LM2614 400mA Sub-Miniature Adjustable DC-DC Converter Optimized for RF Power Amplifiers General Description Key Specifications The LM2614 DC-DC converter is optimized for powering RF power amplifiers (PAs) from a single Lithium-Ion cell. It steps down an input voltage of 2.8V to 5.5V to an output of 1.0V to 3.6V at up to 400mA (300mA for B grade). Output voltage is set using an analog input to VCON in the application circuit. The device offers three modes for mobile phones and similar RF PA applications. Fixed-frequency PWM mode minimizes RF interference. A SYNC input allows synchronizing the switching frequency in a range of 500kHz to 1MHz. Low current hysteretic PFM mode reduces quiescent current to 160A (typ.). Shutdown mode turns the device off and reduces battery consumption to 0.02A (typ.). Current limit and thermal shutdown features protect the device and system during fault conditions. The LM2614 is available in a 10 bump micro SMD package. This packaging uses National's chip-scale micro SMD technology and offers the smallest possible size. A high switching frequency (600kHz) allows use of tiny surface-mount components. The LM2614 can be dynamically controlled for output voltage changes from 1.0V to 3.6V in < 30s. The device features external compensation to tailor the response to a wide range of operating conditions. Operates from a single LiION cell (2.8V to 5.5V) Adjustable output voltage (1.0V to 3.6V) 1% DC feedback voltage precision 400mA maximum load capability(300mA for B grade) 600A typ PWM mode quiescent current 0.02A typ shutdown current 600kHz PWM switching frequency SYNC input for PWM mode frequency synchronization from 500kHz to 1MHz n High efficiency (96% typ at 3.9VIN, 3.6VOUT and 200mA) in PWM mode from internal synchronous rectification n 100% Maximum Duty Cycle for Lowest Dropout n n n n n n n n Features n n n n n n n Sub-miniature 10-bump thin micro SMD package Uses small ceramic capacitors 5mV typ PWM mode output voltage ripple(COUT = 22F) Internal soft start Current overload protection Thermal Shutdown External compensation Applications n n n n (c) 2002 National Semiconductor Corporation DS200367 Mobile Phones Hand-Held Radios RF PC Cards Battery Powered RF Devices www.national.com LM2614 400mA Sub-Miniature Adjustable DC-DC Converter Optimized for RF Power Amplifiers August 2002 LM2614 Typical Application Circuits 20036701 FIGURE 1. Typical Circuit for Powering RF Power Amplifiers 20036702 FIGURE 2. Typical Circuit for 2.5V Output Voltage 20036703 FIGURE 3. Typical Circuit for 1.5V Output Voltage www.national.com 2 LM2614 Connection Diagrams 10-Bump micro SMD Package 20036704 20036705 Top View Bottom View Ordering Information Order Number Package Type NSC Package Marking (*) LM2614ATL LM2614BTL LM2614ATLX 10-bump Wafer Level Chip Scale (micro SMD) LM2614BTLX Supplied As XYTT S50A 250 Tape and Reel XYTT S50B 250 Tape and Reel XYTT S50A 3000 Tape and Reel XYTT S50B 3000 Tape and Reel (*) XY - denotes the date code marking (2 digit) in production (*) TT - refers to die run/lot traceability for production (*) S - product line designator Package markings may change over the course of production. Pin Description Pin Number Pin Name A1 FB Function B1 EANEG Inverting input of error amplifier C1 EAOUT Output of error amplifier D1 SYNC/MODE D2 EN D3 PGND C3 SW B3 PVIN Power Supply Voltage Input to the internal PFET switch. Connect to the input filter capacitor. A3 VDD Analog Supply Input. If board layout is not optimum, an optional 0.1F ceramic capacitor is suggested. A2 SGND Feedback Analog Input. Synchronization Input. Use this digital input for frequency selection or modulation control. Set: SYNC/MODE = high for low-noise 600kHz PWM mode SYNC/MODE = low for low-current PFM mode SYNC/MODE = a 500kHz-1MHz external clock for synchronization in PWM mode. (See Synchronization and Operating Modes in the Device Information section.) Enable Input. Set this Schmitt trigger digital input high for normal operation. For shutdown, set low. Set EN low during system power-up and other low supply voltage conditions. (See Shutdown Mode in the Device Information section.) Power Ground Switching Node connection to the internal PFET switch and NFET synchronous rectifier. Connect to an inductor with a saturation current rating that exceeds the max Switch Peak Current Limit of the LM2614. Analog and Control Ground 3 www.national.com LM2614 Absolute Maximum Ratings (Note 1) Storage Temperature Range Lead Temperature (Soldering, 10 sec.) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. PVIN, VDD to SGND EN, EAOUT, EANEG, SYNC/MODE to SGND FB, SW 260C Junction Temperature (Note 2) -0.2V to +6V PGND to SGND, PVIN to VDD -45C to +150C -25C to +125C 2 kV Minimum ESD Rating -0.2V to +0.2V (Human Body Model, C = 100 pF, R = 1.5 k) Thermal Resistance (JA) (Note 3) 140C/W -0.2V to +6V (GND -0.2V) to (VDD +0.2V) Electrical Characteristics Specifications with standard typeface are for TA = TJ = 25C, and those in boldface type apply over the full Operating Temperature Range of TA = TJ = -25C to +85C. Unless otherwise specified, PVIN = VDD = EN = SYNC/MODE = 3.6V. Symbol Parameter Conditions Min Typ Max Units VIN Input Voltage Range VFB Feedback Voltage VHYST PFM Comparator Hysteresis Voltage PFM Mode (SYNC/MODE = 0V) (Note 5) ISHDN Shutdown Supply Current VIN = 3.6V, EN = 0V 0.02 3 A IQ1_PWM DC Bias Current into VDD SYNC/MODE = VIN FB = 2V 600 725 A SYNC/MODE = 0V FB = 2V 160 195 A IQ2_PFM PVIN = VDD = VIN (Note 4) 2.8 3.6 5.5 V 1.485 1.50 1.515 V 24 mV RDSON (P) Pin-Pin Resistance for P FET 395 550 m RDSON (N) Pin-Pin Resistance for N FET 330 500 m RDSON (TC) FET Resistance Temperature Coefficient 0.5 ILIM Switch Peak Current Limit (Note 6) VIH Logic High Input, EN, SYNC/MODE VIL Logic Low Input, EN, SYNC/MODE FSYNC SYNC/MODE Clock Frequency Range FOSC Internal Oscillator Frequency Tmin %/C LM2614ATL 510 690 850 LM2614BTL 400 690 980 0.95 1.3 0.4 (Note 7) 0.80 500 1000 LM2614ATL, PWM Mode 468 600 732 450 600 750 200 V V LM2614BTL, PWM Mode Minimum ON-Time of PFET Switch in PWM Mode mA kHz kHz ns Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but device specifications may not be guaranteed. For guaranteed specifications and associated test conditions, see the Min and Max limits and Conditions in the Electrical Characteristics table. Typical (typ) specifications are mean or average values at 25C and are not guaranteed. Note 2: Thermal shutdown will occur if the junction temperature exceeds 150C. Note 3: Thermal resistance specified with 2 layer PCB (0.5/0.5 oz. cu). Note 4: The LM2614 is designed for mobile phone applications where turn-on after system power-up is controlled by the system controller. Thus, it should be kept in shutdown by holding the EN pin low until the input voltage exceeds 2.8V. Note 5: The hysteresis voltage is the minimum voltage swing on the FB pin that causes the internal feedback and control circuitry to turn the internal PFET switch on and then off during PFM mode. When resistor dividers are used like in the operating circuit of Figure 4, the hysteresis at the output will be the value of the hysteresis at the feedback pin times the resistor divider ratio. In this case, 24mV (typ) x ((46.4k + 33.2k)/33.2k). Note 6: Current limit is built-in, fixed, and not adjustable. If the current limit is reached while the voltage at the FB pin is pulled below 0.7V, the internal PFET switch turns off for 2.5s to allow the inductor current to diminish. Note 7: SYNC driven with an external clock switching between VIN and GND. When an external clock is present at SYNC; the IC is forced to be in PWM mode at the external clock frequency. The LM2614 synchronizes to the rising edge of the external clock. www.national.com 4 LM2614 Typical Performance Characteristics LM2614ATL, Circuit of Figure 4, VIN = 3.6V, TA = 25C, unless otherwise noted. Shutdown Quiescent Current vs Temperature (Circuit in Figure 3) Quiescent Supply Current vs Supply Voltage 20036708 20036722 Output Voltage vs Supply Voltage (VOUT = 1.5V, PWM MODE) Output Voltage vs Supply Voltage (VOUT = 1.0V, PWM MODE) 20036724 20036709 Output Voltage vs Output Current (VOUT = 1.5V, PWM MODE) Output Voltage vs Output Current (VOUT = 1.0V, PWM MODE) 20036710 20036711 5 www.national.com LM2614 Typical Performance Characteristics LM2614ATL, Circuit of Figure 4, VIN = 3.6V, TA = 25C, unless otherwise noted. (Continued) Output Voltage vs Output Current (VOUT = 3.6V, PWM MODE) Dropout Voltage vs Output Current (VOUT = 3.6V, PWM MODE) 20036732 20036712 Switching Frequency vs Temperature (Circuit in Figure 3, PWM MODE) Feedback Bias Current vs Temperature (Circuit in Figure 3) 20036723 20036731 Efficiency vs Output Current (VOUT = 1.0V, PWM MODE, with Diode) Efficiency vs Output Current (VOUT = 1.0V, PWM MODE) 20036713 www.national.com 20036714 6 LM2614 Typical Performance Characteristics LM2614ATL, Circuit of Figure 4, VIN = 3.6V, TA = 25C, unless otherwise noted. (Continued) Efficiency