ADP3120A Dual Bootstrapped, 12 V MOSFET Driver with Output Disable The ADP3120A is a single Phase 12 V MOSFET gate drivers optimized to drive the gates of both high-side and low-side power MOSFETs in a synchronous buck converter. The high-side and low-side driver is capable of driving a 3000 pF load with a 45 ns propagation delay and a 25 ns transition time. With a wide operating voltage range, high or low side MOSFET gate drive voltage can be optimized for the best efficiency. Internal adaptive nonoverlap circuitry further reduces switching losses by preventing simultaneous conduction of both MOSFETs. The floating top driver design can accommodate VBST voltages as high as 35 V, with transient voltages as high as 40 V. Both gate outputs can be driven low by applying a low logic level to the Output Disable (OD) pin. An Undervoltage Lockout function ensures that both driver outputs are low when the supply voltage is low, and a Thermal Shutdown function provides the IC with overtemperature protection. www.onsemi.com MARKING DIAGRAMS 8 8 1 1 * All-In-One Synchronous Buck Driver Bootstrapped High-Side Drive One PWM Signal Generates Both Drives Anticross Conduction Protection Circuitry OD for Disabling the Driver Outputs Meets CPU VR Requirement when Used with Patented FlexModet Controller These are Pb-Free Devices 1 A L Y W G 8 L3C ALYWG G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package PIN CONNECTIONS BST 1 8 DRVH IN OD SWN PGND VCC DRVL Applications 1 * Multiphase Desktop CPU Supplies * Single-Supply Synchronous Buck Converters 1 DFN8 MN SUFFIX CASE 506BJ Features * * * * * 3120A ALYW G SO-8 D SUFFIX CASE 751 8 BST IN DRVH SWN OD PGND VCC DRVL (Top View) ORDERING INFORMATION Device Package Shipping ADP3120AJRZ SO-8 (Pb-Free) 98 Units / Rail ADP3120AJRZ-RL SO-8 (Pb-Free) 2500 / Tape & Reel ADP3120AJCPZ-RL DFN8 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2012 August, 2018 - Rev. 5 1 Publication Order Number: ADP3120A/D ADP3120A OD 3 VCC TSD 1 BST 8 DRVH 7 SWN 4 VCC 5 DRVL 6 PGND UVLO IN 2 FALLING EDGE DELAY FALLING EDGE DELAY START STOP MONITOR MONITOR NON-OVERLAP TIMERS MIN DRVL OFF TIMER Figure 1. Block Diagram PIN DESCRIPTION SO-8 DFN8 Symbol Description 1 1 BST Upper MOSFET Floating Bootstrap Supply. A capacitor connected between BST and SW pins holds this bootstrap voltage for the high-side MOSFET as it is switched. The recommended capacitor value is between 100 nF and 1.0 mF. An external diode is required with the ADP3120A. 2 2 IN Logic-Level Input. This pin has primary control of the drive outputs. 3 3 OD Output Disable. When low, normal operation is disabled forcing DRVH and DRVL low. 4 4 VCC Input Supply. A 1.0 mF ceramic capacitor should be connected from this pin to PGND. 5 5 DRVL Output drive for the lower MOSFET. 6 6 PGND Power Ground. Should be closely connected to the source of the lower MOSFET. 7 7 SWN Switch Node. Connect to the source of the upper MOSFET. 8 8 DRVH Output drive for the upper MOSFET. www.onsemi.com 2 ADP3120A MAXIMUM RATINGS Rating Value Unit Operating Ambient Temperature, TA -20 to 85 C Operating Junction Temperature, TJ (Note 1) -20 to 150 C 45 123 C/W C/W 7.5 55 C/W C/W -65 to 150 C 260 peak C 1 - Package Thermal Resistance: SO-8 Junction-to-Case, RqJC Junction-to-Ambient, RqJA (2-Layer Board) Package Thermal Resistance: DFN8 (Note 2) Junction-to-Case, RqJC (From die to exposed pad) Junction-to-Ambient, RqJA Storage Temperature Range, TS Lead Temperature Soldering (10 sec): Reflow (SMD styles only) Pb-Free (Note 3) JEDEC Moisture Sensitivity Level SO-8 (260 peak profile) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Internally limited by thermal shutdown, 150C min. 2. 2 layer board, 1 in2 Cu, 1 oz thickness. 3. 60-180 seconds minimum above 237C. NOTE: This device is ESD sensitive. Use standard ESD precautions when handling. MAXIMUM RATINGS NOTE: Pin Symbol Pin Name VMAX VMIN VCC Main Supply Voltage Input 15 V -0.3 V PGND Ground 0V 0V BST Bootstrap Supply Voltage Input 35 V wrt/PGND 40 V < 50 ns wrt/PGND 15 V wrt/SW -0.3 V wrt/SW SW Switching Node (Bootstrap Supply Return) 35 V 40 V < 50 ns -5.0 V -10 V < 200 ns DRVH High-Side Driver Output BST + 0.3 V -0.3 V wrt/SW -2.0 V < 200 ns wrt/SW DRVL Low-Side Driver Output VCC + 0.3 V -0.3 V DC -5.0 V < 200 ns IN DRVH and DRVL Control Input 6.5 V -0.3 V OD Output Disable 6.5 V -0.3 V All voltages are with respect to PGND except where noted. www.onsemi.com 