CY7C1223H-133AXC - Cypress Semiconductor

2-Mbit (128K x 18) Pipelined DCD Sync SRAM

CY7C1223H

Cypress Semiconductor Corporation • 198 Champion Court • San Jose,CA 95134-1709 • 408-943-2600

Document #: 38-05674 Rev. *B Revised February 6, 2006

Features

• Registered inp uts and outputs for pipelined op eration

• Optimal for performance (Double-Cycle deselect)

— Depth expansion without wait state

• 128K × 18-bit common I/O arch itecture

• 3.3V core power supply

• 3.3V/2.5V I/O supply

• Fast clock-to-output time

— 3.5 ns (for 166-MHz device)

— 4.0 ns (for 133-MHz device)

• Provide high-performance 3-1-1-1 access rate

• User-selectable burst counter supporting Intel®

Pentium® interleaved or linear burst sequences

• Separate processor and controller address strobes

• Synchronous self-timed write

• Asynchr onous Output Enable

• Offered in JEDEC-standard lead-free 100-pin TQFP

package

• “ZZ” Sleep Mode option

Functional Description[1]

The CY7C1223H SRAM integrates 128K x 18 SRAM cells with

advanced synchronous peripheral circuitry and a two-bit

counter for internal burst operation. All synchronous inputs are

gated by registers controlled by a positive-edge-triggered

Clock Input (CLK). The synchronous inputs include all

addresses, all data inputs, address-pipelining Chip Enable

(CE1), depth-expansion Chip Enables (CE2 and CE3), Burst

Control inputs (ADSC, ADSP, and ADV), Write Enables

(BW[A:B] and BWE), and Global Write (GW). Asynchronous

inputs include the Output Enable (OE) and the ZZ pin.

Addresses and chip enables are registered at rising edge of

clock when either Address Strobe Processor (ADSP) or

Address Strobe Controller (ADSC) are active. Subsequent

burst addresses can be internally generated as controlled by

the Advance pin (ADV).

Address, data inputs, and write controls are registered on-chip

to initiate a self-timed Write cycle.This part supports Byte Write

operations (see Pin Descriptions and Truth Table for further

details). Write cycles can be one to two bytes wide as

controlled by the byte write control inputs. GW active LOW

causes all bytes to be written. This device incorporates an

additional pipelined enable register which delays turning off

the output buffers an additional cycle when a deselect is

executed.This feature allows depth expansion without penal-

izing system performance.

The CY7C1223H operates from a +3.3V core power supply

while all outputs operate with either a +3.3V/2.5V supply. All

inputs and outputs are JEDEC-standard JESD8-5-compatible.

Selection Guide

166 MHz 133 MHz Unit

Maximum Access Time 3.5 4.0 ns

Maximum Operating Current 240 225 mA

Maximum CMOS Standby Current 40 40 mA

Note:

1. For best-practices recommendations, please refer to the Cypr ess application note System Design Guidelines on www .cypress.com.

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 2 of 16

Logic Block Diagram

ADDRESS

ADV

CLK BURST

COUNTER AND

LOGIC

CLR

ADSC

DQP

BYTE

WRITE REGISTER

A ,

DQP

BYTE

WRITE REGISTER

ENABLE

SENSE

AMPS

MEMORY

ARRAY

ADSP

[1:0]