vs Output Current (VOUT = 1.5V, PWM MODE) Efficiency vs Output Current (VOUT = 1.5V, PWM MODE, with Diode) 20036715 20036716 Efficiency vs Output Current (VOUT = 3.6V, PWM MODE, with Diode) Efficiency vs Output Current (VOUT = 3.6V, PWM MODE) 20036717 20036718 7 www.national.com LM2614 Typical Performance Characteristics LM2614ATL, Circuit of Figure 4, VIN = 3.6V, TA = 25C, unless otherwise noted. (Continued) Efficiency vs Output Voltage (PWM MODE, with Diode) 20036730 3.9V input. The efficiency can be further increased by using a schottky diode like MBRM120 as shown in Figure 4. PWM mode quiescent current is 600A typ. The output voltage is dynamically programmable from 1.0V to 3.6V by adjusting the voltage on the VCON at the external feedback resistors. This ensures longer battery life by being able to change the PA supply voltage dynamically depending on its transmitting power. Additional features include soft-start, current overload protection, over voltage protection and thermal shutdown protection. The LM2614 is constructed using a chip-scale 10-pin thin micro SMD package. This package offers the smallest possible size, for space-critical applications such as cell phones, where board area is an important design consideration. Use of a high switching frequency (600kHz) reduces the size of external components. Board area required for implementation is only 0.58in2 (375mm2). Use of a micro-SMD package requires special design considerations for implementation. (See Micro SMD Package Assembly and Use in the Application Information section.) Its fine bump-pitch requires careful board design and precision assembly equipment. Device Information The LM2614 is a simple, step-down DC-DC converter optimized for powering RF power amplifiers (PAs) in mobile phones, portable communicators, and similar battery powered RF devices. It is designed to allow the RF PA to operate at maximum efficiency over a wide range of power levels from a single LiION battery cell. It is based on a current-mode buck architecture, with synchronous rectification in PWM mode for high efficiency. It is designed for a maximum load capability of 400mA (300mA for B grade) in PWM mode. Maximum load range may vary from this depending on input voltage, output voltage and the inductor chosen. The device has all three of the pin-selectable operating modes required for powering RF PAs in mobile phones and other sophisticated portable devices with complex power management needs. Fixed-frequency PWM operation offers full output current capability at high efficiency while minimizing interference with sensitive IF and data acquisition circuits. During standby operation, hysteretic PFM mode reduces quiescent current to 160A typ. to maximize battery life. Shutdown mode turns the device off and reduces battery consumption to 0.02A (typ). DC PWM mode feedback voltage precision is 1%. Efficiency is typically 96% for a 200mA load with 3.6V output, www.national.com 8 LM2614 Device Information (Continued) 20036706 FIGURE 4. Typical Operating Circuit transferred back into the circuit and depleted, the inductor current ramps down with a slope of VOUT/L. If the inductor current reaches zero before the next cycle, the synchronous rectifier is turned off to prevent current reversal. The output filter capacitor stores charge when the inductor current is high, and releases it when low, smoothing the voltage across the load. The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and synchronous rectifier at SW to a low-pass filter formed by the inductor and output filter capacitor. The output voltage is equal to the average voltage at the SW pin. CIRCUIT OPERATION Referring to Figure 4, Figure 5, Figure 6 and Figure 7, the LM2614 operates as follows. During the first part of each switching cycle, the control block in the LM2614 turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with a slope of (VIN-VOUT)/L, by storing energy in a magnetic field. During the second part of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET synchronous rectifier on. In response, the inductor's magnetic field collapses, generating a voltage that forces current from ground through the synchronous rectifier to the output filter capacitor and load. As the stored energy is 20036707 FIGURE 5. Simplified Functional Diagram 9 www.national.com LM2614 Device Information (Continued) PFM Mode Switching Waveform PWM OPERATION While in PWM (Pulse Width Modulation) mode, the output voltage is regulated by