SiT8102
1 to 200 MHz High Performance Oscillator
SiTime Corporation 990 Almanor Avenue Sunnyvale, CA 94085 (408) 328-4400 www.sitime.com
Rev. 1.10 Revised June 9, 2010
Features
High frequency stability
±10 PPM, ±15 PPM, ±20 PPM
±25 PPM, ±50 PPM, ±100 PPM
Extremely low RMS phase jitter (random)
0.5 ps (typical)
Wide frequency range
1 to 200 MHz
Operating voltage
1.8, 2.5, 2.8V or 3.3 V
Other voltages up to 3.63 V (contact SiTime)
Operating temperature range
Industrial, -40 to 85 °C
Extended Commercial, -20 to 70 °C
Commercial, 0 to 70 °C
Small footprint
2.5 x 2.0 x 0.75 mm
3.2 x 2.5 x 0.75 mm
5.0 x 3.2 x 0.75 mm
7.0 x 5.0 x 0.90 mm
All packages are Pb-free and ROHs compliant
High drive option: 30pF load (contact factory)
Benefits
No crystal or load capacitors required
Eliminates crystal qualification time
Ultra-reliable start up and greater immunity from interfer-
ence
Replaces expensive single-ended SAW oscillators
More cost effective than quartz oscillators, quartz crystals
and clock ICs.
Completely quartz-free
Applications
Communications and Networking Applications
Consumer Electronics Applications
Automotive Applications
Industrial Applications
Gigabit Ethernet
10 Gigabit Ethernet
Fiber Channel
Ethernet
SATA/SAS
USB 2.0
PCI-Express
MEMS
Resonator
GND
VDD OUT
ST/OE
High
Performance
Synthesizer
Block Diagram Pinout
14
32
ST/OE VDD
OUTGND
Pin Description
Pin No. Name Pin Description
1ST/OE Standby/ Output Enable
2 GND Connect to Ground
3 OUT 1 to 200 MHz Programmed Clock
output
4 VDD Connect to 1.8V / 2.5V / 2.8V / 3.3V
Pin1
Pin #1 Functionality
OE
H or Open; specified frequency output
L: output is high impedance
ST
H or Open; specified frequency output
L: output is low level (weak pull down) oscillation stops
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 2 of 8 www.sitime.com
Description
The SiT8102 is the next generation of the SiT8002 program-
mable oscillator with lower phase noise, lower jitter, and a
wider frequency range. SiTime oscillators are the smallest,
high-performance programmable oscillator available and are
suitable for use in high speed serial communications,
consumer, portable, industrial, automotive and computation.
This oscillator is packaged in standard low-cost plastic and
chip-scale IC packages.
System reliability is also increased with the SiT8102 by elimi-
nating the quartz crystal and improved immunity to the
environmental effects of vibration, shock, strain, and humidity.
To order samples, go to www.sitime.com and click on Request
Sample” link.
Absolute Maximum Ratings
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual perfor-
mance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Notes:
1. The 3.3V device can operate from 2.25V to 3.63V with higher output drive strength, however, the data sheet specifications cannot be guaranteed. Please contact
factory for this option.
