© Semiconductor Components Industries, LLC, 2009
October, 2009 Rev. 12
1Publication Order Number:
NCV8505/D
NCV8505 Series
Micropower 400 mA
LDO Linear Regulators
with ENABLE, DELAY,
and RESET
The NCV8505 is a family of precision micropower voltage
regulators. Their output current capability is 400 mA. The family has
output voltage options for Adjustable, 2.5 V, 3.3 V and 5.0 V.
The output voltage is accurate within ± 2.0% with a maximum
dropout voltage of 0.6 V at 400 mA. Low quiescent current is a feature
drawing less than 1.0 mA with ENABLE = 0 V. With ENABLE = 5.0 V,
the part only draws 200 mA with 100 mA load. This part is ideal for any
and all battery operated microprocessor equipment.
Microprocessor control logic includes an active RESET (with
DELAY).
The active RESET circuit operates correctly at an output voltage as
low as 1.0 V. The RESET function is activated during the power up
sequence or during normal operation if the output voltage drops below
the regulation limits.
The regulator is protected against reverse battery, short circuit, and
thermal overload conditions. The device can withstand load dump
transients making it suitable for use in automotive environments. The
device has also been optimized for EMC conditions.
Features
Output Voltage Options: Adjustable, 2.5 V, 3.3 V, 5.0 V
± 2.0% Output
Low < 1.0 mA Sleep Current
Low 200 mA Quiescent Current
Fixed or Adjustable Output Voltage
Active RESET
ENABLE
400 mA Output Current Capability
Fault Protection
+60 V Peak Transient Voltage
15 V Reverse Voltage
Short Circuit
Thermal Overload
NCV Prefix for Automotive and Other Applications Requiring Site
and Change Control
AEC Qualified
PPAP Capable
These are PbFree Devices
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
ORDERING INFORMATION
http://onsemi.com
x = Voltage Ratings as Indicated Below:
A = Adjustable
2 = 2.5 V
3 = 3.3 V
5 = 5.0 V
A = Assembly Location
WL = Wafer Lot
Y = Year
WW = Work Week
G=PbFree Package
MARKING
DIAGRAM
D2PAK7
DPS SUFFIX
CASE 936AB
NC
V8505x
AWLYWWG
1
1
NCV8505 Series
http://onsemi.com
2
PIN CONNECTIONS
FIXED OUTPUTADJUSTABLE OUTPUT
Tab = GND
Lead 1. DELAY
2. ENABLE
3. RESET
4. GND
5. VADJ
6. VOUT
7. VIN
1
Tab = GND
Lead 1. DELAY
2. ENABLE
3. RESET
4. GND
5. SENSE
6. VOUT
7. VIN
1
VOUT
GND
VIN
NCV8505
33 mF
5.1 k
RRST
RESET
10 mF
Microprocessor
DELAY
CDELAY
VBAT VDD
Figure 1. Application Diagram
VADJ
(Adjustable
Output Only)
I/O
ENABLE
SENSE
(Fixed Output Only)
IQ
NCV8505 Series
http://onsemi.com
3
MAXIMUM RATINGS
Rating Value Unit
VIN (DC) 15 to 45 V
Peak Transient Voltage (46 V Load Dump @ VIN = 14 V) 60 V
Operating Voltage 45 V
VOUT (DC) 0.3 to 16 V
Voltage Range (RESET, DELAY) 0.3 to 10 V
Input Voltage Range: VADJ 0.3 to 16 V
Input Voltage Range (ENABLE) 0.3 to 10* V
ESD Susceptibility (Human Body Model)
(Machine Model)
4.0
200
kV
V
Junction Temperature, TJ40 to +150 °C
Storage Temperature, TS55 to 150 °C
Package Thermal Resistance, 7 Lead D2PAK JunctiontoCase, RqJC
JunctiontoAmbient, RqJA
2.0
1050**
°C/W
°C/W
Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1) 240 peak (Note 2) °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 60 second maximum above 183°C.
2. 5°C/+0°C allowable conditions.
*Reference Figure 16 for switchedbattery ENABLE application.
**Depending on thermal properties of substrate, RqJA = RqJC + RqCA.
ELECTRICAL CHARACTERISTICS (IOUT = 1.0 mA, ENABLE = 5.0 V, 40°C TJ 150°C; VIN = dependent on voltage option (Note 3);
unless otherwise specified.)
