DEMO CIRCUIT 1030 LTC3218 QUICK START GUIDE LTC3218 400mA Single Wire Camera LED Charge Pump DESCRIPTION WARNING! Do not look directly at operating LED. This circuit produces light that can damage eyes. Demonstration circuit 1030 is a 400mA Single Wire Camera LED Charge Pump featuring the LTC3218. This circuit will provide 50mA of continuous torch current or a flash current at 300mA or 400mA. The LTC3218 has a built-in 2-second flash timer to protect the LED in case of faults during flash mode. The LTC3218 is a low-noise, high current charge pump capable of flashing a Camera LED up to 400mA. The LTC3218 design requires only three capacitors and one program resistor to provide a complete Camera Driver circuit with one torch and two flash current settings. A second programming resistor may be used to provide a wider range of LED torch and flash current settings. Pressing the ENT push button, SW1, enables torch mode. Pressing the ENF push button, SW2, enables flash mode. Pressing both ENT and ENF push buttons enables the high intensity flash mode. Pulse generator(s) may be connected to the ENF and/or ENT terminals to better control the pulse timing for evaluation of flash and current performance. Built-in soft-start circuit prevents excessive inrush currents during start up. The LED output current is regulated using an internal high side resistor allowing the LED cathode to be connected directly to ground. The Charge Pump Output (CPO) voltage is monitored and automatically switches to 2X mode only when a dropout has been detected to optimize efficiency. Refer to the LTC3218 datasheet for more information on this device. Design files for this circuit board are available. Call the LTC factory. L, LTC, LTM, LT, are registered trademarks of Linear Technology Corporation. Other product names may be trademarks of the companies that manufacture the products. PERFORMANCE SUMMARY Specifications are at TA = 25C PARAMETER VIN Input Supply Range IVIN Shutdown Current IVIN Operating Current ILED Torch Current ILED Flash Current ILED High Flash Current ILED Dropout Voltage (VILED) Minimum LED Forward Voltage Charge Pump Output Clamp Voltage CONDITIONS MIN 2.9 ENF = ENT = LOW, VCPO = 0V ICPO = 0mA, 1X Mode ICPO = 0mA, 2X Mode ENT = HIGH, ENF = LOW ENT = LOW, ENF = HIGH ENT = HIGH, ENF = HIGH Mode Switching Threshold, VCPO - VILED, ILED = 100mA ILED = 50mA TYP 1.1 980 6.7 45 290 390 7 2.2 5.3 MAX 4.5 3 UNITS V A A mA mA mA mA mV V V 1 LTC3218 QUICK START PROCEDURE Demonstration circuit 1030 is easy to set up to evaluate the performance of the LTC3218. Refer to Figure 1 for proper measurement equipment setup and follow the procedure below: NOTE. When measuring the input or output voltage ripple, care must be taken to avoid a long ground lead on the oscilloscope probe. Measure the input or output voltage ripple by touching the probe tip directly across the Vin or Vout and GND terminals. See Figure 2 for proper scope probe technique. 1. With power off, connect a variable +5V, 1A input power supply in series with an ammeter to VIN and GND. For best stability and noise performance, use the shortest leads possible between the board and the supply. Capacitor C4 has been placed on the board to assist in offsetting the effects of long power supply leads. 2. Turn on the power at the input and set the supply to 4.5V. NOTE. Make sure that the input voltage does not exceed 6V. 2 3. Press and hold the ENT push button, SW1, and observe that the LED illuminates. 4. Press and hold the ENF push button, SW2, and observe the LED illuminates brightly for two seconds. The two-second timer turns off the LED. 5. Press and hold both the ENT and ENF push buttons simultaneously. Observe that the LED illuminates even brighter for two seconds. The two-second timer again turns off the LED. 6. Try steps 3 through 5 with VIN Voltages of 3.6V and 3.0V. Observe when the device drops out, the charge pump automatically switches to 2X mode and the input current doubles. NOTE. The ENT and ENF push buttons do not have any de-bounce circuitry and may cause the part to switch to 2X mode. For better control of the ENT and ENF pins, connect a pulse generator to the ENT and ENF terminals. Make sure these terminals do not exceed VIN + 0.3V. LTC3218 Figure 1. Proper Measurement Equipment Setup GND VIN Figure 2. Measuring Input or Output Ripple 3 LTC3218 4 LTC3218 5