluation/demo board

I2C

SPI

User manual Rev. 2 — 1 September 2014 5 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

•Programmable alarm function with interrupt capability

In addition PCF2127T has the following features:

•512 Byte of battery buffered RAM

•Programmable countdown timer with interrupt

•Additional power fail detector to, for example, pre-alert the microcontroller that the

power supply is going down

The block diagram in Figure 2 nicely illustrates the key blocks:

•Time stamp facility

•Temperature compensated quartz oscillator TCXO

•Battery back-up switch

•Universal interface to select between SPI-bus and I2C-bus

2.3 Accurate Real-Time Clock PCF2127T, PCF2129AT

The high accuracy is achieved by the integration of a temperature compensated quartz

oscillator including the quartz crystal in one package. Additional features are battery

management, time stamp facility and in case of the PCF2127T additional 512 bytes of

battery buffered RAM.

There are 3 different grades available:

1. Temperature compensa tion co verin g 25 C t o +6 5 C: PCF2127AT, PCF2129AT (on

the OM13513)

Fig 2. Block diagram of the accurate RTC family

User manual Rev. 2 — 1 September 2014 6 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

2. Temperature compensation covering 40 C to +85 C: PCF2127T (on the

OM13513), PCF2129T

3. Automotive grade AEC-Q100 covering 40 C to +85 C: PCA2129T/Q900

1. uses a quartz crystal packed in a metal can package.

2. and 3. use a quartz, packed in a ceramic package.

2.4 Expected accuracy

The accuracy of an RTC is commonly specified in deviation of seconds per day or ppm ;

1 s/day corresponds to 11.5ppm.

The PCF2127AT and PCF2129AT are temperature compensated over the temperature

range of 30 Cto +60C and the PCF2127T, PCF2129T and PCA2129T/Q900 are

temperature compensated over the temperature range of 40 C to +85 C, see Figure 3.

Since the actual deviations at different temperatures may be positive (running to fast) or

negative (running too slow) they may cancel out each other to a high extend. Therefore

the actual accuracy over timer is much better than specified in with the max values;

< 3 ppm or 1 s/4days can be expected. Other consideration regard the ambient

temperature over the day, respectively over the yea r. Temperatures below e.g. 15C and

above +60 C are usu ally on ly present for a limited time of the da y an d ma y ev en not be

present most of the year.

User manual Rev. 2 — 1 September 2014 7 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

Fig 3. Temperature compensation gradat ion in respect to family

Temperature (°C)

-40 1006008040-20 20

001aaj650

-40

Frequency

stability

(ppm)

-80

± 10 ppm ± 5 ppm ± 10 ppm

(1)

(2)

Temperature (°C)

-40 1006008040-20 20

013aaa345

-40

Frequency

stability

(ppm)

-80

± 5 ppm ± 3 ppm ± 5 ppm

(1)

(2)

PCF2127AT

PCF2129AT

PCF2127T

PCA2129T

PCF2129T

User manual Rev. 2 — 1 September 2014 8 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

3. Hardware setup

3.1 Detailed circuit diagram

The position of the jumpe rs and conn ecto rs can be found in the circuit di ag ram ( Figure 4)

and the layout drawing (Figure 5).

3.2 General requirements for the PCF2127T and PCF2129AT

The RTC circuit just requires a few external components to buffer the supply voltage.

Avoid any tracks with high frequency signals (fast edges) close to the RTC or its

connections.

It is required to have a decoupling capacitor of 100 nF on the VDD-VSS rails close to the

RTC; a similar decoupling capacitor on pin BBS is required. Due to the low power

consumptio n of a fe w μW, no precautions for heat dissipations are required, even in a

sealed housing environment.

Frequencies of 1 Hz to 16.884 kHz at the CLKOUT pin can be used to measure the

frequency for calibration and/or for general purpose use, e.g. as reference for the

frequency generation with a PLL. If the CLKOUT frequency is set to 32.768 kHz, then the

accuracy may be less.