Characteristic Test Conditions Min Typ Max Unit
Output Stage
Output Voltage for 2.5 V Option (VO)6.5 V < VIN < 16 V, 1.0 mA IOUT 400 mA
4.5 V < VIN < 26 V, 1.0 mA IOUT 400 mA
2.450
2.425
2.5
2.5
2.550
2.575
V
V
Output Voltage for 3.3 V Option (VO)7.3 V < VIN < 16 V, 1.0 mA IOUT 400 mA
4.5 V < VIN < 26 V, 1.0 mA IOUT 400 mA
3.234
3.201
3.3
3.3
3.366
3.399
V
V
Output Voltage for 5.0 V Option (VO)9.0 V < VIN < 16 V, 1.0 mA IOUT 400 mA
6.0 V < VIN < 26 V, 1.0 mA IOUT 400 mA
4.90
4.85
5.0
5.0
5.10
5.15
V
V
Output Voltage for Adjustable Option (VO) VOUT = VADJ (Unity Gain)
6.5 V < VIN < 16 V, 1.0 mA < IOUT < 400 mA
4.5 V < VIN < 26 V, 1.0 mA < IOUT < 400 mA
1.274
1.261
1.300
1.300
1.326
1.339
V
V
Dropout Voltage (VIN VOUT)
(5.0 V and Adj. > 5.0 V Options Only)
IOUT = 400 mA
IOUT = 1.0 mA
400
30
600
150
mV
mV
Load Regulation VIN = 14 V, 5.0 mA IOUT 400 mA 30 5.0 30 mV
Line Regulation (2.5 V, 3.3 V, and
Adjustable Options)
4.5 V < VIN < 26 V, IOUT = 1.0 mA 5.0 25 mV
Line Regulation (5.0 V Option) 6.0 V < VIN < 26 V, IOUT = 1.0 mA 5.0 25 mV
Quiescent Current, (IQ) Active Mode IOUT = 100 mA, VIN = 12 V
IOUT = 75 mA, VIN = 14 V
IOUT 400 mA, VIN = 14 V
200
2.5
25
350
5.0
45
mA
mA
mA
Quiescent Current, (IQ) Sleep Mode ENABLE = 0 V, VIN = 12 V, 40°C TJ 125°C 1.0 mA
Current Limit 425 800 mA
Short Circuit Output Current VOUT = 0 V 100 500 mA
Thermal Shutdown (Guaranteed by Design) 150 180 °C
3. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
NCV8505 Series
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (continued) (IOUT = 1.0 mA, ENABLE = 5.0 V, 40°C TJ 150°C; VIN = dependent on
voltage option (Note 4); unless otherwise specified.)
Characteristic Test Conditions Min Typ Max Unit
Reset Function (RESET)
RESET Threshold for 2.5 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
2.35
2.30
25
1.0 × VO
V
V
mV
RESET Threshold for 3.3 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
3.10
3.00
35
1.0 × VO
V
V
mV
RESET Threshold for 5.0 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 6.0 V (Note 6)
VOUT Increasing
VOUT Decreasing
4.70
4.60
50
1.0 × VO
V
V
mV
RESET Threshold for Adjustable Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
1.22
1.19
10
1.0 × VO
V
V
mV
RESET Output Voltage
Low (VRLO)
VIN = Minimum (Note 6) (Note 7)
1.0 V VOUT VRL, RRESET = 5.1 k
0.1 0.4 V
DELAY Switching Threshold (VDT)
(2.5 V, 3.3 V, and 5.0 V Options)
VIN = Minimum (Note 6) (Note 7) 1.4 1.8 2.2 V
DELAY Switching Threshold (VDT)
(Adjustable Option)
VIN = Minimum (Note 6) (Note 7) 1.0 1.3 1.6 V
DELAY Low Voltage VIN = Minimum (Note 6) (Note 7)
VOUT < RESET Threshold Low(min)
0.2 V
DELAY Charge Current VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT > VRH
2.5 4.0 5.5 mA
DELAY Discharge Current VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT < VRL
5.0 mA
Voltage Adjust (Adjustable Output only)
Input Current VADJ = 1.25 V, VIN = Minimum (Note 6) (Note 7) 0.5 0.5 mA
ENABLE
Input Threshold Low, VIN = 14 V (Note 6)
High, VIN = 14 V (Note 6)
2.0
1.0
V
V
Input Current ENABLE = 5.0 V, VIN = 14 V (Note 6) 30 75 mA
4. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
5. For VIN 4.5 V, a RESET = Low may occur with the output in regulation.
6. Part is guaranteed by design to meet specification over the entire VIN voltage range, but is production tested only at the specified VIN voltage.
