* es D ag ZE k I c Pa GN 9 d O te 63 c le EC E71 e S .R e# .L Fil U TO - 92 THERMOTAB TO-220AB A TO-202AB K G Sensitive SCRs (0.8 - 10 Amps) 5 General Description Tape-and-reel packaging is available for the TO-92 package. Please consult factory for more information. The Teccor Electronics, Inc. line of sensitive SCR semiconductors are half-wave unidirectional gate-controlled rectifiers (SCRthyristor) which complement Teccor's line of power SCRs. This group of packages offers ratings of 0.8-10 amps, and 50-600 volts with gate sensitivities of 12-500 microamps. If gate currents in the 10-50 milliamp ranges are required, please consult Teccor's non-sensitive SCR technical data sheets. Variations of devices covered in this data sheet are available for custom design applications. Please consult the factory for more information. Electrically Isolated Packages This group of Teccor sensitive SCRs is available in a choice of three different product packages. The TO-220AB and TO-92 are electrically isolated where the case or tab is internally isolated to allow the use of low cost assembly and convenient packaging techniques. Features * * * * Glass Passivation Teccor's line of SCRs features glass-passivated junctions to ensure long term device reliability and parameter stability. Teccor's glass offers a rugged, reliable barrier against junction contamination. Teccor Electronics, Inc. (972) 580-7777 5-1 Electrically-isolated To-220AB package High Voltage Capability up to 600 Volts High Surge Capability -- up to 100 Amps Glass Chip Passivation Sensitive SCRs Electrical Specifications VDRM & VRRM IT Part Number Maximum On-state Current (1) TYPE Repetitive Peak Off-state Forward & Reverse Voltage IGT IDRM & IRRM DC Gate Trigger Current (2) (11) (17) Peak Off-state Current at VDRM & VRRM (19) VTM VGT IH Peak On-state Voltage TC = 25C (3) (10) DC Gate Trigger Voltage DC Holding Current Initial On-state Current =20mAmps (5) (14) (18) (4) (11) A K G 0.8 Amp 1.5 AMPS TO-92 See "Package Dimensions" section for variations. EC103A EC103B EC103C EC103D EC103E EC103M EC103A1 EC103B1 EC103C1 EC103D1 EC103E1 EC103M1 EC103A2 EC103B2 EC103C2 EC103D2 EC103E2 EC103M2 EC103A3 EC103B3 EC103C3 EC103D3 EC103E3 EC103M3 EC113A EC113B EC113C EC113D EC113E EC113M EC113A3 EC113B3 EC113C3 EC113D3 EC113E3 EC113M3 2N5060 2N5061 2N5062 2N5063 2N5064 2N6564 2N6565 TCR22-2 TCR22-3 TCR22-4 TCR22-6 TCR22-8 Amps TC = RMS AV Volts Amps 25C 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 .95 .95 .95 .95 .95 MIN 100 200 300 400 500 600 100 200 300 400 500 600 100 200 300 400 500 600 100 200 300 400 500 600 100 200 300 400 500 600 100 200 300 400 500 600 30 60 100 150 200 300 400 50 100 200 400 600 MAX 200 200 200 200 200 200 12 12 12 12 12 12 50 50 50 50 50 50 500 500 500 500 500 500 200 200 200 200 200 200 500 500 500 500 500 500 200 200 200 200 200 200 200 200 200 200 200 200 1.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 2.0 MAX 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 1.5 1.5 1.5 1.5 1.5 Amps TC = 100C TC = Volts TC = TC = 25C 100C mAmps MIN .25 .25 .25 .25 .25 .25 0.2 0.2 0.2 0.2 0.2 0.2 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 .25 MAX 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 8.0 8.0 8.0 8.0 8.0 8.