Fig 4. Circuit diagram of the demo board OM13513

Comment

100nF

GND

VDD

SCL

SDA/CEn2

SDI

SDO

TSn

INTA1

12 34 56 78 910 1112 1314

SCL1

INTA1

GND

3V3

Res

SDA1

SDA2

INTA2

GND

3V3

Res

SCL2

CLKOUT2

100nF

10uF

GND

SDA

SCL

VDDVSS

VBAT

IC1/PW IC2/PW

VSS

VBAT

BT1

VDD U1 VDD U2

VDD

GND

3.3V

CR2032

SCL

1SDI

2SDO

3SDA/CEn

4IFS

5TSn

6CLKOUT

7VSS

8TEST 9

PFOn 10

PFI 11

RSTn 12

INTn 13

BBS 14

VBAT 15

VDD 16

PCF2127T

IC2

TSn

SDO

3SDA/CEn

4IFS

CLKOUT

7VSS

8n.c

9n.c

10 n.c 11

n.c 12

n.c 13

n.c 14

n.c 15

n.c 16

SDI

INTn 17

BBS 18

VBAT 19

VDD 20

SCL

PCF2129AT

IC1

2K2

SDA/CEn2

SDA/CEn1

10k

J7 BBS

VSS

IFS2

BBS

VSS

IFS1

CLKOUT1

PFI

PFOn

RSTn

TEST

GND

JP1

220k

1 2

JP2

1 2

JP3

47K

1 2

JP4

820E

VDD

100nF

J3 for future use

Optional connector

User manual Rev. 2 — 1 September 2014 9 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

3.3 Battery back-up

To guarantee the autonomy of the clock a continuous supply of power is needed. The

battery back-up facility will assure this. For storage and delivery the jumpers J5 and J6 are

set such that the battery will not be discharged.

To reduce power consumption, always switch-of f functions and outputs not in use.

3.4 Hardware settings

3.4.1 General settings

•Set Jumper JP4 to activate LED D1 for signaling an interrupt

•The single in line connectors P2 and P3 (100 mil pitch) give access to all pins for

integrating the RTC into an application

•Resistor R1 and C1 reduce the VDD slew rate when removing VDD to ensure clean

battery switch over

•A Lithium coin cell battery 2032 is mo unted underneath the boar d to buffer the vo ltage

in case of loss of supply voltage VDD

•Jumper J1, respectively J2 allows to measure the current consumption, replace it by a

A meter

Fig 5. Evaluation board (top side layout)

User manual Rev. 2 — 1 September 2014 10 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

3.4.2 Settings for PCF2129AT (IC1)

Default jumper settings to operate PCF2129AT and disable PCF2127T on the boa rd .T h e

hardware settings are illustrated in Figure 6.

Fig 6. Hardware settings for PCF2129AT

F E

VSS

I2C

SPI

User manual Rev. 2 — 1 September 2014 11 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

[1] In direction of reading “Jn”.

Table 1. Jumper settings to operat e PCF2129AT (IC1)

Indicator Description Jumper Setting[1]

Jumpers

DD selected for PCF2129AT J1 ■■

B battery backup of PCF 2129AT enabled J6 □■■

C battery backup of PCF 2127T disabled J5 ■■□

D LED D1 connected to interrupt pin JP4 ■■

2C-bus selected for the PCF2129AT J4 □■■

SPI-bus selected for the PCF2129AT ■■□

G unused SDI-interface connected to GND JP1 ■■

H pull-up on CLKOUT JP2 -

Interface

I supply and interface connector P2 -

Outputs

J interrupt output P2 -

K clock output P3 -

User manual Rev. 2 — 1 September 2014 12 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

3.4.3 Settings for PCF2127T (IC2)

Default jumper settings to operate PCF2127T and disable PCF2129AT on the board.The

hardware settings are illustrated in Figure 7.

Fig 7. Hardware settings for PCF2127T

VSS

I2C

SPI

User manual Rev. 2 — 1 September 2014 13 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

[1] In direction of reading “Jn”.

Table 2. Jumper settings to operat e the PCF2127T (IC2)

Indicator Description Jumper Setting[1]

Jumpers

DD selected for PCF2127T J2 ■■

B battery backup of PCF2127T enabled J5 □■■

C battery backup of PCF2129AT disabled J6 ■■□

D LED D1 connected to interrupt pin JP4 ■■

2C-bus selected for the PCF2127T J7 □■■

SPI-bus selected for the PCF2127T ■■□

G unused SDI-interface connected to GND JP1 ■■

H pull-up on CLKOUT JP2 -

Interface

I supply and interface connector P2 -

Outputs

J interrupt output P2 -

K clock output P3 -

Push button

L time stamp input 1 T1 -

M time stamp input 2 T1 -

User manual Rev. 2 — 1 September 2014 14 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

4. Optional features for test and evaluation

4.1 Experimental area

Left of the NXP logo there is some space on the board where a custom circuitry can be

placed. VSS and VDD are available for easy set up.