2. The output driver strength can be programmed to drive up to 50pF load. Please contact factory for this option.
Absolute Maximum Table
Parameter Min. Max. Unit
Storage Temperature -65 150 °C
VDD -0.5 +3.66 V
Electrostatic Discharge 2000 V
Theta JA ( with copper plane on VDD and GND) 75 °C/W
Theta JC (with PCB traces of 0.010 inch to all pins) 24 °C/W
Soldering Temperature (follow standard Pb free soldering guidelines) 260 °C
Number of Program Writes 1 NA
Program Retention over -40 to 125 °C, Process, VDD (0 to 3.65V) 1,000+ years
Operating Conditions
Parameter Min. Typ. Max. Unit
Supply Voltages, VDD[1] 2.97 3.3 3.63 V
2.52 2.8 3.08 V
2.25 2.5 2.75 V
1.7 1.8 1.9 V
Commercial Operating Temperature 0 70 °C
Extended Commercial Operating Temperature -20 70 °C
Industrial Operating Temperature -40 85 °C
Maximum Load Capacitance[2] 15 pF
Environmental Compliance
Parameter Condition/Test Method
Mechanical Shock MIL-STD-883F, Method 2002
Mechanical Vibration MIL-STD-883F, Method 2007
Temperature Cycle JESD22, Method A104
Solderability MIL-STD-883F, Method 2003
Moisture Sensitivity Level MSL1 @ 260°C
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 3 of 8 www.sitime.com
DC Electrical Specifications
VDD = 3.3V ±10%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Output Voltage High IOH = -9 mA 90 %Vdd
Output Voltage Low IOL = 9 mA 10 %Vdd
Input Voltage High Pin 1 70 %Vdd
Input Voltage Low Pin 1 30 %Vdd
Operating Current Output frequency = 30 MHz, 15 pF load 26 mA
Output frequency = 125 MHz, 15 pF load 34 mA
Standby Current Output is weakly pulled down, ST = GND 30 50 µA
Power Up Time Time from minimum power supply voltage to the
first cycle (Guaranteed no runt pulses)
––10ms
VDD = 2.5V ±10% or VDD = 2.8V ±10%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Output Voltage High IOH = -7 mA 90 %Vdd
Output Voltage Low IOL = 7mA - 10 %Vdd
Input Voltage High Pin 1 70 %Vdd
Input Voltage Low Pin 1 30 %Vdd
Operating Current Output frequency = 30 MHz, 15 pF load 26 mA
Output frequency = 125 MHz, 15 pF load 31 mA
Standby Current Output is weakly pulled down, ST = GND 30 50 µA
Power Up Time Time from minimum power supply voltage to the
first cycle (Guaranteed no runt pulses)
––10ms
VDD = 1.8V ±5%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Output Voltage High IOH = -5 mA 90 %Vdd
Output Voltage Low IOL = 5 mA - 10 %Vdd
Input Voltage High Pin 1 70 %Vdd
Input Voltage Low Pin 1 30 %Vdd
Operating Current Output frequency = 30 MHz, 15 pF load 26 mA
Output frequency = 125 MHz, 15 pF load 31 mA
Standby Current Output is weakly pulled down, ST = GND 30 50 µA
Power Up Time Time from minimum power supply voltage to the
first cycle (Guaranteed no runt pulses)
––10ms
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 4 of 8 www.sitime.com
AC Electrical Specifications
VDD = 3.3V ±10%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Clock Output Frequency 1 200 MHz
Frequency Stability Inclusive of initial tolerance,
operating temp., rated power
supply voltage change, load
change
0 to 70°C -10 +10 PPM
-20 to 70°C
-40 to 85°C
-15 +15 PPM
-20 +20 PPM
-25 +25 PPM
-50 +50 PPM
-100 +100 PPM
Aging First year @ 25 °C 1 PPM
Clock Output Duty Cycle Output frequency= 1 to 125 MHz 45 55 %
Output frequency= 125 to 200 MHz 40 60 %
Clock Output Rise Time 15 pF Load, 20% to 80% VDD 1.0 1.5 ns
Clock Output Fall Time 15 pF Load, 80% to 20% VDD 1.0 1.5 ns
RMS Period Jitter Output frequency = 75 MHz 2.6 4 ps
Output frequency = 125 MHz 2.4 3.6 ps
RMS Phase Jitter (Random) Output frequency = 75 MHz (900 kHz to 7.5 MHz) –0.81– ps
Output frequency = 106.25 MHz (637kHz to 10 MHz) –1.64– ps
Output frequency = 125 MHz (1.875 to 20 MHz) –0.38– ps
VDD = 2.5V ±10% or VDD = 2.8V ±10%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Clock Output Frequency 1 200 MHz
Frequency Stability Inclusive of initial tolerance,
operating temp., rated power
supply voltage change, load
change
0 to 70°C -10 +10 PPM
-20 to 70°C
-40 to 85°C
-15 +15 PPM
-20 +20 PPM
-25 +25 PPM
-50 +50 PPM
-100 +100 PPM
Aging First year @ 25 °C 1 PPM
Clock Output Duty Cycle Output frequency= 1MHz to 125MHz 45 55 %
Output frequency= 125MHz to 200MHz 40 60 %
Clock Output Rise Time 15 pF Load, 20% to 80% VDD 1.0 1.5 ns
Clock Output Fall Time 15 pF Load, 80% to 20% VDD 1.0 1.5 ns
RMS Period Jitter Output frequency = 75 MHz 3 6 ps
Output frequency = 125 MHz 2.8 5 ps
RMS Phase Jitter (Random) Output frequency = 75 MHz (900 kHz to 7.5 MHz) –0.87– ps
Output frequency = 106.25 MHz (637kHz to 10 MHz) –1.7– ps
Output frequency = 125 MHz (1.875 to 20 MHz) –0.41– ps
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 5 of 8 www.sitime.com
VDD = 1.8V ±5%, -40 to 85°C
Parameter Condition Min. Typ. Max. Unit
Clock Output Frequency 1 200 MHz
Frequency Stability Inclusive of initial tolerance,
operating temp., rated power
supply voltage change, load
change
0 to 70°C -15 +15 PPM
-20 to 70°C
-40 to 85°C
-20 +20 PPM
-25 +25 PPM
-50 +50 PPM
-100 +100 PPM
Aging First year @ 25 °C 1 PPM
Clock Output Duty Cycle Output frequency= 1 MHz to 75 MHz 45 55 %
Output frequency= 75 MHz to 200 MHz 40 60 %
Clock Output Rise Time 15 pF Load, 20% to 80% VDD 1.0 1.5 ns
Clock Output Fall Time 15 pF Load, 80% to 20% VDD 1.0 1.5 ns
RMS Period Jitter Output frequency = 75 MHz 7.3 14 ps
Output frequency = 125 MHz 7.1 14 ps
RMS Phase Jitter (Random) Output frequency = 75 MHz (900 kHz to 7.5 MHz) 0.85 ps
Output frequency = 106.25 MHz (637kHz to 10 MHz) 1.72 ps
Output frequency = 125 MHz (1.875 to 20 MHz) 1.06 ps
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 6 of 8 www.sitime.com
Ordering Information
Notes:
3. Without Center Pad.
Frequency
1.00000 to 200.00000 MHz
Part Family
“SiT8102
Revision Letter
“A” is the silicon revision
Temperature Range
“I” Industrial, -40 to 85ºC Voltage Supply
“18” for 1.8V ±5%
“25” for 2.5V ±10%
“28” for 2.8V ±10%
“33” for 3.3V ±10%
Packaging
Blank for Bulk
Output Driver Strength