switching at a constant frequency and then modulating the energy per cycle to control power to the load. Energy per cycle is set by modulating the PFET switch on-time pulse-width to control the peak inductor current. This is done by comparing the signal from the current-sense amplifier with a slope compensated error signal from the voltage-feedback error amplifier. At the beginning of each cycle, the clock turns on the PFET switch, causing the inductor current to ramp up. When the current sense signal ramps past the error amplifier signal, the PWM comparator turns off the PFET switch and turns on the NFET synchronous rectifier, ending the first part of the cycle. If an increase in load pulls the output voltage down, the error amplifier output increases, which allows the inductor current to ramp higher before the comparator turns off the PFET. This increases the average current sent to the output and adjusts for the increase in the load. 20036726 A: Inductor Current, 500mA/div B: SW Pin, 2V/div C: VOUT, 50mV/div, AC Coupled Before going to the PWM comparator, the error signal is summed with a slope compensation ramp from the oscillator for stability of the current feedback loop. During the second part of the cycle, a zero crossing detector turns off the NFET synchronous rectifier if the inductor current ramps to zero. The minimum on time of the PFET in PWM mode is about 200ns. FIGURE 7. PFM OPERATION Connecting the SYNC/MODE to SGND sets the LM2614 to hysteretic PFM operation. While in PFM (Pulse Frequency Modulation) mode, the output voltage is regulated by switching with a discrete energy per cycle and then modulating the cycle rate, or frequency, to control power to the load. This is done by using an error comparator to sense the output voltage. The device waits as the load discharges the output filter capacitor, until the output voltage drops below the lower threshold of the PFM error-comparator. Then the device initiates a cycle by turning on the PFET switch. This allows current to flow from the input, through the inductor to the output, charging the output filter capacitor. The PFET is turned off when the output voltage rises above the regulation threshold of the PFM error comparator. Thus, the output voltage ripple in PFM mode is proportional to the hysteresis of the error comparator. In PFM mode, the device only switches as needed to service the load. This lowers current consumption by reducing power consumed during the switching action in the circuit, due to transition losses in the internal MOSFETs, gate drive currents, eddy current losses in the inductor, etc. It also improves light-load voltage regulation. During the second half of the cycle, the intrinsic body diode of the NFET synchronous rectifier conducts until the inductor current ramps to zero. PWM Mode Switching Waveform 20036725 A: Inductor Current, 500mA/div B: SW Pin, 2V/div C: VOUT, 10mV/div, AC Coupled FIGURE 6. OPERATING MODE SELECTION The LM2614 is designed for digital control of the operating modes by the system controller. This prevents the spurious switch over from low-noise PWM mode between transmission intervals in mobile phone applications that can occur in other products. The SYNC/MODE digital input pin is used to select the operating mode. Setting SYNC/MODE high (above 1.3V) selects 600kHz current-mode PWM operation. PWM mode is optimized for low-noise, high-power operation for use when the load is active. Setting SYNC/MODE low (below 0.4V) selects hysteretic voltage-mode PFM operation. PFM mode is optimized for reducing power consumption and www.national.com 10 EN should be set low to turn off the LM2614 during system power-up and undervoltage conditions when the supply is less than the 2.8V minimum operating voltage. The LM2614 is designed for compact portable applications, such as mobile phones. In such applications, the system controller determines power supply sequencing. Although the LM2614 is typically well behaved at low input voltages, this is not guaranteed. (Continued) extending battery life when the load is in a low-power standby mode. In PFM mode, quiescent current into the VDD pin is 160A typ. In contrast, PWM mode VDD-pin quiescent current is 600A typ. PWM operation is intended for use with loads of 50mA or more, when low noise operation is desired. Below 100mA, PFM operation can be used to allow precise regulation, and reduced current consumption. However, it should be noted that for PA applications the PFM mode need not be