W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Description The TS5A3159 is a single-pole double-throw (SPDT) analog switch that is designed to operate from 1.65 V to 5.5 V. The device offers a low ON-state resistance and an excellent ON-resistance, matching with the break-before-make feature to prevent signal distortion during the transferring of a signal from one channel to another. The device has an excellent total harmonic distortion (THD) performance and consumes very low power. These features make this device suitable for portable audio applications. Features D Specified Break-Before-Make Switching D Low ON-State Resistance (1 W) D Control Inputs Are 5-V Tolerant D Low Charge Injection D Excellent ON-Resistance Matching D Low Total Harmonic Distortion D 1.65-V to 5.5-V Single-Supply Operation D Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II D ESD Performance Tested Per JESD 22 - 2000-V Human-Body Model (A114-B, Class II) - 1000-V Charged-Device Model (C101) Applications D Cell Phones D PDAs D Portable Instrumentation Summary of Characteristics V+ = 5 V and TA = 25 C 2:1 Multiplexer/ Demultiplexer (1 x SPDT) Configuration SOT-23 OR SC-70 PACKAGE (TOP VIEW) Number of channels 1 ON-state resistance (ron) NO 1 TS5A3159 1.1 6 IN ON-state resistance match (ron) 0.1 ON-state resistance flatness (ron(flat)) 0.15 GND 2 5 V+ NC 3 4 COM Turn on/turn off time (tON/tOFF) 20 ns/15 ns Break-before-make time (tBBM) 12 ns Charge injection (QC) Bandwidth (BW) FUNCTION TABLE 36 pC 100 MHz OFF isolation (OISO) -65 dB at 1 MHz Crosstalk (XTALK) -65 dB at 1 MHz IN NC TO COM, COM TO NC NO TO COM, COM TO NO L ON OFF Leakage current (INO(OFF)/INC(OFF)) H OFF ON Package option Total harmonic distortion (THD) 0.01% 20 nA 6-pin DBV or DCK Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. ! "#$ %!& % "! "! '! ! !( ! %% )*& % "!+ %! !!$* $%! !+ $$ "!!& Copyright 2005, Texas Instruments Incorporated W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 ORDERING INFORMATION PACKAGE(1) TA -40C to 85C SOT (SOT-23) - DBV SOT (SC-70) - DCK(2) ORDERABLE PART NUMBER TOP-SIDE MARKING(2) Tape and reel TS5A3159DBVR JA8_ Tape and reel TS5A3159DCKR JA_ (1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. (2) DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site. Absolute Maximum Ratings(1) over operating free-air temperature range (unless otherwise noted) MIN V+ VNO, VCOM Supply voltage range(2) Analog voltage range(2)(3)(4) II/OK INO, ICOM Analog port diode current VIN IIK ON-state switch current Digital input clamp current Continuous current through V+ or GND Package thermal impedance(6) 6.5 V -0.5 V+ + 0.5 50 mA 200 mA 400 mA 6.5 V -50 mA 100 mA -0.5 VIN < 0 UNIT -0.5 VNO, VCOM < 0 or VNO, VCOM > V+ VNO, VCOM = 0 to V+ ON-state peak switch current(5) Digital input voltage range(2)(3) MAX V JA 165 C Tstg Storage temperature range -65 150 C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) All voltages are with respect to ground, unless otherwise specified. (3) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. (4) This value is limited to 5.5 V maximum. (5) Pulse at 1 ms duration < 10% duty cycle. (6) The package thermal impedance is calculated in accordance with JESD 51-7. 