5. Software

The accurate RTC is controlled via a standard SPI-bus or an FM+ I2C-bus inter face.

Common protocols apply. After power-up the cont rol register has to be programmed first

to set the correct functions and modes. Then the current time should be programmed.

5.1 Software instructions for setting the clock

5.1.1 Configuring the function

Control registers 00h to 02h.

5.1.2 Setting the time

Time and date registers 03h to 09h.

5.1.3 Programming alarms

Alarm registers 0Ah to 0Eh.

5.1.4 Clock out control

5.1.5 Watchdog

Registers 10h, 11h.

5.1.6 Time stamp

Registers 12h to 18 h .

5.1.7 Aging compensation

5.1.8 RAM, PCF2127 only

Registers 1Ah to 1Dh.

5.1.9 Frequency trimming

Since the oscillator is factory calibrated, there is no need for trimming. Optional trimming

can be done to compensate for aging or to set purposely an offset to the nominal

frequency. Just program the register 19h accordingly.

User manual Rev. 2 — 1 September 2014 15 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

5.2 I2C-bus software example

Set time to 9:45:37, Aug. 1 2014

Generate a blinking LED at the Seconds interrupt:

Table 3. I2C-bus software example

Address Value Function

- S START condition

- A2h slave address + R/W = 0

- 00h register address

00h 01h e nable seconds interrupt

01h 00h d efault values

02h 00h d efault values

03h 37h set to 37 se conds

04h 45h set to 45 mi nutes

05h 09h set to 9 hours

06h 01h set to day 1

07h 05h set to Friday

08h 08h set to August

09h 14h set to year 14

- P STOP condition

- S START condition

- A2h slave address + R/W = 0

- 0Fh register address

0Fh 01h set CLKOUT freque ncy to

16 kHz

10h 23h select pulsed interrupt signal

- P STOP condition

User manual Rev. 2 — 1 September 2014 16 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

6. References

[1] PCF2127T — Accurate RTC with integrated quartz cryst al for industrial

[2] PCA2129T — Accurate RTC with integrated quartz crystal for automotive, data

sheet

[3] PCF2129AT — Integrated RTC, TCXO and quartz crystal

[4] AN11266 — Application and soldering information for the PCF2127T industrial

TCXO RTC, Application note

[5] AN10857 — Application and soldering information for PCF2127A and PCF2129A

TCXO RTC

[6] AN11120 — Application and so ldering information for the PCA2129 autom otive

TCXO RTC

User manual Rev. 2 — 1 September 2014 17 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

7. Legal information

7.1 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

7.2 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information. NXP Se miconductors takes no

responsibility for the content in this document if provided by an inf ormation

source outside of NXP Semiconductors.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whethe r or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ aggreg ate and cumulative l iability towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suit able for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors prod ucts in such equipment or

applications and theref ore such inclusi on and/o r use is at the cu stome r’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

specified use without further testing or modificat i on.

Customers are responsible for the design and operation of their applications

and products using NXP Semiconductors pr oducts, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suit able and fit for the custome r’s applications and

products planned, as well as fo r the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liability related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by custo mer’s

third party customer(s). Customer is responsible for doing all necessary

testing for th e customer’s applications and product s using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by customer’s third p arty

customer(s). NXP does not accept any liability in this respect.

Export control — This document as well as the item(s) described herein

may be subject to export control regulatio ns. Export might require a prior

authorization from competent authorities.

Evaluation products — This product is provided on an “as is” and “with all

faults” basis for eval uation purposes only. NXP Semiconductors, its affiliates

and their supplie rs expressly disclaim all warrant ies, whether express, impl ied

or statutory, including but not limited to the implied warranties of

non-infringement, mercha ntability and fitness for a part icular purpose. The

entire risk as to the quality, or arising out of the use or performance, of this

product remains with customer.

