TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
MULTIPLE (QUAD) NPN SILICON DUAL IN-LINE
AND FLATPACK SWITCHING TRANSISTOR
Qualified per MIL-PRF-19500/559
T4-LDS-0177 Rev. 1 (101229) Page 1 of 7
DEVICES LEVELS
2N6989 2N6989U JAN
2N6990 JANTX
JANTXV
JANS
ABSOLUTE MAXIMUM RATI NG S (TC = +25°C unless otherwise noted)
Parameters / Test Conditions Symbol Value Unit
Collector-Emitter Voltage (3) V
CEO 50 Vdc
Collector-Base Voltage (3) V
CBO 75 Vdc
Emitter-Base Voltage (3) V
EBO 6.0 Vdc
Collector Current (3) I
C 800 mAdc
Total Power Dissipation
@ TA = +25°C
2N6989 (2)
2N6989U (2)
2N6990 (2)
PD
1.5
1.0
1.0
W
Operating & Storage Junction Temperature Range Top, Tstg -65 to +200 °C
Note:
1. Maximum voltage between transistors shall be 500Vdc.
2. For derating, see figures 6, 7, 8 and 9. Ratings apply to total package.
3. For thermal impedance curves, see figures 10, 11, 12 and 13.
4. Ratings apply to each transistor in the array.
ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted)
Parameters / Test Conditions Symbol Min. Max. Unit
OFF CHARACTERTICS
Collector-Emitter Breakdown Voltage
IC = 10mAdc V(BR)CEO 50 Vdc
Collector-Base Cutoff Current
VCB = 60Vdc
VCB = 75Vdc
VCB = 60Vdc, TA = +150°C
ICBO
10
10
10
ηAdc
μAdc
μAdc
Emitter-Base Cutoff Current
VEB = 4.0Vdc
VEB = 6.0Vdc
IEBO 10
10 μAdc
ηAdc
TO-116 – 2N6989
20 PIN LEADLESS
2N6989U
14 PIN FLAT PACK
2N6990
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 2 of 7
ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted)
Parameters / Test Conditions Symbol Min. Max. Unit
ON CHARACTERISTICS (4)
Forward-Current Transfer Ratio
hFE
IC = 0.1mAdc, VCE = 10Vdc 50
IC = 1.0mAdc, VCE = 10Vdc 75 325
IC = 10mAdc, VCE = 10Vdc 100
IC = 150mAdc, VCE = 10Vdc 100 300
IC = 500mAdc, VCE = 10Vdc 30
IC = 10mAdc, VCE = 10Vdc, TA = -55°C 35
Collector-Emitter Saturation Voltage
VCE(sat)
Vdc
IC = 150mAdc, IB = 15mAdc
IC = 500mAdc, IB = 50mAdc
0.3
1.0
Base-Emitter Saturation Voltage
VBE(sat)
Vdc
IC = 150mAdc, IB = 15mAdc
IC = 500mAdc, IB = 50mAdc
0.6 1.2
2.0
DYNAMIC CHARACTERISTICS
Parameters / Test Conditions Symbol Min. Max. Unit
Magnitude of Small–Signal Short-Circuit Forward Current Transfer Ratio
|hfe|
IC = 20mAdc, VCE = 10Vdc, f = 100MHz 2.5 8.0
Forward current Transfer Ratio
hfe 50
IC = 1.0mAdc, VCE = 10Vdc, f = 1.0kHz
Output Capacitance
Cobo 8.0 pF
VCB = 10Vdc, IE = 0, 100kHz f 1.0MHz
Input Capacitance
Cibo 25 pF
VEB = 0.5Vdc, IE = 0, 100kHz f 1.0MHz
SWITCHING CHARACTERISTICS
Parameters / Test Conditions Symbol Min. Max. Unit
Turn-On Time
ton
SEE FIGURE 14 / MIL-PRF-19500/559 35
ηs
Turn-Off Time
toff
ηs
SEE FIGURE 15 / MIL-PRF-19500/559 300
(4) Pulse Test: Pulse Width = 300μs, Duty Cycle 2.0%.
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 3 of 7
PACKAGE DIMENSIONS
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 4 of 7
Dimensions
Dimensions
Symbol Inches Millimeters Notes
Symbol Inches Millimeters Notes
Min Max Min Max
Min Max Min Max
BH .200 5.08 LS .100 BSC 2.54 BSC 7, 11
LW .014 .023 0.36 0.58 10 LL .125 .200 3.18 5.08
LW1 .030 .070 0.76 1.78 4, 10 LL1 .150 3.81
LT .008 .015 0.20 0.38 10 LO .005 0.13 8
BL .785 19.94 6 LO1 .098 2.49 8
BW .220 .310 5.59 7.87 6 LO2 .015 .060 0.38 1.52 5
BW1 .290 .320 7.37 8.13 9 α 0° 15° 0° 15°
NOTES:
1 Dimension are in inches.
2 Millimeters are given for general information only.
3 Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used as a pin one identification mark.