2 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 5-V Supply V+ = 4.5 V to 5.5 V and TA = -40C to 85C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP(1) MAX UNIT 0 V+ V Analog Switch Analog signal range VCOM, VNO, VNC rpeak 0 VNO or VNC V+, ICOM = -30 mA, Switch ON, See Figure 11 25C Peak ON resistance ron VNO or VNC = 2.5 V, ICOM = -30 mA, Switch ON, See Figure 11 25C ON-state resistance ON-state resistance match between channels ron VNO or VNC = 2.5 V, ICOM = -30 mA, Switch ON, See Figure 11 0 VNO or VNC V+, ICOM = -30 mA, VNO or VNC = 1 V, 1.5 V, 2.5 V, ICOM = -30 mA, Switch ON, See Figure 11 Full Full 25C 1 4.5 V 1.5 0.75 4.5 V ron(flat) NC, NO OFF leakage current INC(OFF), INO(OFF) VNC or VNO = 4.5 V, VCOM = 0, Switch OFF, See Figure 12 25C NC, NO ON leakage current INC(ON), INO(ON) VNC or VNO = 4.5 V, VCOM = Open, Switch ON, See Figure 13 25C COM ON leakage current VNC or VNO = 4.5 V or Open, VCOM = 4.5 V, Switch ON, See Figure 13 25C ICOM(ON) 1.1 1.1 4.5 V 25C Full Full 0.233 4.5 V Full 0.1 25C ON-state resistance flatness 1.5 0.15 -2 5.5 V -20 -4 5.5 V 2 20 2.8 -40 -4 5.5 V 0.2 4 40 0.47 nA nA 4 nA -40 40 Full 2.4 5.5 V Full 0 0.8 V -1 1 A Digital Inputs (IN) Input logic high Input logic low Input leakage current (1) TA = 25C VIH VIL IIH, IIL VIN = 5.5 V or 0 Full 5.5 V 3 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 5-V Supply (continued) V+ = 4.5 V to 5.5 V and TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL MIN TYP(1) TA V+ 4.5 V to 5.5 V 20 4.5 V to 5.5 V 15 MAX UNIT Dynamic Turn-on time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tON Turn-off time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tOFF Break-before-make time VNC = VNO = V+/2, RL = 50 , CL = 35 pF, See Figure 16 25C tBBM Full 4.5 V to 5.5 V Full Full 35 40 20 35 1 12 ns ns 14.5 ns 1 Charge injection QC CL = 1 nF, VGEN = 0 V, See Figure 20 25C 5V 36 pC NC, NO OFF capacitance CNC(OFF), CNO(OFF) VNC or VNO = V+ or GND, Switch OFF, See Figure 14 25C 5V 23 pF NC, NO ON capacitance CNC(ON), CNO(ON) VNC or VNO = V+ or GND, Switch ON, See Figure 14 25C 5V 84 pF COM ON capacitance CCOM(ON) VCOM = V+ or GND, Switch ON, See Figure 14 25C 5V 84 pF Digital input capacitance CIN VIN = V+ or GND, See Figure 14 25C 5V 2.1 pF Bandwidth BW RL = 50 , Switch ON, See Figure 17 25C 5V 100 MHz OISO RL = 50 , f = 1 MHz, Switch OFF, See Figure 18 25C 5V -65 dB XTALK RL = 50 , f = 1 MHz, Switch ON, See Figure 19 25C 5V -65 dB THD RL = 600 , CL = 50 pF, f = 600 Hz to 20 kHz, See Figure 21 25C 5V 0.01 % VIN = V+ or GND, Switch ON or OFF Full 5.5 V OFF isolation Crosstalk Total harmonic distortion Supply Positive supply current (1) TA = 25C 4 I+ 0.1 A W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 3.3-V Supply V+ = 3 V to 3.6 V and TA = -40C to 85C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP(1) MAX UNIT 0 V+ V Analog Switch Analog signal range VCOM, VNO, VNC Peak ON-state resistance rpeak ON-state resistance ron ON-state resistance match between channels 0 VNO or VNC V+, ICOM = -24 mA, Switch ON, See Figure 11 25C VNO or VNC = 2 V, ICOM = -24 mA, Switch ON, See Figure 11 25C ron VNO or VNC = 2 V, 0.8 V, ICOM = -24 mA, Switch ON, See Figure 11 ON-state resistance flatness ron(flat) 0 VNO or VNC V+, ICOM = -24 mA, VNO or VNC = 2 V, 0.8 V, ICOM = -24 mA, Switch ON, See Figure 11 NC, NO OFF leakage current INC(OFF), INO(OFF) VNC or