LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 LM4866 2.2W Stereo Audio Amplifier Check for Samples: LM4866 FEATURES DESCRIPTION * * * * * The LM4866 is a bridge-connected (BTL) stereo audio power amplifier which, when connected to a 5V supply, delivers 2.2W to a 4 load or 2.5W to a 3 load with less than 1.0% THD+N (see Notes below). 1 2 Stereo BTL Amplifier Mode "Click and Pop" Suppression Circuitry Unity-Gain Stable Thermal Shutdown Protection Circuitry TSSOP and Exposed-DAP WQFN Packages KEY SPECIFICATIONS * * * PO at 1% THD+N - LM4866LQ, 3 load: 2.5W(typ) - LM4866LQ, 4 load: 2.2W(typ) - LM4866MTE, 3 load: 2.5W(typ) - LM4866MTE, 4 load: 2.2W(typ) - LM4866MTE, 8 load: 1.1W(typ) - LM4866MT, 8 load: 1.1W(typ) Shutdown current: 0.7A(typ) Supply voltage range: 2.0V to 5.5V APPLICATIONS * * * Multimedia Monitors Portable and Desktop Computers Portable Televisions With the LM4866 packaged in the WQFN, the customer benefits include low thermal impedance, low profile, and small size. This package minimizes PCB area and maximizes output power. The LM4866 features an externally controlled, lowpower consumption shutdown mode, and thermal shutdown protection. It also utilizes circuitry to reduce "clicks and pops" during device turn-on. Boomer audio power amplifiers are designed specifically to use few external components and provide high quality output power in a surface mount package. Note: An LM4866PWP or LM4866NHW that has been properly mounted to a circuit board will deliver 2.2W into 4. The other package options for the LM4866 will deliver 1.1W into 8. See the Application Information sections for further information concerning the LM4866PWP and LM4866NHW. Note: An LM4866PWP or LM4866NHW that has been properly mounted to a circuit board will deliver 2.5W into 3. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2001-2013, Texas Instruments Incorporated LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Typical Application Note: Pin out shown for WQFN package. Refer to the Connection Diagrams for the pinout of the TSSOP package. Connection Diagrams Top View Figure 1. TSSOP Package See Package Number PW0020A 2 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Top View Figure 2. Exposed-DAP WQFN Package See Package Number NHW0024A Top View Figure 3. Exposed-DAP TSSOP Package See Package Number PWP0020A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 3 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Absolute Maximum Ratings (1) (2) Supply Voltage 6.0V -65C to +150C Storage Temperature -0.3V to VDD +0.3V Input Voltage Power Dissipation (3) Internally limited (4) 2000V ESD Susceptibility ESD Susceptibility (5) 200V Junction Temperature 150C Solder Information Small Outline Package Vapor Phase (60 sec.) Infrared (15 sec.) Thermal Resistance (1) (2) (3) (4) (5) (6) (7) (8) (9) JC (typ)--PW0020A 215C 220C 20C/W JA (typ)--PW0020A 80C/W JC (typ)--NHW0024A 3.0C/W JA (typ)--NHW0024A 42C/W (6) JC (typ)--PWP0020A 2C/W JA (typ)--PWP0020A 41C/W (7) JA (typ)--PWP0020A 51C/W (8) JA (typ)--PWP0020A 90C/W (9) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The maximum power dissipation is dictated by TJMAX, JA, and the ambient temperature TA and must be derated at elevated temperatures. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/JA. For the LM4866, TJMAX = 150C. For the JAs for different packages, please see the Application Information section or the Absolute Maximum Ratings section. Human body model, 100pF discharged through a 1.5k resistor. Machine model, 220pF-240pF discharged through all pins. The given JA is for an LM4866 packaged in an NHW0024A with the exposed-DAP soldered to an exposed 2in2 area of 1oz printed circuit board copper. The given JA is for an LM4866 packaged in an PWP0020A with the exposed-DAP soldered to an exposed 2in2 area of 1oz printed circuit board copper. The given JA is for an LM4866 packaged in an PWP0020A with the exposed-DAP soldered to an exposed 1in2 area of 1oz printed circuit board copper. The given JA is for an LM4866 packaged in an PWP0020A with the exposed-DAP not soldered to prinbted circuit board copper. Operating Ratings Temperature Range TMIN TA TMAX -40C TA 85C Supply Voltage 2.0V VDD 5.5V 4 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Electrical Characteristics for Entire IC (1) (2) The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25C. Parameter VDD Test Conditions LM4866 Typical (3) Limit (4) Supply Voltage Units (Limits) 2 V (min) 5.5 V (max) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A (5) 11.5 20 6 mA (max) mA (min) ISD Shutdown Current VDD applied to the SHUTDOWN pin 0.7 2 A (max) (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the ground (GND) pins