Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
NPCAPTM-PMASeries
・The new construction provides a low profile and high CV.
・Super low ESR, impedance, and high heat resistance characteristics have been secured
by using highly conductive polymer electrolytic materials.
・Compatible with digitalization and high frequencies of electrical equipment with superior
noise absorption.
・Excellent ESR characteristics, high ripple current, 5,000 hours at 105°C.
・Low-profile product lineup
・Outer coating: Flame-retardant epoxy resin UL94 V-0 or equivalent
・Non-solvent resistant type
・RoHS2 Compliant
・Halogen free products
・This product can’t be used for applications related to human life (such as in-vehicle equipment).
◆SPECIFICATIONS
Items Characteristics
Category
Temperature Range -55 to +105℃
Rated Voltage Range
16 to 25Vdc
Capacitance Tolerance
±20% (M) (at 20℃, 120Hz)
Surge Voltage Rated voltage×1.15 (at 105℃)
Leakage Current
*Note
Shall not exceed values shown in STANDARD RATINGS. (at 20℃ after 2 minutes)
Dissipation Factor (tanδ)
0.12 max. (at 20℃, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours
at 105℃.
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦200% of the initial specified value
ESR ≦200% of the initial specified value
Leakage current ≦The initial specified value
Damp Heat
(Steady State)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 60℃,
90 to 95% RH without voltage applied.
Appearance No significant damage
Capacitance change ≦-20 to +40% of the initial value
D.F. (tanδ)≦200% of the initial specified value
ESR ≦200% of the initial specified value
Leakage current ≦The initial specified value
Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦200% of the initial specified value
ESR ≦200% of the initial specified value
Leakage current ≦The initial specified value
Soldering Heat The following specifications shall be satisfied when the solder temperature is reduced back to 20°
C to measure dip resistance after
soldering has been performed under the recommended soldering conditions.
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦150% of the initial specified value
ESR ≦150% of the initial specified value
Leakage current
≦The initial specified value
(Voltage treatment)
Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
L
A
W
B
P
*
2
*2 : The dimension P (the distance between terminals) shall
be the shortest distance between the land and grounding surface.
Size code A B C L W P
F30 7.0±0.1 7.0±0.1 7.2±0.2 3.0 max. 1.2±0.2 3.50±0.2
Surface Mount
◆MARKING
A358
E220
・Rated voltage symbol
Rated voltage
(Vdc)16 20 25
Symbol C D E
・Capacitance symbol
Capacitance code
(ex. 22μF:220)
CAT. No. E1001T
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
アルミ_英_02.indd 30 2019/04/02 14:38:37