12-22SDRUGC/S530-A2/TR8 - Everlight Electronic Co., Ltd.

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 1 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Technical Data Sheet

Right Angle Lens Chip LEDs with Bi-Color(Multi-Color)

12-22SDRUGC/S530-A2/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Multi-color type.

․Pb-free.

Descriptions

․The 12-22 SMD Taping is much smaller

than lead frame type components, thus

enable smaller board size, higher packing

density, reduced storage space and finally

smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Automotive: backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Type Material Emitted Color Lens Color

SDR AlGaInP Super Deep-Red

UG GaP Green Water Clear

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 2 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Package Outline Dimensions

C1

(-)

For reflow soldering (propose)

Cathode mark

R0.44

A

1.5

1.0

1.5

G

R

A

2.0

3.0

1.0

A

C2

0.9

A

0.9 0.65

3.5

(-) (+)

Polarity

Notes: Tolerances Unless Dimension ±0.1mm ,Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 3 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit

Reverse Voltage VR 5 V

Forward Current IF SDR:25

UG:30 mA

Operating Temperature Topr -40 ~ +85 ℃

Storage Temperature Tstg -40 ~ +90 ℃

Soldering Temperature Tsol 260 (for 5 second) ℃

Electrostatic Discharge ESD 2000 V

Power Dissipation Pd SDR:60

UG:100 mW

Peak Forward Current

(Duty 1/10 @1KHz) IFP SDR:60

UG:60 mA

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Min. Typ. Max. Unit Condition

Luminous Intensity Iv SDR:

UG:

17

9.0

30

16 ------ mcd

Viewing Angle 2θ1/2 ----- 120 ----- deg

Peak Wavelength λp SDR

UG

----- 650

570 ----- nm

Dominant Wavelength λd SDR

UG

-----

639

571 -----

-----

nm

Spectrum Radiation

Bandwidth

△λ SDR

UG ----- 20

30 ----- nm

Forward Voltage VF SDR

UG ----- 2.0

2.1 2.4

2.4 V

IF=20mA

Reverse Current IR ----- ----- 10 μA VR=5V

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 4 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Typical Electro-Optical Characteristics Curves

SDR

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 5 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Typical Electro-Optical Characteristics Curves

UG

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 6 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Label explanation

CAT: Luminous Intensity Rank

HUE: Dom. Wavelength Rank

REF: Forward Voltage Rank

Reel Dimensions

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 7 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Moisture Resistant Packaging

Aluminum moistue-proof bag LabelDesiccant

Label

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 8 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

No. Items Test Condition

Test

Hours/Cycles Sample

Size Ac/Re

1 Reflow Soldering

Temp. : 260℃±5℃

Min. 5sec. 6 Min. 22 PCS. 0/1

2 Temperature Cycle

H : +100℃ 15min

∫ 5 min

L : -40℃ 15min

300 Cycles 22 PCS. 0/1

3 Thermal Shock

H : +100℃ 5min

∫ 10 sec

L : -10℃ 5min

300 Cycles 22 PCS. 0/1

4 High Temperature

Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1

5 Low Temperature

Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1

6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1

7 High Temperature /

High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 9 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

EVERLIGHT ELECTRONICS CO.,LTD.

12-22SDRUGC/S530-A2/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 10 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do

soldering of each terminal. Be careful because the damage of the product is often started at the time of

the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a

double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether

the characteristics of the LEDs will or will not be damaged by repairing.

E

VERLIGHT ELECTRO

N

ICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306

Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com