unless otherwise specified. Typicals are measured at 25C and represent the parametric norm. Datasheet min/max specification limits are specified by design, test, or statistical analysis. The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. Electrical Characteristics for Bridged-Mode Operation (1) (2) The following specifications apply for VDD= 5V unless otherwise specified. Limits apply for TA= 25C. Parameter VOS Output Offset Voltage PO Output Power (5) Test Conditions VIN = 0V THD+N = 1%, f = 1kHz LM4866 Typical (3) 5 Limit (4) 50 Units (Limits) mV (max) (6) LM4866PWP, RL = 3 2.5 W LM4866NHW, RL = 3 2.5 W LM4866PWP, RL = 4 2.2 W LM4866NHW, RL = 4 2.2 LM4866PW, RL = 8 1.1 W 1.0 W (min) THD+N = 10%, f = 1kHz THD+N Total Harmonic Distortion+Noise LM4866PWP, RL = 3 3.2 W LM4866NHW, RL = 3 3.2 W LM4866PWP, RL = 4 2.7 W LM4866NHW, RL = 4 2.7 W LM4866PW, RL = 8 1.5 W 20Hz f 20kHz, AVD = 2 LM4866PWP, RL = 4, PO = 2W LM4866NHW, RL = 4, PO = 2W LM4866PW, RL = 4, PO = 1W LM4866PW, RL = 8, PO = 1W 0.3 0.3 0.3 0.3 % PSRR Power Supply Rejection Ratio VDD = 5V, VRIPPLE = 200mVRMS, RL = 8, CB = 1.0F 67 dB XTALK Channel Separation f = 1kHz, CB = 1.0F 90 dB SNR Signal To Noise Ratio VDD = 5V, PO = 1.1W, RL = 8 98 dB (1) (2) (3) (4) (5) (6) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the ground (GND) pins unless otherwise specified. Typicals are measured at 25C and represent the parametric norm. Datasheet min/max specification limits are specified by design, test, or statistical analysis. Output power is measured at the device terminals. When driving 3 or 4 loads and operating on a 5V supply, the LM4866NHW and LM4866PWP must be mounted to a circuit board that has a minimum of 2.5in2 of exposed, uninterrupted copper area connected to the package's exposed DAP. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 5 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics NHW Specific Characteristics LM4866NHW THD+N vs Output Power LM4866NHW THD+N vs Frequency Figure 4. Figure 5. LM4866NHW THD+N vs Output Power LM4866NHW THD+N vs Frequency Figure 6. Figure 7. LM4866NHW Power Dissipation vs Power Output LM4866NHW Power Derating Curve Figure 8. 6 This curve shows the LM4866NHW's thermal dissipation ability at different ambient temperatures given this condition: The WQFN package's DAP is soldered to a 2.5in2, 1oz. copper plane. Figure 9. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Typical Performance Characteristics PWP Specific Characteristics LM4866PWP THD+N vs Output Power LM4866PWP THD+N vs Frequency Figure 10. Figure 11. LM4866PWP THD+N vs Output Power LM4866PWP THD+N vs Frequency Figure 12. Figure 13. LM4866PWP Power Dissipation vs Power Output LM4866PWP Power Derating Curve Figure 14. This curve shows the LM4866PWP's thermal dissipation ability at different ambient temperatures given these conditions: 500LFPM + JEDEC board: The part is soldered to a 1S2P 20-lead exposed-DAP TSSOP test board with 500 linear feet per minute of forced-air flow across it. Board information - copper dimensions: 74x74mm, copper coverage: 100% (buried layer) and 12% (top/bottom layers), 16 vias under the exposed-DAP. 500LFPM + 2.5in2: The part is soldered to a 2.5in2, 1 oz. copper plane with 500 linear feet per minute of forced-air flow across it. 2.5in2: The part is soldered to a 2.5in2, 1oz. copper plane. ot Attached: The part is not soldered down and is not forced-air cooled. Figure 15. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 7 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics 8 THD+N vs Frequency THD+N vs Output Power Figure 16. Figure 17. THD+N vs Output Power THD+N vs Frequency Figure 18. Figure 19. THD+N vs Output Power THD+N vs Frequency Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Output Power vs Supply Voltage Output Power vs Load Resistance Figure 22. Figure 23. Power Dissipation vs Output Power Dropout Voltage vs Supply Voltage Figure 24. Figure 25. Power Derating Curve Noise Floor Figure 26. Figure 27. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 9 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) 10 Channel Separation Power Supply Rejection Ratio Figure 28. Figure 29. Open Loop Frequency Response Supply Current vs Supply Voltage Figure 30. Figure 31. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 External Components Description snas1371209 (Refer to Typical Application) Components Functional Description 1. Ri The Inverting input resistance, along with Rf, set the closed-loop gain. Ri, along with Ci, form a high pass filter with fc = 1/(2RiCi). 