DE1-127D0FN-N20N - EATON - Datasheet.Live

05/06/2015 174331 - HPL-ED2015 V12.0 EN 1 / 5

Speed�starters,�single-phase�power�supply�connection,�three-phase

motor�connection�at�230�V,�7�A�and�1,�5�kW�/�2�HP

Part�no. DE1-127D0FN-N20N

Article�no. 174331

Catalog�No. DE1-127D0FN-N20N

Delivery�programme

Product range   PowerXL™ DE1 Speed Starters

Rated operational voltage Ue 230 V AC, 1-phase

Output voltage with V<sub>e</sub> U2 230 V AC, 3-phase

Mains voltage (50/60Hz) ULN V 200 (-10%) - 240 (+10%)

Rated�operational�current   

At 150% overload IeA 7

Note   Rated operational current at an operating frequency of 16 kHz and an ambient air

temperature of +50°C

Note   Overload cycle for 60 s every 600 s

Assigned�motor�rating   

Note   for normal internally and externally ventilated 4 pole, three-phase asynchronous

motors with 1500 rpm-1 at 50 Hz or 1800 min-1 at 60 Hz

Note   Overload cycle for 60 s every 600 s

Note   at 230 V, 50 Hz

150 % Overload P kW 1.5

150 % Overload IeA 6.3

Note   at 220 - 240 V, 60 Hz

150 % Overload P HP 2

150 % Overload IeA 6.8

Degree of Protection   IP20/NEMA 0

Interface/field bus (built-in)   OP-Bus (RS485)/Modbus RTU

Fitted with   Radio interference suppression filter

Frame size   FS1

Connection to SmartWire-DT   with SmartWire-DT module DX-NET-SWD3

Technical�data

General

Standards   Specification for general requirements: IEC/EN 61800-2

EMC requirements: IEC/EN 61800-3

Safety requirements: IEC/EN 61800-5-1

Certifications   CE, UL, cUL, c-Tick

Production quality   RoHS, ISO 9001

Climatic proofing ρw% < 95%, average relative humidity (RH), non-condensing, non-corrosive (EN50178)

Ambient temperature  °C 

operation (150 % overload) ϑ °C -10 - +50, max. +60

Storage ϑ °C -40 - +70

Radio interference level   

Radio interference class (EMC)   C1, C2, C3, depending on the motor cable length, the connected load, and ambient

conditions. External radio interference suppression filters (optional) may be

necessary.

Environment (EMC)   1st and 2nd environments

maximum motor cable length I m C1 ≤ 5 m

C2 ≤ 10 m

C3 ≤ 25 m

Mechanical shock resistance  g 15 (11 m/s, EN 60068-2-27)

05/06/2015 174331 - HPL-ED2015 V12.0 EN 2 / 5

Vibration   EN 61800-5-1

Altitude  m 0 - 1000 m above sea level

above 1000m with 1 % performance reduction per 100m

max. 2000 m

Degree of Protection   IP20/NEMA 0

Protection against direct contact   BGV A3 (VBG4, finger- and back-of-hand proof)

Main�circuit

Supply   

Rated operational voltage Ue 230 V AC, 1-phase

Mains voltage (50/60Hz) ULN V 200 (-10%) - 240 (+10%)

Input current (150% overload) ILN A 17.4

Supply frequency fLN Hz 50/60

Frequency range fLN Hz 45 - 66

Mains switch-on frequency   Maximum of one time every 30 seconds

Power section   

Overload current (150% overload) ILA 10.5

max. starting current (High Overload) IH% 200

Note about max. starting current   for 1.875 seconds every 600 seconds

Output voltage with VeU2 230 V AC, 3-phase

Output Frequency f2Hz 0 - 50/60 (max. 300)

Switching frequency fPWM kHz 16

adjustable 4 - 32 (audible)