used as output voltage slew rates are of more concern to the system designer. The LM2614 has an over-voltage feature that prevents the output voltage from rising too high, when the device is left in PWM mode under low-load conditions. See Overvoltage Protection, for more information. Switch modes with the SYNC/MODE pin, using a signal with a slew rate faster than 5V/100s. Use a comparator, Schmitt trigger or logic gate to drive the SYNC/MODE pin. Do not leave the pin floating or allow it to linger between thresholds. These measures will prevent output voltage errors in response to an indeterminate logic state. The LM2614 switches on each rising edge of SYNC. Ensure a minimum load to keep the output voltage in regulation when switching modes frequently. INTERNAL SYNCHRONOUS RECTIFICATION While in PWM mode, the LM2614 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. The internal NFET synchronous rectifier is turned on during the inductor current down slope during the second part of each cycle. The synchronous rectifier is turned off prior to the next cycle, or when the inductor current ramps to zero at light loads. The NFET is designed to conduct through its intrinsic body diode during transient intervals before it turns on, eliminating the need for an external diode. CURRENT LIMITING A current limit feature allows the LM2614 to protect itself and external components during overload conditions. In PWM mode cycle-by-cycle current limit is normally used. If an excessive load pulls the voltage at the feedback pin down to approximately 0.7V, then the device switches to a timed current limit mode. In timed current limit mode the internal P-FET switch is turned off after the current comparator trips and the beginning of the next cycle is inhibited for 2.5s to force the instantaneous inductor current to ramp down to a safe value. Timed current limit mode prevents the loss of current control seen in some products when the voltage at the feedback pin is pulled low in serious overload conditions. FREQUENCY SYNCHRONIZATION The SYNC/MODE input can also be used for frequency synchronization. During synchronization, the LM2614 initiates cycles on the rising edge of the clock. When synchronized to an external clock, it operates in PWM mode. The device can synchronize to a 50% duty-cycle clock over frequencies from 500kHz to 1MHz. If a different duty cycle is used other than 50% the range for acceptable duty cycles are 30% to 70%. Use the following waveform and duty cycle guidelines when applying an external clock to the SYNC/MODE pin. Clock under/overshoot should be less than 100mV below GND or above VDD. When applying noisy clock signals, especially sharp edged signals from a long cable during evaluation, terminate the cable at its characteristic impedance and add an RC filter to the SYNC pin, if necessary, to soften the slew rate and over/undershoot. Note that sharp edged signals from a pulse or function generator can develop under/overshoot as high as 10V at the end of an improperly terminated cable. DYNAMICALLY ADJUSTABLE OUTPUT VOLTAGE The LM2614 can be used to provide dynamically adjustable output voltage by using external feedback resistors. The output can be varied from 1.0V to 3.6V in less than 30s by using an analog control signal (VCON) at the external feedback resistors. This feature is useful in PA applications where peak power is needed only when the handset is far away from the base station or when data is being transmitted. In other instances the transmitting power can be reduced and hence the supply voltage to the PA can be reduced helping maintain longer battery life. See Setting the Output Voltage in the Application Information section for further details. In dropout conditions the output voltage is VIN - IOUT (Rdc + RDSON (P)) where Rdc is the series resistance of the inductor and RDSON (P) is the on resistance of the PFET. OVERVOLTAGE PROTECTION The LM2614 has an over-voltage comparator that prevents the output voltage from rising too high when the device is left in PWM mode under low-load conditions. When the output voltage rises by about 100mV (Figure 3) over its regulation threshold, the OVP comparator inhibits PWM operation to skip pulses until the output voltage returns to the regulation threshold. When resistor dividers are used the OVP threshold at the output will be the value of the threshold at the feedback pin times the resistor divider ratio. In over voltage protection, output voltage and ripple will increase. SHUTDOWN MODE Setting the EN digital input pin low ( < 0.4V) places the LM2614 in a 0.02A (typ) shutdown mode. During shutdown, the PFET switch, NFET synchronous rectifier, reference, control and bias circuitry of the LM2614 are turned off. Setting EN high enables normal operation. While turning on, soft start is activated. 