2. Ci The input coupling capacitor blocks DC voltage at the amplifier's input terminals. Ci, along with Ri, create a highpass filter with fc = 1/(2RiCi). Refer to the section, SELECTING PROPER EXTERNAL COMPONENTS, for an explanation of determining the value of Ci. 3. Rf The feedback resistance, along with Ri, set the closed-loop gain. 4. Cs The supply bypass capacitor. Refer to the POWER SUPPLY BYPASSING section for information about properly placing, and selecting the value of, this capacitor. 5. CB The capacitor, CB, filters the half-supply voltage present on the BYPASS pin. Refer to the SELECTING PROPER EXTERNAL COMPONENTS section for information concerning proper placement and selecting CB's value. APPLICATION INFORMATION EXPOSED-DAP PACKAGE (WQFN) PCB MOUNTING CONSIDERATIONS The LM4866's exposed-DAP (die attach paddle) packages (PWP and NHW) provide a low thermal resistance between the die and the PCB to which the part is mounted and soldered. This allows rapid heat transfer from the die to the surrounding PCB copper traces, ground plane and, finally, surrounding air. The result is a low voltage audio power amplifier that produces 2.2W at 1% THD with a 4 load. This high power is achieved through careful consideration of necessary thermal design. Failing to optimize thermal design may compromise the LM4866's high power performance and activate unwanted, though necessary, thermal shutdown protection. The PWP and NHW packages must have their DAPs soldered to a copper pad on the PCB. The DAP's PCB copper pad is connected to a large plane of continuous unbroken copper. This plane forms a thermal mass and heat sink and radiation area. Place the heat sink area on either outside plane in the case of a two-sided PCB, or on an inner layer of a board with more than two layers. Connect the DAP copper pad to the inner layer or backside copper heat sink area with 32(4x8) (PWP) or 6(3x2) (NHW) vias. The via diameter should be 0.012in 0.013in with a 1.27mm pitch. Ensure efficient thermal conductivity by plating-through and solder-filling the vias. Best thermal performance is achieved with the largest practical copper heat sink area. If the heatsink and amplifier share the same PCB layer, a nominal 2.5in2 (min) area is necessary for 5V operation with a 4 load. Heatsink areas not placed on the same PCB layer as the LM4866 should be 5in2 (min) for the same supply voltage and load resistance. The last two area recommendations apply for 25c ambient temperature. Increase the area to compensate for ambient temperatures above 25c. In systems using cooling fans, the LM4866PWP can take advantage of forced air cooling. With an air flow rate of 450 linear-feet per minute and a 2.5in2 exposed copper or 5.0in2 inner layer copper plane heatsink, the LM4866PWP can continuously drive a 3 load to full power. The LM4866NHW achieves the same output power level without forced air cooling. In all circumstances and conditions, the junction temperature must be held below 150C to prevent activating the LM4866's thermal shutdown protection. The LM4866's power de-rating curve in the Typical Performance Characteristics shows the maximum power dissipation versus temperature. Example PCB layouts for the exposed-DAP TSSOP and WQFN packages are shown in the RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT section. Further detailed and specific information concerning PCB layout, fabrication, and mounting an WQFN package is available from TI's AN-1187 (Literature Number SNOA401). PCB LAYOUT AND SUPPLY REGULATION CONSIDERATIONS FOR DRIVING 3 AND 4 LOADS Power dissipated by a load is a function of the voltage swing across the load and the load's impedance. As load impedance decreases, load dissipation becomes increasingly dependent on the interconnect (PCB trace and wire) resistance between the amplifier output pins and the load's connections. Residual trace resistance causes a voltage drop, which results in power dissipated in the trace and not in the load as desired. For example, 0.1 trace resistance reduces the output power dissipated by a 4 load from 2.1W to 2.0W. This problem of decreased load dissipation is exacerbated as load impedance decreases. Therefore, to maintain the highest load dissipation and widest output voltage swing, PCB traces that connect the output pins to a load must be as wide as possible. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 11 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Poor power supply regulation adversely affects maximum output power. A poorly regulated supply's output voltage decreases with increasing load current. Reduced supply voltage causes decreased headroom, output signal clipping, and reduced output power. Even with tightly regulated supplies, trace resistance creates the same effects as poor supply regulation. Therefore, making the power supply traces as wide as possible helps maintain full output voltage swing. * Refer to the section SELECTING PROPER EXTERNAL COMPONENTS, for a detailed discussion of CB size. Pin out shown for the WQFN package. Refer to the Connection Diagrams for the pinout of the TSSOP package. Figure 32. Typical Audio Amplifier Application Circuit BRIDGE CONFIGURATION EXPLANATION As shown in Figure 32, the LM4866 consists of two pairs of operational amplifiers, forming a two-channel (channel A and channel B) stereo amplifier. (Though the following discusses channel A, it applies equally to channel B.) External resistors Rf and Ri set the closed-loop gain of AmpA1, whereas two internal 20k resistors set AmpA2's gain at -1. The LM4866 drives a load, such as a speaker, connected between the two amplifier outputs, -OUTA and +OUTA. Figure 32 shows that AmpA1's output serves as AmpA2's input. This results in both amplifiers producing signals identical in magnitude, but 180 out of phase. Taking advantage of this phase difference, a load is placed between -OUTA and +OUTA and driven differentially (commonly referred to as "bridge mode"). This results in a differential gain of AVD = 2 x (Rf / Ri) (1) Bridge mode amplifiers are different from single-ended amplifiers that drive loads connected between a single amplifier's output and ground. For a given supply voltage, bridge mode has a distinct advantage over the singleended configuration: its differential output doubles the voltage swing across the load. This produces four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or that the output signal is not clipped. To ensure minimum output signal clipping when choosing an amplifier's closed-loop gain, refer to the Audio Power Amplifier Design section. Another advantage of the differential bridge output is no net DC voltage across the load. This is accomplished by biasing channel A's and channel B's outputs at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a single-ended configuration forces a single-supply amplifier's half-supply bias voltage across the load. This increases internal IC power dissipation and may permanently damage loads such as speakers. 12 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 POWER DISSIPATION Power dissipation is a major concern when designing a successful single-ended or bridged amplifier. Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load PDMAX = (VDD)2 / (22 RL) Single-Ended (2) However, a direct consequence of the increased power delivered to the load by a bridge amplifier is higher internal power dissipation for the same conditions. The LM4866 has two operational amplifiers per channel. The maximum internal power dissipation per channel operating in the bridge mode is four times that of a single-ended amplifier. From Equation 3, assuming a 5V power supply and an 4 load, the maximum single channel power dissipation is 1.27W or 2.54W for stereo operation. PDMAX = 4 x (VDD)2 / (22 RL) Bridge Mode (3) The LM4973's power dissipation is twice that given by Equation 2 or Equation 3 when operating in the singleended mode or bridge mode, respectively. Twice the maximum power dissipation point given by Equation 3 must not exceed the power dissipation given by Equation 4: PDMAX' = (TJMAX - TA) / JA (4) The LM4866's TJMAX = 150C. In the NHW (WQFN) package soldered to a DAP pad that expands to a copper area of 5in2 on a PCB, the LM4866's JA is 20C/W. In the PWP package soldered to a DAP pad that expands to a copper area of 2in2 on a PCB , the LM4866's JA is 41C/W. At any given ambient temperature TJ\A, use Equation 4 to find the maximum internal power dissipation supported by the IC packaging. Rearranging Equation 4 and substituting PDMAX for PDMAX' results in Equation 5. This equation gives the maximum ambient temperature that still allows maximum stereo power dissipation without violating the LM4866's maximum junction temperature. TA = TJMAX - 2 x PDMAX JA (5) For a typical application with a 5V power supply and an 4 load, the maximum ambient temperature that allows maximum stereo power dissipation without exceeding the maximum junction temperature is approximately 99C for the WQFN package and 45C for the PWP package. TJMAX = PDMAX JA + TA (6) Equation 6 gives the maximum junction temperature TJMAX. If the result violates the LM4866's 150C, reduce the maximum junction temperature by reducing the power supply voltage or increasing the load resistance. Further allowance should be made for increased ambient temperatures. The above examples assume that a device is a surface mount part operating around the maximum power dissipation point. Since internal power dissipation is a function of output power, higher ambient temperatures are allowed as output power or duty cycle decreases. If the result of Equation 2 is greater than that of Equation 3, then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. If these measures are insufficient, a heat sink can be added to reduce JA. The heat sink can be created using additional copper area around the package, with connections to the ground pin(s), supply pin and amplifier output pins. External, solder attached SMT heatsinks such as the Thermalloy 7106D can also improve power dissipation. When adding a heat sink, the JA is the sum of JC, CS, and SA. (JC is the junction-to-case thermal impedance, CS is the case-to-sink thermal impedance, and SAis the sink-to-ambient thermal impedance.) Refer to the Typical Performance Characteristics curves for power dissipation information at lower output power levels. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a 5V regulator typically use a 10F in parallel with a 0.1F filter capacitors to stabilize the regulator's output, reduce noise on the supply line, and improve the supply's transient response. However, their presence does not eliminate the need for a local 1.0F tantalum bypass capacitance connected between the LM4866's supply pins and ground. Do not substitute a ceramic capacitor for the tantalum. Doing so may cause oscillation in the output signal. Keep the length of leads and traces that connect capacitors between the LM4866's power supply pin and ground as short as possible. Connecting a 1F capacitor, CB, between the Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 13 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com BYPASS pin and ground improves the internal bias voltage's stability and improves the amplifier's PSRR. The PSRR improvements increase as the bypass pin capacitor value increases. Too large, however, increases turnon time and can compromise amplifier's click and pop performance. The selection of bypass capacitor values, especially CB, depends on desired PSRR requirements, click and pop performance (as explained in the section, SELECTING PROPER EXTERNAL COMPONENTS), system cost, and size constraints. MICRO-POWER SHUTDOWN The voltage applied to the SHUTDOWN pin controls the LM4866's shutdown function. Activate micro-power shutdown by applying VDD to the SHUTDOWN pin. When active, the LM4866's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The logic threshold is typically VDD/2. The low 0.7A typical shutdown current is achieved by applying a voltage that is as near as VDD as possible to the SHUTDOWN pin. A voltage thrat is less than VDD may increase the shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 10k pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier operation by closing the switch. Opening the switch connects the SHUTDOWN pin to VDD through the pull-up resistor, activating micro-power shutdown. The switch and resistor ensure that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or a microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull up resistor. Table 1. LOGIC LEVEL TRUTH TABLE FOR SHUTDOWN OPERATION SHUTDOWN OPERATIONAL MODE Low Full power, stereo BTL amplifiers High Micro-power Shutdown SELECTING PROPER EXTERNAL COMPONENTS Optimizing the LM4866's performance requires properly selecting external components. Though the LM4866 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. The LM4866 is unity-gain stable, giving a designer maximum design flexibility. The gain should be set to no more than a given application requires. This allows the amplifier to achieve minimum THD+N and maximum signal-tonoise ratio. These parameters are compromised as the closed-loop gain increases. However, low gain demands input signals with greater voltage swings to achieve maximum output power. Fortunately, many signal sources such as audio CODECs have outputs of 1VRMS (2.83VP-P). Please refer to the Audio Power Amplifier Design section for more information on selecting the proper gain. Input Capacitor Value Selection Amplifying the lowest audio frequencies requires high value input coupling capacitor (Ci in Figure 32). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with this limited frequency response reap little improvement by using large input capacitor. Besides effecting system cost and size, Ci has an affect on the LM4866's click and pop performance. When the supply voltage is first applied, a transient (pop) is created as the charge on the input capacitor changes from zero to a quiescent state. The magnitude of the pop is directly proportional to the input capacitor's size. Higher value capacitors need more time to reach a quiescent DC voltage (usually VDD/2) when charged with a fixed current. The amplifier's output charges the input capacitor through the feedback resistor, Rf. Thus, pops can be minimized by selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency. A shown in Figure 32, the input resistor (RI) and the input capacitor, CI produce a -3dB high pass filter cutoff frequency that is found using Equation 7. 