MODE

BWE

PIPELINED

ENABLE

DQP

OUTPUT

REGISTERS

INPUT

REGISTERS

OUTPUT

BUFFERS

B ,

DQP

BYTE

WRITE DRIVER

DQP

BYTE

WRITE DRIVER

SLEEP

CONTROL

0,A1,A

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 3 of 16

Pin Configurations

100-pin TQFP Pinout

VDDQ

VSSQ

DQPA

DQA

VSSQ

VDDQ

DQA

VSS

VDD

DQA

VDDQ

VSSQ

DQA

VSSQ

VDDQ

VSSQ

DQB

VSSQ

VDDQ

DQB

VDD

VSS

DQB

VDDQ

VSSQ

DQB

DQPB

VSSQ

VDDQ

CE1

CE2

BWB

BWA

CE3

VDD

VSS

CLK

BWE

ADSC

ADSP

ADV

100

CY7C1223H

NC/72M

NC/36M

VSS

VDD

NC/18M

NC/9M

NC/4M

MODE

Top View

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 4 of 16

Pin Descriptions

Pin Type Description

A0, A1, A Input-

Synchronous Address Inputs used to select one of the 128K address locations. Sampled at the rising

edge of the CLK if ADSP or ADSC is active LOW , and CE1, CE2, and CE3 are sampled active.

A[1:0] are fed to the two-bit counter.

BW[A:B] Input-

Synchronous Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM.

Sampled on the rising edge of CLK.

GW Input-

Synchronous Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a

global write is conducted (ALL bytes are written, regardless of the values on BW[A:B] and BWE).

BWE Input-

Synchronous Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must

be asserted LOW to conduct a byte write.

CLK Input-

Clock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the

burst counter when ADV is asserted LOW, during a burst operation.

CE1Input-

Synchronous Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction

with CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE1 is sampled

only when a new external address is loaded.

CE2Input-

Synchronous Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction

with CE1 and CE3 to select/deselect the device. CE2 is sampled on ly when a new external

address is loaded.

CE3Input-

Synchronous Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction

with CE1 and CE2 to select/deselect the device. CE3 is sampled only when a new external

address is loaded

OE Input-

Asynchronous Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When

LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act

as input data pins. OE is masked during the first clock of a read cycle when emerging from a

deselected state.

ADV Input-

Synchronous Advance Input signal, sampled on the rising edge of CLK, active LOW. When asserted, it

automatically increments the address in a burst cycle.

ADSP Input-

Synchronous Address Strob e from Processor, sampl e d o n the rising edge of CLK, activ e LOW. When

asserted LOW , addresses presented to the device are captured in the address registers. A[1:0]

are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP

is recognized. ASDP is ignored when CE1 is deasserted HIGH.

ADSC Input-

Synchronous Address Strobe from Con tro ller, sampled on the rising edg e of CLK, activ e LOW. When

asserted LOW , addresses presented to the device are captured in the address registers. A[1:0]

are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP

is recognized.

ZZ Input-

Asynchronous ZZ “sleep” Input, acti ve H IGH. When asserted HIGH places the device in a non-time-critical

“sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or

left floating. ZZ pin has an internal pull-down.

DQs

DQP[A:B]

I/O-

Synchronous Bidirectional Dat a I/O lines. As inputs, they feed into an on-chip data register that is triggered

by the rising edge of CLK. As outputs, they deliver the data contained in the memory location

specified by the addresses presented during the previous clock rise of the read cycle. The

direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs.

When HIGH, DQs and DQP[A:B] are placed in a tri-state condition.

VDD Power Supply Power supply inputs to the core of the devi ce.

VSS Ground Ground for the core of the de vice.

VDDQ I/O Power

Supply Power supply for the I/O circuitry.

VSSQ I/O Ground Ground for the I/O circuitry.

MODE Input-

Static Select s Burst Order . When tied to GND selects linear burst sequence. When tied to VDD or left

floating selects interleaved burst sequence. This is a strap pin and should remain static during

device operation. Mode Pin has an internal pull-up.

NC No Connects. Not internally connected to the die. 4M, 9M, 18M, 72M, 144M, 288M, 576M, and

1G are address expansion pins and are not internally connected to the die.

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 5 of 16

Functional Overview

All synchronous inputs pass through input registers controlled

by the rising edge of the clock. All data outputs pass through

output registers controlled by the rising edge of the clock.

