Subminiature LED Lamps Technical Data HLMP-Pxxx Series HLMP-Qxxx Series HLMP-6xxx Series HLMP-70xx Series Features * Subminiature Flat Top Package Ideal for Backlighting and Light Piping Applications * Subminiature Dome Package Diffused Dome for Wide Viewing Angle Nondiffused Dome for High Brightness * TTL and LSTTL Compatible 5 Volt Resistor Lamps * Available in Six Colors * Ideal for Space Limited Applications * Axial Leads * Available with Lead Configurations for Surface Mount and Through Hole PC Board Mounting Description Flat Top Package The HLMP-Pxxx Series flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. The flat top lamps are also ideal for use as emitters in light pipe applications. Dome Packages The HLMP-6xxx Series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. High brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. Resistor Lamps The HLMP-6xxx Series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. Lead Configurations All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These include special surface mount lead configurations, gull wing, yoke lead or Zbend. Right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more information refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet. 2 Device Selection Guide Part Number: HLMP-xxxx DH AS High High Standard AlGaAs Efficiency Perf. Emerald Red Red Red Orange Yellow Green Green 6000 P105 P205 P405 P305 P505 P102 P202 P402 P302 P502 Q100 6300 Q400 6400 6500 Q105 6305 6405 Q150 7000 7019 Untinted, Nondiffused, Flat Top A Untinted, Diffused, Flat Top A Tinted, Diffused B 6505 Untinted, Nondiffused, High Brightness B 7040 Tinted, Diffused, Low Current B Nondiffused, Low Current B Q155 P605 Device Description[1] Device Outline Drawing Q600 6600 6700 6800 Tinted, Diffused, Resistor, 5 V, 10 mA B 6620 6720 6820 Diffused, Resistor, 5 V, 4 mA B Ordering Information HLMX-XXXX-X X X X X 4x4 Prod. Part Number Packaging Option Min. Iv Bin Color Bin Selection Max. Iv Bin 3 Package Dimensions (A) Flat Top Lamps 2.21 (0.087) 1.96 (0.077) 0.50 (0.020) REF. 1.40 (0.055) 1.65 (0.065) 11.68 (0.460) 10.67 (0.420) BOTH SIDES ANODE 1.65 (0.065) DIA. 1.91 (0.075) 0.20 (0.008) MAX. 1.14 (0.045) 1.40 (0.055) 0.63 (0.025) 0.38 (0.015) CATHODE 2.44 (0.096) 1.88 (0.074) 0.46 (0.018) 0.56 (0.022) CATHODE STRIPE 0.79 (0.031) MAX. 0.18 (0.007) 0.23 (0.009) 2.08 (0.082) 2.34 (0.092) 0.25 (0.010) MAX.* NOTE 2 NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. * REFER TO FIGURE 1 FOR DESIGN CONCERNS. Package Dimensions (cont.) (B) Diffused and Nondiffused 0.18 (0.007) 0.23 (0.009) 0.50 (0.020) REF. 11.68 (0.460) 10.67 (0.420) BOTH SIDES CATHODE 2.21 (0.087) 1.96 (0.077) 0.76 (0.030) R. 0.89 (0.035) 0.94 (0.037) 1.24 (0.049) 2.03 (0.080) 1.78 (0.070) 2.92 (0.115) MAX. ANODE 1.65 (0.065) DIA. 1.91 (0.075) 0.20 (0.008) MAX. 0.46 (0.018) 0.56 (0.022) 0.79 (0.031) 0.53 (0.021) 0.25 (0.010) MAX.* NOTE 2 0.63 (0.025) 0.38 (0.015) CATHODE STRIPE 2.08 (0.082) 2.34 (0.092) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. * REFER TO FIGURE 1 FOR DESIGN CONCERNS. CATHODE TAB NO. ANODE DOWN. YES. CATHODE DOWN. Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode Connection. 4 Absolute Maximum Ratings at TA = 25C DH AS Standard AlGaAs Red Red Parameter DC Forward Current [1] Peak Forward Current[2] High Eff. Red Orange Yellow 50 30 30 30 20 30 30 mA 1000 300 90 90 60 90 90 mA 6 6 6 V DC Forward Voltage (Resistor Lamps Only) 6 Reverse Voltage (IR = 100 A) High Perf. Emerald Green Green Units 5 5 5 5 5 5 5 V Transient Forward Current (10 s Pulse) 2000 500 500 500 500 500 500 mA Operating Temperature Range: Non-Resistor Lamps -55 to +100 -40 to +100 -40 to +100 -20 to +100 [3] Resistor Lamps Storage Temperature Range For Thru Hole Devices Wave Soldering Temperature [1.6 mm (0.063 in.) from body] For Surface Mount Devices: Convective IR Vapor Phase -55 to +100 -40 to +85 -55 to +100 C -20 to +85 C 260C for 5 Seconds 235C for 90 Seconds 215C for 3 Minutes Notes: 1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps. 2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions. 3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this high current. 