HLMP-6300-F00 - Avago Technologies

Dome Packages

The HLMP-6xxx Series dome

lamps for use as indicators use

a tinted, diffused lens to

provide a wide viewing angle

with a high on-off contrast

ratio. High brightness lamps

use an untinted, nondiffused

lens to provide a high luminous

intensity within a narrow

radiation pattern.

Resistor Lamps

The HLMP-6xxx Series 5 volt

subminiature lamps with built

in current limiting resistors are

for use in applications where

space is at a premium.

Lead Configurations

All of these devices are made by

encapsulating LED chips on

axial lead frames to form

molded epoxy subminiature

lamp packages. A variety of

package configuration options is

Features

• Subminiature Flat Top

Package

Ideal for Backlighting and

Light Piping Applications

• Subminiature Dome

Package

Diffused Dome for Wide

Viewing Angle

Nondiffused Dome for High

Brightness

• TTL and LSTTL

Compatible 5 Volt Resistor

Lamps

• Available in Six Colors

• Ideal for Space Limited

Applications

• Axial Leads

• Available with Lead

Configurations for Surface

Mount and Through Hole

PC Board Mounting

Description

Flat Top Package

The HLMP-Pxxx Series flat top

lamps use an untinted, non-

diffused, truncated lens to

provide a wide radiation

pattern that is necessary for

use in backlighting

applications. The flat top lamps

are also ideal for use as

emitters in light pipe

applications.

Subminiature LED Lamps

Technical Data

HLMP-Pxxx Series

HLMP-Qxxx Series

HLMP-6xxx Series

HLMP-70xx Series

available. These include special

surface mount lead configura-

tions, gull wing, yoke lead or Z-

bend. Right angle lead bends at

2.54 mm (0.100 inch) and

5.08 mm (0.200 inch) center

spacing are available for

through hole mounting. For

more information refer to

Standard SMT and Through

Hole Lead Bend Options for

Subminiature LED Lamps data

sheet.

DH AS High High Device

Standard AlGaAs Efficiency Perf. Emerald Outline

Red Red Red Orange Yellow Green Green Device Description[1] Drawing

P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A

Flat Top

P102 P202 P402 P302 P502 Untinted, Diffused, A

Flat Top

6000 Q100 6300 Q400 6400 6500 Q600 Tinted, Diffused B

Q105 6305 6405 6505 Untinted, Nondiffused, B

High Brightness

Q150 7000 7019 7040 Tinted, Diffused, Low B

Current

Q155 Nondiffused, Low B

Current

6600 6700 6800 Tinted, Diffused, B

Resistor, 5 V, 10 mA

6620 6720 6820 Diffused, Resistor, 5 V, B

4 mA

Device Selection Guide

Part Number: HLMP-xxxx

HLMX-XXXX-X X X X X

4 x 4

Prod.

Part

Number

Min. Iv

Bin

Max. Iv

Bin

Color Bin

Selection

Packaging

Option

Ordering Information

Package Dimensions (cont.)

(B) Diffused and Nondiffused

Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from

Shorting to Anode Connection.

Package Dimensions

(A) Flat Top Lamps

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).

2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

0.50 (0.020) REF. 0.94

1.24

(0.037)

(0.049)

2.92 (0.115)

MAX.

0.76

0.89

(0.030)

(0.035) R.

0.63

0.38

(0.025)

(0.015)

2.03 (0.080)

1.78 (0.070)

0.79 (0.031)

0.53 (0.021)

0.46

0.56

(0.018)

(0.022)

0.25 (0.010) MAX.*

NOTE 2

0.20 (0.008) MAX.

CATHODE

1.65

1.91

(0.065)

(0.075) DIA.

ANODE

11.68

10.67

(0.460)

(0.420)

BOTH SIDES

0.18

0.23

(0.007)

(0.009)

2.08

2.34

(0.082)

(0.092)

CATHODE

STRIPE

2.21

1.96

(0.087)

(0.077)

* REFER TO FIGURE 1 FOR DESIGN CONCERNS.

NO. ANODE DOWN. YES. CATHODE DOWN.

CATHODE

TAB

0.46

0.56

(0.018)

(0.022)

1.40

1.65

(0.055)

(0.065)

0.25 (0.010) MAX.*

NOTE 2

0.20 (0.008) MAX.

0.50 (0.020) REF.

CATHODE

1.65

1.91

(0.065)

(0.075) DIA.

ANODE

11.68

10.67

(0.460)

(0.420)

BOTH SIDES

1.14

1.40

(0.045)

(0.055) 0.63

0.38

(0.025)

(0.015)

2.21

1.96

(0.087)

(0.077)

0.18

0.23

(0.007)

(0.009)

0.79 (0.031) MAX.

2.44

1.88

(0.096)

(0.074)

2.08

2.34

(0.082)

(0.092)

CATHODE

STRIPE

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).

2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

* REFER TO FIGURE 1 FOR DESIGN CONCERNS.

DH AS High High

Standard AlGaAs Eff. Perf. Emerald

Parameter Red Red Red Orange Yellow Green Green Units

DC Forward Current[1] 50 30 30 30 20 30 30 mA

Peak Forward Current[2] 1000 300 90 90 60 90 90 mA

DC Forward Voltage 6 6 6 6 V

(Resistor Lamps Only)

Reverse Voltage (IR = 100 µA)5 555555V

Transient Forward Current[3] 2000 500 500 500 500 500 500 mA

(10 µs Pulse)

Operating Temperature Range: -55 to -40 to -55 to +100 -40 to -20 to

Non-Resistor Lamps +100 +100 +100 +100 °C

Resistor Lamps -40 to +85 -20 to

+85

Storage Temperature Range °C

For Thru Hole Devices 260°C for 5 Seconds

Wave Soldering Temperature

[1.6 mm (0.063 in.) from body]

For Surface Mount Devices:

Convective IR 235°C for 90 Seconds

Vapor Phase 215°C for 3 Minutes

Absolute Maximum Ratings at TA = 25°C

-55 to +100

Notes:

1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.

2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.

3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not

operate these lamps at this high current.

Electrical/Optical Characteristics, TA = 25°C

Standard Red

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

6000-E00xx Luminous Intensity[1] Iv0.5 1.2 mcd IF = 10 mA

6000-G00xx 1.3 3.2

Forward Voltage VF1.4 1.6 2.0 V IF = 10 mA

All Reverse Breakdown VR5.0 12.0 V IR = 100 µA

Voltage

Included Angle Between

All Half Intensity Points[2] 2θ1/290 Deg.

Peak Wavelength λPEAK 655 nm

Dominant Wavelength[3] λd640 nm

Spectral Line Half Width ∆λ1/2 24 nm

All Speed of Response τs15 ns

Capacitance C 100 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv65 lm/W

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P102-F00xx 1.0 20.0

P105-L00xx 8.6 30.0

Q100-N00xx 22.0 45.0

Q105-P00xx Luminous Intensity Iv40 200 mcd

Q150-F00xx 1.0 1.8

Q155-F00xx 1.0 4.0

Q100 Forward Voltage VF1.8 2.2 V IF = 20 mA

Q150/Q155 1.6 1.8 IF = 1 mA

All Reverse Breakdown VR5.0 15.0 V IR = 100 µA

Voltage

P105 125

Q100/Q150 Included Angle Between 2θ1/290 Deg.