3 ADP3120A ELECTRICAL CHARACTERISTICS (Note 4) (VCC = 12 V, TA = -20C to +85C, TJ = 0C to +125C unless otherwise noted.) Characteristic Symbol Condition Min Typ Max Unit Supply Supply Voltage Range VCC - 4.6 - 13.2 V Supply Current ISYS BST = 12 V, IN = 0 V - 0.7 2.0 mA Input Voltage High VOD_HI - 2.0 - - V Input Voltage Low VOD_LO - - - 0.8 V - - 400 - mV No internal pullup or pulldown resistors -1.0 - +1.0 mA OD Input Hysteresis Input Current PWM Input Input Voltage High VPWM_HI - 2.0 - - V Input Voltage Low VPWM_LO - - - 0.8 V Hysteresis - - - 400 - mV Input Current - No internal pullup or pulldown resistors -1.0 - +1.0 mA Output Resistance, Sourcing Current - BST - SW = 12 V; TA = -20C to 85C BST - SW = 12 V; TA = 25C - 2.2 - 3.9 3.3 W Output Resistance, Sinking Current - BST - SW = 12 V; TA = -20C to 85C BST - SW = 12 V; TA = 25C - 1.0 - 2.6 1.8 W Output Resistance, Unbiased - BST - SW = 0 V - 15 - kW trDRVH tfDRVH BST - SW = 12 V, CLOAD = 3.0 nF (See Figure 3) - 20 11 40 30 ns tpdhDRVH BST - SW = 12 V, CLOAD = 3.0 nF (See Figure 3) BST - SW = 12 V, CLOAD = 3.0 nF (See Figure 3) 32 45 70 ns 25 35 20 25 35 55 High-Side Driver Transition Times Propagation Delay Times (Note 5) tpdlDRVH tpdlOD tpdhOD (See Figure 2) (See Figure 2) - SW to PGND - 15 - kW Output Resistance, Sourcing Current - TA = -20C to 85C TA = 25C - 1.8 - 3.9 3.3 W Output Resistance, Sinking Current - TA = -20C to 85C TA = 25C - 1.0 - 2.6 1.8 W Output Resistance, Unbiased - VCC = PGND - 15 - kW trDRVL tfDRVL CLOAD = 3.0 nF, (See Figure 3) - 16 11 35 30 ns tpdhDRVL CLOAD = 3.0 nF, (See Figure 3) (Note 6, tpdhDRVL only) - 12 35 ns 15 45 20 20 35 35 SW Pulldown Resitance Low-Side Driver Transition Times Propagation Delay Times (Note 5) tpdlDRVL tpdlOD tpdhOD (See Figure 2) (See Figure 2) - DRVH - SW = 0 - 85 - ns UVLO Startup - - 3.9 4.3 4.5 V UVLO Shutdown - - 3.7 4.1 4.3 V Hysteresis - - 0.1 0.2 0.4 V Timeout Delay Undervoltage Lockout 4. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC). 5. For propagation delays, "tpdh" refers to the specified signal going high; "tpdl" refers to it going low. 6. Guaranteed by design; not tested in production. www.onsemi.com 4 ADP3120A APPLICATIONS INFORMATION Theory of Operation Likewise, when the PWM input pin goes low, DRVH will go low after the propagation delay (tpdDRVH). The time to turn off the high-side MOSFET (tfDRVH) is dependent on the total gate charge of the high-side MOSFET. A timer will be triggered once the high-side mosfet has stopped conducting, to delay (tpdhDRVL) the turn on of the low-side MOSFET The ADP3120A are single phase MOSFET drivers designed for driving two N-channel MOSFETs in a synchronous buck converter topology. The ADP3120A will operate from 5.0 V or 12 V, but have been optimized for high current multi-phase buck regulators that convert 12 V rail directly to the core voltage required by complex logic chips. A single PWM input signal is all that is required to properly drive the high-side and the low-side MOSFETs. Each driver is capable of driving a 3 nF load at frequencies up to 1 MHz. Power Supply Decoupling The ADP3120A can source and sink relatively large currents to the gate pins of the external MOSFETs. In order to maintain a constant and stable supply voltage (VCC) a low ESR capacitor should be placed near the power and ground pins. A 1 mF to 4.7 mF multi layer ceramic capacitor (MLCC) is usually sufficient. Low-Side Driver The low-side driver is designed to drive a ground-referenced low RDS(on) N-Channel MOSFET. The voltage rail for the low-side driver is internally connected to the VCC supply and PGND. Input Pins High-Side Driver The PWM input and the Output Disable pins of the ADP3120A have internal protection for Electro Static Discharge (ESD), but in normal operation they present a relatively high input impedance. If the PWM controller does not have internal pulldown resistors, they should be added externally to ensure that the driver outputs do not go high before the controller has reached its under voltage lockout threshold. The NCP5381 controller does include a passive internal pulldown resistor on the drive-on output pin. The high-side driver is designed to drive a floating low RDS(on) N-channel MOSFET. The gate voltage for the high side driver is developed by a bootstrap circuit referenced to Switch Node (SW) pin. The bootstrap circuit is comprised of an external diode, and an external bootstrap