7. Minimum VIN = 4.5 V for 2.5 V, 3.3 V, and Adjustable options. Minimum VIN = 6.0 V for 5.0 V option.
NCV8505 Series
http://onsemi.com
5
PACKAGE PIN DESCRIPTION, ADJUSTABLE OUTPUT
Pin Number Pin Symbol Function
1 DELAY Timing capacitor for RESET function.
2 ENABLE ENABLE control for the IC. A high powers the device up.
3 RESET Active reset (accurate to VOUT 1.0 V)
4 GND Ground. All GND leads must be connected to Ground.
5 VADJ Voltage Adjust. A resistor divider from VOUT to this lead sets the output voltage.
6 VOUT ±2.0%, 400 mA output.
7 VIN Input Voltage.
PACKAGE PIN DESCRIPTION, FIXED OUTPUT
Pin Number Pin Symbol Function
1 DELAY Timing capacitor for RESET function.
2 ENABLE ENABLE control for the IC. A high powers the device up.
3 RESET Active reset (accurate to VOUT 1.0 V)
4 GND Ground. All GND leads must be connected to Ground.
5 SENSE Kelvin connection which allows remote sensing of output voltage for improved regulation. If
remote sensing is not desired, connect to VOUT
.
6 VOUT ±2.0%, 400 mA output.
7 VIN Input Voltage.
NCV8505 Series
http://onsemi.com
6
VIN
RESET
VOUT
DELAY
Figure 2. Block Diagram
GND
Current Source
(Circuit Bias)
Current Limit
Sense
Error Amplifier
VBG
IBIAS
VBG
IBIAS
IBIAS
+
+
Bandgap
Reference
Thermal
Protection
1.8 V (Fixed Versions)
1.3 V (Adjustable Version)
4.0 mA15 k
Adjustable
Version only
VADJ
ENABLE
Fixed Versions only
SENSE
+
1.5 V
+
VBG 18 mV
NCV8505 Series
http://onsemi.com
7
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 3. 5 V Output Voltage vs. Temperature
0
0
Iout, OUTPUT CURRENT (mA)
50 100 150 200 250
DROPOUT VOLTAGE (mV)
400
300
200
100
5 V and Adj. > 5 V options only
Figure 4. 3.3 V Output Voltage vs. Temperature
Figure 5. 2.5 V Output Voltage vs. Temperature Figure 6. Dropout Voltage vs. Output Current
INPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
Figure 7. Output Voltage vs. Input Voltage Figure 8. Output Voltage vs. Input Voltage
500
600
125 °C
40
Vout, OUTPUT VOLTAGE (V)
4.90
TEMPERATURE (°C)
4.98
5.00
5.08
5.10
20 1400 20 40 60 80 120100
VOUT = 5.0 V
VIN = 14 V
IOUT = 5.0 mA
4.96
5.06
4.94
5.04
4.92
5.02
160 40
Vout, OUTPUT VOLTAGE (V)
3.23
TEMPERATURE (°C)
3.31
3.33
3.35
20 1400 20 40 60 80 120100
VOUT = 3.3 V
VIN = 14 V
IOUT = 5.0 mA
3.29
3.27
3.25
160
40
Vout, OUTPUT VOLTAGE (V)
2.45
TEMPERATURE (°C)
2.49
2.50
2.54
2.55
20 1400 20 40 60 80 120100
VOUT = 2.5 V
VIN = 14 V
IOUT = 5.0 mA
2.48
2.53
2.47
2.52
2.46
2.51
160 300 350 400
25 °C
40 °C
IOUT = 1 mA
INPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0 4 8 12162024
125 °C
25 °C
40 °C
0.0
0.5
1.0
1.5
2.0
2.5
3.0
1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
IOUT = 1 mA
125 °C25 °C40 °C
NCV8505 Series
http://onsemi.com
8
TYPICAL PERFORMANCE CHARACTERISTICS
0.01
Iout, OUTPUT CURRENT (mA)
50 100 150 200 250 350 400
100
ESR (W)
10
1.0
0.1
0
Figure 9. Output Stability with Output Voltage Change Figure 10. Output Stability with Output Capacitor
Change
300
VIN = 14 V
CVOUT = 10 mF
Unstable Region
Stable Region
2.5 V
3.3 V
5.0 V
0.1
Iout, OUTPUT CURRENT (mA)
50 100 150 200 250 350 400
100
ESR (W)
10
1.0
0 300
5 V version
Unstable Region
Stable Region CVOUT = 0.1 mF
Unstable Region
CVOUT = 33 mF*
*There is no unstable lower
region for the 33 mF capacitor
Figure 11. Quiescent Current vs. Output Current Figure 12. Quiescent Current vs. Output Current
Figure 13. Quiescent Current vs. Input Voltage
0
IQ, QUIESCENT CURRENT (mA)
0.0
IOUT
, OUTPUT CURRENT (mA)
0.2
0.4
0.6
0.8
1.0
1.2
2.0
5101520 3025
+25°C
+125°C
40°C
Figure 14. Quiescent Current vs. Input Voltage
35 40 5045
1.4
1.6
1.8
0
IQ, QUIESCENT CURRENT (mA)
0
IOUT
, OUTPUT CURRENT (mA)
10
20
30
40
50
60
50 100 150 200 300250
+25°C
+125°C
40°C
350 400 500450
6
IQ, QUIESCENT CURRENT (mA)
0
VIN, INPUT VOLTAGE (V)
2
4
6
8
10
12
810 12 14 1816
T = 25°C
Iout = 200 mA
20 22 2624
Iout = 100 mA
Iout = 50 mA
Iout = 10 mA
6
IQ, QUIESCENT CURRENT (mA)
175
VIN, INPUT VOLTAGE (V)
180
185
190
195
200
210
810 12 14 1816
T = 25°C
20 22 2624
Iout = 100 mA
205
NCV8505 Series
http://onsemi.com
9
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV8505 contains the microprocessor compatible
control function RESET (Figure 15).
Figure 15. Reset and Delay Circuit Wave Forms
VIN
VOUT
RESET
DELAY
(VDT)
Threshold
DELAY
Threshold
RESET
TdTd
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until VOUT is within 1.5% of the regulated output
voltage, or when VOUT drops out of regulation,and is lower
than 4.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for VOUT as low
as 1.0 V.
ENABLE Function
The part stays in a low IQ sleep mode when the ENABLE
pin is held low. The part has an internal pull down if the pin
is left floating.
The integrity of the ENABLE pin allows it to be tied to the
battery line through an external resistor. It will withstand
load dump potentials in this configuration.
Figure 16. ENABLE Function
VIN VOUT
GND
NCV8505
ENABLE
VBAT
Up to 45 V
10 k
DELAY Function
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
The DELAY lead provides source current (typically 4.0 mA)
to the external DELAY capacitor during the following
proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
Voltage Adjust
Figure 17 shows the device setup for a user configurable
output voltage. The feedback to the VADJ pin is taken from
a voltage divider referenced to the output voltage. The loop
is balanced around the Unity Gain threshold (1.30 V
typical).
Figure 17. Adjustable Output Voltage
VOUT
VADJ
NCV8505 15 k
5.1 k
COUT
5.0 V
1.28 V
NCV8505 Series
http://onsemi.com
10
APPLICATION NOTES
SETTING THE DELAY TIME
The delay time is controlled by the Reset Delay Low
Voltage, Delay Switching Threshold, and the Delay Charge
Current. The delay follows the equation:
tDELAY +ƪCDELAY(Vdt *Reset Delay Low Voltage)ƫ
Delay Charge Current
Example:
Using CDELAY = 33 nF.
Assume reset Delay Low Voltage = 0.
Use the typical value for Vdt = 1.8 V (2.5 V, 3.3 V, and
5.0 V options).
Use the typical value for Delay Charge Current = 4.2 mA.
tDELAY +ƪ33 nF(1.8 *0)ƫ
4.2 mA+14 ms
STABILITY CONSIDERATIONS
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: startup
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures (25°C to 40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
The value for the output capacitor COUT shown in Figure 18
should work for most applications, however it is not
necessarily the optimized solution.