14 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 (7) As an example when using a speaker with a low frequency limit of 150Hz, CI, using Equation 4, is 0.063F. The 1.0F CI shown in Figure 32 allows the LM4866 to drive high efficiency, full range speaker whose response extends below 30Hz. Bypass Capacitor Value Selection Besides minimizing the input capacitor size, careful consideration should be paid to value of CB, the capacitor connected to the BYPASS pin. Since CB determines how fast the LM4866 settles to quiescent operation, its value is critical when minimizing turn-on pops. The slower the LM4866's outputs ramp to their quiescent DC voltage (nominally 1/2 VDD), the smaller the turn-on pop. Choosing CB equal to 1.0F along with a small value of Ci (in the range of 0.1F to 0.39F), produces a click-less and pop-less shutdown function. As discussed above, choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops. OPTIMIZING CLICK AND POP REDUCTION PERFORMANCE The LM4866 contains circuitry to minimize turn-on and shutdown transients or "clicks and pop". For this discussion, turn-on refers to either applying the power supply voltage or when the shutdown mode is deactivated. While the power supply is ramping to its final value, the LM4866's internal amplifiers are configured as unity gain buffers. An internal current source changes the voltage of the BYPASS pin in a controlled, linear manner. Ideally, the input and outputs track the voltage applied to the BYPASS pin. The gain of the internal amplifiers remains unity until the voltage on the bypass pin reaches 1/2 VDD. As soon as the voltage on the BYPASS pin is stable, the device becomes fully operational. Although the bypass pin current cannot be modified, changing the size of CB alters the device's turn-on time and the magnitude of "clicks and pops". Increasing the value of CB reduces the magnitude of turn-on pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time increases. There is a linear relationship between the size of CB and the turn-on time. Here are some typical turnon times for various values of CB: CB TON 0.01F 20 ms 0.1F 200 ms 0.22F 440 ms 0.47F 940 ms 1.0F 2 Sec In order eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD may not allow the capacitors to fully discharge, which may cause "clicks and pops". NO LOAD STABILITY The LM4866 may exhibit low level oscillation when the load resistance is greater than 10k. This oscillation only occurs as the output signal swings near the supply voltages. Prevent this oscillation by connecting a 5k between the output pins and ground. AUDIO POWER AMPLIFIER DESIGN Audio Amplifier Design: Driving 1W into an 8 Load The following are the desired operational parameters: Power Output: 1WRMS Load Impedance: 8 Input Level: 1VRMS Input Impedance: 20k Bandwidth: 100Hz-20 kHz 0.25 dB Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 15 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. One way to find the minimum supply voltage is to use the Output Power vs Supply Voltage curve in the Typical Performance Characteristics section. Another way, using Equation 4, is to calculate the peak output voltage necessary to achieve the desired output power for a given load impedance. To account for the amplifier's dropout voltage, two additional voltages, based on the Dropout Voltage vs Supply Voltage in the Typical Performance Characteristics curves, must be added to the result obtained by Equation 8. The result in Equation 9. (8) (9) VDD (VOUTPEAK + (VODTOP + VODBOT)) The Output Power vs Supply Voltage graph for an 8 load indicates a minimum supply voltage of 4.6V. This is easily met by the commonly used 5V supply voltage. The additional voltage creates the benefit of headroom, allowing the LM4866 to produce peak output power in excess of 1W without clipping or other audible distortion. The choice of supply voltage must also not create a situation that violates maximum power dissipation as explained above in the Power Dissipation section. After satisfying the LM4866's power dissipation requirements, the minimum differential gain is found using Equation 10. (10) Thus, a minimum gain of 2.83 allows the LM4866's to reach full output swing and maintain low noise and THD+N performance. For this example, let AVD = 3. The amplifier's overall gain is set using the input (Ri) and feedback (Rf) resistors. With the desired input impedance set at 20k, the feedback resistor is found