VNO = 3 V, VCOM = 0, Switch OFF, See Figure 12 25C 3.6 V 0.2 nA NC, NO ON leakage current INC(ON), INO(ON) VNC or VNO = 3 V, VCOM = Open, Switch ON, See Figure 13 25C 3.6 V 2.8 nA COM ON leakage current ICOM(ON) VNC or VNO = 3 V or Open, VCOM = 3 V, Switch ON, See Figure 13 25C 3.6 V 0.47 nA Full Full 25C 1.35 2.1 3V 2.1 1.15 1.5 3V 1.5 3V 0.11 25C 0.225 3V 25C 0.25 Digital Inputs (IN) Input logic high Input logic low Input leakage current (1) TA = 25C VIH VIL IIH, IIL Full 2 Full VIN = 5.5 V or 0 Full 0 3.6 V -1 5.5 V 1 A 0.6 V 5 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 3.3-V Supply (continued) (V+ = 3 V to 3.6 V and TA = -40 C to 85 C) (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL MIN TYP(1) TA V+ 3 V to 3.6 V 30 3 V to 3.6 V 20 MAX UNIT Dynamic Turn-on time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tON Turn-off time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tOFF Break-before-make time VNC = VNO = V+/2, RL = 50 , CL = 35 pF, See Figure 16 25C tBBM Full 3 V to 3.6 V Full Full 40 55 25 40 1 21 ns ns 29 ns 1 Charge injection QC CL = 1 nF, VGEN = 0 V, See Figure 20 25C 3.3 V 20 pC NC, NO OFF capacitance CNC(OFF), CNO(OFF) VNC or VNO = V+ or GND, Switch OFF, See Figure 14 25C 3.3 V 23 pF NC, NO ON capacitance CNC(ON), CNO(ON) VNC or VNO = V+ or GND, Switch ON, See Figure 14 25C 3.3V 84 pF COM ON capacitance CCOM(ON) VCOM = V+ or GND, Switch ON, See Figure 14 25C 3.3 V 84 pF Digital input capacitance CIN VIN = V+ or GND, See Figure 14 25C 3.3 V 2.1 pF Bandwidth BW RL = 50 , Switch ON, See Figure 17 25C 3.3 V 100 MHz OISO RL = 50 , f = 1 MHz, Switch OFF, See Figure 18 25C 3.3 V -65 dB XTALK RL = 50 , f = 1 MHz, Switch ON, See Figure 19 25C 3.3 V -65 dB THD RL = 600 , CL = 50 pF, f = 600 Hz to 20 kHz, See Figure 21 25C 3.3 V 0.015 % VIN = V+ or GND, Switch ON or OFF Full 3.6 V OFF isolation Crosstalk Total harmonic distortion Supply Positive supply current (1) TA = 25C 6 I+ 0.1 A W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 2.5-V Supply V+ = 2.3 V to 2.7 V and TA = -40C to 85C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP(1) MAX UNIT 0 V+ V Analog Switch Analog signal range VCOM, VNO, VNC Peak ON-state resistance 0 VNO or VNC V+, ICOM = -8 mA, Switch ON, See Figure 11 25C rpeak ron VNO or VNC = 1.8 V, ICOM = -8 mA, Switch ON, See Figure 11 25C ON-state resistance ON-state resistance match between channels ron VNO or VNC = 0.8 V, 1.8 V, ICOM = -8 mA, Switch ON, See Figure 11 ON-state resistance flatness ron(flat) 0 VNO or VNC V+, ICOM = -8 mA, VNO or VNC = 0.8 V, 1.8 V, ICOM = -8 mA, Switch ON, See Figure 11 NC, NO Off leakage current INC(OFF), INO(OFF) VNC or VNO = 2.3 V, VCOM = 0, Switch OFF, See Figure 12 25C 2.7 V 0.2 nA NC, NO On leakage current INC(ON), INO(ON) VNC or VNO = 2.3 V, VCOM = Open, Switch ON, See Figure 13 25C 2.7 V 2.8 nA COM On leakage current ICOM(ON) VNC or VNO = 2.3 V or Open, VCOM = 2.3 V, Switch ON, See Figure 13 25C 2.7 V 0.47 nA Full Full 25C 1.7 2.7 2.5 V 2.7 1.45 2 2.5 V 2 2.5 V 0.7 25C 0.5 2.5 V 25C 0.45 Digital Inputs (IN) Input logic high Input logic low Input leakage current (1) TA = 25C VIH VIL IIH, IIL Full 1.8 Full VIN = 5.5 V or 0 Full 0 2.7 V -1 5.5 V 1 A 0.6 V 7 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 2.5-V Supply (continued) V+ = 2.3 V to 2.7 V and TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL MIN TYP(1) TA V+ 2.3 V to 2.7 V 40 2.3 V to 2.7 V 30 MAX UNIT Dynamic Turn-on time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tON Turn-off time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tOFF Break-before-make time VNC = VNO = V+/2, RL = 50 , CL = 35 pF, See Figure 16 25C tBBM Full 2.3 V to 2.7 V Full Full 55 70 40 55 1 33 ns ns 39 ns 1 Charge injection QC CL = 1 nF, VGEN = 0 V, See Figure 20 25C 2.5 V 13 pC NC, NO OFF capacitance CNC(OFF), CNO(OFF) VNC or VNO = V+ or GND, Switch OFF, See Figure 14 25C 2.5 V 23 pF NC, NO ON capacitance CNC(ON), CNO(ON) VNC or VNO = V+ or GND, Switch ON, See Figure 14 25C 2.5V 84 pF COM ON capacitance CCOM(ON) VCOM = V+ or GND, Switch ON, See Figure 14 25C 2.5 V 84 pF Digital input capacitance CIN VIN = V+ or GND, See Figure 14 25C 2.5 V 2.1 pF Bandwidth BW RL = 50 , Switch ON, See Figure 17 25C 2.5 V 100 MHz OISO RL = 50 , f = 1 MHz, Switch OFF, See Figure 18 25C 2.5 V -64 dB XTALK RL = 50 , f = 1 MHz, Switch ON, See Figure 19 25C 2.5 V -64 dB THD RL = 600 , CL = 50 pF, f = 600 Hz to 20 kHz, See Figure 21 25C 2.5 V 0.025 % VIN = V+ or GND, Switch ON or OFF Full 2.7 V OFF isolation Crosstalk Total harmonic distortion Supply Positive supply current (1) TA = 25C 8 I+ 0.1 A W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 1.8-V Supply V+ = 1.65 V to 1.95 V and TA = -40C to 85C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP(1) MAX UNIT 0 V+ V Analog Switch Analog signal range VCOM, VNO, VNC Peak ON-state resistance 0 VNO or VNC V+, ICOM = -2 mA, Switch ON, See Figure 11 25C rpeak ron VNO or VNC = 1.5 V, ICOM = -2 mA, Switch ON, See Figure 11 25C ON-state resistance ON-state resistance match between channels VNO or VNC = 0.6 V, 1.5 V, ICOM = -2 mA, Switch ON, See Figure 11 25C ron ON-state resistance flatness ron(flat) 0 VNO or VNC V+, ICOM = -2 mA, VNO or VNC = 0.6 V, 1.5 V, ICOM = -2 mA, Switch ON, See Figure 11 Full Full 4 4.9 1.8 V 4.9 1.7 3.2 1.8 V 3.2 0.7 1.8 V Full 0.7 25C 1.85 Full 25C 1.85 1.8 V 0.9 Full 0.9 NC, NO Off leakage current INC(OFF), INO(OFF) VNC or VNO = 1.65 V, VCOM = 0, Switch OFF, See Figure 12 25C 1.95 V 0.2 nA NC, NO On leakage current INC(ON), INO(ON) VNC or VNO = 1.65 V, VCOM = Open, Switch ON, See Figure 13 25C 1.95 V 2.8 nA COM On leakage current ICOM(ON) VNC or VNO = 1.65 V or Open, VCOM = 1.65 V, Switch ON, See Figure 13 25C 1.95 V 0.47 nA Digital Inputs (IN) Input logic high Input logic low VIH VIL Input leakage current IIH, IIL VIN = 5.5 V or 0 Full 1.5 Full 0 Full 1.95 V -1 5.5 0.6 V V 1 A (1) TA = 25C 9 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 Electrical Characteristics for 1.8-V Supply (continued) V+ = 1.65 V to 1.95 V and TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL MIN TYP(1) TA V+ 1.65 V to 1.95 V 65 1.65 V to 1.95 V 40 MAX UNIT Dynamic Turn-on time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tON Turn-off time VCOM = V+, RL = 50 , CL = 35 pF, See Figure 15 25C tOFF Break-before-make time VNC = VNO = V+/2, RL = 50 , CL = 35 pF, See Figure 16 25C tBBM Full 1.65 V to 1.95 V Full Full 70 95 55 70 1 60 ns ns 72 ns 0.5 Charge injection QC CL = 1 nF, VGEN = 0 V, See Figure 20 25C 1.8 V 13 pC NC, NO OFF capacitance CNC(OFF), CNO(OFF) VNC or VNO = V+ or GND, Switch OFF, See