11 www.national.com LM2614 Device Information LM2614 Device Information (Continued) Load Transient Response (Circuit in Figure 3) VCON Transient Response (Circuit in Figure 4) 20036727 20036719 FIGURE 10. FIGURE 8. Line Transient Response (Circuit in Figure 3) VCON Transient Response in Dropout (Circuit in Figure 4) 20036728 20036720 FIGURE 11. FIGURE 9. SOFT-START The LM2614 has soft start to reduce current inrush during power-up and startup. This reduces stress on the LM2614 and external components. It also reduces startup transients on the power source. Soft start is implemented by ramping up the reference input to the error amplifier of the LM2614 to gradually increase the output voltage. THERMAL SHUTDOWN PROTECTION The LM2614 has a thermal shutdown protection function to protect itself from short-term misuse and overload conditions. When the junction temperature exceeds 150C the device turns off the output stage and when the temperature drops below 130C it initiates a soft start cycle. Prolonged operation in thermal shutdown conditions may damage the device and is considered bad practice. www.national.com 12 SETTING THE OUTPUT VOLTAGE The LM2614 can be used with external feedback resistors and an analog signal to vary the output voltage. Select an output voltage from 1.0V to 3.6V by setting the voltage on the VCON as directed in Table 1. EXTERNAL COMPENSATION The LM2614 uses external components connected to the EANEG and EAOUT pins to compensate the regulator (Figure 4). Typically, all that is required is a series connection of one capacitor (C4) and one resistor (R3). A capacitor (C5) can be connected across the EANEG and EAOUT pins to improve the noise immunity of the loop. C5 reacts with R3 to give a high frequency pole. C4 reacts with the high open loop gain of the error amplifier and the resistance at the EANEG pin to create the dominant pole for the system, while R3 and C4 react to create a zero in the frequency response. The pole rolls off the loop gain, to give a bandwidth somewhere between 10kHz and 50kHz, this avoids a 100kHz parasitic pole contributed by the current mode controller. Typical values in the 220pF to 1nF (C4) range are recommended to create a pole on the order of 10Hz or less. TABLE 1. Output Voltage Selection VCON (V) VOUT (V) VCON = 0V VFB (1+R1/R2) VCON > 0V VFB (1+R1/R2)-VCON (R1/R2) Refer to Figure 12 for the relation between VOUT and VCON. VOUT vs VCON (Circuit in Figure 4) The next dominant pole in the system is formed by the output capacitance (C2) and the parallel combination of the load resistance and the effective output resistance of the regulator. This combined resistance (Ro) is dominated by the small signal output resistance, which is typically in the range of 3 to 15. The exact value of this resistance, and therefore this load pole depends on the steady state duty cycle and the internal ramp value. Ideally we want the zero formed by R3 and C4 to cancel this load pole, such that R3=RoC2/C4. Due to the large variation in Ro, this ideal case can only be achieved at one operating condition. Therefore a compromise of about 5 for Ro should be used to determine a starting value for R3. This value can then be optimized on the bench to give the best transient response to load changes and changes in VCON, under all conditions. Typical values are 10pF for C5 and 220pF to 470pF for C4, to ensure good response from dropout conditions to VOUT(min). 20036721 INDUCTOR SELECTION Use a 10H inductor with saturation current rating higher than the peak current rating of the device. The inductor's resistance should be less than 0.3 for good efficiency. Table 2 lists suggested inductors and suppliers. FIGURE 12. When the control voltage is between 1.85V and 0V, the output voltage will vary in a monotonic fashion with respect TABLE 2. Suggested Inductors and Their Suppliers Part Number Vendor Phone FAX 847-639-1469 DO1608C-103 Coilcraft 847-639-6400 P1174.103T Pulse 858-674-8100 858-674-8262 ELL6RH100M Panasonic 714-373-7366 714-373-7323 CDRH5D18-100 Sumida 847-956-0666 847-956-0702 P0770.103T Pulse 858-674-8100 858-674-8262 For low-cost applications, an unshielded inductor