capacitor. When the ADP3120A are starting up, the SW pin is at ground, so the bootstrap capacitor will charge up to VCC through the bootstrap diode See Figure 4. When the PWM input goes high, the high-side driver will begin to turn on the high-side MOSFET using the stored charge of the bootstrap capacitor. As the high-side MOSFET turns on, the SW pin will rise. When the high-side MOSFET is fully on, the switch node will be at 12 V, and the BST pin will be at 12 V plus the charge of the bootstrap capacitor (approaching 24 V). The bootstrap capacitor is recharged when the switch node goes low during the next cycle. Bootstrap Circuit The bootstrap circuit uses a charge storage capacitor (CBST) and the internal (or an external) diode. Selection of these components can be done after the high-side MOSFET has been chosen. The bootstrap capacitor must have a voltage rating that is able to withstand twice the maximum supply voltage. A minimum 50 V rating is recommended. The capacitance is determined using the following equation: CBST + Safety Timer and Overlap Protection Circuit It is very important that MOSFETs in a synchronous buck regulator do not both conduct at the same time. Excessive shoot-through or cross conduction can damage the MOSFETs, and even a small amount of cross conduction will cause a decrease in the power conversion efficiency. The ADP3120A prevent cross conduction by monitoring the status of the external mosfets and applying the appropriate amount of "dead-time" or the time between the turn off of one MOSFET and the turn on of the other MOSFET. When the PWM input pin goes high, DRVL will go low after a propagation delay (tpdlDRVL). The time it takes for the low-side MOSFET to turn off (tfDRVL) is dependent on the total charge on the low-side MOSFET gate. The ADP3120A monitor the gate voltage of both MOSFETs and the switchnode voltage to determine the conduction status of the MOSFETs. Once the low-side MOSFET is turned off an internal timer will delay (tpdhDRVH) the turn on of the high-side MOSFET QGATE DVBST where QGATE is the total gate charge of the high-side MOSFET, and DVBST is the voltage droop allowed on the high-side MOSFET drive. For example, a NTD60N03 has a total gate charge of about 30 nC. For an allowed droop of 300 mV, the required bootstrap capacitance is 100 nF. A good quality ceramic capacitor should be used. The bootstrap diode must be rated to withstand the maximum supply voltage plus any peak ringing voltages that may be present on SW. The average forward current can be estimated by: IF(AVG) + QGATE fMAX where fMAX is the maximum switching frequency of the controller. The peak surge current rating should be checked in-circuit, since this is dependent on the source impedance of the 12 V supply and the ESR of CBST. www.onsemi.com 5 ADP3120A OD VOD_HI VOD_LO tpdlOD tpdhOD 90% DRVH or DRVL 10% Figure 2. Output Disable Timing Diagram VPWM_HI VPWM_LO IN tpdlDRVL DRVL tfDRVL 90% 90% 2V 10% 10% tpdhDRVH trDRVH tpdlDRVH 90% trDRVL tfDRVH 90% DRVH-SW 2V 10% 10% tpdhDRVL SW Figure 3. Nonoverlap Timing Diagram 12 V 12 V ADP3120A 4 Output Enable PWM in BST DRVH 3 SW OD DRVL 2 IN PGND Vcc 1 8 7 5 6 Vout Figure 4. ADP3120A Example Circuit www.onsemi.com 6 ADP3120A PACKAGE DIMENSIONS DFN8 3x3, 0.5P CASE 506BJ ISSUE O PIN 1 REFERENCE 2X 0.10 C 2X CCC CCC CCC CCC 0.10 C EDGE OF PACKAGE A B D NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. L L1 DETAIL A E OPTIONAL CONSTRUCTION DIM A A1 A3 b D D2 E E2 e K L L1 L TOP VIEW DETAIL A OPTIONAL CONSTRUCTION DETAIL B 0.05 C A 8X 0.05 C (A3) NOTE 4 SIDE VIEW A1 D2 8X L 1 C 1.85 EXPOSED Cu E2 8X SOLDERMASK DEFINED MOUNTING FOOTPRINT SEATING PLANE DETAIL A 4 K EE EE DETAIL B 8 5 8X 8X 0.35 MOLD CMPD OPTIONAL CONSTRUCTION e MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 1.64 1.84 3.00 BSC 1.35 1.55 0.50 BSC 0.20 --- 0.30 0.50 0.00 0.03 3.30 1.55 0.63 0.50 PITCH b 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 8X DIMENSION: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 ADP3120A PACKAGE DIMENSIONS SOIC-8 D SUFFIX CASE 751-07 ISSUE AK NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. -X- A 8 5 S B 0.25 (0.010) Y M M 1 4 K -Y- G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H M D 0.25 (0.010) M Z Y S X J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. FlexMode is a trademark of Analog Devices, Inc. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ADP3120A/D