In no event shall NXP Semiconductors, it s aff iliates or thei r suppliers be liable

to customer for any special, indirect, consequ ential, punitive or incidental

damages (including without li mit ation d amages for l oss of bu siness, bu siness

interruption, loss of use , loss of data or information, and the like) arising out

the use of or inability to use the product, whet her or not based on tort

(including negligence), st rict liability, breach of contract, breach of warrant y or

any other theory, even if advised of the possibility of such damages.

Notwithstanding any damages that customer might incur for any reason

whatsoever (including without limitation, all damages referenced above and

all direct or general damages), the entire liability of NXP Semiconductors, its

affiliates and their suppliers and customer’s exclusive remedy for all of the

foregoing shall be limited to actual damages incurred by customer based on

reasonable reliance up to the greater of the amount actually paid by customer

for the product o r five dollars (U S$5.00). The for egoing limita tions, exclusions

and disclaimers shall apply to the maximum extent permitt ed by applicable

law, even if any remedy fails of its essential purpose.

Translations — A non-English (translated) version of a document is for

reference only. The English version shall prevail in case of any discrepancy

between the translated and English versions.

7.3 Trademarks

Notice: All refe renced brands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

User manual Rev. 2 — 1 September 2014 18 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

8. Tables

Table 1. Jumper settings to operate PCF2129AT (IC1) .11

Table 2. Jumper settings to operate the PCF212 7T (IC2) .

Tab le 3. I 2C-bus software example . . . . . . . . . . . . . . . .1 5

User manual Rev. 2 — 1 September 2014 19 of 20

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

9. Figures

Fig 1. OM13513 evaluation/demo board . . . . . . . . . . . . .4

Fig 2. Block diagram of the accurate RTC family. . . . . . .5

Fig 3. Temperature compensation gradation in respect to

family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Fig 4. Circuit diagram of the demo board OM13513 . . . .8

Fig 5. Evaluation board (top side layout) . . . . . . . . . . . . .9

Fig 6. Hardware settings for PCF2129AT . . . . . . . . . . .10

Fig 7. Hardware settings for PCF2127T . . . . . . . . . . . .12

NXP Semiconductors UM10762

RTC PCF2127T, PCF2129AT evaluation board OM13513

For more information, please visit: http://www.nxp.co m

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 1 September 2014

Document identifier: UM10762

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

10. Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Key features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Evaluation board OM13513 . . . . . . . . . . . . . . . 3

2.2 Accurate RTC. . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.3 Accurate Real-Time Clock PCF2127T,

PCF2129AT . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Expected accuracy. . . . . . . . . . . . . . . . . . . . . . 6

3 Hardware setup . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 Detailed circuit diagram . . . . . . . . . . . . . . . . . . 8

3.2 General requi rements for the PCF2127T and

PCF2129AT . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Battery back-up . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Hardware settings. . . . . . . . . . . . . . . . . . . . . . . 9

3.4.1 General settings . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4.2 Settings for PCF2129AT (IC1) . . . . . . . . . . . . 10

3.4.3 Settings for PCF2127T (IC2) . . . . . . . . . . . . . 12

4 Optional features for test and evalu ation . . . 14

4.1 Experimental area . . . . . . . . . . . . . . . . . . . . . 14

5 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1 Software instructions for setti n g th e cl ock . . . 14

5.1.1 Configuring the function . . . . . . . . . . . . . . . . . 14

5.1.2 Setting the time. . . . . . . . . . . . . . . . . . . . . . . . 14

5.1.3 Programming alarms . . . . . . . . . . . . . . . . . . . 14

5.1.4 Clock out control. . . . . . . . . . . . . . . . . . . . . . . 14

5.1.5 Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1.6 Time stamp. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1.7 Aging compensation. . . . . . . . . . . . . . . . . . . . 14

5.1.8 RAM, PCF2127 only. . . . . . . . . . . . . . . . . . . . 14

5.1.9 Frequency trimming . . . . . . . . . . . . . . . . . . . . 14

5.2 I2C-bus software example . . . . . . . . . . . . . . . 15

6 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7 Legal information. . . . . . . . . . . . . . . . . . . . . . . 17

7.1 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.2 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.3 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

8 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

9 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

10 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20