is suggested. For noise critical applications, a toroidal or shielded inductor should be used. A good practice is to lay out the board with footprints accommodating both types for design flexibility. This allows substitution of a low-noise shielded inductor, in the event that noise from low-cost unshielded models is unacceptable. The saturation current rating is the current level beyond which an inductor loses its inductance. Different manufacturers specify the saturation current rating differently. Some specify saturation current point to be when inductor value falls 30% from its original value, others specify 10%. It is always better to look at the inductance versus current curve and make sure the inductor value doesn't fall below 30% at the peak current rating of the LM2614. Beyond this rating, the inductor loses its ability to limit current through the PWM switch to a ramp. This can cause poor efficiency, regulation errors or stress to DC-DC converters like the LM2614. Saturation occurs when the magnetic flux density from current through the windings of the inductor exceeds what the inductor's core material can support with a corresponding magnetic field. 13 www.national.com LM2614 to the voltage on the control pin as per the equation in Table 1. Select the value of R2 to allow at least 100 times the feedback pin bias current to flow through it. Application Information LM2614 Application Information and/or increased tolerance to heavy load transients. A 10F ceramic output capacitor can be used in applications where the worst case load transient step is less than 200mA. Table 3 lists suggested capacitors and suppliers. The input filter capacitor supplies current to the PFET switch of the LM2614 in the first part of each cycle and reduces voltage ripple imposed on the input power source. The output filter capacitor smoothes out current flow from the inductor to the load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR to perform these functions. Parallel combinations of smaller value ceramic capacitors can also be used on the output as long as the combined value is at least 4.7F for the application circuit in Figure 1. The ESR, or equivalent series resistance, of the filter capacitors is a major factor in voltage ripple. (Continued) CAPACITOR SELECTION Use a 4.7F or 10F ceramic input capacitor. A 10F ceramic input capacitor is recommended if the PA represents a load < 14. Use a 4.7F ceramic output capacitor for getting faster slew rates for output voltages from VOUT (min) to VOUT (max). Use X7R or X5R types, do not use Y5V. The rise time for the voltage from VOUT (min) to VOUT (max) depends on the slew rate of the error amp, switch peak current limit and the value of the output capacitor. The time for the output to change from VOUT (max) to VOUT (min) depends on RLOAD and COUT. Use of tantalum capacitors is not recommended. Ceramic capacitors provide an optimal balance between small size, cost, reliability and performance for cell phones and similar applications. A 22F ceramic output capacitor can be used in applications requiring fixed output voltages TABLE 3. Suggested Capacitors and Their Suppliers Model Type Vendor Phone FAX C1, C2 (Input or Output Filter Capacitor) JMK212BJ475MG Ceramic Taiyo-Yuden 847-925-0888 847-925-0899 LMK316BJ475ML Ceramic Taiyo-Yuden 847-925-0888 847-925-0899 C2012X5R0J475K Ceramic TDK 847-803-6100 847-803-6296 JMK325BJ226MM Ceramic Taiyo-Yuden 847-925-0888 847-925-0899 JMK212BJ106MG Ceramic Taiyo-Yuden 847-925-0888 847-925-0899 micro SMD PACKAGE ASSEMBLY AND USE Use of the micro SMD package requires specialized board layout, precision mounting and careful reflow techniques, as detailed in National Semiconductor Application Note AN-1112. Refer to the section Surface Mount Technology (SMT) Assembly Considerations. For best results in assembly, alignment ordinals on the PC board should be used to facilitate placement of the device. The pad style used with micro SMD package must be the NSMD (non-solder mask defined) type. This means that the solder-mask opening is larger than the pad size. This prevents a lip that otherwise forms if the solder-mask and pad overlap, from holding the device off the surface of the board and interfering with mounting. See Application Note AN-1112 for specific instructions how to do this. The 10-Bump package used for the LM2614 has 300 micron solder balls and requires 10.82mil pads for mounting on the circuit board. The trace to each pad should enter the