“–” Default
Feature Pin
“E” for Output Enable
“S” for Standby
“C” Ext. Commercial, -20 to 70ºC
“N” Commercial, 0 to 70ºC
Frequency Tolerance
“F” for ±10 PPM
“H” for ±15 PPM
“1” for ±20 PPM
“2” for ±25 PPM
“3” for ±50 PPM
“4” for ±100 PPM
Package Size
“1” 2.5 x 2.0 mm
“2” 3.2 x 2.5 mm
“3” 5.0 x 3.2 mm
“T”: Tape & Reel, 3K reel
“Y”: Tape & Reel, 1K reel
“4” 7.0 x 5.0 mm
“8” 7.0 x 5.0 mm
[3]
SiT8102AC -13-25E - 105.12345T
Frequency Stability vs. Temperature Range Options
Frequency
Stability (PPM)
Temperature
Range
Supply Voltage
1.8 V 2.5 V 3.3 V
±10
N (0 to +70°C) 33
C (-20 to +70°C) ––
I (-40 to +85°C) ––
±15
N (0 to +70°C) 333
C (-20 to +70°C) 33
I (-40 to +85°C) 33
±20
N (0 to +70°C) 333
C (-20 to +70°C) 333
I (-40 to +85°C) 333
±25
N (0 to +70°C) 333
C (-20 to +70°C) 333
I (-40 to +85°C) 333
±50
N (0 to +70°C) 333
C (-20 to +70°C) 333
I (-40 to +85°C) 333
SiT8102
1 to 200 MHz High Performance Oscillator
Rev. 1.10 Page 7 of 8 www.sitime.com
Package Information [4,5]
Dimension (mm) Land Pattern (recommended) (mm)[6]
2.5 x 2.0 x 0.75mm
2.5±0.10
2.0±0.10
1.1
1.0
0.75
0.5
0.75±0.05
YXXXX
1.9
1.1
1.0
1.5
3.2±0.15
2.5±0.15
2.1
0.9
0.7
0.9
YXXXX
0.75±0.05
2.2
1.9
1.4
1.2
5.0 x 3.2 x 0.75 mm
5.0±0.15
3.2±0.15
2.39
0.8
1.15
1.1
YXXXX
0.75±0.05
2.54
1.5
2.2
1.6
Rev. 1.10 Page 8 of 8 Revised June 9, 2010
© SiTime Corporation 2010. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a
Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii)
unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper
installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress.
Disclaimer: SiTime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and all express or implied warranties, either in fact or by
operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or
usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any sitime product and any product documentation. products sold by
sitme are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved or
at stake. all sales are made conditioned upon compliance with the critical uses policy set forth below.
CRITICAL USE EXCLUSION POLICY
BUYER AGREES NOT TO USE SITIME'S PRODUCTS FOR ANY APPLICATION OR IN ANY COMPONENTS USED IN LIFE SUPPORT DEVICES OR TO OPERATE NUCLEAR FACILITIES
OR FOR USE IN OTHER MISSION-CRITICAL APPLICATIONS OR COMPONENTS WHERE HUMAN LIFE OR PROPERTY MAY BE AT STAKE.
SiTime owns all rights, title and interest to the intellectual property related to SiTime's products, including any software, firmware, copyright, patent, or trademark. The sale of SiTime products
does not convey or imply any license under patent or other rights. SiTime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to
the sale of products or services by SiTime. Unless otherwise agreed to in writing by SiTime, any reproduction, modification, translation, compilation, or representation of this material shall be
strictly prohibited.
SiT8102
1 to 200 MHz High Performance Oscillator
Notes:
4. Y top marking denotes manufacturing origin. The value of “Y” will depend on the assembly location of the device.
5. XXXXtop marking denotes manufacturing lot number.
6. A capacitor of value 0.1μF between VDD and GND is recommended.
7. The 7050 package with part number designation "-8" has NO center pad.
Package Information (continued)[4,5]
Dimension (mm) Land Pattern (recommended) (mm)[6]
5.0 ± 0.15
1.4
1.1
5.08
7.0 ± 0.15
2.6
1.7
2.1
0.90 ± 0.10
YXXXX
No Connect[7]
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
SiTime:
SIT8102AC-33-33E-100.00000 SIT8102AC-33-33E-25.00000 SiT8102AI-13-18E-100.00000 SIT8102AC-33-25E-
50.000 SIT8102AI-13-18E-98.000Y SIT8102AI-13-18E-98.00000 SIT8102AN-23-25S-26.00000 SIT8102AC-33-33E-
10.00000 SiT8102AC-13-18E-100.00000X SiT8102AC-13-18E-106.25000X SiT8102AC-13-18E-12.00000X
SiT8102AC-13-18E-125.00000X SiT8102AC-13-18E-14.31818X SiT8102AC-13-18E-16.00000X SiT8102AC-13-18E-
2.04800X SiT8102AC-13-18E-20.00000X SiT8102AC-13-18E-24.00000X SiT8102AC-13-18E-24.57600X SiT8102AC-
13-18E-25.00000X SiT8102AC-13-18E-27.00000X SiT8102AC-13-18E-33.33300X SiT8102AC-13-18E-4.00000X
SiT8102AC-13-18E-40.00000X SiT8102AC-13-18E-48.00000X SiT8102AC-13-18E-50.00000X SiT8102AC-13-18E-
8.00000X SiT8102AC-13-18E-80.00000X SiT8102AC-13-25E-1.84320X SiT8102AC-13-25E-10.00000X SiT8102AC-
13-25E-100.00000X SiT8102AC-13-25E-106.25000X SiT8102AC-13-25E-12.00000X SiT8102AC-13-25E-125.00000X
SiT8102AC-13-25E-13.00000X SiT8102AC-13-25E-13.56000X SiT8102AC-13-25E-14.31818X SiT8102AC-13-25E-
14.74560X SiT8102AC-13-25E-16.00000X SiT8102AC-13-25E-18.43200X SiT8102AC-13-25E-2.04800X SiT8102AC-
13-25E-20.00000X SiT8102AC-13-25E-24.00000X SiT8102AC-13-25E-24.57600X SiT8102AC-13-25E-25.00000X
SiT8102AC-13-25E-27.00000X SiT8102AC-13-25E-3.68640X SiT8102AC-13-25E-30.00000X SiT8102AC-13-25E-
32.00000X SiT8102AC-13-25E-32.76800X SiT8102AC-13-25E-33.00000X SiT8102AC-13-25E-33.33300X
SiT8102AC-13-25E-4.00000X SiT8102AC-13-25E-40.00000X SiT8102AC-13-25E-48.00000X SiT8102AC-13-25E-
5.00000X SiT8102AC-13-25E-50.00000X SiT8102AC-13-25E-6.00000X SiT8102AC-13-25E-60.00000X SiT8102AC-
13-25E-64.00000X SiT8102AC-13-25E-66.00000X SiT8102AC-13-25E-66.66667X SiT8102AC-13-25E-75.00000X
SiT8102AC-13-25E-8.00000X SiT8102AC-13-25E-80.00000X SiT8102AC-13-33E-1.84320X SiT8102AC-13-33E-
10.00000X SiT8102AC-13-33E-100.00000X SiT8102AC-13-33E-106.25000X SiT8102AC-13-33E-12.00000X
SiT8102AC-13-33E-125.00000X SiT8102AC-13-33E-13.00000X SiT8102AC-13-33E-13.56000X SiT8102AC-13-33E-
14.31818X SiT8102AC-13-33E-14.74560X SiT8102AC-13-33E-16.00000X SiT8102AC-13-33E-18.43200X
SiT8102AC-13-33E-2.04800X SiT8102AC-13-33E-20.00000X SiT8102AC-13-33E-24.00000X SiT8102AC-13-33E-
24.57600X SiT8102AC-13-33E-25.00000X SiT8102AC-13-33E-27.00000X SiT8102AC-13-33E-3.68640X SiT8102AC-
13-33E-30.00000X SiT8102AC-13-33E-32.00000X SiT8102AC-13-33E-32.76800X SiT8102AC-13-33E-33.00000X
SiT8102AC-13-33E-33.33300X SiT8102AC-13-33E-4.00000X SiT8102AC-13-33E-40.00000X SiT8102AC-13-33E-
48.00000X SiT8102AC-13-33E-5.00000X SiT8102AC-13-33E-50.00000X SiT8102AC-13-33E-6.00000X SiT8102AC-
13-33E-60.00000X SiT8102AC-13-33E-64.00000X SiT8102AC-13-33E-66.00000X SiT8102AC-13-33E-66.66667X
SiT8102AC-13-33E-75.00000X SiT8102AC-13-33E-8.00000X