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 125C Volts - 65C 50 50 50 50 50 100 100 100 100 100 100 200 MAX 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.5 1.5 1.5 1.5 1.5 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.0 1.0 1.0 1.0 1.0 MAX 50 50 50 50 50 100 50 50 50 50 50 100 50 50 50 50 50 100 50 50 50 50 50 100 100 100 100 100 100 100 100 100 100 100 100 100 50 50 50 50 100 TC = MAX 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 See General Notes and Electrical Specifications Notes on page 5-4. Sensitive SCRs 5-2 Teccor Electronics, Inc. (972) 580-7777 Sensitive SCRs IGM VGRM PGM PG(AV) ITSM dv/dt Peak Gate Current (16) Peak Reverse Gate Voltage Peak Gate Power Dissipation (16) Average Gate Power Dissipation Peak One Cycle Surge Forward Current (6) (7) (12) Critical RateOf-Rise Of Forward Off-State Voltage di/dt tgt Gate Controlled Maximum Turn-On Time Rate-OfGate Pulse Change Of = 10mA On-State Current Min. Width IGT = 50mA With 0.1s = 15s Rise Time With Rise Time 0.1 s (8) tq l2t Circuit Commutated Turn-Off Time (9) RMS Surge (Non-Repetitive) On-State Current For A Period Of 8.3ms For Fusing Amps Amps Volts Watts Watts 60Hz 50Hz Volts/Sec Amps/Sec Sec Sec Amps2/Sec 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MIN 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 MIN 30 30 30 30 20 15 20 20 20 20 15 10 25 25 25 25 20 10 40 40 40 40 30 20 30 30 30 30 20 15 40 40 40 40 30 20 25 25 25 25 25 25 25 75 75 60 40 30 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 TYP 3.5 3.5 3.5 3.5 3.5 3.5 2.0 2.0 2.0 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 3.0 5.0 5.0 5.0 5.0 5.0 5.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 2.2 2.2 2.2 2.2 2.2 2.2 2.2 3.5 3.5 3.5 3.5 3.5 MAX 50 50 50 50 50 50 60 60 60 60 60 60 60 60 60 60 60 60 45 45 45 45 45 45 30 30 30 30 30 30 18 18 18 18 18 18 60 60 60 60 60 60 60 50 50 50 50 50 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 See General Notes and Electrical Specifications Notes on page 5-4. Teccor Electronics, Inc. (972) 580-7777 5-3 Sensitive SCRs Electrical Specifications Part Number Non-Isolated A TYPE K VDRM & VRRM IT Maximum On-State Current (1) Repetitive Peak Off-State Forward & Reverse Voltage IDRM & IRRM IGT DC Gate Trigger Current (2) (11) (13) VTM VGT Peak On-State Voltage TC = 25C (3) (10) Peak Off-State Current at VDRM & VRRM (19) IH IGM DC Gate Trigger Voltage (4) (11) DC Holding Current Initial On-State Current = 20mA (5) (15) (18) Peak Gate Current (16) Volts mAmps G A TO-202AB 4.0 Amps Amps Amps See "Package Dimensions" section for variations. IT(RMS) IT(AV) Volts MAX MAX T106F1 4.0 2.5 T106A1 4.0 T106B1 TC = TC = TC = TC = TC = Amps 25C 110C Volts - 40C 25C 110C TC = 25C MIN MAX MAX 50 200 2.0 MAX MAX MAX MAX MIN MAX 100 2.2 1.0 0.8 0.2 2.5 100 200 5.0 1.0 2.0 100 2.2 1.0 0.8 0.2 5.0 4.0 2.5 200 1.0 200 2.0 100 2.2 1.0 0.8 0.2 5.0 T106C1 T106D1 4.0 4.0 2.5 2.5 1.0 300 400 200 200 2.0 2.0 100 100 2.2 2.2 1.0 1.0 0.8 0.8 0.2 0.2 5.0 5.0 1.0 1.0 T106E1 4.0 2.5 500 200 2.0 100 2.2 1.0 0.8 0.2 5.0 1.0 T106M1 4.0 2.5 600 200 2.0 100 2.2 1.0 0.8 0.2 5.0 1.0 T107F1 T107A1 4.0 4.0 2.5 2.5 50 100 500 500 2.0 2.0 100 100 2.5 2.5 1.0 1.0 0.8 0.8 0.2 0.2 6.0 6.0 1.0 1.0 T107B1 4.0 2.5 200 500 2.0 100 2.5 1.0 0.8 0.2 6.0 1.0 T107C1 4.0 2.5 300 500 2.0 100 2.5 1.0 0.8 0.2 6.0 1.0 T107D1 T107E1 4.0 4.0 2.5 2.5 400 500 500 500 2.0 2.0 100 100 2.5 2.5 1.0 1.0 0.8 0.8 0.2 0.2 6.0 6.0 1.0 1.0 T107M1 4.0 2.5 600 500 2.0 100 2.5 1.0 0.8 0.2 6.0 1.0 (7) General Notes * Teccor 2N5060 and 2N6564 Series devices conform to all JEDEC registered data. See specifications table on page 5-2. * The case temperature (TC) is measured as shown on dimensional outline drawings. See "Package Dimensions" section of this catalog. * All measurements (except IGT) are made with an external resistor RGK = 1k unless otherwise noted. * All measurements are made at 60Hz with a resistive load at an ambient temperature of +25oC unless otherwise specified. * Operating temperature (TJ) is -65oC to + 110oC for "EC" Series devices; -65oC to +125oC for "2N" Series devices; -40oC to +125oC for "TCR" Series; and -40oC to +110oC for all others. * * (8) (9) (10) (11) Storage temperature range (TS) is -65oC to + 150oC for TO-92 devices; -40oC to +150oC for TO-202 devices; and -40oC to +125oC for all others. (12) (13) (14) o Lead solder temperature is a maximum of +230 C for 10 seconds maximum 1/16" (1.59mm) from case. (15) (16) (17) Electrical Specification Notes (1) (2) (3) (4) (5) (6) Amps See Figures 5.1 through 5.9 for current ratings at specified operating case temperatures. See Figure 5.10 for IGT vs TC. See Figure 5.11 for instantaneous on-state current (iT) vs on-state voltage (vT ) - (typical). See Figure 5.12 for VGT vs TC. See Figure 5.13 for IH vs TC. For more than one full cycle, see Figure 5.14. Sensitive SCRs (18) (19) 5-4 0.8 - 4.0A devices also have a pulse peak forward current on-state rating (repetitive) of 75A. This rating applies for operation at 60Hz, 75C maximum tab (or anode) lead temperature, switching from 80V peak, sinusoidal current pulse width of 10s minimum, 15s maximum. See Figures 5.20 and 5.21. See Figure 5.15 for tgt vs IGT. Test conditions as follows: TC 80C, rectangular current waveform; rate-of-rise of current 10A/s. Rate-of-reversal of current 5A/s. ITM = 1A (50s pulse) Repetition Rate = 60pps. VRRM = Rated. VR = 15V minimum, VDRM = Rated. Rate-of-rise reapplied forward blocking voltage = 5V/s. Gate Bias = 0V, 100 (during turn-off time interval). Test condition is maximum rated RMS current except TO-92 devices are 1.2APK; T106/T107 devices are 4APK. VD = 6VDC, RL = 100. See Figure 5.19 for simple test circuit for measuring gate trigger voltage and gate trigger current. See Figures 5.1 through 5.9 for maximum allowable case temperature at maximum rated current. IGT = 500A maximum for TC = -40C for T106 devices. IH = 10mA maximum for TC = -65C for 2N5060 Series and 2N6564 Series devices. IH = 6mA maximum for TC = -40C for T106 devices. Pulse Width 10s. IGT = 350A maximum at TC = -65C for 2N5060 Series and 2N6564 Series devices. Latching current can be higher