www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION ( V) Preliminary Specifications ( ) Final Specifications Module 10.4 Inch Color TFT-LCD Model Name G104SN03 V5 Customer Date Approved by Debbie Chiu Checked & Approved by Date 2011/04/25 /2 01 1/ 7/ 19 Prepared by 2011/04/25 al General Display Business Division / AU Optronics corporation AU O C on f id e nt ia lF or FO R TE C In te rn Note: This Specification is subject to change without notice. U se O nl y ShengHsun Lin G104SN03 V5 rev.0.0 1/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION Contents 1. Operating Precautions.....................................................................................4 2. General Description .........................................................................................5 2.1 Display Characteristics...........................................................................................................5 2.2 Optical Characteristics ...........................................................................................................6 3. Functional Block Diagram ...............................................................................9 4. Absolute Maximum Ratings ..........................................................................10 4.1 Absolute Ratings of TFT LCD Module .................................................................................10 4.2 Absolute Ratings of Environment ........................................................................................10 5. Electrical Characteristics ..............................................................................11 5.1 TFT LCD Module .................................................................................................................. 11 5.2 Backlight Unit........................................................................................................................13 6. Signal Characteristic .....................................................................................14 7/ 19 6.1 Pixel Format Image ..............................................................................................................14 6.2 Scanning Direction ...............................................................................................................14 6.3 Signal Description ................................................................................................................15 6.4 The Input Data Format .........................................................................................................16 6.5 Interface Timing ....................................................................................................................17 6.6 Power ON/OFF Sequence ...................................................................................................18 01 1/ 7. Connector & Pin Assignment ........................................................................19 O nl y /2 7.1 TFT LCD Module: LVDS Connector.....................................................................................19 7.2 LED Backlight Unit (CN2): Driver Connector ......................................................................19 7.3 LED Backlight Unit (CN4): Light bar Connector..................................................................20 al U se 8. Reliability Test Criteria ..................................................................................21 9. Mechanical Characteristics ...........................................................................22 In te rn 9.1 LCM Outline Dimension (Front View) ..................................................................................22 9.2 LCM Outline Dimension (Rear View)...................................................................................23 TE C 10. Label and Packaging....................................................................................24 FO R 10.1 Shipping Label (on the rear side of TFT-LCD display) ......................................................24 10.2 Carton Package .................................................................................................................24 or 11 Safety.............................................................................................................25 AU O C on f id e nt ia lF 11.1 Sharp Edge Requirements.................................................................................................25 11.2 Materials .............................................................................................................................25 11.3 Capacitors...........................................................................................................................25 11.4 National Test Lab Requirement..........................................................................................25 G104SN03 V5 rev.0.0 2/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION Record of Revision Version and Date All First draft specification New Description - O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 April 25, 2011 Old description AU 0.0 Page G104SN03 V5 rev.0.0 3/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 1. Operating Precautions 19 7/ 1/ 01 /2 y nl O U se al te rn In C TE FO R or lF ia nt 15) 16) id e 13) 14) on f 12) C 11) O 10) Since front polarizer is easily damaged, please be cautious and not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input connector. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. When the panel surface is soiled, wipe it with absorbent cotton or soft cloth. Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard surface. To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling TFT-LCD Module. Do not open nor modify the module assembly. Do not press the reflector sheet at the back of the module to any direction. In case if a module has to be put back into the packing container slot after it was taken out from the container, do not press the center of the LED light bar edge. Instead, press at the far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged. At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very short time. Please design your display product well to avoid external force applying to module by end-user directly. Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. Severe temperature condition may result in different luminance, response time and lamp ignition voltage. Continuous operating TFT-LCD display under low temperature environment may accelerate lamp exhaustion and reduce luminance dramatically. The data on this specification sheet is applicable when LCD module is placed in landscape position. Continuous displaying fixed pattern may induce image sticking. It's recommended to use screen saver or shuffle content periodically if fixed pattern is displayed on the screen. AU 1) 2) 3) 4) 5) 6) 7) 8) 9) G104SN03 V5 rev.0.0 4/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 2. General Description This specification applies to the Color Active Matrix Liquid Crystal Display G104SN03 V5 composed of a TFT-LCD display, a driver and power supply circuit, and a LED backlight system. The screen format is intended to support SVGA (800(H) x 600(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits). LED driving board for backlight unit is included in G104SN03 V5 and the LED unit is replaceable. All input signals are LVDS interface and compatible with G104SN03 V1. G104SN03 V5 designed with wide viewing angle; wide temperature and long life LED backlight (30k hrs) is well suited for industial applications. G104SN03 V5 is a RoHS product. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 oC condition: Items Unit Specifications Active Area [mm] 211.2(H) x 158.4(V) Screen Diagonal [inch] 10.4 Pixels H x V 800x3(RGB) x 600 [mm] 0.264 x 0.264 19 Pixel Pitch R.G.B. Vertical Stripe Display Mode TN, Normally White /2 01 1/ 7/ Pixel Arrangement [Volt] 3.3 (typ.) Typical Power Consumption [Watt] 2.5W(ILED=25mA) All black pattern Weight [Grams] [mm] C In Electrical Interface 236.0(H)x 176.9(V) x 5.7(D) (typ.) 1 channel LVDS FO R 16.2M / 262K colors [oC] o [ C] -20 to +70 -20 to +70 RoHS Compliance AU O C on f id e nt ia lF or Support Color 300g(typ.) Anti-glare, Hardness 3H TE Surface Treatment RoHS Compliance O U se al te rn Physical Size Temperature Range Operating Storage (Non-Operating) nl y Nominal Input Voltage VDD G104SN03 V5 rev.0.0 5/25 www.DataSheet4U.net 1 ith50cm ingdstace w vew Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 oC (Room Temperature): Item Unit Conditions Min. Typ. Max. ILED= 25mA 190 230 White Luminance [cd/m2] (center point) 5 points % [msec] Response Time Rising [msec] [msec] Viewing Angle Rising + Falling 25 30 - 10 20 - 35 - Horizontal CR = 10 (Right) (Left) 60 TBD [degree] [degree] Vertical CR = 10 (Upper) (Lower) 55 TBD - TBD TBD TBD TBD TBD 60 TBD 45 Red x TBD TBD Green x TBD TBD Green y TBD Blue x TBD TBD Blue y TBD TBD 01 1/ 0.28 TBD White y /2 0.30 0.33 50 2,3 4 5 - 6 - TBD TBD TBD TBD 0.34 0.36 - O nl y % 0.31 1 50 [degree] [degree] White x Color Gamut 500 - Red y Color / Chromaticity Coordinates (CIE 1931) - 400 - Falling 75 19 Contrast Ratio 65 7/ Uniformity Note U se Note 1: Measurement method Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent) In < 1 lux FO R TE Environment Center C Test Point te rn al Aperture or LCD Module C on f id e nt ia lF equivalent Measuring distance Module Driving Equipment AU O SR_3 or G104SN03 V5 rev.0.0 6/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION Note 2: Definition of 5 points position (Display active area: 211.2mm (H) x 158.4mm (V)) W W /4 W /4 W /4 W /4 H /4 1 2 H /4 3 H H /4 4 5 H /4 Note 3: The luminance uniformity of 5 points is defined by dividing the minimum luminance values by the maximum test point luminance Minimum Brightness of five points W9 = Maximum Brightness of five points 19 Note 4: Definition of contrast ratio (CR): 7/ Brightness on the "White" state 1/ Contrast ratio (CR)= /2 01 Brightness on the "Black" state O nl y Note 5: Definition of response time: U se The output signals of photo detector are measured when the input signals are changed from "White" to "Black" Tf Tr TE C In % te rn 90% of amplitudes. Please refer to the figure as below. al (falling time) and from "Black" to "White" (rising time), respectively. The response time interval is between 10% and White lF or Optical FO R 100 90 Black White 10 0 AU O C on f id e nt ia response G104SN03 V5 rev.0.0 7/25 www.DataSheet4U.net aurentofcrastio10,ahescrnte,ovra180hoizntald180 ngleisthm Product Specification G104SN03 V5 AU OPTRONICS CORPORATION Note 6: Definition of viewing angle Viewing a vertical range (off-normal viewing angles). The 180 viewing angle range is broken down as below: 90 () horizontal left and right, and 90 () vertical high (up) and low (down). The measurement direction is typically perpendicular to the AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 display surface with the screen rotated to its center to develop the desired measurement viewing angle. G104SN03 V5 rev.0.0 8/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 3. Functional Block Diagram The following diagram shows the functional block of the 10.4 inch color TFT/LCD module: Timing Controller Connecter 6/8 bits Sel DPS DC Power Panel Controller Gate Driver IC LVDS receiver LVDS 1ch DC/DC converter TFT-LCD 800x(3)x600 Pixels Source Driver IC RSDS Generate Gamma Voltage Light Bar AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 DC Power G104SN03 V5 rev.0.0 9/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 4. Absolute Maximum Ratings 4.1 Absolute Ratings of TFT LCD Module Item Symbol Min Max Unit Logic/LCD drive Voltage Vin -0.3 +4.0 [Volt] 4.2 Absolute Ratings of Environment Item Symbol Min Max Unit Operation Humidity HOP 5 90 [%RH] Operating Temperature TOP Storage Temperature -20 TST Storage Humidity +70 -20 HST [oC] +70 5 [ C] o [%RH] 90 Note: Maximum Wet-Bulb should be 39 C and no condensation. AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 o G104SN03 V5 rev.0.0 10/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 5. Electrical Characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Symbol Parameter Min Typ Max Units 3.0 3.3 3.6 [Volt] VDD Logic/LCD Drive Voltage IDD VDD Current - 320 - [mA] Irush LCD Inrush Current - - 1.5 [A] PDD VDD Power - 1.06 - [Watt] - 100 [mV] p-p VDDrp Allowable Logic/LCD Drive Ripple Voltage - Remark All Black Pattern (VDD=3.3V, at 60Hz) Note 1 All Black Pattern (VDD=3.3V, at 60Hz) All Black Pattern (VDD=3.3V, at 60Hz) Note 1: Measurement condition: +3.3V D6 D5 D2 D1 Q3 AO6402 19 y S /2 01 Q3 AO6402 G SW MAG-SPST VR1 1 R2 0.01uF/25V 47K al 1K U se O nl C3 +12.0V 2 1/ D1 D2 D5 D6 R2 (LCD Module Input) 7/ C1 1uF/16V 1K SW1 VDD VCC G R1 47K (High to Low) Control Signal F1 S 3.3V 90% ia nt 10% 0.47ms+ 10% VDD rising time AU O C on f id e 0V lF or FO R TE C In te rn C2 1uF/25V G104SN03 V5 rev.0.0 11/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Symbol Item Min. Typ. Max. Unit Remark VTH Differential Input High Threshold - - 100 [mV] VCM=1.2V VTL Differential Input Low Threshold 100 - - [mV] VCM=1.2V Input Differential Voltage 100 400 600 [mV] 1.125 1.25 1.375 [V] VID Differential Input Common Mode Voltage VICM VTH/VTL=+-100mV AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 Note: LVDS Signal Waveform. G104SN03 V5 rev.0.0 12/25 www.DataSheet4U.net Product Specification (R o ) G104SN03 V5 AU OPTRONICS CORPORATION 5.2 Backlight Unit 5.2.1 Parameter guideline for LED Following characteristics are measured under a stable condition using an inverter at 25 om Temperature): Symbol Parameter Min. Typ. Max. VCC Input Voltage 10.8 12 12.6 IVCC Input Current - 0.12 - PVCC Power Consumption - 1.44 - FPWM Dimming Frequency 200 - 10K Dimming Swing Voltage 3 3.3 5.5 Dimming duty cycle 5 - 100 % Dimming Voltage 0.6 3 [Volt] Dimming Range 30 100 % IF LED Forward Current - 25 - [mA] Ta = 25oC VF LED Forward Voltage - 26 29.2 [Volt] IF = 25mA, Ta = 25oC Operation Life 1.92 - 25,000 30,000 - 100% Blightness [Hz] PWM Dimming [Volt] [Watt] Analoge Dimming IF = 25mA, Ta = 25oC LED total Power Ta= 60oC RH<60% Hrs IF=25mA Tj<70 C o /2 Note 1: Ta means ambient temperature of TFT-LCD module. [Watt] 19 - 100% Blightness 7/ LED Power Consumption [A] 1/ PLED Remark [Volt] 01 Dimming Unit nl y Note 2: VCC, IVCC, Irush LED, PVCC are defined for LED backlight.(100% duty of PWM dimming) O Note 3: IF, VF are defined for one channel LED. There are three LED channel in back light unit. U se Note 4: If G104SN03 V5 module is driven by high current or at high ambient temperature & humidity condition. The al operating life will be reduced. te rn Note 5: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated AU O C on f id e nt ia lF or FO R TE C In data. G104SN03 V5 rev.0.0 13/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 6. Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format. 1st 2nd Line 600th R G B R G B R G B R G B Pixel R G B R G B R G B R G B /2 01 1/ Lin 800th Pixel 19 1st Pixel 7/ Pixel 799th O nl y 6.2 Scanning Direction or FO R TE C In te rn al U se The following figures show the image seen from the front view. The arrow indicates the direction of scan. Fig. 2 Reverse scan (Pin4, DPS = High) AU O C on f id e nt ia lF Fig. 1 Normal scan (Pin4, DPS = Low or NC) G104SN03 V5 rev.0.0 14/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 6.3 Signal Description The module uses a LVDS receiver embedded in AUO's ASIC. LVDS is a differential signal technology for LCD interface and a high-speed data transfer device. (1)Input signal interface Pin no Symbol 1 VDD 3 GND 2 +3.3 V power supply VDD 4 6 Ground Reverse Scan Function [H: Enable; L/NC:Disable] RxIN0- LVDS receiver signal channel 0 GND Ground LVDS Differential Data Input (R0, R1, R2, R3, R4, R5, G0) RxIN0+ 7 8 9 RxIN1- LVDS receiver signal channel 1 GND Ground LVDS Differential Data Input (G1, G2, G3, G4, G5, B0, B1) RxIN1+ 10 11 RxIN2- LVDS receiver signal channel 2 13 GND Ground LVDS Differential Data Input (B2, B3, B4, B5, HS, VS, DE) RxIN2+ CKIN- 16 GND Ground RxIN3- /2 LVDS Differential Data Input (R6, R7, G6, G7, B6, B7, RSV) SEL68 6/8 bits LVDS input setting [H: 8 bits; L/NC:6 bits] 20 Reserved for AUO internal test. Please treat it as NC. O Reserved U se 19 RxIN3+ y 18 LVDS receiver signal channel 3, NC for 6 bit LVDS Input nl 17 19 LVDS receiver signal clock CKIN+ 7/ 15 1/ 14 01 12 Etc. +3.3 V power supply DPS 5 Function te rn al Note 1: Input Signals shall be in low status when VDD is off. C AU O C on f id e nt ia lF or FO R TE Note 3: RSV means "Reserved". In Note 2: High stands for "3.3V", Low stands for "0V", NC means "No Connection". G104SN03 V5 rev.0.0 15/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 6.4 The Input Data Format SEL68 ="Low" or "NC" for 6 bits LVDS Input SEL68 = "High" for 8 bits LVDS Input NS-like format Note1: Please follow PSWG. Note2: R/G/B data 7:MSB, R/G/B data 0:LSB O C In C TE FO R or lF ia nt 19 Remark 7/ Red-pixel Data /2 01 1/ For 8Bits LVDS input MSB: R7 ; LSB: R0 al U se O nl y For 6Bits LVDS input MSB: R5 ; LSB: R0 te rn Description Red Data 7 Red Data 6 Red Data 5 Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 Green Data 7 Green Data 6 Green Data 5 Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 Blue Data 7 Blue Data 6 Blue Data 5 Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 LVDS Data Clock Data Enable Signal id e on f Signal Name R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 RxCLKIN DE Green-pixel Data For 8Bits LVDS input MSB: G7 ; LSB: G0 For 6Bits LVDS input MSB: G5 ; LSB: G0 Blue-pixel Data For 8Bits LVDS input MSB: B7 ; LSB: B0 For 6Bits LVDS input MSB: B5 ; LSB: B0 When the signal is high, the pixel data shall be valid to be displayed. AU Note: Output signals from any system shall be low or Hi-Z state when VDD is off. G104SN03 V5 rev.0.0 16/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 6.5 Interface Timing 6.5.1 Timing Characteristics Signal Symbol Clock Frequency 1/ TClock Vertical Section Horizontal Section Period TV Active TVD Blanking TVB Period TH Active THD Blanking THB Frame Rate Note : DE mode. Min. Typ. 30 Max. 40 50 608 628 1024 -- 600 -- 8 28 424 960 1056 1060 -- 800 -- 160 256 260 50 60 75 F Unit MHz TLine TClock Hz Input Timing Definition ( DE Mode) 1/ 7/ TCLOCK 19 6.5.2 Input Timing Diagram Pixel 3 Pixel N-1 nl Pixel 2 O Pixel 1 U se Invaild Data Pixel N Invaild Data Pixel 1 DE te rn al Input Data y /2 01 DOTCLK THD TH FO R TE C In THB DE TVB TV AU O C on f id e nt ia lF or TVD G104SN03 V5 rev.0.0 17/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 6.6 Power ON/OFF Sequence 1/ 7/ 19 VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. T5 10 or In nl O - [ms] U se [ms] 10 - - [ms] [ms] [ms] [ms] -- -- 10 [ms] 0 16 50 [ms] 1000 - 10 - nt -- 50 - T12 T13 [ms] - 110 T11 10 -- Units 0 T10 id e on f C TE FO R 10 ia T9 -- 0.5 lF T8 - Max. al 200 T7 C 40 T3 T4 O 30 0.5 T2 AU Typ. te rn T1 Min. y Value Parameter T6 /2 01 Power ON/OFF sequence timing - -- - -- 10 - [ms] [ms] [ms] [ms] The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. G104SN03 V5 rev.0.0 18/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 7. Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT LCD Module: LVDS Connector Connector Name / Designation Signal Connector Connector Model Number MSB24013P20HA or compatible Manufacturer STM or compatible Adaptable Plug P24013P20 or compatible Pin No. Symbol Pin No. Symbol 3 GND 4 DPS 1 VDD 2 VDD 5 RxIN0- 6 RxIN0+ 9 RxIN1+ 10 GND 13 GND 14 RxCKIN- 18 RxIN3+ GND 12 15 RxCKIN+ 16 19 RSV 20 RxIN3- GND SEL68 /2 01 17 RxIN2+ 19 RxIN2- RxIN1- 7/ 11 8 1/ 7 Connector Name / Designation Lamp Connector Entery te rn al Manufacturer Connector Model Number 3808K-F05N-02R or compatible C Pin2 GND lF nt ia On/OFF Dimming id e Pin4 NA 12V input GND 5V-ON,0V-OFF PWM/Analog AU O C on f Pin5 Description or VCC TE Symbol FO R Pin No. Pin3 H208K-P05N-02B or compatible In Mating Model Number Pin1 U se O nl y 7.2 LED Backlight Unit (CN2): Driver Connector G104SN03 V5 rev.0.0 19/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 7.3 LED Backlight Unit (CN4): Light bar Connector Connector Name / Designation Lamp Connector Manufacturer Entery or compatible Connector Model Number Entery H203K-D04N-02Bor compatible Mating Model Number Entery 3800K-F04N-03Ror compatible Symbol Cable color Signal Name 1 AN RED LED anode 2 CA1 BLACK LED Cathode 1 3 CA2 WHITE LED Cathode 2 4 CA3 BLUE LED Cathode 3 AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl y /2 01 1/ 7/ 19 Pin # G104SN03 V5 rev.0.0 20/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 8. Reliability Test Criteria Items Temperature Humidity Bias High Temperature Operation Low Temperature Operation Hot Storage Required Condition Note 40 oC /90%,300Hr 70 C, 300Hr (center point of panel surface) o -20 oC, 300Hr 70 C, 300 hours o Cold Storage -20 C, 300 hours o Thermal Shock Test Hot Start Test Cold Start Test Shock Test (Non-Operating) -20 oC /30 min ,60 oC /30 min ,100cycles, 40 oC minimun ramp rate 70 oC /1 Hr min. -20 C /1 Hr min. o power on/off per 5 minutes, 5 times power on/off per 5 minutes, 5 times 50G,20ms,Half-sine wave,(+-X,+-Y,+-Z) Vibration Test (Non-Operating) 1.5G, 10~200~10Hz, Sine wave On/off test On/10 sec, Off/10 sec, 30,000 cycles 30mins/axis, 3 direction (X, Y, Z) 7/ 19 Contact : 8KV/ operation, Class B ESD Note 1 01 1/ Air : 15KV / operation, Class B 30-230 MHz, limit 40 dBu V/m, 230-1000 MHz, limit 47 dBu V/m /2 EMI Note2: O al te rn In The reliability test is performed only to examine the TFT-LCD module capability. To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24 hours at least in advance. AU O C on f id e nt ia lF or test. C Each test is done by new TFT-LCD module. Don't use the same TFT-LCD module repeatedly for reliability TE Water condensation is not allowed for each test items. FO R Self-recoverable. No hardware failures. U se . nl y Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost G104SN03 V5 rev.0.0 21/25 on f C or lF ia nt id e C TE FO R al te rn In O Dimension (Front View) 9.1 LCM Outline U 9. Mechanical Characteristics A U se y nl O AU OPTRONICS CORPORATION 19 7/ 1/ 01 /2 Product Specification G104SN03 V5 22/25 G104SN03 V5 rev.0.0 www.DataSheet4U.net O U on f C or lF ia nt id e C TE FO R al te rn In 9.2 LCM Outline Dimension (Rear View) A U se y nl O AU OPTRONICS CORPORATION 19 7/ 1/ 01 /2 Product Specification G104SN03 V5 23/25 G104SN03 V5 rev.0.0 www.DataSheet4U.net www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 10. Label and Packaging 10.1 Shipping Label (on the rear side of TFT-LCD display) V5 10.2 Carton Package /2 01 1/ 7/ 19 LCD Module al te rn Carton AU O C on f id e nt ia lF or FO R TE C In NOTE : 1. Max. Capacity : 30 LCD Modules/Carton. 2. Max. Weight : 13Kg/Carton. 3. Meas : 448 mm*402mm*350mm. EPP Cushion U se O nl y Anti-Static Bag G104SN03 V5 rev.0.0 24/25 www.DataSheet4U.net Product Specification G104SN03 V5 AU OPTRONICS CORPORATION 11 Safety 11.1 Sharp Edge Requirements There will be no sharp edges or comers on the display assembly that could cause injury. 11.2 Materials 11.2.1 Toxicity There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist. 11.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 11.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from 7/ 19 being inserted backwards. /2 y The display module will satisfy all requirements for compliance to: 01 1/ 11.4 National Test Lab Requirement U.S.A. Information Technology Equipment AU O C on f id e nt ia lF or FO R TE C In te rn al U se O nl UL 60950-1 second edition G104SN03 V5 rev.0.0 25/25