using Equation 11. Rf/Ri = AVD/2 (11) The value of Rf is 30k. The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired 0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth limit. The gain variation for both response limits is 0.17dB, well within the 0.25dB desired limit. The results are an and an fL = 100Hz/5 = 20Hz FH = 20kHzx5 = 100kHz (12) (13) As mentioned in the External Components Description snas1371209 section, Ri and Ci create a highpass filter that sets the amplifier's lower bandpass frequency limit. Find the coupling capacitor's value using Equation 14. (14) the result is 1/(2*20k*20Hz) = 0.398F (15) Use a 0.39F capacitor, the closest standard value. The product of the desired high frequency cutoff (100kHz in this example) and the differential gain, AVD, determines the upper passband response limit. With AVD = 3 and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 300kHz. This is less than the LM4866's 3.5MHz GBWP. With this margin, the amplifier can be used in designs that require more differential gain while avoiding performance-lrestricting bandwidth limitations. 16 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT Figure 33 through Figure 38 show the recommended four-layer PC board layout that is optimized for the 24-pin NHW-packaged LM4866 and associated external components. Figure 38 through Figure 42 show the recommended four-layer PC board layout that is optimized for the 20-pin PWP-packaged LM4866 and associated components. Figure 39 through Figure 45 show the recommended two-layer PC board layout that is optimized for the 20-pin PW-packaged LM4866 and associated components. These circuits are designed for use with an external 5V supply and 3 (or greater) speakers for the NHW- and PWP-packaged LM4866 and 4 (or greater) speakers for the PW-packaged LM4866. This circuit board is easy to use. Apply 5V and ground to the board's VDD and GND pads, respectively. Connect speakers between the board's -OUTA and +OUTA and OUTB and +OUTB pads. Apply the stereo input signal to the input pins labeled "-INA" and "-INB." The stereo input signal's ground references are connected to the respective input channel's "GND" pin, adjacent to the input pins. Figure 33. Recommended NHW PC Board Layout: Component-Side Silkscreen Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 17 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Figure 34. Recommended NHW PC Board Layout: Component-Side Layout Figure 35. Recommended NHW PC Board Layout: Upper Inner-Layer Layout 18 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Figure 36. Recommended NHW PC Board Layout: Lower Inner-Layer Layout Figure 37. Recommended NHW PC Board Layout: Bottom-Side Layout Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 19 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Figure 38. Recommended PWP Board Layout: Component-Side Silkscreen Figure 39. Recommended PWP PC Board Layout: Component-Side Layout 20 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Figure 40. Recommended PWP Board Layout: Upper Inner-Layer Layout Figure 41. Recommended PWP PC Board Layout: Lower Inner-Layer Layout Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 21 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com Figure 42. Recommended PWP Board Layout: Bottom-Side Layout Figure 43. Recommended PW PC Board Layout: Component-Side Silkscreen 22 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 LM4866 www.ti.com SNAS137E - JULY 2001 - REVISED MARCH 2013 Figure 44. Recommended PW Board Layout: Component-Side Layout Figure 45. Recommended PW PC Board Layout: Bottom-Side Layout Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 23 LM4866 SNAS137E - JULY 2001 - REVISED MARCH 2013 www.ti.com REVISION HISTORY 24 Rev Date Description 1.1 04/28/05 Changed (min) to (max) for ISD units E 03/21/2013 Changed layout of National Data Sheet to TI format Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4866 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) LM4866MTE/NOPB ACTIVE HTSSOP PWP 20 73 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM4866MTEX/NOPB ACTIVE HTSSOP PWP 20 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM (4) LM4866 MTE -40 to 85 LM4866 MTE (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4866MTEX/NOPB Package Package Pins Type Drawing SPQ HTSSOP 2500 PWP 20 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 16.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 7.1 1.6 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4866MTEX/NOPB HTSSOP PWP 20 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA PWP0020A MXA20A (Rev C) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4866MTEX LM4866MTEX/NOPB LM4866MTE/NOPB