5 Electrical/Optical Characteristics, TA = 25C Standard Red Device HLMP- Parameter 6000-E00xx Luminous Intensity Symbol Min. Typ. Max. Units [1] Iv 6000-G00xx All All All 0.5 1.2 1.3 3.2 mcd IF = 10 mA V IF = 10 mA IR = 100 A Forward Voltage VF 1.4 1.6 Reverse Breakdown Voltage VR 5.0 12.0 V 2.0 Test Conditions Included Angle Between Half Intensity Points[2] 21/2 90 Deg. Peak Wavelength PEAK 655 nm Dominant Wavelength[3] d 640 nm Spectral Line Half Width 1/2 24 nm Speed of Response s 15 ns Capacitance C 100 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 65 lm/W VF = 0; f = 1 MHz Junction-to-Cathode Lead 6 DH AS AlGaAs Red Device HLMP- Parameter Symbol Min. Typ. Max. Units P102-F00xx 1.0 20.0 P105-L00xx 8.6 30.0 Q100-N00xx 22.0 45.0 40 200 Q150-F00xx 1.0 1.8 Q155-F00xx 1.0 4.0 Q105-P00xx Luminous Intensity Q100 Forward Voltage Iv VF Q150/Q155 All Reverse Breakdown Voltage VR P105 Q100/Q150 Q105/Q155 All 5.0 IF = 20 mA mcd IF = 1 mA 1.8 2.2 1.6 1.8 15.0 Test Conditions V IF = 20 mA IF = 1 mA V IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 Peak Wavelength PEAK 645 nm Dominant Wavelength[3] d 637 nm Spectral Line Half Width 1/2 20 nm Speed of Response s 30 ns Exponential Time Constant; e-t/s Capacitance C 30 pF VF = 0; f = 1 MHz Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 80 lm/W 90 Deg. 28 Measured at Peak Junction-to Cathode Lead 7 High Efficiency Red Device HLMPParameter Symbol Min. Typ. Max. Units P202-F00xx 1.0 5.0 P205-F00xx 1.0 8.0 6300-F00xx 1.0 10.0 10.0 40.0 0.4 1.0 6600-G00xx 1.3 5.0 6620-F00xx 0.8 2.0 1.5 1.8 3.0 9.6 13.0 3.5 5.0 6305-L00xx 7000-D00xx Luminous Intensity All 6600 6620 All [1] Iv Forward Voltage (Nonresistor Lamps) VF Forward Current (Resistor Lamps) IF Reverse Breakdown Voltage VR P205 6305 30.0 IF = 10 mA mcd IF = 2 mA VF = 5.0 Volts V IF = 10 mA mA VF = 5.0 V V IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 PEAK 635 nm Dominant Wavelength[3] d 626 nm Spectral Line Half Width 1/2 40 nm Speed of Response s 90 ns Capacitance C 11 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 145 lm/W Peak Wavelength All 5.0 Test Conditions Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead 8 Orange Device HLMP- Parameter Symbol Min. Typ. Max. Units P402-F00xx P405-F00xx Luminous Intensity Iv Q400-F00xx All P405 4.0 1.0 6 1.0 8 Forward Voltage VF 1.5 1.9 Reverse Breakdown Voltage VR 5.0 30.0 Included Angle Between Half Intensity Points[2] 3.0 mcd IF = 10 mA V IF = 10 mA V IR = 100 A 125 21/2 Q400 Deg. 90 PEAK 600 nm d 602 nm 1/2 40 nm Speed of Response s 260 ns Capacitance C 4 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 380 lm/W Peak Wavelength Dominant Wavelength [3] Spectral Line Half Width All 1.0 Test Conditions Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead 9 Yellow Device HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions P302-F00xx 1.0 3.0 P305-F00xx 1.0 4.0 6400-F00xx 1.0 9.0 3.6 20 7019-D00xx 0.4 0.6 IF = 2 mA 6700-G00xx 1.4 5.0 VF = 5.0 Volts 6720-F00xx 0.9 2.0 6405-J00xx Luminous Intensity[1] All Iv Forward Voltage (Nonresistor Lamps) VF Forward Current (Resistor Lamps) IF Reverse Breakdown Voltage VR 6700 6720 All P305 6405 mcd 2.0 2.4 9.6 13.0 3.5 5.0 50.0 V IF = 10 mA mA VF = 5.0 V V 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 PEAK 583 nm d 585 nm 1/2 36 nm Speed of Response s 90 ns Capacitance C 15 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 500 lm/W Peak Wavelength Dominant Wavelength [3] Spectral Line Half Width All 5.0 IF = 10 mA Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead 10 High Performance Green Device HLMP- Parameter Symbol Min. Typ. Max. Units P502-F00xx 1.0 3.0 P505-G00xx 1.6 6.3 6500-F00xx 1.0 7.0 6505-L00xx 10.0 40.0 0.4 0.6 6800-G00xx 1.6 5.0 6820-F00xx 0.8 2.0 7040-D00xx Luminous Intensity[1] All Iv Forward Voltage (Nonresistor Lamps) VF Forward Current (Resistor Lamps) IF Reverse Breakdown Voltage VR 6800 6820 All P505 6505 IF = 10 mA mcd VF = 5.0 Volts 2.1 2.7 9.6 13.0 3.5 5.0 50.0 IF = 2 mA V IF = 10 mA mA VF = 5.0 V V IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 PEAK 565 nm d 569 nm 1/2 28 nm Speed of Response s 500 ns Capacitance C 18 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 595 lm/W Peak Wavelength Dominant Wavelength [3] Spectral Line Half Width All 5.0 Test Conditions VF = 0; f = 1 MHz Junction-to-Cathode Lead Notes: 1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous intensity for an array determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching between arrays. 