The CY7C1223H supports secondary cache in systems

utilizing either a linear or interleaved burst sequence. The

interleaved burst order supports Pentium and i486™

processors. The linear burst sequence is suited for processors

that utilize a linear burst sequence. The burst order is user

selectable, and is determined by sampling the MODE input.

Accesses can be initiated with either the Processor Address

Strobe (ADSP) or the Controller Address Strobe (ADSC).

Address advancement through the burst sequence is

controlled by the ADV input. A two-bit on-chip wraparound

burst counter captures the first address in a burst sequence

and automatically increments the address for the rest of the

burst access.

Byte write operations are qualified with the Byte Write Enable

(BWE) and Byte Write Select (BW[A:B]) inputs. A Global Write

Enable (GW) overrides all byte write inputs and writes data to

all four bytes. All writes are simplified with on-chip

synchronous self-timed write circuitry.

Synchronous Chip Selects CE1, CE2, CE3 and an

asynchronous Output Enable (OE) provide for easy bank

selection and output tri-state control. ADSP is ignored if CE1

is HIGH.

Single Read Accesses

This access is initiated when the following conditions are

satisfied at clock rise: (1) ADSP or ADSC is asserted LOW , (2)

chip selects are all asserted active, and (3) the Write signals

(GW, BWE) are all deasserted HIGH. ADSP is igno re d if CE1

is HIGH. The address presented to the address inputs is

stored into the address advancement logic and the Address

sponding data is allowed to propagate to the input of the

Output Registers. At the rising edge of the next clock the data

is allowed to propagate through the output register and onto

the data bus within tCO if OE is active LOW . The only exception

occurs when the SRAM is emerging from a deselected state

to a selected state, it s outputs are always tri-stated during the

first cycle of the access. After the first cycle of the access, the

outputs are controlled by the OE signal. Consecutive single

read cycles are suppo rted.

The CY7C1223H is a double-cycle deselect part. Once the

SRAM is deselected at clock rise by the chip select and either

ADSP or ADSC signals, its output will tri-state immediately

after the next clock rise.

Single Write Accesses Initiated by ADSP

This access is initiated when both of the following conditions

are satisfied at clock rise: (1) ADSP is asserted LOW, and (2)

chip select is asserted active. The address presented is

loaded into the address register and the address

advancement logic while being delivered to the memory core.

The write signals (GW , BWE, and BW[A:B]) and ADV inputs are

ignored during this first cycle.

ADSP triggered write accesses require two clock cycles to

complete. If GW is asserted LOW on the second clock rise, the

data presented to the DQx inputs is written into the corre-

sponding address location in the memory core. If GW is HIGH,

then the write operation is controlled by BWE and BW[A:B]

signals. The CY7C1223H provide s Byte Write capability that

is described in the Write Cycle Description table. Asserting the

Byte Write Enable input (BWE) with the selected Byte Write

input will selective ly write to only the desired bytes. Bytes not

selected during a Byte Write operation will remain unalte red.

A synchronous self-timed write mechanism has been provided

to simplify the Write operations.

Because the CY7C1223H is a common I/O device, the Output

Enable (OE) must be deasserted HIGH before presenting data

to the DQ inputs. Doing so will tri-state the output drivers. As

a safety precaution, DQ are automatically tri-stated whenever

a write cycle is detected, regardless of the state of OE.

Single Write Accesses Initiated by ADSC

ADSC write accesses are initiated when the following condi-

tions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is

deasserted HIGH, (3) chip select is asserted active, and (4)

the appropriate combination of the write inputs (GW, BWE,

and BW[A:B]) are asserted active to conduct a write to the

desired byte(s). ADSC triggered write accesses require a

single clock cycle to complete. The address presented is

loaded into the address register and the address

advancem ent lo gic w hil e b eing d el ivere d to the m em ory core.

The ADV input is ignored during this cycle. If a global write is

conducted, the data presented to the DQX is written into the

corresponding address lo cation in the memory core. If a byte

write is conducted, only the sel ected bytes are written. Bytes

not selected during a byte write operation will remain

unaltered. A synchronous self-timed write mechanism has

been provided to simplify the write operations.

Because the CY7C1223H is a common I/O device, the Output

Enable (OE) must be deasserted HIGH before presenting data

to the DQX input s. Doing so will tri-state the output drivers. As

a safety precaution, DQX are automatically tri-stated

whenever a write cycle is detected, regardless of th e state of

OE.

Burst Sequences

The CY7C1223H provides a two-bit wraparound counter, fed

by A[1:0], that implements either an interleaved or linear burst

sequence. The interleaved burst sequence is designed specif-

ically to support Intel Pentium applications. The linear burst

sequence is designed to support processors that follow a

linear burst se quence. T he burst seq uence is user se lectable

through the MODE input. Both read and write burst operations

are supported.

Asserting ADV LOW at clock rise will automatically increment

the burst counter to the next address in the burst sequence.

Both read and write burst operations are supported.

Sleep Mode

The ZZ input pin is an asynchronous input. Asserting ZZ

places the SRAM in a power conservation “sleep” mode. Two

clock cycles are required to enter into or exit from this “sleep”

mode. While in this mode, data integrity is guaranteed.

Accesses pending when entering the “sleep” mode are not

considered valid nor is the completion of the operation

guaranteed. The device must be deselected p rior to entering

the “sleep” mode. CEs, ADSP, and ADSC must remain

inactive for the duration of tZZREC after the ZZ input returns

LOW.

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 6 of 16

Interleaved Burst Address Table (MODE = Floating or VDD)

First

Address

A1, A0

Second

Address

A1, A0

Third

Address

A1, A0

Fourth

Address

A1, A0

00 01 10 11

01 00 11 10

10 11 00 01

11 10 01 00

Linear Burst Address Table (MODE = GND)

First

Address

A1, A0

Second

Address

A1, A0

Third

Address

A1, A0

Fourth

Address

A1, A0

00 01 10 11

01 10 11 00

10 11 00 01

11 00 01 10

Truth Table [2, 3, 4, 5, 6]

Operation Address

Used CE1CE2CE3ZZ ADSP ADSC ADV WRITE OE CLK DQ

Deselected Cycle, Power-down None H X X L X L X X X L-H Tri-State

Deselected Cycle, Power-down None L L X L L X X X X L -H Tri-State

Deselected Cycle, Power-down None L X H L L X X X X L-H Tri-State

Deselected Cycle, Power-down None L L X L H L X X X L-H Tri-State

Deselected Cycle, Power-down None L X H L H L X X X L -H Tri-State

ZZ Mode, Power-down None X X X H X X X X X X Tri-State

Read Cycle, Begin Burst External L H L L L X X X L L-H Q

Read Cycle, Begin Burst External L H L L L X X X H L-H Tri-State

Write Cycle, Begin Burst External L H L L H L X L X L-H D

Read Cycle, Begin Burst External L H L L H L X H L L-H Q

Read Cycle, Begin Burst External L H L L H L X H H L-H Tri-State

Read Cycle, Continue Burst Next X X X L H H L H L L-H Q

Read Cycle, Continue Burst Next X X X L H H L H H L-H Tri-State

Read Cycle, Continue Burst Next H X X L X H L H L L-H Q

Read Cycle, Continue Burst Next H X X L X H L H H L-H Tri-State

Write Cycle, Continue Burst Next X X X L H H L L X L-H D

Write Cycle, Continue Burst Next H X X L X H L L X L - H D

Read Cycle, Suspend Burst Current X X X L H H H H L L -H Q

Read Cycle, Suspend Burst Current X X X L H H H H H L-H Tri-State

Read Cycle, Suspend Burst Current H X X L X H H H L L-H Q

Read Cycle, Suspend Burst Current H X X L X H H H H L-H Tr i-State

Write Cycle, Suspend Burst Current X X X L H H H L X L-H D

Write Cycle, Suspend Burst Current H X X L X H H L X L-H D

Notes:

2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.