Half Intensity Points[2]

Q105/Q155 28

Peak Wavelength λPEAK 645 nm Measured at Peak

Dominant Wavelength[3] λd637 nm

Spectral Line Half Width ∆λ1/2 20 nm

All Speed of Response τs30 ns Exponential Time

Constant; e-t/τ

Capacitance C 30 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to

Cathode Lead

Luminous Efficacy[4] ηv80 lm/W

DH AS AlGaAs Red

IF = 1 mA

IF = 20 mA

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P202-F00xx 1.0 5.0

P205-F00xx 1.0 8.0

6300-F00xx 1.0 10.0 IF = 10 mA

6305-L00xx 10.0 40.0

7000-D00xx Luminous Intensity[1] Iv0.4 1.0 mcd IF = 2 mA

6600-G00xx 1.3 5.0 VF = 5.0 Volts

6620-F00xx 0.8 2.0

All Forward Voltage VF1.5 1.8 3.0 V IF = 10 mA

(Nonresistor Lamps)

6600 9.6 13.0

IFmA VF = 5.0 V

6620 3.5 5.0

All Reverse Breakdown VR5.0 30.0 V IR = 100 µA

Voltage

P205 125

6305 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused

Peak Wavelength λPEAK 635 nm Measured at Peak

Dominant Wavelength[3] λd626 nm

Spectral Line Half Width ∆λ1/2 40 nm

All Speed of Response τs90 ns

Capacitance C 11 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv145 lm/W

High Efficiency Red

Forward Current

(Resistor Lamps)

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P402-F00xx 1.0 4.0

P405-F00xx Luminous Intensity Iv1.0 6 mcd IF = 10 mA

Q400-F00xx 1.0 8

Forward Voltage VF1.5 1.9 3.0 V IF = 10 mA

All Reverse Breakdown VR5.0 30.0 V IR = 100 µA

Voltage

P405 Included Angle Between 125

Half Intensity Points[2] 2θ1/2Deg.

Q400 90

Peak Wavelength λPEAK 600 nm

Dominant Wavelength[3] λd602 nm Measured at Peak

Spectral Line Half Width ∆λ1/2 40 nm

All Speed of Response τs260 ns

Capacitance C 4 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv380 lm/W

Orange

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P302-F00xx 1.0 3.0

P305-F00xx 1.0 4.0 IF = 10 mA

6400-F00xx 1.0 9.0

6405-J00xx Luminous Intensity[1] Iv3.6 20 mcd

7019-D00xx 0.4 0.6 IF = 2 mA

6700-G00xx 1.4 5.0 VF = 5.0 Volts

6720-F00xx 0.9 2.0

All Forward Voltage VF2.0 2.4 V IF = 10 mA

(Nonresistor Lamps)

6700 9.6 13.0

Forward Current IFmA VF = 5.0 V

6720 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown VR5.0 50.0 V

Voltage

P305 125

6405 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused

Peak Wavelength λPEAK 583 nm Measured at Peak

Dominant Wavelength[3] λd585 nm

Spectral Line Half Width ∆λ1/2 36 nm

All Speed of Response τs90 ns

Capacitance C 15 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv500 lm/W

Yellow

High Performance Green

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P502-F00xx 1.0 3.0

P505-G00xx 1.6 6.3

6500-F00xx 1.0 7.0 IF = 10 mA

6505-L00xx 10.0 40.0

7040-D00xx Luminous Intensity[1] Iv0.4 0.6 mcd IF = 2 mA

6800-G00xx 1.6 5.0 VF = 5.0 Volts

6820-F00xx 0.8 2.0

All Forward Voltage VF2.1 2.7 V IF = 10 mA

(Nonresistor Lamps)

6800 9.6 13.0

Forward Current IFmA VF = 5.0 V

6820 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown VR5.0 50.0 V IR = 100 µA

Voltage

P505 125

6505 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused Peak Wavelength λPEAK 565 nm

Dominant Wavelength[3] λd569 nm

Spectral Line Half Width ∆λ1/2 28 nm

All Speed of Response τs500 ns

Capacitance C 18 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv595 lm/W

Notes:

1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous

intensity for an array determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching

between arrays.

2. θ1/2 is the off-axis angle where the luminous intensity is half the on-axis value.

3. Dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines

the color of the device.

4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie =Iv/ηv, where Iv is the luminous intensity in

candelas and ηv is the luminous efficacy in lumens/watt.

