611 Industrial Way West, Eatontown, NJ 07724 tel: 732-460-0212 fax: 732-460-0214 sales@advanced-control.com www.advanced-control.com
Each detector model contains:
• Input Impedance Matching
• DC return
• RF bypass capacitor
• Detector diode
Applications:
• Transmitter Monitoring
• Radar Equipment
• Missile Guidance Systems
• Input to Low-Noise Amplifiers
• Broadband Or Narrowband ECM Receivers
• Power and Signal Monitors
• Doppler Radar and Beacon Receivers
• Matched units available for Multi-channel Receivers, Amplitude Comparator Systems and Discriminators
Minimum(2) Flatness Nominal (4)
Frequency Sensitivity vs Typical (2) Video Standard Optional
Range Part (1) K Frequency TSS Capacitance Case Case
(GHz) Number (mV/mW) (+/-dB) (dBm) (pF) Styles Styles
0.1 - 1 ACSP2517N 2000 0.28 -52 270 C3 C8,C15
0.1 - 2 ACSP2538N 2000 0.3 -52 270 C3 C8,C15
0.5 - 2 ACSP2501N 2000 0.3 -53 75 C3 C8,C15
1 - 4 ACSP2630N 2000 0.3 -53 39 C3 C8,C15
2 - 4 ACSP2502N 2000 0.2 -53 20 C3 C8,C15
2 - 6 ACSP2546N 2000 0.3 -53 12 C3 C8,C15
1 - 6 ACSP2656N 2000 0.5 -53 12 C3 C8,C15
4 - 8 ACSP2503N 2000 0.3 -53 12 C3 C8,C15
0.5 - 12 ACSP2658N 2000 1.3 -52 75 C3 C8,C15
1 - 12 ACSP2762N 2000 1.5 -51 20 C3 C8,C15
2 - 12 ACSP2507N 2000 1.1 -53 12 C3 C8,C15
8 - 12 ACSP2504N 2100 0.4 -53 12 C3 C8,C15,C32
0.5 - 18 ACSP2572N 1800 1.5 -52 12 C3 C15,C32
1 - 18 ACSP2759N 1500 1.25 -50 20 C3 C15,C32
2 - 18 ACSP2506N 1800 1.5 -51 12 C3 C15,C32
6 - 18 ACSP2523N 1800 1.0 -51 12 C3 C15,C32
12 - 18 ACSP2505N 2000 0.6 -52 12 C3 C15,C32
NOTES:
1) Standard output polarity is negative. If positive output is required, substitute “P” for “N” in part number.
2) Measured into an open circuit load (>10k ohm).
3) VSWR measured at or below -20dBm input power level.
4) Video capacitance is used for RF bypass. This value can be changed if required for video response time or other considerations.
Contact the factory if value other than those shown are needed.
5) Standard bias is 100 microamps.
6) Zero bias schottky versions are available for most of listed biased schottky models with only minor differences in specifications.
a. The zero bias schottky has an impedance of several thousand ohms.
b. Zero bias schottky detectors exhibit less sensitive TSS due to the high diode impedance (typically a 3dB reduction).
c. The temperature performance of the zero bias schottky is poor when operating at low input power levels. This difference
becomes small at high levels (above 0dBm input power). The part number of zero bias versions includes a “Z” following the
polarity indicator.
The ACSP series of high sensitivity detectors exhibit superior electrical and
environmental reliability characteristics. They contain hermetically sealed
modules, internal RF matching, DC return, and RF bypass capacitor. In
addition, the video port is protected from static or transient voltages. This
feature prevents damage due to handling (usually static) or system video
transients. Models may be chosen for broadband RF performance or for
optimized narrow bands.
BIASED COAXIAL SCHOTTKY DETECTORS
611 Industrial Way West, Eatontown, NJ 07724 tel: 732-460-0212 fax: 732-460-0214 sales@advanced-control.com www.advanced-control.com
ENVIRONMENTAL SPECIFICATIONS: SCREENING :
MIL-E-5400, MIL-STD-202, MIL-E-16400 Standard Screening:
Operating Temp: -65°C to +125°C Internal Visual per MIL-STD-883, Method 2017
Storage Temp: -65°C to +150°C Temperature Cycle: -65°C to +100°C, 10 cycles
Humidity: MIL-STD-202F, M103, Cond B Optional High-Rel Screening (Ref MIL-PRF-38534):
Shock: MIL-STD-202F, M213, Cond B Internal Visual per MIL-STD-883, Method 2017
Altitude: MIL-STD-202F, M105, Cond B Stabilization Bake per MIL-STD-883, Method 1008
Vibration : MIL-STD-202F, M204, Cond B Temperature Cycle per MIL-STD-883, Method 1010
Thermal Shock: MIL-STD-202F, M107, Cond A Constant Acceleration per MIL-STD-883, Method 2001
Temperature Cycle: MIL-STD-202F, M105C, Cond D Burn-in per MIL-STD-883, Method 1015
Maximum Input Power: +20dBm Leak Test per MIL-STD-883, Method 1014
External Visual per MIL-STD-883, Method 2009
CASE STYLE C3 CASE STYLE C8
CASE STYLE C15 CASE STYLE C32
Part Number Ordering Information: Example: ACSP2503NZC3X20
ACSP2503: Biased Coaxial Schottky Detector, 4 - 8GHz
N: Negative output polarity
Z: Zero bias version (omit for biased version)
C3: Package type
X: No video protection (omit for inclusion of video protection)
20: 20pF custom output capacitance (omit for standard value)
SPB-0205
Ø0.312
1.32±0.020
SMA
MALE
(INPUT)
SMA
FEMALE
(OUTPUT)
2.80±0.020
BNC
FEMALE
(OUTPUT)
Ø0.625
TYPE-N
MALE
(INPUT)
BNC
FEMALE
(OUTPUT)
SMA
MALE
(INPUT)
2.00
0.43
0.42
Ø0.500
Ø0.312
SMA
FEMALE
(OUTPUT)
SMA
MALE
(INPUT)
1.16±0.020