4 The minimum limit for dimension LW1 may be .023 inch (0.58 mm) for leads number 1, 7, 8 and 14 only.
5 Dimension LO2 shall be measured from the seating plane to the base plane.
6 This dimension allows for off-center lid, meniscus, and glass overrun.
7 The basic pin spacing is .100 inch (2.54 mm) between centerlines. Each pin centerline shall be located within ±.010 inch (0.25
mm) of its exact longitudinal position relative to pins 1 and 14.
8 Applies to all four corners (leads number 1, 7, 8 and 14).
9 Lead center when α is 0 degrees. BW1 shall be measured at the centerline of the leads.
10 All leads.
11 Twelve spaces.
12 No organic or polymeric materials shall be molded to the bottom of the package to cover the leads.
13 In accordance with ASME Y14.5M, diameters are equivalent to φx symbology.
FIGURE 1. Physical Dimension and Configuration for type 2N6989
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 5 of 7
PACKAGE DIMENSIONS
Dimensions
Dimensions
Symbol Inches Millimeters Notes
Symbol Inches Millimeters Notes
Min Max Min Max
Min Max Min Max
CH .030 .115 0.76 2.92 BW3 .030 0.76
LW .010 .019 0.25 0.48 7 LS .050 BSC 1.27 BSC 6, 8
TL .008 .015 0.20 0.38 12 LT .003 .006 0.076 0.152 7
BL .280 7.11 5 LL .250 .370 6.35 9.40
BW .240 .260 6.10 6.60 LD2 .005 .040 0.13 1.02 4
LU .290 7.37 5 LO .005 0.13 9, 10
BW2 .125 3.18 LO3 .004 13
α 30° 90° 30° 90° 14
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 6 of 7
NOTES:
1 Dimension are in inches.
2 Millimeters are given for general information only.
3 Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used as a pin one identification mark. Alternatively, a tab (dine TL)
may be used to identify pin one.
4 Dimension LD2 shall be measured at the point of exit of the lead from the body.
5 This dimension allows for off-center lid, meniscus, and glass overrun.
6 The basic pin spacing is .050 inch (1.27 mm) between centerlines. Each pin centerline shall be located within ±.005 inch (0.13
mm) of its exact longitudinal position relative to pins 1 and 14.
7 All leads: Increase maximum limit by .003 inch (0.08 mm) measured at the center of the flat when the lead finish is solder.
8 Twelve spaces.
9 Applies to all four corners (leads number 2, 6, 9 and 13).
10 Dimension LO may be .000 inch (0.00 mm if leads number 2, 6, 9, and 13) bend toward the cavity of the package within one
lead width from the point of entry of the lead into the body or if the leads are brazed to the metalized ceramic body.
11 No organic or polymeric materials shall be molded to the bottom of the package to cover the leads.
12 Optional, see note 1. If a pin one identification mark is used in addition to this tab, the minimum limit of dimension TL does
not apply.
13 Applies to leads number 1, 7, 8, and 14.
14 Lead configuration is optional within dimension BW except dimensions LW and LT apply.
15 In accordance with ASME Y14.5M, diameters are eqivalent to φx symbology.
16 Pins 1, 7, 8, and 14 are collectors.
17 Pin 2, 6, 9, and 13 are bases.
18 Pin 3, 5, 10, and 12 are emitters.
19 Pins 4 and 11 are no contacts.
FIGURE 2. Physical dimensions for type 2N6990
FIGURE 3. Schematic and terminal connections for types 2N6989 & 2N6990
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland.
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0177 Rev. 1 (101229) Page 7 of 7
PACKAGE DIMENSIONS
NOTES:
1 Dimensions are in inches.
2 Millimeters are given for general information only.
3 Unless otherwise specified, tolerance is ±.005 inch (0.13 mm).
4 In accordance with ASME Y14.5M, diameters are equivalent to
φx symbology.
FIGURE 4. Physical demension for type 2N6989U
Dimensions
Symbol Inches Millimeters
Min Max Min Max
A .073 .085 1.85 2.16
A1 .063 .075 1.60 1.91
D .345 .355 8.76 9.02
D1 .195 .205 4.95 5.21
D2 .050 TYP 1.27 TYP
D3 .070 .080 1.78 2.03
E .025 REF 0.64 REF
L1 .050 REF
for pins 2 through 20
1.27 REF
for pins 2 through 20
L2 .080 .090 2.03 2.29
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Microsemi:
Jan2N6989 2N6989 2N6990 Jantxv2N6989 2N6989U Jan2N6990 Jantx2N6990 JANTXV2N6990
Jantxv2N6989U