Figure 14 25C 1.8 V 23 pF NC, NO ON capacitance CNC(ON), CNO(ON) VNC or VNO = V+ or GND, Switch ON, See Figure 14 25C 1.8V 84 pF COM ON capacitance CCOM(ON) VCOM = V+ or GND, Switch ON, See Figure 14 25C 1.8 V 84 pF Digital input capacitance CIN VIN = V+ or GND, See Figure 14 25C 1.8 V 2.1 pF Bandwidth BW RL = 50 , Switch ON, See Figure 17 25C 1.8 V 100 MHz OISO RL = 50 , f = 1 MHz, Switch OFF, See Figure 18 25C 1.8 V -63 dB XTALK RL = 50 , f = 1 MHz, Switch ON, See Figure 19 25C 1.8 V -63 dB VIN = V+ or GND, Switch ON or OFF Full 1.95 V OFF isolation Crosstalk Supply Positive supply current (1) TA = 25C 10 I+ 0.1 A W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 TYPICAL PERFORMANCE 3.5 1.6 TA = 255C 3 1.4 2.5 1.2 V+ = 1.8 V TA = 85C TA = 25C 1 ron () 2 ron () V+ = 3 V V+ = 2.5 V 1.5 TA = -40C 0.8 V+ = 3 V 0.6 1 0.4 V+ = 4.5 V 0.5 0.2 0 0 1 2 3 4 0 0 1 VCOM (V) Figure 1. ron vs VCOM Figure 2. ron vs VCOM V+ = 4.5 V V+ = 5 V 16 1 14 TA = 85C 12 Leakage (nA) 0.8 ron () 3 18 1.2 TA = 25C 0.6 TA = -40C 10 INC(ON) 8 6 0.4 ICOM(ON) 4 0.2 0 2 VCOM (V) INO(ON) 2 INO(OFF) 0 0 1 2 3 -40 4 INC(OFF) -20 0 VCOM (V) 20 40 60 80 100 Temperature (C) Figure 3. ron vs VCOM Figure 4. Leakage Current vs Temperature 50 20 VCOM = V+ TA = 25C tr < 20 ns tf < 20 ns 40 tr = 2.5 ns tf = 2.5 ns V+ = 5 V 18 16 tON/OFF (ns) tON/OFF (ns) 14 30 20 12 10 8 6 4 10 2 0 0 0 1 2 3 4 Supply Voltage (V) Figure 5. tON/OFF vs V+ 5 6 -40 -20 0 20 40 60 80 100 Temperature (C) Figure 6. tON/OFF vs Temperature 11 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 0 0 OFF Isolation -10 -1 Vt+ Bandwidth -20 -2 -30 Vt- 1.5 Gain (dB) Logic Threshold (Vt+/Vt-) 2 1 0.5 0 1.5 2 2.5 3 3.5 4 4.5 -4 -50 -5 -60 -6 -70 -7 -80 -8 -9 -90 0.1 5 1 Power Supply (V) 10 100 Frequency (MHz) 0.035 14 V+ = 5 V 12 0.030 10 0.025 THD + Noise (%) ICC (nA) 1K Figure 8. Frequency Response Figure 7. Logic Threshold vs Power Supply 8 6 V+ = 3 V 0.020 0.015 4 0.010 2 0.005 0 0 -40 -20 0 20 40 60 80 Temperature (C) Figure 9. Power-Supply Current vs Temperature 12 -3 Crosstalk -40 Loss - dB 2.5 100 10 100 1K 10K 100K Frequency (MHz) Figure 10. Total Harmonic Distortion (THD) vs Frequency W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 PIN DESCRIPTION PIN NUMBER NAME 1 NO 2 GND 3 NC 4 COM 5 V+ Power supply 6 IN Digital control pin to connect COM terminal to NO or NC terminals DESCRIPTION Normally-open terminal Digital ground Normally-closed terminal Common terminal PARAMETER DESCRIPTION SYMBOL DESCRIPTION VCOM Voltage at COM VNC Voltage at NC VNO Voltage at NO ron Resistance between COM and NC or COM and NO ports, when the channel is ON rpeak Peak ON-state resistance over a specified voltage range ron Difference of ron between channels ron(flat) Difference between the maximum and minimum value of ron in a channel over the specified range of conditions INC(OFF) Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state under worst-case input and output conditions INO(OFF) Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state under worst-case input and output conditions INC(ON) Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output (COM) being open INO(ON) Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output (COM) being open ICOM(ON) Leakage current measured at the COM port, with the corresponding channel (COM to NO or COM to NC) in the ON state and the output (NC or NO) being open VIH Minimum input voltage for logic high for the control input (IN) VIL Minimum input voltage for logic low for the control input (IN) VIN Voltage at IN IIH, IIL Leakage current measured at IN tON Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay between the digital control (IN) signal and analog outputs (COM, NC, or NO) signal, when the switch is turning ON. tOFF Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay between the digital control (IN) signal and analog outputs (COM, NC, or NO) signal, when the switch is turning OFF. tBBM Break-before-make time. This parameter is measured under the specified range of conditions and by the propagation delay between the output of two adjacent analog channels (NC and NO), when the control signal changes state. QC Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NC, NO, or COM) output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input. Charge injection, QC = CL x VO, CL is the load capacitance, and VO is the change in analog output voltage. 13 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 PARAMETER DESCRIPTION (continued) SYMBOL DESCRIPTION CNC(OFF) Capacitance at the NC port when the corresponding channel (NC to COM) is OFF CNO(OFF) Capacitance at the NO port when the corresponding channel (NO to COM) is OFF CNC(ON) Capacitance at the NC port when the corresponding channel (NC to COM) is ON CNO(ON) Capacitance at the NO port when the corresponding channel (NO to COM) is ON CCOM(ON) Capacitance at the COM port when the corresponding channel (COM to NC or COM to NO) is ON CIN Capacitance of IN OISO OFF isolation of the switch is a measurement OFF-state switch impedance. This is measured in dB in a specific frequency, with the corresponding channel (NC to COM or NO to COM) in the OFF state. XTALK Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NC to NO or NO to NC). This is measured in a specific frequency and in dB. BW Bandwidth of the switch. This is the frequency in which the gain of an ON channel is -3 dB below the DC gain. I+ Static power-supply current with the control (IN) pin at V+ or GND I+ This is the increase in I+ for each control (IN) input that is at the specified voltage, rather than at V+ or GND. 14 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 PARAMETER MEASUREMENT INFORMATION V+ VNC NC COM + VCOM Channel ON VNO NO r on + VI ICOM IN VCOM * VNO or VNC W I COM VI = VIH or VIL + GND Figure 11. ON-State Resistance (ron) V+ VNC NC COM + VCOM OFF-State Leakage Current Channel OFF VI = VIH or VIL VNO NO VI IN + GND Figure 12. OFF-State Leakage Current (INC(OFF), INO(OFF)) V+ VNC NC + COM VNO NO VI VCOM ON-State Leakage Current Channel ON VI = VIH or VIL NOTE: See electrical characteristics for test conditions. IN + GND Figure 13. ON-State Leakage Current (ICOM(ON), INC(ON), INO(ON)) 15 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 V+ VCOM COM Capacitance Meter VBIAS VNC NC VNO NO VI IN VBIAS = V+ or GND VI = VIH or VIL Capacitance is measured at NC, NO, COM, and IN inputs during ON and OFF conditions. GND Figure 14. Capacitance (CI, CCOM(ON), CNC(OFF), CNO(OFF), CNC(ON), CNO(ON)) V+ NC or NO VNC or VNO VCOM VI TEST RL CL VCOM tON 50 35 pF V+ tOFF 50 35 pF V+ COM CL(2) NC or NO RL