2. 1/2 is the off-axis angle where the luminous intensity is half the on-axis value. 3. Dominant wavelength, d, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines the color of the device. 4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie =Iv/v, where Iv is the luminous intensity in candelas and v is the luminous efficacy in lumens/watt. 11 Emerald Green[1] Device HLMP- Parameter Symbol Min. Typ. Max. Units P605-F00xx Luminous Intensity Iv Q600-F00xx All P605 Forward Voltage VF Reverse Breakdown Voltage VR Included Angle Between Half Intensity Points[2] 1.5 1.0 1.5 2.2 5.0 3.0 mcd IF = 10 mA V IF = 10 mA V IR = 100 A 125 21/2 Q600 Deg. 90 PEAK 558 nm d 560 nm 1/2 24 nm Speed of Response s 3100 ns Capacitance C 35 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 656 lm/W Peak Wavelength Dominant Wavelength P605/ Q600 1.0 Test Conditions [3] Spectral Line Half Width Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead Note: 1. Please refer to Application Note 1061 for information comparing standard green and emerald green light ouptut degradation. 12 Figure 1. Relative Intensity vs. Wavelength. High Efficiency Red, Orange, Yellow, High Performance Green, and Emerald Green Standard Red and DH AS AlGaAs Red 100 FORWARD CURRENT - mA 90 HIGH EFFICIENCY RED/ORANGE 80 70 60 YELLOW 50 40 30 HIGH PERFORMANCE GREEN, EMERALD GREEN 20 10 0 0 0.5 1 1.5 2 2.5 3 3.5 FORWARD VOLTAGE - V Figure 2. Forward Current vs. Forward Voltage. (Non-Resistor Lamp) Standard Red, DH As AlGaAs Red Low Current Figure 3. Relative Luminous Intensity vs. Forward Current. (Non-Resistor Lamp) HER, Orange, Yellow, and High Performance Green, and Emerald Green 13 Standard Red DH As AlGaAs Red HER, Orange, Yellow, and High Performance Green, and Emerald Green Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current (Non-Resistor Lamps). Figure 5. Maximum Forward dc Current vs. Ambient Temperature. Derating Based on TJ MAX = 110 C (Non-Resistor Lamps). Standard Red HER, Orange, Yellow, and High Performance Green DH As AlGaAs Red Figure 6. Maximum Tolerable Peak Current vs. Pulse Duration. (IDC MAX as per MAX Ratings) (Non-Resistor Lamps). 14 Figure 7. Resistor Lamp Forward Current vs. Forward Voltage. Figure 9. Relative Intensity vs. Angular Displacement. Figure 8. Resistor Lamp Luminous Intensity vs. Forward Voltage. www.semiconductor.agilent.com Data subject to change. Copyright (c) 2000 Agilent Technologies, Inc. December 29, 2000 Obsoletes 5968-7825E 5980-2149E Subminiature Right Angle LED Indicators Technical Data Option 10 Features * Ideal for PC Board Status Indication * Side Stackable on 2.54 mm (0.100 in.) Centers * Available in Four Colors * Housing Meets UL 94V-O Flammability Rating * Additional Catalog Lamps Available as Options Package Dimensions Description The Agilent Technolgies series of Subminiature Right Angle Indicators are industry standard status indicators that incorporate tinted diffused LED lamps in black plastic housings. The 2.54 mm (0.100 in.) wide packages may be side stacked for maximum board space savings. The solder plated leads are in line on 2.54 mm (0.100 in.) centers, a standard spacing that makes the PC board layout straight-forward. These products are designed to be used as back panel diagnostic indicators and logic status indicators on PC boards. Ordering Information To order Subminiature Right Angle indicators, order the base part number and add the option code 10. Example: HLMP-6300F0010. For price and delivery on Resistor Subminiature Right Angle Indicators and other subminiature LEDs not indicated above, please contact your nearest Agilent Components representative. Absolute Maximum Ratings and Other Electrical/Optical Characteristics The absolute maximum ratings and typical device characteristics are identical to those of the Subminiature lamps. For information about these characteristics, see the data sheets of the equivalent Subminiature lamp. Note: Option 10 is not applicable for all AlInGaP and InGaN devices. HLMX-XXXX-X X X X X Packaging Option Color Bin Selection Max. Iv Bin Min. Iv Bin 4 x 4 Prod. Part Number www.semiconductor.agilent.com Data subject to change. Copyright (c) 2001 Agilent Technologies, Inc. January 25, 2001 Obsoletes 5968-0056E (11/99) 5988-2176EN