than 20mA for higher IGT types. Also latching current can be much higher at -40C. See Figure 5.18. TC = TJ for test conditions in off-state. Teccor Electronics, Inc. (972) 580-7777 Sensitive SCRs VGRM PGM PG(AV) ITSM dv/dt di/dt tgt tq l2t Peak Reverse Gate Voltage Peak Gate Power Dissipation (16) Average Gate Power Dissipation Peak One Cycle Surge Forward Current (6) (7) (12) Critical RateOf-Rise Of Forward Off-State Voltage RMS Surge (Non-Repetitive) On-State Current For A Period Of 8.3 msec for Fusing Volts/Sec Gate Controlled Turn-On Time Gate Pulse = 10mA Min. Width = 15s with Rise Time 0.1 s (8) Circuit Commutated Turn-Off Time (9) Amps Maximum Rate-OfChange Of On-State Current IGT = 50mA with 0.1s Rise Time Amps/Sec Sec Sec Amps2Sec TC = 110C Volts Watts Watts 60Hz 50Hz TYP MAX 6.0 6.0 1.0 1.0 0.1 0.1 20 20 16 16 8 8 50 50 4.0 4.0 50 50 1.6 1.6 6.0 1.0 0.1 20 16 8 50 4.0 50 1.6 6.0 1.0 0.1 20 16 8 50 4.0 50 1.6 6.0 6.0 1.0 1.0 0.1 0.1 20 20 16 16 8 8 50 50 4.0 4.0 50 50 1.6 1.6 6.0 1.0 0.1 20 16 8 50 4.0 50 1.6 6.0 1.0 0.1 20 16 8 50 5.0 45 1.6 6.0 6.0 1.0 1.0 0.1 0.1 20 20 16 16 8 8 50 50 5.0 5.0 45 45 1.6 1.6 6.0 1.0 0.1 20 16 8 50 5.0 45 1.6 6.0 1.0 0.1 20 16 8 50 5.0 45 1.6 6.0 6.0 1.0 1.0 0.1 0.1 20 20 16 16 8 8 50 50 5.0 5.0 45 45 1.6 1.6 MIN TYP Teccor Electronics, Inc. (972) 580-7777 5-5 Sensitive SCRs Electrical Specifications Part Number Isolated A TYPE G K A TO-220AB 6.0 Amps 8.0 Amps 10.0 Amps K VDRM & VRRM IT Non-Isolated Maximum On-State Current (1) Repetitive Peak Off-State Forward & Reverse Voltage DC Gate Trigger Current (2) (11) IDRM & IRRM VTM VGT IH Peak Off-State Current at VDRM & VRRM (19) Peak On-State Voltage TC = 25C (3) (10) DC Gate Trigger Voltage (4) (11) DC Holding Current Initial On-State Current = 20mA (5) (18) G A TO-202AB See "Package Dimensions" section for variations. S0506LS2 S0506FS21 S0506LS3 S0506FS31 S1006LS2 S1006FS21 S1006LS3 S1006FS31 S2006LS2 S2006FS21 S2006LS3 S2006FS31 S4006LS2 S4006FS21 S4006LS3 S4006FS31 S6006LS2 S6006FS21 S6006LS3 S6006FS31 S0508LS2 S0508FS21 S0508LS3 S0508FS31 S1008LS2 S1008FS21 S1008LS3 S1008FS31 S2008LS2 S2008FS21 S2008LS3 S2008FS31 S4008LS2 S4008FS21 S4008LS3 S4008FS31 S6008LS2 S6008FS21 S6008LS3 S6008FS31 S0510LS2 S0510FS21 S0510LS3 S0510FS31 S1010LS2 S1010FS21 S1010LS3 S1010FS31 S2010LS2 S2010FS21 S2010LS3 S2010FS31 S4010LS2 S4010FS21 S4010LS3 S4010FS31 S6010LS2 S6010FS21 S6010LS3 S6010FS31 Amps IT(RMS) MAX 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 IT(AV) MAX 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 Amps MAX 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 200 500 Volts MIN 50 50 100 100 200 200 400 400 600 600 50 50 100 100 200 200 400 400 600 600 50 50 100 100 200 200 400 400 600 600 General Notes * Teccor 2N5060 and 2N6564 Series devices conform to all JEDEC registered data. See specifications table on page 5-2. * The case temperature (TC) is measured as shown on dimensional outline drawings. See "Package Dimensions" section of this catalog. * All measurements (except IGT) are made with an external resistor RGK = 1k unless otherwise noted. * All measurements are made at 60Hz with a resistive load at an ambient temperature of +25oC unless otherwise specified. * Operating temperature (TJ) is -65oC to + 110oC for "EC" Series devices; -65oC to +125oC for "2N" Series devices; -40oC to +125oC for "TCR" Series; and -40oC to +110oC for all others. Sensitive SCRs IGT 5-6 mAmps TC = TC = 25C 110C MAX MAX .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 .005 0.25 Volts MAX 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Volts TC = TC = TC = - 40C 25C 110C MAX MAX MIN 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .25 1.0 0.8 .26 1.0 0.8 .25 1.0 0.8 .25 mAmps MAX 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 6.0 8.0 * Storage temperature range (TS) is -65oC to + 150oC for TO-92 devices; -40oC to +150oC for TO-202 devices; and -40oC to +125oC for all others. * Lead solder temperature is a maximum of +230oC for 10 seconds maximum 1/16" (1.59mm) from case. Teccor Electronics, Inc. (972) 580-7777 Sensitive SCRs IGM Peak Gate Current (16) VGRM PGM PG(AV) ITSM dv/dt Peak Reverse Gate Voltage Peak Gate Power Dissipation (16) Average Gate Power Dissipation Peak One Cycle Surge Forward Current (6) (12) Critical RateOf-Rise Of Forward Off-State Voltage di/dt tgt tq Gate Controlled Circuit Maximum Turn-On Time Commutated Rate-Of-Change Turn-Off Of On-State Current Gate Pulse = 10mA Min. Width = 15s Time IGT = 50mA With 0.1 s With Rise Time (9) Rise Time 0.1 s (8) l2t RMS Surge (Non-Repetitive) On-State Current For A Period Of 8.3 mSec For Fusing Volts/Sec Amps 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Volts MIN 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 Watts Watts 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 Amps 60 Hz 50 Hz 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 100 83 TC = 110C TYP 20 20 10 10 10 10 5 5 5 5 20 20 10 10 10 10 5 5 5 5 20 20 10 10 10 10 5 5 5 5 Electrical Specification Notes (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) See Figures 5.1 through 5.9 for current ratings at specified operating case temperatures. See Figure 5.10 for IGT vs TC. See Figure 5.11 for instantaneous on-state current (iT) vs on-state voltage (vT ) - (typical). See Figure 5.12 for VGT vs TC. See Figure 5.13 for IH vs TC. For more than one full cycle, see Figure 5.14. 0.8 - 4.0A devices also have a pulse peak forward current on-state rating (repetitive) of 75A. This rating applies for operation at 60Hz, 75C maximum tab (or anode) lead temperature, switching from 80V peak, sinusoidal current pulse width of 10s minimum, 15s maximum. See Figures 5.20 and 5.21. See Figure 5.15 for tgt vs IGT. Test conditions as follows: TC 80C, rectangular current waveform; rate-of-rise of current 10A/s. Rate-of-reversal of current 5A/s. ITM = 1A (50s pulse) Repetition Rate = 60pps. VRRM = Rated. VR = 15V minimum, VDRM = Rated. Rate-of-rise reapplied forward Teccor Electronics, Inc. (972) 580-7777 (11) (12) (13) (14) (15) (16) (17) (18) (19) 5-7 Amps/ Sec 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Sec TYP 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 4.0 5.0 Sec MAX 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 50 45 Amps2Sec 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 blocking voltage= 5V/s. Gate Bias = 0V, 100 (during turn-off time interval). Test condition is maximum rated RMS current except TO-92 devices are 1.2APK; T106/T107 devices are 4APK. VD = 6VDC, RL = 100. See Figure 5.19 for simple test circuit for measuring gate trigger voltage and gate trigger current. See Figures 5.1 through 5.9 for maximum allowable case temperature at maximum rated current. IGT = 500A maximum for TC = -40C for T106 devices. IH = 10mA maximum for TC = -65C for 2N5060 Series and 2N6564 Series devices. IH = 6mA maximum for TC = -40C for T106 devices. Pulse Width 10s. IGT = 350A maximum at TC = -65C for 2N5060 Series and 2N6564 Series devices. Latching current can be higher than 20mA for higher IGT types. Also latching current can be much higher at -40C. See Figure 5.18. TC = TJ for test conditions in off-state. Sensitive SCRs Electrical Specifications E TO-92 L THERMOTAB TO-220AB 0.8 Amp 1.5 Amps 4.0 Amps 6.0 Amps 8.0 Amps 10.0 Amps F2 TYPE 2 TO202AB Maximum Allowable Case Temperature (TC) - C THERMAL RESISTANCE (STEADY STATE) RJC [R JA] C/W (TYPICAL) F TYPE 1 & 3 TO-202AB 75 [160] 50 [160] 130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 CASE TEMPERATURE: Measured as Shown on Dimensional Drawing 120 110 100 JEDEC "2N" SERIES 90 80 "EC" SERIES 70 60 50 10 [100] 6.2 [80] 4.0 [65] 4.3 3.4 3.9 3.0 3.4 0 0.8 0.5 1.0 1.5 2.0 RMS On-State Current [IT(RMS)] - Amps Figure 5.1 Maximum Allowable Case Temperature vs RMS On-State Current (JEDEC "2N" Series and "EC" Series) Electrical Isolation Teccor's isolated sensitive SCRs will withstand a minimum high potential test of 2500 VAC RMS from leads to mounting tab over the device's operating temperature range. See table below for other standard and optional isolation ratings. ELECTRICAL ISOLATION FROM LEADS TO MOUNTING TAB 110 100 T1 06 90 80 &T 107 TY PE 2 70 T10 6& T10 7 TY PE 1& 3 &4 ES VIC DE VAC(RMS) CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 CASE TEMPERATURE: Measured as Shown on Dimensional Drawing 120 1.5 Maximum Allowable Case Temperature (TC) - C 130 60 50 40 0 .5 1.0 2.0 2.6 2.5 3.0 3.5 4.0 RMS On-State Current [IT(RMS)] - Amps THERMOTAB** TO-220AB 2500 4000 1.5 Standard Figure 5.2 Maximum Allowable Case Temperature vs RMS On-State Current (T106 and T107) Optional* 130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 CASE TEMPERATURE: Measured as Shown on Dimensional Drawing 120 110 EC JD 100 N" "2 "E SE ES RI RI C" 90 SE Maximum Allowable Case Temperature (TC) - C *For 4000V Isolation use "V" Suffix in part number **UL Recognized File #E71639 ES 80 70 60 50 0.51 0 0.2 0.4 0.6 0.8 1.0 1.2 Average On-State Current [IT(AV)] - Amps Figure 5.3 Sensitive SCRs 5-8 Maximum Allowable Case Temperature vs Average OnState Current (JEDEC "2N" Series and "EC" Series) Teccor Electronics, Inc. (972) 580-7777 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 CASE TEMPERATURE: Measured as Shown on Dimensional Drawing 120 110 100 1 & 3 3.0 E 2.5 P TY 2.54 2.0 4 1.9 1.5 02 1.65 1.0 40 2& 0.5 -2 0.95 0 TO S 40 60 E YP ICE 50 80 7 EV 60 100 2T 20 O- 70 120 7T 10 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 0 T1 6/ 90 T10 6& T10 &T 7T 10 YPE 7T 1& YP 3 E2 &4 140 0 T1 T1 06 D 1.5 Maximum Allowable Case Temperature (TC) - C 130 /T 06 T1 Maximum Allowable Ambient Temperature (TA) - C Sensitive SCRs 20 0 Average On-State Current [IT(AV)] - Amps 0.2 0.4 0.6 0.8 1.0 1.2 1.4 Average On-State Current [IT(AV)]- Amps Maximum Allowable Case Temperature vs Average OnState Current (T106 and T107) Figure 5.7 Maximum Allowable Ambient Temperature vs Average OnState Current 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 120 1.5 AM P 100 DE VI CE S & JE 80 DE C RI 60 "2 N" SE 1.5 AMP & JEDEC "2N" SERIES IT(AV) ES SE RI ES IT (R IT ( RM MS S) ) 40 & EC SERIES IT(AV) 100 90 80 70 60 50 20 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 0.9 2 6 8 10 Maximum Allowable Case Temperature vs RMS On-State Current 110 120 100 80 T1 06 T1 /T 06 /T 10 7 7 TO -2 TO 02 -2 02 PE TY PE 40 TY 2 & 1 & 3 4 100 90 80 70 60 10 AMP DEVICES 10 60 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 CASE TEMPERATURE: Measured as Shown on Dimensional Drawings 8 AMP DEVICES Maximum Allowable Case Temperature (TC) - C CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 6 AMP DEVICES Maximum Allowable Ambient Temperature (TA) - C Figure 5.8 Maximum Allowable Ambient Temperature vs On-State Current (1.5 Amp, JEDEC "2N" Series and "EC" Series) 140 50 20 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Maximum Allowable Ambient Temperature vs RMS OnState Current (T106 and T107) Teccor Electronics, Inc. (972) 580-7777 1 2 3 4 5 6 7 Average On-State Current [IT(AV)] - Amps RMS On-State Current [IT(RMS)] - Amps Figure 5.6 4 RMS On-State Current [IT(RMS)] - Amps On-State Current - Amps Figure 5.5 10 AMP DEVICES EC CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 TEMPERATURE: Measured as Shown on Dimensional Drawings 110 8 AMP DEVICES Maximum Allowable Case Temperature (TC) - C 140 6 AMP DEVICES Maximum Allowable Ambient Temperature (TA) - C Figure 5.4 Figure 5.9 5-9 Maximum Allowable Case Temperature vs Average OnState Current Sensitive SCRs Electrical Specifications 9.0 2.0 See General Notes for specific operating temperature range 6.0 5.0 4.0 VGT VGT (TC = 25C) 3.0 See General Notes for specific device operating temperature range. 1.5 Ratio of IGT IGT (TC = 25C) 7.0 Ratio of 8.0 .5 2.0 1.0 1.0 0 0 -65 -40 -15 +25 +65 -65 +110 +125 -40 -15 Figure 5.10 Normalized DC Gate-Trigger Current vs Case Temperature +110 +125 4.0 See General Notes for specific operating temperature range. 28 IH IH(TC = 25C) TC = 25C 24 6-10 AMP DEVICES 20 16 12 Ratio of Instantaneous On-State Current (iT) - Amps +65 Figure 5.12 Normalized DC Gate-Trigger Voltage vs Case Temperature 32 0.8-1.5 AMP TO-92 AND T106/T107 DEVICES 8 3.0 2.0 1.0 4 0 0 0 .6 .8 1.0 1.2 1.4 -65 1.6 -40 -15 +25 +65 +110 +125 Case Temperature (TC) - C Instantaneous On-State Voltage (vT) - Volts Figure 5.11 +25 Case Temperature (TC) - C Case Temperature (TC) - C Instantaneous On-State Current vs On-State Voltage (Typical) Figure 5.13 Normalized DC Holding Current vs Case Temperature Peak Surge (Non-Repetitive) On-State Current (ITSM) - Amps 200 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT: [IT(RMS)]: Max Rated Value at Specified Case Temperature 10 AMP DEVICES 100 80 8 AMP DEVICES 60 50 40 6 AMP DEVICES 30 20 T106 10 & T1 07 8 6 5 4 NOTES 1) GATE CONTROL MAY BE LOST DURING AND IMMEDIATELY FOLLOWING SURGE CURRENT INTERVAL. 2) OVERLOAD MAY NOT BE REPEATED UNTIL JUNCTION TEMPERATURE HAS RETURNED TO STEADY-STATE RATED VALUE. 3 2 1.5 A MP D EVIC ES 0.8 AMP DEVICES 1 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 200 300 400 600 1000 Surge Current Duration - full cycles Figure 5.14 Peak Surge On-State Current vs Surge Current Duration Sensitive SCRs 5-10 Teccor Electronics, Inc. (972) 580-7777 Sensitive SCRs 100 9.0 IGT = 50 A MAX 8.0 IGT = 200 A MAX TC = 25C IL IL (TC = 25C) IGT = 500 A MAX Ratio of 10 Turn-On Time (tgt) - s See General Notes for specific device operating temperature range. 7.0 IGT = 12 A MAX 6.0 5.0 4.0 3.0 2.0 1.0 0 1.0 -65 -40 -15 +25 +65 +110 +125 Case Temperature (TC) - C Figure 5.18 Normalized DC Latching Current vs Case Temperature 0.1 0.01 0.1 1 10 100 DC Gate Trigger Current (IGT) - mA Reset Normally-closed Pushbutton Figure 5.15 Typical Turn-On Time vs Gate Trigger Current Average On-State Power Dissipation [PD(AV)] - Watts 100 CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 5.0 + 6 VDC - 4.0 D.U.T. V1 T106 & T107 DEVICES 3.0 IGT 1K (1%) IN4001 IG 100 R1 VGT 2.0 1.0 Figure 5.19 Simple Test Circuit For Gate Trigger Voltage and Current Measurement 0.8 AMP TO-92 DEVICES 1.5 AMP DEVICES 0 1 2 3 4 RMS On-State Current [IT(RMS)] - Amps Note: V1 -- 0-10 volt DC meter VGT -- 0-1 volt DC meter IG -- 0-1mA DC millimeter R1 -- 1K potentiometer Figure 5.16 Power Dissipation (Typical) vs RMS On-State Current To measure gate trigger voltage and current, raise gate voltage (VGT) until meter reading V1 drops from 6 volts to 1 volt. Gate trigger voltage is the reading on VGT just prior to V1 dropping. Gate trigger current IGT can be computed from the relationship: Average On-State Power Dissipation [PD(AV)] - Watts 12 CURRENT WAVEFORM: Half Sine Wave LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 10 8 6-10 AMP TO-220 & TO-202 DEVICES 6 I 4 GT V GT= I - -----------Amps G 1000 where I G is reading (in amps) on meter just prior to V1 dropping. Note: I GT may turn out to be a negative quantity (trigger current flows out from gate lead). 2 0 0 2 4 6 8 10 RMS On-State Current [IT(RMS)] - Amps Figure 5.17 Power Dissipation (Typical) vs RMS On-State Current Teccor Electronics, Inc. (972) 580-7777 5-11 Sensitive SCRs Electrical Specifications 180 PEAK DISCHARGE CURRENT (ITM) - AMPS 160 1.0Hz 140 12H z 120 60H z 100 80 60 ITM 0.8 - 4.0A DEVICES 40 tW 20 tW = 5 TIME CONSTANTS 0 1.0 3.0 5.0 7.0 10 30 50 70 100 50 70 100 PEAK CURRENT DURATION(tW) - s Figure 5.20 Peak Repetitive Capacitor Discharge Current 180 PEAK DISCHARGE CURRENT (ITM) - AMPS 160 140 1.0 Hz 120 12 Hz 100 60 Hz 80 60 ITM 40 0.8 - 4.0A DEVICES tW 20 0 1.0 3.0 5.0 7.0 10 30 PEAK CURRENT DURATION(tW) - s Figure 5.21 Peak Repetitive Sinusoidal Curve Sensitive SCRs 5-12 Teccor Electronics, Inc. (972) 580-7777