3. WRITE = L when any one or more Byte Write ena ble signals (BW A, B WB) and BWE = L or GW = L. WRITE = H when all Byte write enabl e signals (BWA, BWB),

BWE, GW=H.

4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.

5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the st ate of GW, BWE, or BW[A:B]. Writes may occur only on subseq uent cl ocks

after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a

don't care for the remainder of the write cycle.

6. OE is asynchronous and is not samp led with the clock ri se. It is masked internally during write cycl es. During a read cycle all d ata bit s are tri-state when OE is

inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 7 of 16

Truth Table for Read/Write[2, 3]

Function GW BWE BWABWB

Read H H X X

Read H L H H

Write byte A - (DQA and DQPA)H L L H

Write byte B- (DQB and DQPB)H L H L

Write all bytes H L L L

Write all bytes L X X X

ZZ Mode Electrical Characteristics

Parameter Description Test Conditions Min. Max. Unit

IDDZZ Sleep mode standby current ZZ > VDD − 0.2V 40 mA

tZZS Device operation to ZZ ZZ > VDD − 0.2V 2tCYC ns

tZZREC ZZ recovery time ZZ < 0.2V 2tCYC ns

tZZI ZZ Active to sleep current This parameter is sampled 2tCYC ns

tRZZI ZZ inactive to exit sleep current This parameter is sampled 0 ns

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 8 of 16

Maximum Ratings

(Above which the useful life may be impaired. For user guide-

lines, not tested.)

Storage Temperature .............. ... ... ... ............. –65°C to +150°

Ambient Temperature with

Power Applied.............................................–55°C to +125°C

Supply Voltage on VDD Relative to GND........–0.5V to +4.6V

Supply Voltage on VDDQ Relative to GND......–0.5V to +VDD

DC Voltage Appli ed to Outputs

in tri-state ............................................ –0.5V to VDDQ +0.5V

DC Input Voltage .....................................–0.5V to VDD+0.5V

Current into Outputs (LOW).........................................20 mA

Static Discharge Voltage...........................................> 2001V

(per MIL-STD-883,Method 3015)

Latch-up Current.....................................................> 200 mA

Operating Range

Range Ambient

Temperature (TA)V

DD VDDQ

Com’l 0°C to +70°C 3.3V −5%/+10% 2.5V−5% to

VDD

Ind’l –40°C to +85°C

Electrical Characteristics Over the Operating Range[7, 8]