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P605-F00xx Luminous Intensity Iv1.0 1.5 mcd IF = 10 mA

Q600-F00xx 1.0 1.5

Forward Voltage VF2.2 3.0 V IF = 10 mA

All Reverse Breakdown VR5.0 V IR = 100 µA

Voltage

P605 Included Angle Between 125

Half Intensity Points[2] 2θ1/2Deg.

Q600 90

Peak Wavelength λPEAK 558 nm

Dominant Wavelength[3] λd560 nm Measured at Peak

Spectral Line Half Width ∆λ1/2 24 nm

P605/

Q600 Speed of Response τs3100 ns

Capacitance C 35 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv656 lm/W

Emerald Green[1]

Note:

1. Please refer to Application Note 1061 for information comparing standard green and emerald green light ouptut degradation.

Standard Red, DH As AlGaAs Red

Standard Red and DH AS

AlGaAs Red

High Efficiency Red, Orange,

Yellow, High Performance

Green, and Emerald Green

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

Low Current

Figure 1. Relative Intensity vs. Wavelength.

Figure 2. Forward Current vs. Forward Voltage. (Non-Resistor Lamp)

Figure 3. Relative Luminous Intensity vs. Forward Current. (Non-Resistor Lamp)

FORWARD CURRENT – mA

100

FORWARD VOLTAGE – V

0.5 1 1.5 2 2.5 3 3.5

HIGH

PERFORMANCE

GREEN,

EMERALD

GREEN

YELLOW

HIGH EFFICIENCY

RED/ORANGE

Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current (Non-Resistor Lamps).

Figure 5. Maximum Forward dc Current vs. Ambient Temperature. Derating Based on TJ MAX =

110°C (Non-Resistor Lamps).

Figure 6. Maximum Tolerable Peak Current vs. Pulse Duration. (IDC MAX as per MAX Ratings) (Non-Resistor

Lamps).

Standard Red

DH As AlGaAs RedStandard Red

HER, Orange, Yellow, and High

Performance Green DH As AlGaAs Red

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

Figure 9. Relative Intensity vs. Angular Displacement.

Figure 7. Resistor Lamp Forward Current vs. Forward

Voltage. Figure 8. Resistor Lamp Luminous Intensity vs.

Forward Voltage.

www.semiconductor.agilent.com

Data subject to change.

December 29, 2000

Obsoletes 5968-7825E

5980-2149E

Subminiature Right Angle LED

Indicators

Technical Data

Features

• Ideal for PC Board Status

Indication

• Side Stackable on 2.54 mm

(0.100 in.) Centers

• Available in Four Colors

• Housing Meets UL 94V-O

Flammability Rating

• Additional Catalog Lamps

Available as Options

Description

The Agilent Technolgies series of

Subminiature Right Angle

Indicators are industry standard

status indicators that incorporate

tinted diffused LED lamps in

black plastic housings. The 2.54

mm (0.100 in.) wide packages

may be side stacked for maximum

board space savings. The solder

Package Dimensions

Option 10

plated leads are in line on 2.54

mm (0.100 in.) centers, a

standard spacing that makes the

PC board layout straight-forward.

These products are designed to be

used as back panel diagnostic

indicators and logic status

indicators on PC boards.

Absolute Maximum

Ratings and Other

Electrical/Optical

Characteristics

The absolute maximum ratings

and typical device characteristics

are identical to those of the

Subminiature lamps. For

information about these

characteristics, see the data

sheets of the equivalent

Subminiature lamp.

Ordering Information

To order Subminiature Right

Angle indicators, order the base

part number and add the option

code 10. Example: HLMP-6300-

F0010. For price and delivery on

Resistor Subminiature Right

Angle Indicators and other

subminiature LEDs not indicated

above, please contact your

nearest Agilent Components

representative.

Note: Option 10 is not applicable

for all AlInGaP and InGaN

devices.

www.semiconductor.agilent.com

Data subject to change.

January 25, 2001

Obsoletes 5968-0056E (11/99)

5988-2176EN

HLMX-XXXX-X X X X X

4 x 4 Prod.

Part

Number

Min. Iv Bin

Max. Iv Bin

Color Bin

Selection

Packaging

Option