IN CL(2) Logic Input(1) RL GND V+ Logic Input (VI) 50% 50% 0 tON tOFF Switch Output (VNC or VNO) 90% 90% (1) All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr < 5 ns, tf < 5 ns. (2) CL includes probe and jig capacitance. Figure 15. Turn-On (tON) and Turn-Off Time (tOFF) V+ Logic Input (VI) VNC or VNO NC or NO VCOM V+ 50% 0 COM NC or NO CL(2) VI Logic Input(1) IN RL Switch Output (VCOM) 90% 90% tBBM GND VNC or VNO = V+/2 RL = 50 CL = 35 pF (1) All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr < 5 ns, tf < 5 ns. (2) CL includes probe and jig capacitance. Figure 16. Break-Before-Make Time (tBBM) 16 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 V+ Network Analyzer 50 W VNC NC Channel ON: NC to COM COM Source Signal VCOM VI = VIH or VIL NO Network Analyzer Setup VI 50 W IN Source Power = 0 dBM (632-mV P-P at 50-W load) + GND DC Bias = 350 mV Figure 17. Bandwidth (BW) V+ Network Analyzer Channel OFF: NC to COM 50 W VNC NC VI = VIH or VIL COM Source Signal 50 W VCOM NO Network Analyzer Setup VI 50 W Source Power = 0 dBM (632-mV P-P at 50-W load) IN + GND DC Bias = 350 mV Figure 18. OFF Isolation (OISO) V+ Network Analyzer 50 W Channel ON: NC to COM VNC Channel OFF: NO to COM NC VCOM Source Signal VNO 50 W VI + VI = VIH or VIL NO 50 W IN GND Network Analyzer Setup Source Power = 0 dBM (632-mV P-P at 50-W load) DC Bias = 350 mV Figure 19. Crosstalk (XTALK) 17 W www.ti.com SCDS174B - AUGUST 2004 - REVISED MAY 2005 V+ RGEN VGEN OFF ON OFF V IL NC or NO COM + VIH Logic Input (VI) VCOM VCOM VCOM NC or NO CL(2) VI VGEN = 0 to V+ RGEN = 0 CL = 0.1 nF QC = CL x VCOM VI = VIH or VIL IN Logic Input(1) GND (1) All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr < 5 ns, tf < 5 ns. (2) CL includes probe and jig capacitance. Figure 20. Charge Injection (QC) Channel ON: COM to NC VSOURCE = V+ P-P VI = VIH or VIL fSOURCE = 600 Hz to 20 kHz RL = 600 CL = 50 pF V+/2 V+ RL 10 mF VO COM NO VSOURCE RL VI CL(1) IN + GND (1) CL includes probe and jig capacitance. Figure 21. Total Harmonic Distortion (THD) 18 10 mF NC Analyzer PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TS5A3159DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DBVTE4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKR ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKRG4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKT ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKTE4 ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5A3159DCKTG4 ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2008 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TS5A3159 : * Enhanced Product: TS5A3159-EP NOTE: Qualified Version Definitions: * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ TS5A3159DBVR SOT-23 3000 180.0 9.2 DBV 6 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.17 3.23 1.37 4.0 8.0 Q3 TS5A3159DBVT SOT-23 DBV 6 250 180.0 9.2 3.17 3.23 1.37 4.0 8.0 Q3 TS5A3159DCKR SC70 DCK 6 3000 180.0 9.2 2.3 2.55 1.2 4.0 8.0 Q3 TS5A3159DCKT SC70 DCK 6 250 180.0 9.2 2.3 2.55 1.2 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TS5A3159DBVR SOT-23 DBV 6 3000 205.0 200.0 33.0 TS5A3159DBVT SOT-23 DBV 6 250 205.0 200.0 33.0 TS5A3159DCKR SC70 DCK 6 3000 205.0 200.0 33.0 TS5A3159DCKT SC70 DCK 6 250 205.0 200.0 33.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated