PM/P/P Cores Halves/EP Cores and Accessories Series/Type: B65843 The following products presented in this data sheet are being withdrawn. Ordering Code B65843A0000Y066 Substitute Product Date of Withdrawal 2020-08-14 Deadline Last Orders 2020-11-13 Last Shipments 2021-02-12 Please contact your nearest TDK sales office if you need support in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.tdk-electronics.tdk.com/sales. EP 13 Core B65843A To IEC 62317-5 For transformers featuring high inductance and low overall height For power applications Delivery mode: sets Magnetic characteristics (per set) l/A le Ae Amin Ve = 1.24 mm-1 = 24.2 mm = 19.5 mm2 = 14.9 mm2 = 472 mm3 Approx. weight 4.5 g/set Gapped (AL values/air gaps examples) e Ordering code nH s approx. mm T38 63 3% 100 3% 160 4% 200 4% 250 5% 315 6% 400 7% 0.39 0.24 0.15 0.12 0.10 0.08 0.06 62 99 158 198 247 311 395 B65843A0063A038 B65843A0100A038 B65843A0160B038 B65843A0200B038 B65843A0250J038 B65843A0315C038 B65843A0400E038 T57 63 3% 100 3% 160 4% 200 4% 250 5% 315 6% 400 7% 0.38 0.24 0.15 0.12 0.09 0.07 0.06 62 99 158 198 247 311 395 B65843A0063A057 B65843A0100A057 B65843A0160B057 B65843A0200B057 B65843A0250J057 B65843A0315C057 B65843A0400E057 T66 63 3% 100 3% 160 4% 200 4% 250 5% 315 6% 400 7% 0.39 0.24 0.15 0.12 0.10 0.08 0.06 62 99 158 198 247 311 395 B65843A0063A066 B65843A0100A066 B65843A0160B066 B65843A0200B066 B65843A0250J066 B65843A0315C066 B65843A0400E066 Material AL value Please read Cautions and warnings and Important notes at the end of this document. 2 5/17 EP 13 Core B65843A Gapped e Ordering code nH s approx. mm N45 63 3% 100 3% 160 4% 200 4% 250 5% 315 6% 400 7% 0.38 0.24 0.15 0.12 0.09 0.07 0.05 62 99 158 198 247 311 395 B65843A0063A045 B65843A0100A045 B65843A0160B045 B65843A0200B045 B65843A0250J045 B65843A0315C045 B65843A0400E045 N87 63 3% 100 3% 160 4% 200 4% 250 5% 315 6% 400 7% 0.37 0.23 0.14 0.11 0.09 0.07 0.05 62 99 158 198 247 311 395 B65843A0063A087 B65843A0100A087 B65843A0160B087 B65843A0200B087 B65843A0250J087 B65843A0315C087 B65843A0400E087 Material AL value Ungapped Material AL value e nH PV Ordering code W/set N45 2400 +30/-20% 2370 B65843A0000R045 T57 2500 +30/-20% 2470 B65843A0000R057 N30 2800 +30/-20% 2765 B65843A0000R030 T65 4000 +30/-20% 3950 B65843A0000R065 T38 7000 +40/-30% 6910 B65843A0000Y038 T66 8500 +40/-30% 8400 B65843A0000Y066 N49 1000 +30/-20% 990 < 0.06 ( 50 mT, 500 kHz, 100 C) B65843A0000R049 N87 1600 +30/-20% 1580 < 0.18 (200 mT, 100 kHz, 100 C) B65843A0000R087 Other AL values/air gaps and materials available on request - see Processing remarks on page 7. Please read Cautions and warnings and Important notes at the end of this document. 3 5/17 EP 13 Accessories B65844 Coil former, squared pins Material: GFR thermosetting plastic (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 C), color code black Sumikon PM 9630 (R) [E41429 (M)], SUMITOMO BAKELITE CO LTD Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 C, 3.5 s Winding: see Processing notes, 2.1 Sections AN mm2 lN mm AR value Terminals Ordering code 1 14.3 23.8 57.1 10 B65844W1010D001 Please read Cautions and warnings and Important notes at the end of this document. 4 5/17 EP 13 Accessories B65844 Coil former with closed center flange for high-voltage applications Material: GFR thermosetting plastic (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 C), color code black Sumikon PM 9630 (R) [E41429 (M)], SUMITOMO BAKELITE CO LTD Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 C, 3.5 s Winding: see Processing notes, 2.1 Pins: Squared pins Sections AN mm2 lN mm AR value Terminals Ordering code 2 13.9 23.8 58.9 10 B65844X1010D002 Please read Cautions and warnings and Important notes at the end of this document. 5 5/17 EP 13 Accessories B65844 Mounting assembly The set comprises a yoke and a clamp Yoke Made of cold rolled steel (0.4 mm) with ground terminal (tinned) Clamp Spring clamp, made of bronze (0.3 mm) Ordering code Complete mounting assembly B65844S2000X000 Yoke Please read Cautions and warnings and Important notes at the end of this document. Clamp 6 5/17 Ferrites and accessories Cautions and warnings Cautions and warnings Mechanical stress and mounting Ferrite cores have to meet mechanical requirements during assembling and for a growing number of applications. Since ferrites are ceramic materials one has to be aware of the special behavior under mechanical load. As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast temperature changing or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads can cause cracks or failure of the ferrite cores. For detailed information see data book, chapter "General - Definitions, 8.1". Effects of core combination on AL value Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent that the initial permeability is dependent on the stress state of the core. The higher the stresses are in the core, the lower is the value for the initial permeability. Thus the embedding medium should have the greatest possible elasticity. For detailed information see data book, chapter "General - Definitions, 8.1". Heating up Ferrites can run hot during operation at higher flux densities and higher frequencies. NiZn-materials The magnetic properties of NiZn-materials can change irreversible in high magnetic fields. Ferrite Accessories EPCOS ferrite accessories have been designed and evaluated only in combination with EPCOS ferrite cores. EPCOS explicitly points out that EPCOS ferrite accessories or EPCOS ferrite cores may not be compatible with those of other manufacturers. Any such combination requires prior testing by the customer and will be at the customer`s own risk. EPCOS assumes no warranty or reliability for the combination of EPCOS ferrite accessories with cores and other accessories from any other manufacturer. Processing remarks The start of the winding process should be soft. Else the flanges may be destroyed. - Too strong winding forces may blast the flanges or squeeze the tube that the cores can not be mounted any more. - Too long soldering time at high temperature (>300 C) may effect coplanarity or pin arrangement. - Not following the processing notes for soldering of the J-leg terminals may cause solderability problems at the transformer because of pollution with Sn oxyde of the tin bath or burned insulation of the wire. For detailed information see chapter "Processing notes", section 2.2. - The dimensions of the hole arrangement have fixed values and should be understood as a recommendation for drilling the printed circuit board. For dimensioning the pins, the group of holes can only be seen under certain conditions, as they fit into the given hole arrangement. To avoid problems when mounting the transformer, the manufacturing tolerances for positioning the customers' drilling process must be considered by increasing the hole diameter. Please read Cautions and warnings and Important notes at the end of this document. 7 5/17 Ferrites and accessories Cautions and warnings Display of ordering codes for EPCOS products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of EPCOS, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes. Please read Cautions and warnings and Important notes at the end of this document. 8 5/17 Ferrites and accessories Symbols and terms Symbols and terms Symbol Meaning Unit A Ae AL AL1 Amin AN AR B B B B BDC BR BS C0 CDF DF d Ea f fcutoff fmax fmin fr fCu g H H HDC Hc h h/i 2 I IDC I J k k3 k3c L Cross section of coil Effective magnetic cross section Inductance factor; AL = L/N2 Minimum inductance at defined high saturation ( a) Minimum core cross section Winding cross section Resistance factor; AR = RCu /N2 RMS value of magnetic flux density Flux density deviation Peak value of magnetic flux density Peak value of flux density deviation DC magnetic flux density Remanent flux density Saturation magnetization Winding capacitance Core distortion factor Relative disaccommodation coefficient DF = d/i Disaccommodation coefficient Activation energy Frequency Cut-off frequency Upper frequency limit Lower frequency limit Resonance frequency Copper filling factor Air gap RMS value of magnetic field strength Peak value of magnetic field strength DC field strength Coercive field strength Hysteresis coefficient of material Relative hysteresis coefficient RMS value of current Direct current Peak value of current Polarization Boltzmann constant Third harmonic distortion Circuit third harmonic distortion Inductance mm2 mm2 nH nH mm2 mm2 = 10-6 Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT Vs/m2, mT F = As/ V mm-4.5 Please read Cautions and warnings and Important notes at the end of this document. 9 5/17 J s-1, Hz s-1, Hz s-1, Hz s-1, Hz s-1, Hz mm A/m A/m A/m A/m 10-6 cm/A 10-6 cm/A A A A Vs/m2 J/K H = Vs/A Ferrites and accessories Symbols and terms Symbol Meaning Unit L/L L0 LH Lp Lrev Ls le lN N PCu Ptrans PV PF Q R RCu Rh Rh Ri Rp Rs Rth RV s T T TC t tv tan tan L tan r tan e tan h tan /i U U Ve Z Zn Relative inductance change Inductance of coil without core Main inductance Parallel inductance Reversible inductance Series inductance Effective magnetic path length Average length of turn Number of turns Copper (winding) losses Transferrable power Relative core losses Performance factor Quality factor (Q = L/Rs = 1/tan L) Resistance Copper (winding) resistance (f = 0) Hysteresis loss resistance of a core Rh change Internal resistance Parallel loss resistance of a core Series loss resistance of a core Thermal resistance Effective loss resistance of a core Total air gap Temperature Temperature difference Curie temperature Time Pulse duty factor Loss factor Loss factor of coil (Residual) loss factor at H 0 Relative loss factor Hysteresis loss factor Relative loss factor of material at H 0 RMS value of voltage Peak value of voltage Effective magnetic volume Complex impedance Normalized impedance |Z|n = |Z| /N 2 x (le /Ae) H H H H H H mm mm Please read Cautions and warnings and Important notes at the end of this document. 10 5/17 W W mW/g K/W mm C K C s V V mm3 /mm Ferrites and accessories Symbols and terms Symbol Meaning Unit F e r B i s 0 a app e i p' p" r rev s' s" tot Temperature coefficient (TK) Relative temperature coefficient of material Temperature coefficient of effective permeability Relative permittivity Magnetic flux Efficiency of a transformer Hysteresis material constant Hysteresis core constant Magnetostriction at saturation magnetization Relative complex permeability Magnetic field constant Relative amplitude permeability Relative apparent permeability Relative effective permeability Relative initial permeability Relative real (inductive) component of (for parallel components) Relative imaginary (loss) component of (for parallel components) Relative permeability Relative reversible permeability Relative real (inductive) component of (for series components) Relative imaginary (loss) component of (for series components) Relative total permeability derived from the static magnetization curve Resistivity Magnetic form factor DC time constant Cu = L/RCu = AL/AR Angular frequency; = 2 f 1/K 1/K 1/K l/A Cu All dimensions are given in mm. Surface-mount device Please read Cautions and warnings and Important notes at the end of this document. 11 5/17 Vs mT-1 A-1H-1/2 Vs/Am m-1 mm-1 s s-1 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements ("CSR") TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdkelectronics.tdk.com/trademarks. Release 2018-10 Please read Cautions and warnings and Important notes at the end of this document. 12 5/17