Parameter Description Test Conditions Min. Max. Unit

VDD Power Supply Voltage 3.135 3.6 V

VDDQ I/O Supply Voltage for 3.3V I/O 3.135 VDD V

for 2.5V I/O 2.375 2.625

VOH Output HIGH Voltage for 3.3V I/O, IOH = –4.0 mA 2.4 V

for 2.5V I/O, IOH = –1.0 mA 2.0

VOL Output LOW Voltage for 3.3V I/O, IOL = 8.0 mA 0.4 V

for 2.5V I/O, IOL = 1.0 mA 0.4

VIH Input HI GH Voltage [7] for 3.3V I/O 2.0 VDD + 0.3V V

for 2.5V I/O 1.7 VDD + 0.3V V

VIL Input LOW Voltage[7] for 3.3V I/O –0.3 0.8 V

for 2.5V I/O –0.3 0.7 V

IXInput Leakage Current

except ZZ and MODE GND ≤ VI ≤ VDDQ –5 5 µA

Input Current of MODE Input = VSS –30 µA

Input = VDD 5µA

Input Current of ZZ Input = VSS –5 µA

Input = VDD 30 µA

IOZ Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled –5 5 µA

IDD VDD Operating Supply

Current VDD = Max., IOUT = 0 mA,

f = fMAX = 1/tCYC 6-ns cycle, 166 MHz 240 mA

7.5-ns cycle,133MHz 225 mA

ISB1 Automatic CS

Power-down

Current—TTL Inputs

VDD = Max., Device Deselected,

VIN ≥ VIH or VIN ≤ VIL,

f = fMAX = 1/tCYC

6-ns cycle, 166 MHz 100 mA

7.5-ns cycle,133MHz 90 mA

ISB2 Automatic CS

Power-down

Current—CMOS Inputs

VDD = Max., Device Deselected,

VIN ≤ 0.3V or VIN > VDDQ – 0.3V ,

f = 0

All speeds 40 mA

ISB3 Automatic CS

Power-down

Current—CMOS Inputs

VDD = Max., Device Deselected,

or VIN ≤ 0.3V or

VIN > VDDQ – 0.3V,

f = fMAX = 1/tCYC

6.0-ns cycle, 166 MHz 85 mA

7.5-ns cycle, 133MHz 75 mA

ISB4 Automatic CS

Power-down

Current—TTL Inputs

VDD = Max., Device Deselected,

VIN ≥ VIH or VIN ≤ VIL, f = 0 All speeds 45 mA

Notes:

7. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC)> –2V (Pulse width less than tCYC/2).

8. Power-up: Assumes a linear ramp from 0V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 9 of 16

Capacitance[9]

Parameter Description Test Conditions 100 TQFP

Max. Unit

CIN Input Capacitance TA = 25°C, f = 1 MHz,

VDD = 3.3V

VDDQ = 2.5V

5pF

CCLK Clock Input Capacitance 5 pF

CI/O Input/Output Capacitance 5 pF

Thermal Characteristics[9]

Parameter Description Test Conditions 100 TQFP

Package Unit

ΘJA Thermal Resistance

(Junction to Ambient) Test conditions follow standard

test methods and procedures for

measuring thermal impedance,

per EIA/JESD51

30.32 °C/W

ΘJC Thermal Resistance

(Junction to case) 6.85 °C/W

AC Test Loads and Waveforms

Note:

9. Tested initially and after any design or pro ce ss change that may affect t hese parameters.

OUTPUT

R = 317Ω

R = 351Ω

5pF

INCLUDING

JIG AND

SCOPE

(a) (b)

OUTPUT

RL= 50Ω

Z0= 50Ω

= 1.5V

3.3V ALL INPUT PULSES

VDDQ

GND

90%

10% 90%

10%

≤1 ns ≤1 ns

(c)

3.3V I/O Test Load

OUTPUT

R = 1667Ω

R =1538Ω

5pF

INCLUDING

JIG AND

SCOPE

(a) (b)

OUTPUT

RL= 50Ω

Z0= 50Ω

VT= 1.25V

2.5V ALL INPUT PULSES

VDDQ

GND

90%

10% 90%

10%

≤1 ns ≤1 ns

(c)

2.5V I/O Test Load

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 10 of 16

Switching Characteristics Over the Operating Range [14, 15]

Parameter Description

166 MHz 133 MHz

UnitMin. Max. Min. Max.