Operation Mode   U/f control

Speed control with slip compensation

Frequency resolution (setpoint value) Δf Hz 0.025

Rated operational current   

At 150% overload IeA 7

Note   Rated operational current at an operating frequency of 16 kHz and an ambient air

temperature of +50°C

Maximum leakage current to ground (PE) without motor IPE mA < 3,5 AC, < 10 DC

Fitted with   Radio interference suppression filter

Frame size   FS1

Motor feeder   

Note   for normal internally and externally ventilated 4 pole, three-phase asynchronous

motors with 1500 rpm-1 at 50 Hz or 1800 min-1 at 60 Hz

Note   Overload cycle for 60 s every 600 s

Note   at 230 V, 50 Hz

150 % Overload P kW 1.5

Note   at 220 - 240 V, 60 Hz

150 % Overload P HP 2

Apparent power   

Apparent power at rated operation 230 V S kVA 2.79

Apparent power at rated operation 240 V S kVA 2.91

Braking function   

Standard braking torque   max. 30 % MN

DC braking torque   100 %, adjustable

Control�section

Reference voltage UsV 10 V DC (max. 0.2 mA)

Analog inputs   1, parameterizable, 0 - 10 V DC, 0/4 - 20 mA

Digital inputs   4, parameterizable, 10 - 30 V DC

Relay outputs   1, parameterizable, N/O, 6 A (250 V, AC-1) / 5 A (30 V, DC-1)

Interface/field bus (built-in)   OP-Bus (RS485)/Modbus RTU

Assigned�switching�and�protective�elements

Power Wiring   

Safety device (fuse or miniature circuit-breaker)   

IEC (Typ B, gG)   FAZ-B20/1N

UL (Class CC or J)  A 20

05/06/2015 174331 - HPL-ED2015 V12.0 EN 3 / 5

Mains contactor   

150 % overload (CT/IH, at 50 °C)   DILEM-… + P1DILEM

DILEM-…+P1DILEM

110 % overload (VT/IL, at 40 °C)   DILM7-… + DILM12-XP1

Main choke   

150 % overload (CT/IH, at 50 °C)   DX-LN1-018

Radio interference suppression filter (external)   DX-EMC12-019-FS1

Note regarding radio interference suppression filter   Optional external radio interference suppression filter for longer motor cable

lengths and for use in different EMC environments

Motor feeder   

motor choke   

150 % overload (CT/IH, at 50 °C)   DX-LM3-008

Sine filter   

150 % overload (CT/IH, at 50 °C)   DX-SIN3-010

Design�verification�as�per�IEC/EN�61439

Technical data for design verification   

Rated operational current for specified heat dissipation InA 7

Equipment heat dissipation, current-dependent Pvid W 59

Operating ambient temperature min.  °C -10

Operating ambient temperature max.  °C 50

IEC/EN 61439 design verification   

10.2 Strength of materials and parts   

10.2.2 Corrosion resistance   Meets the product standard's requirements.

10.2.3.1 Verification of thermal stability of enclosures   Meets the product standard's requirements.

10.2.3.2 Verification of resistance of insulating materials to normal heat   Meets the product standard's requirements.

10.2.3.3 Verification of resistance of insulating materials to abnormal heat

and fire due to internal electric effects

  Meets the product standard's requirements.

10.2.4 Resistance to ultra-violet (UV) radiation   Meets the product standard's requirements.

10.2.5 Lifting   Does not apply, since the entire switchgear needs to be evaluated.

10.2.6 Mechanical impact   Does not apply, since the entire switchgear needs to be evaluated.

10.2.7 Inscriptions   Meets the product standard's requirements.

10.3 Degree of protection of ASSEMBLIES   Does not apply, since the entire switchgear needs to be evaluated.

10.4 Clearances and creepage distances   Meets the product standard's requirements.

10.5 Protection against electric shock   Does not apply, since the entire switchgear needs to be evaluated.

10.6 Incorporation of switching devices and components   Does not apply, since the entire switchgear needs to be evaluated.

10.7 Internal electrical circuits and connections   Is the panel builder's responsibility.

10.8 Connections for external conductors   Is the panel builder's responsibility.

10.9 Insulation properties   

10.9.2 Power-frequency electric strength   Is the panel builder's responsibility.

10.9.3 Impulse withstand voltage   Is the panel builder's responsibility.

10.9.4 Testing of enclosures made of insulating material   Is the panel builder's responsibility.

10.10 Temperature rise   The panel builder is responsible for the temperature rise calculation. Eaton will

provide heat dissipation data for the devices.

10.11 Short-circuit rating   Is the panel builder's responsibility. The specifications for the switchgear must be

observed.

10.12 Electromagnetic compatibility   Is the panel builder's responsibility. The specifications for the switchgear must be

observed.

10.13 Mechanical function   The device meets the requirements, provided the information in the instruction

leaflet (IL) is observed.

