C2260A1-0103 TCXO
VECTRON
INTERNATIONAL
www.vectron.com
49-07268-801-281 fax
49-07268-801-0 tel
Germany
D-74924 Neckarbischofsheim
Landstrasse
Vectron International GmbH & Co. KG modified 2008-02-05 Index : 15 printed 2008-08-20 • page 1 of 5
Vectron International • Product Specifications
Nominal frequency (f0) 20 MHz
Frequency stabilities
Parameter Frequency stability Operating temp. range
Over all (df/f0) -4.6 to 4.6 ppm
vs. operating temp. range (df/f@25 °C) -0.28 to 0.28 ppm -40 ... 85 °C
Parameter Value Condition
initial tolerance (df/f0) -1 to 1 ppm @25 °C
vs. supply voltage change (df/f) -0.2 to 0.2 ppm static; 3.3 V ±5 %
vs. load change (df/f) -0.2 to 0.2 ppm static; Load ± 10 %
aging first year <± 0.8 ppm
vs. aging / 15 years (df/f) <± 2.5 ppm @ 40 °C
Holdover 24 h ± 0.32 ppm incl. temp. stab. and supply
voltage
total freq. stab.: <±4,6ppm for all causes @ 20 years aging meet GR1244
RF output
Parameter Value Condition
Signal LVCMOS
Load 15 pF ±10 %
Fan out 3
Rise Time < 5 ns @ 10 to 90 %Vout
Fall Time < 5 ns @ 90 to 10 %Vout
Duty cycle 45 / 55 % @ 1.65 V
V Lo
w
x < 0.33 V
V High x > 2.97 V
Sub Harmonics <- 80 dBc
Spurious <- 80 dBc
Enable function Enable Function output
Pin 1 Pin 3
high data
open data
low high tristate
Supply voltage
Parameter Value Condition
Supply voltage (Vs) 3.3 V ± 5 %
Current consumption steady state < 15 mA @ Vsnom & 25 °C
Additional Parameters
Parameter Value Condition
Phase Noise < -85 dBc/Hz 10 Hz max
< -110 dBc/Hz 100 Hz values
< -125 dBc/Hz 1000 Hz
< -135 dBc/Hz 10 kHz
< -145 dBc/Hz 100 kHz
Short term stability <± 1000.0 E-12 1 sec
Start-up time < 10 ms
A
dditional information
24 hour drift: ±0.04ppm
Processing & Packing handling &processing note
Additional environmental conditions
Tensile strength of leads
DIN IEC 68 T2-21 (Ua 1)
Flexibility of leads
DIN IEC 68 T2-21 (Ub)
Sealing test A
nicht dicht (not hermetically sealed)
C2260A1-0103 TCXO
VECTRON
INTERNATIONAL
www.vectron.com
49-07268-801-281 fax
49-07268-801-0 tel
Germany
D-74924 Neckarbischofsheim
Landstrasse
Vectron International GmbH & Co. KG modified 2008-02-05 Index : 15 printed 2008-08-20 • page 2 of 5
Vectron International • Product Specifications
Additional environmental conditions
Solderability
DIN IEC 68 T2-20 (Ta)
100% RoHS compliant
Solvent resistance
EN 60068-2-45, Test xA
washable device
Absolute Maximum Ratings
Parameter Min Typ Max Units Condition
Operable temperature range -40 85 °C
Storage temperature range -55 105 °C
C2260A1-0103 TCXO
VECTRON
INTERNATIONAL
www.vectron.com
49-07268-801-281 fax
49-07268-801-0 tel
Germany
D-74924 Neckarbischofsheim
Landstrasse
Vectron International GmbH & Co. KG modified 2008-02-05 Index : 15 printed 2008-08-20 • page 3 of 5
Vectron International • Product Specifications
Enclosure
Type G211A Height 2.3 mm
all units in mm
Pin Connections
Pin 1: Enable
Pin 2: GND (Case)
Pin 3: RF-Output
Pin 4: Vs (supply voltage)
Marking
2A-103
20M000
*VAYYWW
-
-
* pin-1 marking
C2260A1-0103 TCXO
VECTRON
INTERNATIONAL
www.vectron.com
49-07268-801-281 fax
49-07268-801-0 tel
Germany
D-74924 Neckarbischofsheim
Landstrasse
Vectron International GmbH & Co. KG modified 2008-02-05 Index : 15 printed 2008-08-20 • page 4 of 5
Vectron International • Product Specifications
Reflow profile
Profile Feature Pb-Free Assembly/Sn-Pb Assembly
Average ramp-up rate (TL to Tp) 3°C/second max.
Preheat -Temperature Min (Tsmin) 150°c
-Temperature Min (Tsmax) 200°c
-Time (min to max) (ts) 60-180 seconds
Tsmax to TL - Ramp-up Rate 3°C/second max.
Time maintainted above - Temperature (T L) 217°C
- Time (tL) 60-150 seconds
Peak Temperature (Tp) max 260°C
Time within 5°C of actual Peak Temperature (tp) 20-40 seconds
Ramp-down Rate 6°C/second max.
Time 25°C to Peak Temperature 8 minutes max.
Note: All temperatures refer to topside of the package, measured on the package body surface.
A
dditional Information
This SMD oscillator has been designed for pick and place reflow soldering.
C2260A1-0103 TCXO
VECTRON
INTERNATIONAL
www.vectron.com
49-07268-801-281 fax
49-07268-801-0 tel
Germany
D-74924 Neckarbischofsheim
Landstrasse
Vectron International GmbH & Co. KG modified 2008-02-05 Index : 15 printed 2008-08-20 • page 5 of 5
Vectron International • Product Specifications
Standard shipping method
Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm]
16 125 750 8 5.4 7.4 2.7
Notes:
Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage,
frequency control voltage, load, temperature (25°C).
Subject to technical modification.
