Model 114 Dual-In-Line Stratum 3 OCXO Frequency Stability to Stratum 3 of GR-1244 Low Cost ASIC Based Design Very Low Phase Jitter: < 1 pSec +3.3Vdc or +5.0Vdc Operation Precision Low Aging "AT" Cut Crystal Through-Hole or Surface Mount Configuration 6/6 RoHS Compliant Electrical Characteristics Parameter Sym Power Requirements Power Supply Vcc Turn-On Power Pmax Steady State Power Pss Warm-Up Time Twu Frequency Stabilities Center Frequency fnom Initial Tolerance fcal Freq. vs. Temp. f/Temp Freq. vs. Voltage Freq. vs Time (Aging) f/Vcc f/Time 24 Hour Holdover Stability f/24Hr Total Free-Running Accuracy Electronic Frequency Adjust (Optional) f/Life f/Vc Conditions Min Typical Max Unit 5% 114L 5% 114S Vcc=Max. Std. Load Vcc=Max. Std. Load @ +25C To within 0.3ppm @ +25C 3.135 4.75 3.30 5.0 3.465 5.25 Vdc Vdc 3.5 4.0 W Ta=+25C (At time of Shipment) 0 to +70C -40 to +85C Vcc 5% Per day 20 years Inclusive of Temp., Supply Variation and 24Hrs. Aging All Cond. for 20 Yrs. (Ref. to fnom) fmin @ Vc=0V fmax @ Vc=Vcc fnom @Vc=0.5Vcc Sym Vo @ 50% Level Rise/Fall Times Load tr, tf RL 20% to 80% Output to Ground Phase Noise @ fo=20MHz Pn Offset = 10Hz 100Hz 1kHz 10kHz 100kHz 12kHz to 20MHz Bandwidth Logic "1" Logic "0" W 5 8 Waveform: CMOS Output Symmetry Amplitude Phase Jitter 1.5 10 12.8 16.384 19.44 20 0.1 38.88 0.075 0.150 0.05 0.005 2.5 0.20 0.125 0.250 MHz ppm ppm ppm ppm 0.37 ppm 4.6 ppm 9.2 40 0.9Vcc minutes ppm 50 6 10k // 15pF 60 0.1Vcc 10 % V V ns 1.0 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS -80 -115 -135 -140 -143 CTS 171 Covington Dr. Bloomingdale, IL 60108 800-757-6686 www.ctscorp.com Document No. 114 Data Sheet Page 1 of 2 Rev X8 Model 114 Dual-In-Line Stratum 3 OCXO Through-Hole Outline Surface Mount Outline Pin 1 7 8 14 Function Elec. Freq. Adj. or NC Ground Output +Vcc Supply Environmental / Mechanical Specifications Storage Temperature: Reflow Soldering: Shock: Vibration: Case: Seal: Lead Finish, Thru-Hole Pad Finish, Surface Mt. MSL: -55 to +125C will withstand 240C for 20 Seconds 50 G's, 11 mSec. Pulse (3 Shocks/Axis) 10 G's peak, 10 to 500 Hz 4-Pin Dual-In-Line Resistance Weld Solder Coated, 96.5/3.5 Sn/Ag Gold Flash, <10 micro inch over Ni plated Cu Level 1 Model 114 Standard Options Frequency in MHz Model 114 Supply Voltage L = +3.3Vdc S = +5.0Vdc Oper. Temp. Range A = 0 to +70C B = -40 to +85C ___.________ Example: 114SBFT20.0000 Electronic Freq. Control F = Fixed - No Adjust V = Elect. Freq. Adjust Package Style T = Through-Hole S = Surface Mount CTS 171 Covington Dr. Bloomingdale, IL 60108 800-757-6686 www.ctscorp.com Document No. 114 Data Sheet Page 2 of 2 Rev X8