Finisar Product Specification +3200 ps/nm (~200km) DWDM XFP Optical Transceiver FTLX4213x3xxxx PRODUCT FEATURES * Supports 10.7Gb/s to 11.35Gb/s * -500 to +3200 ps/nm Dispersion Tolerance (~200km reach without dispersion compensation) * Supports ITU C & L-Band DWDM channels * Supports 8x50GHz tuning range * Temperature-stabilized DWDM CMLTM transmitter * Temperature range: 0C to 70C * RoHS-6 Compliant (lead-free) * Power dissipation <4.0W * Adjustable receiver threshold APPLICATIONS * Amplified DWDM 10Gb/s SONET/SDH w/FEC * Amplified DWDM 10Gb/s Ethernet and 10Gb/s Fibre Channel w/FEC Finisar's FTLX4213x3xxxx Small Form Factor 10Gb/s (XFP) transceiver complies with the XFP Multi-Source Agreement (MSA) Specification1. It supports amplified DWDM 10Gb/s SONET/SDH +FEC,10 Gigabit Ethernet +FEC, and 10 Gigabit Fibre Channel +FEC applications over ~200km of fiber without dispersion compensation. The standard product supports narrow tunability on the C- and L-Band channels with 50GHz spacing. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC3, and Finisar Application Note AN-20384. PRODUCT SELECTION FTLX4213x3xxxx x: tuning range xxxx: ITU-T Channel# (see next page) (c) Finisar Corporation 16-December-2010 Rev C4 Page 1 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar C-Band, 8x50GHz XFPs (FTLX4213C3Cxxx) L-Band, 2x200GHz XFPs (FTLX4213J3Lxxx) Note* AE Please contact your Finisar representative for any requirements not supported by the above channel plan. (c) Finisar Corporation 16-December-2010 Rev C4 Page 2 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 I. Finisar Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- CML-O CML-O Name/Description Module Ground Optional -5.2 Power Supply - Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply - Not required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply - Not required Module Ground Reference Clock non-inverted input, AC coupled on the host board - Not required Reference Clock inverted input, AC coupled on the host board - Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 26 GND 1 27 GND 1 28 CML-I TD29 CML-I TD+ 30 GND 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k - 10kohms on host board to a voltage between 3.15V and 3.6V. (c) Finisar Corporation 16-December-2010 Rev C4 Page 3 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage #1 Maximum Supply Voltage #2 Storage Temperature Case Operating Temperature Receiver Damage Threshold Symbol Vcc3 Vcc5 TS TOP PRdmg (c) Finisar Corporation 16-December-2010 Min -0.5 -0.5 -40 0 +5 Rev C4 Typ Max 4.0 6.0 85 70 Unit V V C C dBm Ref. Page 4 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 III. Finisar Electrical Characteristics (TOP = 0 to 70 C, VCC5 = 4.75 to 5.25 Volts) Parameter Supply Voltage #1 Supply Voltage #2 Supply Current - Vcc5 supply Supply Current - Vcc3 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc5 Vcc3 Icc5 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 4.75 3.13 Typ Max 5.25 3.46 500 750 4.0 Unit V V mA mA W mV V V us 2 820 Vcc GND+ 0.8 10 mV ps ps V V 4 5 5 6 6 7 100 120 2.0 GND 340 Vcc - 0.5 GND 650 850 38 38 VccHOST GND+0.5 See Note 7 below Ref. 1 3 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 - 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k - 10kohm resistor to 3.15 - 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. (c) Finisar Corporation 16-December-2010 Rev C4 Page 5 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 IV. Finisar Optical Characteristics (EOL, TOP = 0 to 70C, VCC5 = 4.75 to 5.25 Volts) Transmitter Parameter Output Opt. Pwr: 9/125 SMF Optical Extinction Ratio Center Wavelength Spacing Transmitter Center Wavelength - End Of Life Sidemode Suppression ratio Tx Jitter 20kHz-80MHz Tx Jitter 4MHz - 80MHz Tx Disable Negate Time Relative Intensity Noise Receiver Maximum Input Power Optical Center Wavelength Receiver Reflectance LOS De-Assert LOS Assert LOS Hysteresis Receiver Sensitivity Data rate (Gb/s) BER 10.7 1e-4 11.1 1e-4 11.3 1e-4 OSNR Performance Data rate (Gb/s) BER Symbol POUT ER Min 0 8.2 fc X-5 SSRmin Txj1 Txj2 35 tTxE RIN PMAX C Rrx LOSD LOSA -7 1270 Typ 50 X Max +4.0 X+5 Unit dBm dB GHz GHz 0.3 0.1 dB UI UI 60 -135 seconds dB/Hz 1615 -27 -30 -37 0.5 Dispersion (ps/nm) Sensitivity back-toback at OSNR>30dB (dBm) Sensitivity at -500 to +3200ps/nm with OSNR>30dB (dB) -500 to +3200 -500 to +3200 -500 to +3200 -27 -27 -27 -25 -25 -25 Dispersion (ps/nm) Ref. 1 2 3 4,5 4,5 dBm nm dB dBm dBm dB Max OSNR, -500 ps/nm to +3200 ps/nm at Power: -8 to -19dBm (dB) 6 Threshold Adjustm. Yes Yes Yes 6,7 Threshold Adjust. 10.7 1e-4 -500 to +3200 19 Yes 11.1 1e-4 -500 to +3200 19 Yes 11.3 1e-4 -500 to +3200 19 Yes Notes: 1. Measured with unfiltered eye pattern. (without 4th order Bessel-Thompson Filter) 2. Corresponds to approximately 0.8 nm. Please contact Finisar for 50GHz support. 3. X = Specified ITU Grid frequency. Wavelength stability is achieved within xx seconds of power up. Please contact Finisar for narrow tunability support. 4. Measured with a host jitter of 50 mUI peak-to-peak. 5. GR-253-CORE Issue 4 6. Measured at 1528-1600nm with worst ER; BER<10-12; PRBS31. 7. All OSNR measurements are performed with 0.1nm resolution. (c) Finisar Corporation 16-December-2010 Rev C4 Page 6 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 V. Finisar General Specifications Parameter Bit Rate Maximum Supported Link Length Symbol BR LMAX Min 10.7 Typ Max 11.3 200 Units Gb/s km Ref. 1 Notes: 1. Distance indicates dispersion budget. Optical amplification is required to achieve maximum distance. VI. Environmental Specifications Finisar FTLX4213x3xxxx XFP transceivers have an operating temperature range from -5C to +70C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units C C Ref. Regulatory Compliance Finisar FTLX4213x3xxxx XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TUV 72101686 Electrical Safety Electrical Safety TUV EN 60825-1: 2007, EN60825-2:2004+A1 IEC 60825-1: 2007 (2nd Edition) IEC 60825-2: 2010 (3rd Edition) EN 60950:2006+A11 CLASS 3862.07 CLASS 3862.87 2283290 UL/CSA Certificate Number 9210176-77 72101686 Copies of the referenced certificates are available at Finisar Corporation upon request. (c) Finisar Corporation 16-December-2010 Rev C4 Page 7 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar VIII. Digital Diagnostics Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: * * * * * * Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage TEC Temperature It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information, including memory map definitions, please see the XFP MSA documentation1. Receiver Threshold Adjustment The FTLX4213M3xxx also provides access to receiver decision threshold adjustment via 2-wire serial interface, in order to improve receiver OSNR performance based on specific link conditions. It is implemented as follows: * * Rx Threshold of XFP transceivers will be factory-set for optimized performance in non-FEC applications. This will be the default value during both cold start (power-up) and warm start (module reset). The transceiver supports adjustment of Rx Threshold value by the host through register 76d, table 01h. This is intended to be used in FEC applications. (c) Finisar Corporation 16-December-2010 Rev C4 Page 8 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 * * Finisar Register 76d, table 01h is a volatile memory. Therefore if the transceiver is power-cycled, the register starts up with a value of 00h which corresponds to the default Rx Threshold value. The threshold adjustment input value is 2's complement 7 bit value (-128 to +127), with 0 corresponding to default Rx threshold value. Full range of adjustment provides at least a 10% change in Rx threshold from the default value. ITU channel Tuning (per SFF-8477 rev 1.3) To avoid possible conflict with legacy tuning systems designed to INF-8077i, the frequency grid tuning commands of SFF-8477 supplement rather than supplant the wavelength grid tuning commands of INF-8077i. Tuning Management Interface for ITU Frequency Grid Applications Finisar's FTLX4213M3xxxx supports Frequency tuning by channel number only. The XFP frequency tuning is indicated by the transceiver description encoded in Serial ID Byte 138 bit 3. Data Address 138 138 138 Bit 3 2 0-1 Description Tunable DWDM (selection by channel number, bytes 112-113) Tunable DWDM (selection in 50 pm steps, bytes 72-73) Reserved A desired frequency channel can be commanded by the user by writing into Bytes 112 (MSB) and 113 (LSB). Frequency channel control command: Address Bit Name 112 (MSB) & All Channel 113 (LSB) Number Set 114 (MSB) & 115 (LSB) 116 - 117 All All Description User input of channel number, which is an integer 1 to N (N=Number of Channels) Frequency Error Frequency error reported in 16 bit signed integer with LSB=0.1 GHz Reserved Reserved The channel number is derived from the following equation using parameters found in Module capabilities as listed in Byte Addresses 60-69: Channel number = 1 + (Desired Frequency - First Frequency) / Grid Spacing If "0" is used for the channel number, the XFP will go into standby mode until a valid channel number is received. (c) Finisar Corporation 16-December-2010 Rev C4 Page 9 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar Tunable Transceiver Initialization / Power Cycling: When a tunable module is plugged in for the first time it will go to a default channel, or if Tx_DIS is asserted it will go to a standby condition. When the module is power cycled it will automatically go to the last channel selected, or if Tx_DIS is asserted it will go to a standby condition. If Tx_DIS is asserted, the last channel selected will be cleared, and a valid new channel command will be required to set a channel. If the Tx is disabled and then re-enabled, the module returns to the last channel selected. IX. Mechanical Specifications Finisar's XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). XFP Transceiver (dimensions are in mm) (c) Finisar Corporation 16-December-2010 Rev C4 Page 10 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 X. Finisar PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) (c) Finisar Corporation 16-December-2010 Rev C4 Page 11 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar XFP Detail Host Board Mechanical Layout (dimensions are in mm) XFP Recommended Bezel Design (dimensions are in mm) (c) Finisar Corporation 16-December-2010 Rev C4 Page 12 FTLX4213x3xxxx 3200ps/nm DWDM XFP Product Specification - December 2010 Finisar XI. Notes & Exceptions The FTLX4213x3xxxx product family has the following exceptions to the XFP MSA; o Tx_Disable time of <100usec, o Tx_Disable negate time of <60seconds o Tx_NR is not implemented. o Reset Completion Bit is not implemented in EEPROM (Table 0: Byte 84: Bit 0) XII. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 - August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers" - Finisar Corporation, December 2003 3. Directive 2002/95/EC of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". January 27, 2003. 4. "Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers", Finisar Corporation, January 21, 2005. XIII. Revision History Revision Date A1 4/15/2008 C1 7/20/2009 C2 3/18/2010 C3 C4 XII. Description * Preliminary document created. * Updated Optical Spec for OSNR & Rx_Sensitivity * Updated Tx_Disable <100us * Updated Icc3 value * Corrected Finisar Part Numbers 8/28/2010 * Added "Notes & Exceptions" Section 12/16/2010 * Updated channel availability For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com (c) Finisar Corporation 16-December-2010 Rev C4 Page 13