Figure 18. Test and Application Circuit Showing
Output Compensation
VIN VOUT
COUT**
33 mF
RRST
RESET
CIN*
0.1 mFNCV8505
*CIN required if regulator is located far from the power supply
filter.
**COUT required for stability. Capacitor must operate at minimum
temperature expected.
CALCULATING POWER DISSIPATION IN A
SINGLE OUTPUT LINEAR REGULATOR
The maximum power dissipation for a single output
regulator (Figure 19) is:
PD(max) +[VIN(max) *VOUT(min)]IOUT(max) (1)
)VIN(max)IQ
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
Once the value of PD(max) is known, the maximum
permissible value of RqJA can be calculated:
RqJA +150oC*TA
PD(2)
The value of RqJA can then be compared with those in the
package section of the data sheet. Those packages with
RqJA
s less than the calculated value in equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
SMART
REGULATOR®
IQ
Control
Features
IOUT
IIN
Figure 19. Single Output Regulator with Key
Performance Parameters Labeled
VIN VOUT
}
HEAT SINKS
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RqJA:
RqJA +RqJC )RqCS )RqSA (3)
where:
RqJC = the junctiontocase thermal resistance,
RqCS = the casetoheatsink thermal resistance, and
RqSA = the heatsinktoambient thermal resistance.
RqJC appears in the package section of the data sheet. Like
RqJA, it too is a function of package type. RqCS and RqSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data sheets
of heat sink manufacturers.
NCV8505 Series
http://onsemi.com
11
ORDERING INFORMATION
Device Output Voltage Package Shipping
NCV8505D2TADJG
Adjustable
D2PAK7
(PbFree) 50 Units / Rail
NCV8505D2TADJR4G D2PAK7
(PbFree) 750 Tape & Reel
NCV8505D2T25G
2.5 V
D2PAK7
(PbFree) 50 Units / Rail
NCV8505D2T25R4G D2PAK7
(PbFree) 750 Tape & Reel
NCV8505D2T33G
3.3 V
D2PAK7
(PbFree) 50 Units / Rail
NCV8505D2T33R4G D2PAK7
(PbFree) 750 Tape & Reel
NCV8505D2T50G
5.0 V
D2PAK7
(PbFree) 50 Units / Rail
NCV8505D2T50R4G D2PAK7
(PbFree) 750 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
NCV8505 Series
http://onsemi.com
12
PACKAGE DIMENSIONS
D
2
PAK7 (SHORT LEAD)
DPS SUFFIX
CASE 936AB01
ISSUE B
0.539
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
E0.380 0.420 9.65 10.67
D0.325 0.368 8.25 9.53
A0.170 0.180 4.32 4.57
b0.026 0.036 0.66 0.91
c2 0.045 0.055 1.14 1.40
e0.050 BSC 1.27 BSC
H0.579 13.69 14.71
L1
A1 0.000 0.010 0.00 0.25
c0.017 0.026 0.43 0.66
E
D
L1 c2
c
be
E1
D1
H
−−− 0.066 −−− 1.68
L0.058 0.078 1.47 1.98
M
L3 0.010 BSC 0.25 BSC
0 8 °°0 8 °°
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
RECOMMENDED
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH AND GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.005 MAXIMUM PER SIDE. THESE DIMENSIONS
TO BE MEASURED AT DATUM H.
4. THERMAL PAD CONTOUR OPTIONAL WITHIN
DIMENSIONS E, L1, D1, AND E1. DIMENSIONS
D1 AND E1 ESTABLISH A MINIMUM MOUNTING
SURFACE FOR THE THERMAL PAD.
D1 0.270 −−− 6.86 −−−
E1 0.245 −−− 6.22 −−−
A
DIMENSIONS: MILLIMETERS
0.424
7X
0.584
0.310
0.136
0.040 0.050
PITCH
SOLDERING FOOTPRINT*
A1
L3
B
H
L
M
DETAIL C
SEATING
PLANE
GAUGE
PLANE
A
7X
M
A
M
0.13 B
E/2
BSEATING
PLANE
A
A
DETAIL C
VIEW AA
M
A
M
0.10 B
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81357733850
NCV8505/D
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLC).
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative