White Electronic Designs WMF128K8-XXX5 128Kx8 MONOLITHIC FLASH, SMD 5962-96690 FEATURES Access Times of 50*, 60, 70, 90, 120, 150ns Organized as 128Kx8 Packaging * 32 lead, Hermetic Ceramic, 0.400" SOJ (Package 101) Commercial, Industrial and Military Temperature Ranges 5 Volt Programming. 5V 10% Supply. * 32 pin, Hermetic Ceramic, 0.600" DIP (Package 300) Low Power CMOS Embedded Erase and Program Algorithms * 32 lead, Flatpack (Package 220) TTL Compatible Inputs and CMOS Outputs * 32 lead, Formed Flatpack (Package 221) Page Program Operation and Internal Program Control Time. * 32 pin, Rectangular Ceramic Leadless Chip Carrier (Package 601) This product is subject to change without notice. 100,000 Erase/Program Cycles Minimum Sector Erase Architecture Note: For programming information refer to Flash Programming 1M5 Application Note. * 8 equal size sectors of 16KBytes each * The access time of 50ns is available in Industrial and Commercial temperature ranges only. * Any combination of sectors can be concurrently erased. Also supports full chip erase WE# VCC NC 4 3 2 1 32 31 30 A14 A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 Pin Description A0-16 I/O0-7 CS# OE# WE# VCC VSS 5 29 6 28 7 27 8 26 25 9 10 24 11 23 12 22 13 21 14 15 16 17 18 19 20 I/O4 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O3 VCC WE# NC A14 A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 VSS 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 I/O2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A16 Top View A15 32 CLCC Top View A12 32 DIP 32 CSOJ 32 Flatpack I/O1 NC A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS Pin Configuration For WMF128K8-XCLX5 NC Pin Configuration For WMF128K8-XXX5 Address Inputs Data Input/Output Chip Select Output Enable Write Enable +5.0V Power Ground White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 1 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs ABSOLUTE MAXIMUM RATINGS (1) Parameter Operating Temperature Supply Voltage (VCC) Signal Voltage Range (any pin except A9) (2) Storage Temperature Range Lead Temperature (soldering, 10 seconds) Data Retention Mil Temp Endurance (write/erase cycles) (Mil Temp) A9 Voltage for sector protect (VID) (3) WMF128K8-XXX5 RECOMMENDED OPERATING CONDITIONS Unit C V V C C years cycles V -55 to +125 -2.0 to +7.0 -2.0 to +7.0 -65 to +150 +300 10 10,000 min -2.0 to +14.0 Parameter Supply Voltage Input High Voltage Input Low Voltage Operating Temp. (Mil.) Operating Temp. (Ind.) A9 Voltage for Sector Protect Symbol VCC VIH VIL TA TA VID Min 4.5 2.0 -0.5 -55 -40 11.5 Max 5.5 VCC + 0.5 +0.8 +125 +85 12.5 Unit V V V C C V CAPACITANCE NOTES: 1. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may overshoot VSS to -2.0 V for periods of up to 20ns. Maximum DC voltage on output and I/O pins is VCC + 0.5V. During voltage transitions, outputs may overshoot to Vcc + 2.0 V for periods of up to 20ns. 3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is +13.5V which may overshoot to 14.0 V for periods up to 20ns. TA = +25C Parameter Address Input capacitance Output Enable capacitance Write Enable capacitance Chip Select capacitance Data I/O capacitance Symbol CAD COE CWE CCS CI/O Conditions Max Unit VI/O = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VI/O = 0 V, f = 1.0 MHz 15 pF This parameter is guaranteed by design but not tested. DC CHARACTERISTICS -- CMOS COMPATIBLE VCC = 5.0V, VSS = 0V, -55C TA +125C Parameter Input Leakage Current Output Leakage Current VCC Active Current for Read (1) VCC Active Current for Program or Erase (2) VCC Standby Current Output Low Voltage Output High Voltage Output High Voltage Low VCC Lock-Out Voltage Symbol ILI ILO ICC1 ICC2 ICC3 VOL VOH1 VOH2 VLKO Conditions VCC = 5.5, VIN = GND to VCC VCC = 5.5, VIN = GND to VCC CS# = VIL, OE# = VIH CS# = VIL, OE# = VIH VCC = 5.5, CS# = VIH, f = 5MHz IOL = 8.0 mA, VCC = 4.5 IOH = -2.5 mA, VCC = 4.5 IOH = -100 A, VCC = 4.5 Min Max 10 10 35 50 1.6 0.45 0.85 x VCC VCC - 0.4 3.2 Unit A A mA mA mA V V V V NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz). The frequency component typically is less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V AC TEST CONDITIONS AC TEST CIRCUIT Parameter Input Pulse Levels Input Rise and Fall Input and Output Reference Level Output Timing Reference Level I OL Current Source VZ D.U.T. 1.5V (Bipolar Supply) C eff = 50 pf Typ VIL = 0, VIH = 3.0 5 1.5 1.5 Unit V ns V V Notes: VZ is programmable from -2V to +7V. IOL & IOH programmable from 0 to 16mA. Tester Impedance Z0 = 75 . VZ is typically the midpoint of VOH and VOL. IOL & IOH are adjusted to simulate a typical resistive load circuit. ATE tester includes jig capacitance. I OH Current Source White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 2 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 AC CHARACTERISTICS - WRITE/ERASE/PROGRAM OPERATIONS, WE# CONTROLLED VCC = 5.0V, VSS = 0V, -55C TA +125C Parameter Symbol Write Cycle Time Chip Select Setup Time Write Enable Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time Chip Select Hold Time Write Enable Pulse Width High Duration of Byte Programming Operation (min) Sector Erase Time Read Recovery Time before Write VCC Set-up Time Chip Programming Time Output Enable Setup Time Output Enable Hold Time (1) -50 tAVAV tWC tELWL tCS tWLWH tWP tAVWH tAS tDVWH tDS tWHDX tDH tWHAX tAH tWHEH tCH tWHWL tWPH tWHWH1 tWHWH2 tGHWL tVCS Min 50 0 25 0 25 0 40 0 20 14 2.2 0 50 tOES tOEH 0 10 -60 Max 60 Min 60 0 30 0 30 0 45 0 20 14 2.2 0 50 12.5 -70 Max 60 Min 70 0 35 0 30 0 45 0 20 14 2.2 0 50 12.5 -90 Max 60 Min 90 0 45 0 45 0 45 0 20 14 2.2 0 50 12.5 0 10 0 10 -120 Max 60 Min 120 0 50 0 50 0 50 0 20 14 2.2 0 50 12.5 0 10 -150 Max 60 Min 150 0 50 0 50 0 50 0 20 14 2.2 0 50 12.5 0 10 0 10 Max Unit ns ns ns ns ns ns ns ns ns s 60 sec ms s 12.5 sec ns ns NOTES: 1. For Toggle and Data# Polling. AC CHARACTERISTICS - READ ONLY OPERATIONS VCC = 5.0V, VSS = 0V, -55C TA +125C Parameter Read Cycle Time Address Access Time Chip Select Access Time OE# to Output Valid Chip Select to Output High Z (1) OE# High to Output High Z (1) Output Hold from Address, CS# or OE# Change, whichever is First Symbol tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX tRC tACC tCE tOE tDF tDF tOH -50 Min 50 -60 Max Min 60 50 50 25 20 20 -70 Max Min 70 60 60 30 20 20 0 0 -90 Max Min 90 70 70 35 20 20 0 -120 Max Min 120 90 90 40 25 25 0 -150 Max Min 150 120 120 50 30 30 0 Unit Max 150 150 55 35 35 0 ns ns ns ns ns ns ns NOTES: 1. Guaranteed by design, but not tested White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 3 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 AC CHARACTERISTICS - WRITE/ERASE/PROGRAM OPERATIONS,CS# CONTROLLED VCC = 5.0V, VSS = 0V, -55C TA +125C Parameter Write Cycle Time WE# Setup Time CS# Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time WE# Hold from WE# High CS# Pulse Width High Duration of Programming Operation Duration of Erase Operation Read Recovery before Write Chip Programming Time Symbol tAVAV tWLEL tELEH tAVEL tDVEH tEHDX tELAX tEHWH tEHEL tWHWH1 tWHWH2 tGHEL tWC tWS tCP tAS tDS tDH tAH tWH tCPH -50 Min -60 Max Min -70 Max Min -90 Max Min -120 Max Min -150 Max Min Max Unit 50 60 70 90 120 150 0 0 0 0 0 0 ns ns 25 30 35 45 50 50 ns 0 0 0 0 0 0 ns 25 30 30 45 50 50 ns 0 0 0 0 0 0 ns 40 45 45 45 50 50 ns 0 0 0 0 0 0 ns 20 20 20 20 20 20 ns 14 2.2 14 60 0 2.2 14 60 0 12.5 2.2 14 60 0 12.5 2.2 14 60 0 12.5 2.2 14 60 0 12.5 2.2 s 60 sec 12.5 sec 0 12.5 ns White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 4 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 Outputs WE# OE# CS# Addresses High Z tACC tCE tOE Addresses Stable tRC Output Valid tOH tDF High Z AC WAVEFORMS FOR READ OPERATIONS White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 5 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 A0H tCPH tDH 5.0 V tDS Data OE# CS# tWS tWC WE# NOTES: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7# is the output of the complement of the data written to each chip. 4. DOUT is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. Addresses 5555H tGHEL tCP tAS PA PD t AH tWHWH1 Data# Polling PA D7 # DOUT WRITE/ERASE/PROGRAM OPERATION, WE# CONTROLLED White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 6 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 5555H AAAAH tDS tDH tWPH tVCS VCC Data WE# OE# Addresses NOTE: 1. SA is the sector address for Sector Erase. CS# tGHWL tCS tWP tAS 2AAAH 5555H tAH 5555H 8080H 5555H AAAAH 2AAAH 5555H SA 1010H/3030H AC WAVEFORMS CHIP/SECTOR ERASE OPERATIONS White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 7 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 I/O0-15 Valid Data I/O0-6 and I/O8-14 Invalid t OE I/O7 and I/O15 Valid Data I/O0-6 and I/O8-14 I/O7 and I/O15 Data WE# OE# CS# t CH tOEH tCE t OE tWHWH 1 or 2 I/O7 # and I/O15 # t OH t DF High Z AC WAVEFORMS FOR DATA# POLLING DURING EMBEDDED ALGORITHM OPERATIONS White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 8 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 tDH A0H tCPH 5.0 V tDS Data CS# OE# tWS tWC WE# Addresses 5555H tGHEL tCP tAS PA PD t AH tWHWH1 Data# Polling PA D7 # DOUT ALTERNATE CS# CONTROLLED PROGRAMMING OPERATION TIMINGS NOTES: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7# is the output of the complement of the data written to each chip. 4. DOUT is the output of the data written to the device. 5. Figure indicates the last two bus cycles of a four bus cycle sequence. White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 9 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 PACKAGE 101: 32 LEAD, CERAMIC SOJ 3.96 (0.156) MAX 21.1 (0.830) 0.25 (0.010) 0.89 (0.035) Radius TYP 0.2 (0.008) 0.05 (0.002) 11.3 (0.442) 0.30 (0.012) 9.55 (0.376) 0.25 (0.010) 1.27 (0.050) 0.25 (0.010) PIN 1 IDENTIFIER 1.27 (0.050) TYP 19.1 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES PACKAGE 220: 32 LEAD, CERAMIC FLATPACK 20.83 (0.820) 0.25 (0.010) PIN 1 IDENTIFIER 2.60 (0.102) MAX 10.41 (0.410) 0.13 (0.005) 10.16 (0.400) 0.51 (0.020) 0.43 (0.017) 0.05 (0.002) 0.127 (0.005) + 0.05 (0.002) - 0.025 (0.001) 1.27 (0.050) TYP 19.05 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 10 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 PACKAGE 221: 32 LEAD, FORMED CERAMIC FLATPACK 3.35 (0.132) MAX 20.83 (0.820) 0.25 (0.010) 0.15 (0.006) TYP 1.27 (0.050) TYP 10.41 (0.410) 0.13 (0.005) 13.47 (0.530) 0.13 (0.005) + + 0.43 (0.017) 0.05 (0.002) 1.27 (0.050) TYP 0.63 (0.025) TYP 0/ -4 19.05 (0.750) TYP 1.52 (0.060) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES PACKAGE 300: 32 PIN, CERAMIC DIP, SINGLE CAVITY SIDE BRAZED 42.4 (1.670) 0.4 (0.016) 15.04 (0.592) 0.3 (0.012) 4.34 (0.171) 0.79 (0.031) PIN 1 IDENTIFIER 3.2 (0.125) MIN 0.84 (0.033) 0.4 (0.014) 2.5 (0.100) TYP 1.27 (0.050) 0.1 (0.005) 0.46 (0.018) 0.05 (0.002) 0.25 (0.010) 0.05 (0.002) 15.25 (0.600) 0.25 (0.010) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 11 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 PACKAGE 601: 32 PIN, RECTANGULAR CERAMIC LEADLESS CHIP CARRIER 7.62 (0.300) TYP 3.81 (0.150) TYP 5.08 (0.200) TYP 0.56 (0.022) 0.71 (0.028) 10.16 (0.400) TYP PIN 1 0.38 (0.015) x 45 PIN 1 IDENTIFIER 11.25 (0.443) 11.60 (0.457) 1.63 (0.064) 2.54 (0.100) 13.79 (0.543) 14.15 (0.557) 1.02 (0.040) x 45 3 PLACES 32PinCLCCpkgdim.eps ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 12 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs WMF128K8-XXX5 ORDERING INFORMATION W M F 128K8 - XXX X X 5 X LEAD FINISH: Blank = Gold plated leads A = Solder dip leads VPP PROGRAMMING VOLTAGE 5 = 5V DEVICE GRADE: Q = MIL-STD-883 Compliant M = Military Screened -55C to +125C I = Industrial -40C to +85C C = Commercial 0C to +70C PACKAGE TYPE: DE = 32 Lead Ceramic SOJ (Package 101) C = 32 Pin Ceramic DIP (Package 300) FE = 32 Lead Ceramic Flatpack (Package 220) FF = 32 Lead Formed Ceramic Flatpack (Package 221) CL = 32 Pin rectangular Ceramic Leadless Chip Carrier (Package 601) ACCESS TIME (ns) ORGANIZATION, 128K x 8 Flash MONOLITHIC WHITE ELECTRONIC DESIGNS CORP. White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 13 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PACKAGE WMF128K8-XXX5 DEVICE TYPE SECTOR SIZE SPEED SMD NO. 128K x 8 Flash Monolithic 16KByte 150ns 32 pin DIP (C) 5962-96690 01HYX 128K x 8 Flash Monolithic 16KByte 120ns 32 pin DIP (C) 5962-96690 02HYX 128K x 8 Flash Monolithic 16KByte 90ns 32 pin DIP (C) 5962-96690 03HYX 128K x 8 Flash Monolithic 16KByte 70ns 32 pin DIP (C) 5962-96690 04HYX 128K x 8 Flash Monolithic 16KByte 60ns 32 pin DIP (C) 5962-96690 05HYX 128K x 8 Flash Monolithic 16KByte 150ns 32 lead SOJ (DE) 5962-96690 01HXX 128K x 8 Flash Monolithic 16KByte 120ns 32 lead SOJ (DE) 5962-96690 02HXX 128K x 8 Flash Monolithic 16KByte 90ns 32 lead SOJ (DE) 5962-96690 03HXX 128K x 8 Flash Monolithic 16KByte 70ns 32 lead SOJ (DE) 5962-96690 04HXX 128K x 8 Flash Monolithic 16KByte 60ns 32 lead SOJ (DE) 5962-96690 05HXX 128K x 8 Flash Monolithic 16KByte 150ns 32 lead Flatpack (FE) 5962-96690 01HTX 128K x 8 Flash Monolithic 16KByte 120ns 32 lead Flatpack (FE) 5962-96690 02HTX 128K x 8 Flash Monolithic 16KByte 90ns 32 lead Flatpack (FE) 5962-96690 03HTX 128K x 8 Flash Monolithic 16KByte 70ns 32 lead Flatpack (FE) 5962-96690 04HTX 128K x 8 Flash Monolithic 16KByte 60ns 32 lead Flatpack (FE) 5962-96690 05HTX 128K x 8 Flash Monolithic 16KByte 150ns 32 lead Formed Flatpack (FF) 5962-96690 01HUX 128K x 8 Flash Monolithic 16KByte 120ns 32 lead Formed Flatpack (FF) 5962-96690 02HUX 128K x 8 Flash Monolithic 16KByte 90ns 32 lead Formed Flatpack (FF) 5962-96690 03HUX 128K x 8 Flash Monolithic 16KByte 70ns 32 lead Formed Flatpack (FF) 5962-96690 04HUX 128K x 8 Flash Monolithic 16KByte 60ns 32 lead Formed Flatpack (FF) 5962-96690 05HUX White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 14 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com