Technical�data�ETIM�5.0

Low-voltage industrial components (EG000017) / Frequency controller =< 1 kV (EC001857)

Electric engineering, automation, process control engineering / Electrical drive / Static frequency converter / Static frequency converter = < 1 kv (ecl@ss8-27-02-31-01 [AKE177010])

Mains voltage  V 200 - 240

Mains frequency   50/60 Hz

Number of phases input   1

Number of phases output   3

05/06/2015 174331 - HPL-ED2015 V12.0 EN 4 / 5

Max. output frequency  Hz 300

Rated output voltage  V 230

Measuring output current  A 7

Output power at rated output voltage  kW 0.5

Max. output at quadratic load at rated output voltage  kW 0.5

Max. output at linear load at rated output voltage  kW 0.5

With control unit   No

Application in industrial area permitted   Yes

Application in domestic- and commercial area permitted   Yes

Supporting protocol for TCP/IP   No

Supporting protocol for PROFIBUS   No

Supporting protocol for CAN   No

Supporting protocol for INTERBUS   No

Supporting protocol for ASI   No

Supporting protocol for KNX   No

Supporting protocol for MODBUS   Yes

Supporting protocol for Data-Highway   No

Supporting protocol for DeviceNet   No

Supporting protocol for SUCONET   No

Supporting protocol for LON   No

Supporting protocol for PROFINET IO   No

Supporting protocol for PROFINET CBA   No

Supporting protocol for SERCOS   No

Supporting protocol for Foundation Fieldbus   No

Supporting protocol for EtherNet/IP   No

Supporting protocol for AS-Interface Safety at Work   No

Supporting protocol for DeviceNet Safety   No

Supporting protocol for INTERBUS-Safety   No

Supporting protocol for PROFIsafe   No

Supporting protocol for SafetyBUS p   No

Supporting protocol for other bus systems   Yes

Number of HW-interfaces industrial Ethernet   0

Number of HW-interfaces PROFINET   0

Number of HW-interfaces RS-232   0

Number of HW-interfaces RS-422   0

Number of HW-interfaces RS-485   1

Number of HW-interfaces serial TTY   0

Number of HW-interfaces USB   0

Number of HW-interfaces parallel   0

Number of HW-interfaces other   0

With optical interface   No

With PC connection   Yes

Integrated braking resistance   No

4-quadrant operation possible   No

Type of converter   U converter

Degree of protection (IP)   IP20

Height  mm 230

Width  mm 45

Depth  mm 168

Relative symmetric net frequency tolerance  % 5

Relative symmetric net current tolerance  % 10

Approvals

Product Standards   UL 508C; CSA-C22.2 No. 14; IEC/EN61800-3; IEC/EN61800-5; CE marking

UL File No.   E172143

05/06/2015 Eaton Industries GmbH

http://www.eaton.eu

174331 - HPL-ED2015 V12.0 EN

5 / 5

UL Category Control No.   NMMS, NMMS7

CSA File No.   UL report applies to both US and Canada

North America Certification   UL listed, certified by UL for use in Canada

Specially designed for North America   No

Suitable for   Branch circuits

Max. Voltage Rating   1~ 240 V AC IEC: TN-S UL/CSA: "Y" (Solidly Grounded Wey)

Degree of Protection   IEC: IP20

Dimensions

Additional�product�information�(links)

IL040005ZU�Variable�frequency�drives�DE1

IL040005ZU Variable frequency drives DE1 ftp://ftp.moeller.net/DOCUMENTATION/AWA_INSTRUCTIONS/IL040005ZU2014_07.pdf

MN040011�DE1�Variable�speed�starter,�Manual

MN040011 Drehzahlstarter DE1, Handbuch -

Deutsch

ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_DE.pdf

MN040011 DE1 Variable speed starter, Manual

- English

ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_EN.pdf

MN040011 Démarreur à vitesse variable DE1,

manuel d'utilisation - français

ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_FR.pdf

MN040011 Avviatore a velocità variabile DE1,

Manuale - italiano

ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_IT.pdf

MN040011 DE1 Variable speed starter, Manual ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_NO.pdf

MN040011 Rozrusznik silnikowy z regulacją

prędkości DE1, podręcznik - polski

ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_PL.pdf

MN040011 DE1 Variable speed starter, Manual ftp://ftp.moeller.net/DOCUMENTATION/AWB_MANUALS/MN040011_RO.pdf