tPOWER VDD(Typical) to the first Access[10] 11 ms

Clock

tCYC Clock Cycle Time 6.0 7.5 ns

tCH Clock HIGH 2.5 3.0 ns

tCL Clock LOW 2.5 3.0 ns

Output Times

tCO Data Output Valid After CLK Rise 3.5 4.0 ns

tDOH Data Output Hold After CLK Rise 1.5 1.5 ns

tCLZ Clock to Low-Z[11, 12, 13] 00 ns

tCHZ Clock to High-Z[11, 12, 13] 3.5 4.0 ns

tOEV OE LOW to Output Valid 3.5 4.0 ns

tOELZ OE LOW to Output Low-Z[11, 12, 13] 00 ns

tOEHZ OE HIGH to Output High-Z[11, 12, 13] 3.5 4.0 ns

Set-up Times

tAS Address Set-up Before CLK Rise 1.5 1.5 ns

tADS ADSC, ADSP Set-up Before CLK Rise 1.5 1.5 ns

tADVS ADV Set-up Before CLK Rise 1.5 1.5 ns

tWES GW, BWE, BW[A:B] Set-up Before CLK Rise 1.5 1.5 ns

tDS Data Input Set-up Before CLK Rise 1.5 1.5 ns

tCES Chip Enable Set-up Before CLK Rise 1.5 1.5 ns

Hold Times

tAH Address Hold After CLK Rise 0.5 0.5 ns

tADH ADSP , ADSC Hold After CLK Rise 0.5 0.5 ns

tADVH ADV Hold After CLK Rise 0.5 0.5 ns

tWEH GW,BWE, BW[A : B] Hold After CL K Ri se 0.5 0.5 ns

tDH Data Input Hold After CLK Rise 0.5 0.5 ns

tCEH Chip Enable Hold After CLK Rise 0.5 0.5 ns

Notes:

10.This p art ha s a vo lt age re gulat or intern ally; tpower is the time t hat t he powe r needs to be suppli ed a bove V DD minimum initia lly be for e a re ad o r write ope ration

can be initiated.

11. tCHZ, tCLZ, tOELZ, and tOEHZ are specified with AC test condit ions shown in part (b) of AC Test Loads. T ransitio n is measured ± 200 mV from steady-state vo ltage.

12.At any given voltage and temperature, t OEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus co ntention between SRAMs when sharing the same

data bus. These specif icati ons do not imply a bus content ion condition, but reflect parameters guaranteed over worst case user cond itio ns. Device is design ed

to achieve High-Z prior to Low-Z under the same system conditions.

13.This parameter is sampled and not 100% tested.

14.Timing reference level is 1.5V when VDDQ = 3.3V and 1.25V when VDDQ = 2.5V.

15.Test conditions shown in (a) of AC Test Loads unless otherwise noted.

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 11 of 16

Switching Waveforms

Read Timing[16]

Note:

16.On this diagram, when CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.

tCYC

tCL

CLK

ADSP

tADH

tADS

ADDRESS

tCH

ADSC

tAH

tAS

tCEH

tCES

W, BWE,BW

Data Out (Q) High-Z

tDOH

tCO

ADV

tOEHZ

tCO

Single READ BURST READ

tOEV

tOELZ tCHZ

Burst wraps around

to its initial state

tADVH

tADVS

tWEH

tWES

tADH

tADS

Q(A2) Q(A2 + 1) Q(A2 + 2)

Q(A1) Q(A2) Q(A2 + 1) Q(A3)Q(A2 + 3)

A2 A3

Deselect

cycle

Burst continued with

new base address

ADV suspends burst

DON’T CARE UNDEFINED

[A:B]

CLZ

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 12 of 16

Write Tim ing[16, 17]

Note:

17.Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A:B] LOW.

Switching Waveforms (continued)

tCYC

tCL

CLK

ADSP

tADH

tADS

ADDRESS

tCH

ADSC

tAH

tAS

tCEH

tCES

BWE,

BW[A:B]

ADV

BURST READ BURST WRITE

D(A2) D(A2 + 1) D(A2 + 1) D(A3) D(A3 + 1) D(A3 + 2)D(A2 + 3)

A2 A3

Extended BURST WRITE

D(A2 + 2)

Single WRITE

tADH

tADS

tADH

tADS

OEHZ

tADVH

tADVS

tWEH

tWES

tDH

tDS

tWEH

tWES

Byte write signals are ignored for first cycle when

ADSP initiates burst

ADSC extends burst

ADV suspends burst

DON’T CARE UNDEFINED

D(A1)

High-Z

Data in (D)

ata Out (Q)

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 13 of 16

Read/Write Timing[16, 18, 19]

Notes:

18.The data bus (Q) remains in High-Z following a Write cycle, unless a new read access initiated by ADSC or ADSP.