pad with a 90 entry angle to prevent debris from being caught in deep corners. Initially, the trace to each pad should be 6-7mil wide, for a section approximately 6mil long, as a thermal relief. Then each trace should neck up or down to its optimal width. The important criterion is symmetry. This ensures the solder bumps on the LM2614 reflow evenly and that the device solders level to the board. In particular, special attention must be paid to the pads for bumps D3-B3. Because PGND and PVIN are typically connected to large copper planes, inadequate thermal reliefs can result in late or inadequate reflow of these bumps. The micro SMD package is optimized for the smallest possible size in applications with red or infrared opaque cases. Because the micro SMD package lacks the plastic encapsulation characteristic of larger devices, it is vulnerable to light. Backside metalization and/or epoxy coating, along with front-side shading by the printed circuit board, reduce this sensitivity. www.national.com BOARD LAYOUT CONSIDERATIONS PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to the DC-DC converter IC, resulting in poor regulation or instability. Poor layout can also result in reflow problems leading to poor solder joints between the micro SMD package and board pads. Poor solder joints can result in erratic or degraded performance. Good layout for the LM2614 can be implemented by following a few simple design rules. 1. Place the LM2614 on 10.82 mil (10.82/1000 in.) pads. As a thermal relief, connect to each pad with a 7 mil wide, approximately 7 mil long traces, and then incrementally increase each trace to its optimal width. The important criterion is symmetry to ensure the solder bumps on the LM2614 reflow evenly (see micro SMD Package Assembly and Use). 2. Place the LM2614, inductor and filter capacitors close together and make the traces short. The traces between these components carry relatively high switching currents and act as antennas. Following this rule reduces radiated noise. Place the capacitors and inductor within 0.2 in. (5 mm) of the LM2614. 14 reduces voltage errors caused by resistive losses across the traces. (Continued) 3. Arrange the components so that the switching current loops curl in the same direction. During the first half of each cycle, current flows from the input filter capacitor, through the LM2614 and inductor to the output filter capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled up from ground, through the LM2614 by the inductor, to the output filter capacitor and then back through ground, forming a second current loop. Routing these loops so the current curls in the same direction prevents magnetic field reversal between the two half-cycles and reduces radiated noise. 4. Connect the ground pins of the LM2614, and filter capacitors together using generous component-side copper fill as a pseudo-ground plane. Then, connect this to the ground-plane (if one is used) with several vias. This reduces ground-plane noise by preventing the switching currents from circulating through the ground plane. It also reduces ground bounce at the LM2614 by giving it a low-impedance ground connection. 6. Route noise sensitive traces, such as the voltage feedback path, away from noisy traces between the power components. The voltage feedback trace must remain close to the LM2614 circuit and should be routed directly from VOUT at the output capacitor and should be routed opposite to noise components. This reduces EMI radiated onto the DC-DC converter's own voltage feedback trace. 7. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks and other noisy circuitry. Interference with noise-sensitive circuitry in the system can be reduced through distance. In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board, arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a metal pan and power to it is post-regulated to reduce conducted noise, using low-dropout linear regulators. 5. Use wide traces between the power components and for power connections to the DC-DC converter circuit. This 15 www.national.com LM2614 Application Information LM2614 400mA Sub-Miniature Adjustable DC-DC Converter Optimized for RF Power Amplifiers Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211. VARIATION BD. 10-Bump micro SMD Package NS Package Number TLP106WA The dimensions for X1, X2 and X3 are as given: X1 = 2.250 0.030 mm X2 = 2.504 0.030 mm X3 = 0.600 0.075 mm LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.