19.GW is HIGH.

Switching Waveforms (continued)

CYC

tCL

CLK

ADSP

tADH

tADS

ADDRESS

tCH

ADSC

tAH

tAS

tCEH

tCES

Data Out (Q) High-Z

ADV

Single WRITE

D(A3)

A4 A5 A6

D(A5) D(A6)

Data In (D)

BURST READBack-to-Back READs

High-Z

Q(A2)Q(A1) Q(A4) Q(A4+1) Q(A4+2)

tWEH

tWES

Q(A4+3)

tOEHZ

tDH

tDS

tOELZ

tCLZ

tCO

Back-to-Back

WRITEs

BWE, BW

[A:B]

DON’T CARE UNDEFINED

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 14 of 16

ZZ Mode Timing [20,21]

Notes:

20.Device must be deselected when entering ZZ mode. See truth table fo r all possible signal conditions to deselect the device.

21.DQs are in High-Z when exiting ZZ sleep mode.

Switching Waveforms (continued)

tZZ

SUPPLY

CLK

tZZREC

LL INPUTS

(except ZZ)

DON’T CARE

IDDZZ

tZZI

tRZZI

Outputs (Q)

High-Z

DESELECT or READ Only

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 15 of 16

© Cypress Semi con duct or Cor po rati on , 20 06 . The information con t a in ed he re i n is subject to change wi t hou t n oti ce. C ypr ess S em ic onductor Corporation assumes no resp onsibility f or the u se

of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be

used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypr ess. Furtherm ore, Cypress doe s not authorize i ts

products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant inju ry to the user. The inclusion of Cypress

products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Intel and Pentium are reg istered trademarks, and i486 is a trademark, of Intel Corporat ion. PowerPC is a regi stered trademark

of IBM. All product and company names mentioned in this document are the trademarks of their respective holders.

Ordering Information

“Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or

visit www.cypress.com for actual products offered”.

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

166 CY7C1223H-166AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial

CY7C1223H-166AXI 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Industrial

133 CY7C1223H-133AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial

CY7C1223H-133AXI 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Industrial

Package Diagram

NOTE:

1. JEDEC STD REF MS-026

2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH

MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE

3. DIMENSIONS IN MILLIMETERS

BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH

0.30±0.08

0.65

20.00±0.10

22.00±0.20

1.40±0.05

12°±1°

1.60 MAX.

0.05 MIN.

0.60±0.15

0° MIN.

0.25

0°-7°

(8X)

STAND-OFF

R 0.08 MIN.

TYP.

0.20 MAX.

0.15 MAX.

0.20 MAX.

R 0.08 MIN.

0.20 MAX.

14.00±0.10

16.00±0.20

0.10

SEE DETAIL A

DETAIL

100

31 50

GAUGE PLANE

1.00 REF.

0.20 MIN.

SEATING PLANE

100-pin TQFP (14 x 20 x 1.4 mm) (51-85050)

51-85050-*B

[+] Feedback [+] Feedback

CY7C1223H

Document #: 38-05674 Rev. *B Page 16 of 16

Document History Page

Document Title: CY7C1223H 2-Mbit (128K x 18) Pipelined DCD Sync SRAM

Document Number: 38-05674

REV. ECN NO. Issue Date Orig. of

Change Description of Change

** 347357 See ECN PCI New Data Sheet

*A 424820 See ECN RXU Changed address of Cypress Semiconductor Corporation on Page# 1 from

“3901 North First Street” to “198 Champion Court”

Changed Three-State to Tri-State.

Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the

Electrical Characteristics Table.

Modified test condition from VIH < VDD to VIH < VDD

Replaced Package Name column with Package Diagram in the Ordering

Information table.

Replaced Package Diagram of 51-85050 from *A to *B

*B 459347 See ECN NXR Converted from Preliminary to Final

Included 2.5V I/O option

Updated the Ordering Information table.

[+] Feedback [+] Feedback